ProLights RA3000PROFILE Manuale utente

USER MANUAL

MANUALE UTENTE

RA3000PROFILE

LED MOVING PROFILE

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.02-12/19

1

RA3000PROFILE

Packing content

• RA3000PROFILE

• Power cable

• Mount bracket

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Introduction

1. 1 Description 1. 1 Description

1. 2 Technical specications1. 2 Technical specications

1. 3 Operating elements and connections1. 3 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 Linking3. 4 Linking

3. 5 DMX addressing conguration3. 5 DMX addressing conguration

3. 6 DMX mode conguration3. 6 DMX mode conguration

3. 7 DMX addressing 3. 7 DMX addressing

3. 8 Wireless settings3. 8 Wireless settings

3. 9 Ethernet 3. 9 Ethernet

3. 10 Movement3. 10 Movement

3. 11 Screen 3. 11 Screen

3. 12 Fixture settings3. 12 Fixture settings

3. 13 Auto and manual test3. 13 Auto and manual test

3. 14 Reset of the function3. 14 Reset of the function

3. 15 Adjust3. 15 Adjust

3. 16 Informaion of the device3. 16 Informaion of the device

3. 17 Connection of the DMX line 3. 17 Connection of the DMX line

3. 18 Construction of the DMX termination 3. 18 Construction of the DMX termination

3. 19 DMX control3. 19 DMX control

3. 20 Color - Gobos wheel 3. 20 Color - Gobos wheel

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement4. 2 Fuse replacement

4. 3 Trouble shooting4. 3 Trouble shooting

2

3

6

7

8

9

12

13

14

15

16

17

18

23

24

25

RA3000PROFILE

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with

.

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

RA3000PROFILE

- 1 - INTRODUCTION

1.1 DESCRIPTION

Ra 3000Prole combines solid-state technology in every single detail and it has been specically engi-

neered to be not only a high-quality bright light but also silent. Ra 3000Prole is able to provide a real

25’000 lumen output with unprecedented beam evenness.

The 6.000 KLED engine has been custom designed to make the Ra 3000Prole hit a CRI of 90, TLCI of 92,

high R9 and TM30 making all skin tones and colours come to lifeon stage or in front of a camera.

The Ra 3000Prole’s CMY system delivers beautiful pastels, stunning saturated colours, powerful prima-

ries, one colour wheel provides split colours, and linear CTO allows the Ra 3000Prole to blend in with

traditional sources.

Packed with a full feature set, composed of a gobo wheel, animation wheel, iris, prism and dual linear

frost.

High-precision 4 blade shuttering system can be overlaid to provide endless combinations. The 19

element optics of the RA3000PROFILE are precision engineered for a perfect zoom, ideal edges and

maximum eciency.

The RA3000PROFILE is silent, bright, exible and precise.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 1.000W White LED

• CCT: 6.000K

• CRI: > 90

• R9: 75

• Luminous ux: 25’000lm

• Lux: (6°) 83’500 lx (50°) 1’830lx @5 m

• Source life expectancy: 50.000 h

• Other: TLCI: 92; TM30-15RF: 88; TM30RG: 99

OPTICS

• Zoom: 6° - 50° motorised linear zoom

• Lens diameter: 180mm

COLOUR SYSTEM

• Colour mixing: linear CMY

• CTC: linear CTO correction 3.000 K ~ 6.000 K

• Colour wheel: 6 colour lters

DYNAMIC EFFECTS

• Shutter system: 4 single blades: + / - 35°, complete system: + / - 45°

• Animation wheel: animation wheel with CW and CCW rotation

• Rotating gobos: 6 rotating gobos + open, interchangeable, indexing

• Gobo size: outer: 31,6 mm - image: 26 mm - thickness: 1,1 mm

• FX generator: shutter macros with adjustable speed

• Circular prism: 4f with bi-directional rotation, indexing

• Frost: dual frost lter system, 1° soft-edge frost gobo, 5° frost wash, with linear 0 - 100% frost lter

• Iris: 5 - 100% motorised iris

RA3000PROFILE

4

BODY

• Pan angle: 540°

• Tilt angle: 270°

• Pan/Tilt resolution: 8 / 16 bit

• Feedback: automatic repositioning after accidental movement

• Body: ame retardant PC

• Body colour: black

CONTROL

• Protocols: DMX512, RDM, Art-Net, W-DMX

• DMX channels: 38 / 39 / 40 / 41channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for xture remote monitor and settings

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Strobe / shutter: 1 - 30 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 1.288W

• Power consumption (at 120 V): 1.371W

• Power factor: (120 W) 1,0 - (230 W) 0,97

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and xing: fast quick lock Omega bracket

• Pan / tilt lock: pan / tilt locking for transportation and maintenance

• Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors

• Data connection: Art-Net RJ45 IN/OUT

• Power connection: Neutrik powerCON TRUE1 IN connector

• IP rating: 20

• Dimensions (WxHxD): 535x913x403mm

• Weight: 57kg

5

RA3000PROFILE

510mm

20,07in

914mm

35,98in

534mm

21,02in

402mm

15,82in

Illuminance at a Distance

6° - 50°

Lux Center Beam Angle: 6° - 50° Beam

Width

3m

5m

7m

10m

0m

231944/5083lx

83500/1830lx

42602/934lx

20875/458lx

0.309/2.73m

0.515/4.55m

0.721/6.37m

1.03/9.10m

Photometric data

Technical drawing

Fig.1

RA3000PROFILE

6

1

2

3

5

4

A

B

6

7

9

10

8

9

11

12

13

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. MOVING HEAD

2. ROTARY ARM

3. TILT Mechanism Lock and Release

4. PAN Mechanism Lock and Release

5. HANDLE

6. CONTROL PANEL with TFT display

and 5 button used to access

the control panel functions and

manage them.

7. POWER IN (PowerCON TRUE

IN): for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

8. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

9. EtherCON CONNECTORS IN / OUT

signal.

10. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

11. DMX OUT ( 3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

12. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C.

13. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C.

View A

View B

Fig.2

7

RA3000PROFILE

- 2 - INSTALLATION

2.1 MOUNTING

The RA3000PROFILE may be set up on a solid and even surface. By means of the xing facilities of the

baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For

xing, stable mounting clips are required. According to the gure, the bolts of the brackets are placed into

the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure

that the unit is rmly xed to avoid vibration and slipping while operating. The mounting place must be of

sucient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the xture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

Fig.3

CLAMP

OMEGA

RA3000PROFILE

8

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the RA3000PROFILE is ready for operation. To

switch o, disconnect the mains plug from the socket. For a more convenient operation it is recommend-

ed to connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The control panel of RA3000PROFILE has a display and 5 buttons for the complete programming and

management of the projector menu (g.4).

Fig.4 - Functions of the buttons and display icons

UP DOWN LEFT RIGHT ENTER

Increases the value

displayed or passes

to the previous item

in a menu

Decreases the value

displayed or passes

to the next item in

the menu

Return to the top

level

Commute from

units, tens, hundred

in the menu

Conrms the

displayed value,

or activates the

displayed function,

or enters the

successive menu

OK

9

RA3000PROFILE

3.3 MENU STRUCTURE

MENU

1 CONNECT

ð

Address

ð

Value (1-472)

DMX Mode

ð

Standard 38Ch

Standard 40Ch

Extended 39Ch

Extended 41Ch

Extended 42Ch

Wireless

ð

Receive On/O

ð

ON/OFF

Receive Reset

ð

NO/YES

Wireless to DMX

ð

NO/YES

Ethernet

ð

Protocol

ð

Art-NEt

sACN

Universe

ð

Value Art-NEt (000-255)

Value sACN (001-255)

Start Channel

ð

Value (001-512)

IP Address

ð

2.161.129.195/10.161.129.195

Ethernet to DMX

ð

YES/NO

2 SET UP

ð

Movement

ð

Pan Reverse

ð

NO/YES

Tilt Reverse

ð

NO/YES

Pan Feedback

ð

NO/YES

Tilt Feedback

ð

NO/YES

Screen

ð

Backlight

ð

On/10s/20s/ 30s

Flip Display

ð

NO/YES/AUTO

Warn Cue

ð

ON/OFF

Key Lock

ð

NO/YES

Fixture

ð

Dimmer Mode

ð

OFF/Dimmer 1/Dimmer 2/Dimmer 3

Fan Mode

ð

Auto/High /Silent/O

Temperature unit

ð

°C /°F

Auto Test

ð

Auto Test …

Manual Test

ð

Pan

ð

Value (000-255)

Pan Fine

ð

Value (000-255)

Tilt

ð

Value (000-255)

Tilt Fine

ð

Value (000-255)

P/T Speed

ð

Value (000-255)

Dimmer

ð

Value (000-255)

Shutter

ð

Value (000-255)

Cyan

ð

Value (000-255)

Magenta

ð

Value (000-255)

Yellow

ð

Value (000-255)

RA3000PROFILE

10

CTO

ð

Value (000-255)

Color

ð

Value (000-255)

Gobo

ð

Value (000-255)

RGobo

ð

Value (000-255)

PrismRot.

ð

Value (000-255)

Eect

ð

Value (000-255)

REect

ð

Value (000-255)

Focus

ð

Value (000-255)

Zoom

ð

Value (000-255)

Frost 1

ð

Value (000-255)

Frost 2

ð

Value (000-255)

Iris

ð

Value (000-255)

Fr.shutters Rot.

ð

Value (000-255)

Fr.shutter 1 Move.

ð

Value (000-255)

Fr.shutter 1 Swiv.

ð

Value (000-255)

Fr.shutter 2 Move.

ð

Value (000-255)

Fr.shutter 2 Swiv.

ð

Value (000-255)

Fr.shutter 3 Move.

ð

Value (000-255)

Fr.shutter 3 Swiv.

ð

Value (000-255)

Fr.shutter 4 Move.

ð

Value (000-255)

Fr.shutter 4 Swiv.

ð

Value (000-255)

3 ADVANCED

ð

Reset

ð

All

Pan

Tilt

Cyan

Magenta

Yellow

CTO

Color

Gobo

Prism

Eect

Focus

Zoom

Frost

Iris

Fr.shutters Rot.

Fr.shutter 1 M1

Fr.shutter 1 M2

Fr.shutter 2 M1

Fr.shutter 2 M2

Fr.shutter 3 M1

Fr.shutter 3 M2

Fr.shutter 4 M1

Fr.shutter 4 M2

ð

Value (000-255)

11

RA3000PROFILE

Adjust

ð

Pan

Tilt

Cyan

Magenta

Yellow

CTO

Color

Gobo

RGobo

Prism

Rot Prism

Eect

Focus

Zoom

Frost 1

Frost 2

Iris

Fr.shutters Rot.

Fr.shutter 1 M1

Fr.shutter 1 M2

Fr.shutter 2 M1

Fr.shutter 2 M2

Fr.shutter 3 M1

Fr.shutter 3 M2

Fr.shutter 4 M1

Fr.shutter 4 M2

ð

Value (000-255)

Factory Reload

ð

NO/YES

ð

Value (000-255)

4 INFORMATION

ð

Fixture Time 0-9999

Temperature 58 °C

Fans Speed **%

Software Version DISP- V0.3

NET-V0.2

CTR1-XY- V0.2

CTR2-LED-V0.2

CTR3-MOTOR-V0.2

CTR4-MOTOR-V0.2

CTR5-MOTOR-V0.2

CTR6-MOTOR-V0.2

CTR7-MOTOR-V0.2

UID

ð

15D00221****

View DMX

RA3000PROFILE

12

3.4 LINKING

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit.

1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.5 DMX ADDRESSING CONFIGURATION

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conrm the setting.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.6 DMX MODE CONFIGURATION

RA3000PROFILE has 4 DMX channel congurations that can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Connect icon, then press the ENTER

button to enter the next DMX Mode menu.

• Press the ENTER button and select DMX Mode with the UP/ DOWN button, then conrm the selection with

the ENTER button.

• Use the UP/DOWN button to select the desired DMX channel conguration (Standard 38Ch, Standard 40Ch,

Extended 39Ch, Extended 41Ch, Extended 42Ch), then press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

The tables on page 20 indicate the operating modes and related DMX values. As a DMX interface, the unit

has 3 and 5-pin XLR contacts.

3.7 DMX ADDRESSING

For operation via a light control unit with DMX512 protocol, simply connect

RA3000PROFILE to the controller. The projector has a DMX channel conguration that can be accessed

from the control panel. In order to control RA3000PROFILE with a light control unit, the DMX start address

must be set for the rst DMX channel.

If, for example, address 33 is provided on the control unit to control the function of the rst one

DMX channel, the start address 33 must be set on the RA3000PROFILE. The other panel functions will be

automatically assigned to the following addresses.

13

RA3000PROFILE

3.8 WIRELESS SETTINGS

To enter the wireless setting mode press the ENTER button until the display shows Connect, then select

Wireless, then press the ENTER button.

Select the Wireless Receive function using the UP/DOWN buttons, then press the ENTER button.

To activate the Wireless reception mode, use the UP/DOWN buttons and select the On option.

• Press the ENTER button to conrm the selection.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

NOTE - Once you have performed these steps, you must synchronize with any WiFi unit with which you

want to communicate by pressing the sync button on it. At this point connect the DMX console to the WiFi

unit to open the communication with the RA3000PROFILE.

To reset the unit, select the Wireless Reset function using the UP/DOWN buttons, press the ENTER button

until the display shows Connect, then select Wireless, then press the ENTER button.

• Select the Wireless Reset function using the UP/DOWN buttons, then press the ENTER button.

To activate the mode use the UP / DOWN keys and select the Yes option.

• Press the ENTER button to conrm the selection.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

To activate the Wireless to DMX function, use the UP / DOWN buttons to press the ENTER button until the

display shows Connect, then select Wireless, then press the ENTER button.

• Select the Wireless to DMX function using the UP/DOWN buttons, then press the ENTER button.

To activate the mode use the UP/DOWN buttons and select the Yes option.

• Press the ENTER button to conrm the selection.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

3.9 ETHERNET

For the ArtNet settings to be assigned to the unit, refer to the following menu section.

• Press the UP/DOWN button to scroll through the menu, select Connect, then press the ENTER button ac-

cess the next Ethernet menu with the UP / DOWN button, then press the ENTER button.

• Use the UP/DOWN buttons to select one of the following settings: Universe, Start Channel, IP Address, Ethernet

to DMX.

• Press the ENTER button to conrm the selection and enter the sub menu.

• Set the desired value for the selected function using the UP/DOWN buttons. Then press

Fig.5 - Example of a DMX 38-channel conguration

DMX Address: 185DMX Address: 109DMX Address: 71 DMX Address: 147

. . . . . . . . . . . .

DMX512 Controller

RA3000PROFILE

14

the ENTER button.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

3.10 MOVEMENT

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button

access the next menu.

• Press the UP/DOWN button to select Movement and press the ENTER button to proceed.

• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm.

- Pan Reverse - Rotation in the opposite direction of the moving head. NO to deactivate the function

(normal setting); YES to activate the function (Pan Reverse).

- Tilt Reverse - Inclination in the opposite direction of the moving head. NO to deactivate the function

(normal setting), YES to activate the function (Tilt Reverse).

- Pan/Tilt Feedbacks - Rearrange Pan/Tilt position after accidental shift. Select NO for deactivate the func-

tion or YES to activate the function.

• Press the ENTER button to conrm the selection.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

3.11 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button

access the next menu.

• Press the UP/DOWN button to select Screen and press the ENTER button to proceed.

• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically

the backlighting of the display after a certain time which can be set using the directional keys. To have

the display always on select On or set a value between those shown (10s, 20s, 30s) to turn o the dis-

play once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select YES to activate the function or NO to

deactivate it.

- Warn Cue - Warning of error. Use the arrow keys to select OFF or ON depending on whether or not the

display shows error warnings.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands:

UP, DOWN, UP, DOWN, ENTER, ENTER. Select YES to activate the function or NO to deactivate it.

• Press the ENTER button to conrm the selection.

• Press the LEFT key repeatedly to exit the menu and to save the changes made.

3.12 FIXTURE

Dimmer Mode - select this function to choose and simulate dierent dimming curves:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button

access the next menu.

• Press the UP/DOWN button to select Fixture and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select Dimmer mode and press the ENTER

button to conrm.

15

RA3000PROFILE

• Press the UP/DOWN button to select the mode (OFF - DIMMER1 - DIMMER2 - DIMMER3), then press the EN-

TER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

- Fans Mode - select this function to set the fan operating mode:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button

access the next menu.

• Press the UP/DOWN button to select FIXTURE and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select Fans Mode and press the ENTER

button to conrm.

• Press the UP/DOWN button to select the Auto High mode, then press the ENTER button to conrm your

choice.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

- Theater Mode - Select this function for theatrical situations or in which you want less noise; the output

of the LED will be limited to limit the heating and the fans:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Set Up icon, then press the ENTER

button to access the next menu.

• Press the UP/DOWN button to select Fixture and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select Theater Mode and press the ENTER

button to conrm.

• Press the UP/DOWN button to select the desired option (Auto / Silent / O), then press the ENTER button

to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

- Temperature - Select this function to set the unit of measurement of the temperature shown on the

display:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Set Up icon, then press the ENTER

button to access the next menu.

• Press the UP/DOWN button to select FIXTURE and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select Temperature °C/F and press the

ENTER button to conrm.

• Press the UP / DOWN button to select the Celsius / Fahrenheit measurement unit, then press the ENTER

button to conrm the selection.

• Press the LEFT buttton repeatedly to exit the menu and to save the changes made.

3.13 AUTO E MANUAL TEST

Through these menus it is possible to test the functioning of all the functions of the moving head.

3.14 RESET OF THE FUNCTIONS

You can start a preset program to restore the selected function:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Advanced icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to select Reset and press the ENTER button to access the next menu.

• Press the UP/DOWN button to scroll through the menu, then select the function you want to reset

between those.

• Press the ENTER button to conrm the selection and wait for the selected function to be restored.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

RA3000PROFILE

16

3.15 ADJUST

This function allows you to change all parameters. Press the UP/DOWN buttons to select one of the param-

eters and press ENTER to change its value (000-999) using the UP/DOWN buttons.

Press the ENTER button to conrm your choice.

Press the LEFT button repeatedly to exit the menu and to save the changes made.

3.16 INFORMATION ON THE DEVICE

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to select Information, then press the ENTER button to access the next

menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Fixture Time function, the operating time of the projector can be shown on the

display.

- Temperature - Through the Temperature function it is possible to display on the display the temperature

inside the moving head, where the lamp is located. The temperature can be displayed in degrees Celsius

or Fahrenheit.

- Fans Speed - Through the Fans Speed function it is possible to display on the display the fan speed present

near the lamp. The speed measurement is expressed in RPM (revolutions per minute).

- Software Version - Through the Software Version function, the version of the installed software can be viewed

on the display.

- UID - Select the UID function to display the identication ID for the RDM control.

• Press the LEFT button repeatedly to exit the menu.

- DMX View - Select the View DMX function to display all DMX menu.

• Press the LEFT button repeatedly to exit the menu.

17

RA3000PROFILE

3.17 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

Fig.7

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.18 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

Fig.8

Example:

5 pin XLR connector

4

RA3000PROFILE

18

3.19 DMX CONTROL

38 Ch 39 Ch 40 Ch 41 Ch 42 Ch FUNCTION

DMX

Value

1 1 1 1 1

PAN COARSE

0~100% 000 - 255

2 2 2 2 2

PAN FINE

0~100% 000 - 255

3 3 3 3 3

TILT COARSE

0~100% 000 - 255

4 4 4 4 4

TILT FINE

0~100% 000 - 255

5 5 5 5 5

P/T SPEED

Fastest to slowest

Movement with Blackout

000 - 250

251 - 255

6 6 6 6 6

SHUTTER

No function (shutter open)

Shutter eect slow to fast

No function (shutter open)

Pulse-eect in sequences

No function (shutter open)

Random Shutter eect slow to fast

No function (shutter open)

000-010

011-082

083-093

094-163

164-174

175-244

245-255

7 7 7 7 7

DIMMER 8BIT

0~100% 000 - 255

8 8 8 8 8

DIMMER 16BIT

0~100% 000 - 255

9 9 9 9 9

DIMMER FADE

Snap 0% to 100% fade out 000 - 255

10 10 10 10 10

CYAN

0~100% 000 - 255

11 11 11 11 11

MAGENTA

0~100% 000 - 255

12 12 12 12 12

YELLOW

0~100% 000 - 255

13 13 13 13 13

CTO

0~100% 000 - 255

14 14 14 14 14

COLOR

Open

Open+Deep Red

Deep Red

Deep Red+Deep blue

Deep Blue

Deep Blue+Primary green

Primary green

Primary green+Half minus green

000 - 004

005 - 009

010 - 013

014-018

019-022

023-027

028-031

032-036

La pagina sta caricando ...

ProLights RA3000PROFILE Manuale utente

ProLights RA3000PROFILE Manuale utente

in altre lingue

Documenti correlati

Altri documenti