Gigabyte GA-7NNXPV Manuale utente

When you installing AGP card, please make sure the following notice

is fully understood and practiced. If your AGP card has "AGP 4X/8X

(1.5V) notch"(show below), please make sure your AGP card is AGP

4X/8X.

Caution: AGP 2X card is not supported by nVIDIA

®

nForce

™

2 Ultra 400.

You might experience system unable to boot up normally. Please

insert an AGP Pro 4X/8X card.

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X

mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X(1.5V) mode

by adjusting the jumper. The factory default for this card is 2X(3.3V). The

GA-7N400 Pro2 / GA-7N400 / GA-7N400-L (or any AGP 4X/8X only)

motherboards might not function properly, if you install this card without

switching the jumper to 4X(1.5V) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color",

the graphics card manufacturer & some SiS 305 cards, their golden finger is

compatible with 2X(3.3V) / 4X(1.5V) mode AGP slot, but they support

2X(3.3V) only. The GA-7N400 Pro2 / GA-7N400 / GA-7N400-L (or any AGP

4X/8X only) motherboards might not function properly, If you install this card

in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage

128 Pro chip, the design of AG32S(G) is compliance with AGP 4X(1.5V)

specification. Therefore, AG32S(G) will work fine with nVIDIA

®

nForce2 Ultra

400 based motherboards.

Before you install PCI cards, please remove the Dual BIOS label from PCI

slots if there is one.

AGP 4X/8X notch

7n400Pro2_1002_f.p65 2003/7/4, ¤U¤È 03:211

The author assumes no responsibility for any errors or

omissions that may appear in this document nor does the

author make a commitment to update the information

contained herein.

Third-party brands and names are the property of their

respective owners.

Please do not remove any labels on motherboard, this may

void the warranty of this motherboard.

Due to rapid change in technology, some of the

specifications might be out of date before publication of

this booklet.

7n400Pro2_1002_f.p65 2003/7/4, ¤U¤È 03:212

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

oo

o EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment

oo

o EN 61000-3-2*

TT

T EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”

oo

o EN 55013

Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment

oo

o EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”

oo

o EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

TT

T EN 50081-1

Generic emission standard Part 1:

Residual commercial and light industry

TT

T EN 50082-1

Generic immunity standard Part 1:

Residual commercial and light industry

oo

o EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment

oo

o EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment

oo

o EN 55082-2

TT

T EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus

oo

o ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)

oo

o EN50091-2

oo

o EN 55020

oo

o DIN VDE 0855

oo

o part 10

oo

o part 12

(EC conformity marking)

TT

T CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use

oo

o EN 60950

oo

o EN 60065

Safety of household and similar

electrical appliances

oo

o EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp)

Date : June 30, 2003

TT

T EN 60555-3

Timmy Huang

oo

o EN 50091-1

Safety for information technology equipment

including electrical bussiness equipment

General and Safety requirements for

uninterruptible power systems (UPS)

Mother Board

GA-7N400 Pro2 / GA-7N400 / GA-7N400-L

7n400Pro2_1002_f.p65 2003/7/4, ¤U¤È 03:213

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name: Motherboard

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature:

Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Date:

ERIC LU

June 30, 2003

GA-7N400 Pro2 /GA-7N400 /GA-7N400-L

7n400Pro2_1002_f.p65 2003/7/4, ¤U¤È 03:214

USER'S MANUAL

GA-7N400 Pro2 / GA-7N400 / GA-7N400-L

AMD Socket A Processor Motherboard

AMD Athlon

™

/ Athlon

™

XP / Duron

™

Socket A Processor Motherboard

Rev. 1002

12ME-7N400P2-1002

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:271

- 2 -N400 Pro2 / N400 Series Motherboard

English

Table of Content

Item Checklist .........................................................................................4

Chapter 1 Introduction............................................................................5

Features Summary...................................................................................... 5

GA-7N400 Pro2 Motherboard Layout ......................................................... 8

GA-7N400 Motherboard Layout .................................................................. 9

GA-7N400-L Motherboard Layout............................................................. 10

Block Diagram - GA-7N400 Pro2 / GA-7N400 / GA-7N400-L ................. 11

Chapter 2 Hardware Installation Process.............................................13

Step 1: Set System Jumper (CLK_SW)&(CLK_RATIO)............................14

Step 2: Install the Central Processing Unit (CPU).....................................15

Step 2-1: CPU Installation..............................................................................................15

Step 2-2: CPU Cooling Fan Installation........................................................................16

Step 3: Install Memory Modules................................................................17

Step 4: Install expansion cards ................................................................. 20

Step 5: Connect ribbon cables, cabinet wires and power supply ............21

Step 5-1: I/O Back Panel Introduction...........................................................................21

Step 5-2: Connectors Introduction.................................................................................23

Chapter 3 BIOS Setup .........................................................................39

The Main Menu (For example: BIOS Ver. : E2)........................................ 40

Standard CMOS Features.........................................................................42

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:272

Table of Content

English

- 3 -

Advanced BIOS Features .......................................................................... 44

Advanced Chipset Features ......................................................................47

Integrated Peripherals .............................................................................. 49

Power Management Setup .......................................................................54

PnP/PCI Configurations.............................................................................57

PC Health Status........................................................................................58

Frequency/Voltage Control........................................................................ 60

Load Fail-Safe Defaults.............................................................................61

Load Optimized Defaults........................................................................... 62

Set Supervisor/User Password.................................................................. 63

Save & Exit Setup.......................................................................................64

Exit Without Saving ...................................................................................65

Chapter 4 Technical Reference ...........................................................67

@BIOS

™

Introduction.................................................................................67

Flash BIOS Method Introduction............................................................... 68

2- / 4- / 6-Channel Audio Function Introuction .......................................... 78

Xpress Recovery Introduction ...................................................................84

Chapter 5 Appendix.............................................................................89

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:273

- 4 -N400 Pro2 / N400 Series Motherboard

English

Item Checklist

Computer motherboards and expansion cards contain very delicate Integrated Circuit

(IC) chips. To protect them against damage from static electricity, you should follow

some precautions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have one, touch

both of your hands to a safely grounded object or to a metal object, such as the power supply

case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other

components.

4. Place components on a grounded antistatic pad or on the bag that came with the components

whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX power

connector on the motherboard.

Installing the motherboard to the chassis...

If the motherboard has mounting holes, but they don't line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful of

your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

The N400 Pro2 / N400 Series motherboard

CD for motherboard driver & utility

The N400 Pro2 / N400 Series user's manual

Quick PC Installation Guide

GigaRAID manual (j)

SATA RAID manual (j)

GC-SATA Card (optional)

(Manual; SATA cable x 1; Power cable x 1)

IDE cable x 3 / Floppy cable x 1 (j)

IDE cable x 1 / Floppy cable x 1(kl)

Serial ATA cable x 2 (j)

IEEE1394 cable x 1 (j)

2 Port USB Cable x 1

Audio Combo Kit x 1 (j)

(SURROUND-Kit + SPDIF Out Kit)

I/O Shield

Motherboard Settings Label

ATX 12V Cable (*)

(*) If this "ATX_12V connector" is not connected, system cannot boot.

j For GA-7N400 Pro2 only. k For GA-7N400 only. l For GA-7N400-L only.

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:274

Introduction

English

- 5 -

Form Factor  30.5cm x 24.4cm ATX size form factor, 4 layers PCB

Motherboard  N400 Pro2/N400 Series:

GA-7N400 Pro2 / GA-7N400 / GA-7N400-L

CPU  Socket A processor for AMD Athlon

™

/ Athlon

™

XP / Duron

™

(K7)

128K L1 & 256K/64K L2 cache on die

 400/333/266/200

MHz FSB

 Supports 1.4GHz and faster

Chipset  nVIDIA

®

nForce

™

2 Ultra 400 Memory/AGP/ PCI Controller (PAC)

 nVIDIA

®

nForce

™

2 MCP Integrated Peripheral Controller

(PSIPC)

Memory  4 184-pin DDR DIMM sockets

 Supports Dual Channel DDR400/DDR333/DDR266 DIMM

 Supports 128MB/256MB/512MB/1GB unbuffered DRAM

 Supports up to 3GB DRAM (Max)

 Supports only 2.5V DDR DIMM

I/O Control  IT8712F

Slots  1 AGP slot supports 8X/4X mode, AGP3.0 8X interface at 533MHz

 5 PCI slots support 33MHz & PCI 2.2 compliant

On-Board IDE  2 IDE controllers provides IDE HDD/CD-ROM (IDE1, IDE2) with

PIO, Bus Master (Ultra DMA33/ATA66/ATA100/ATA133) operation

modes

 IDE3

(

j

)

and IDE4

(

j

)

compatible with RAID,

Ultra ATA133/100, IDE

Serial ATA

(

j

)

 2 Serial ATA connectors in 150 MB/s operation mode

(

j

)

 Controlled by SiI3112

(

j

)

Hardware Monitor  CPU/System/Power

(

j

)

fan revolution detect

 CPU/System temperature detect

 CPU warning temperature

 System voltage detect

 CPU/System/Power

(

j

)

fan fail warning

 CPU Smart Fan control

(

j

)

 Thermal shutdown function

to be continued......

Chapter 1 Introduction

Features Summary

j For GA-7N400 Pro2 only. k For GA-7N400 only. l For GA-7N400-L only.

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:275

- 6 -N400 Pro2 / N400 Series Motherboard

English

On-Board Peripherals  1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes

 1 Parallel port supports Normal/EPP/ECP mode

 2 Serial ports (COM1 & COM2)

 6 USB 2.0/1.1 ports (4 x Rear, 2 x Front by cable)

 3 IEEE1394 ports (by cable)

(

j

)

 1 IrDA connector for IR

 1 Front Audio connector

On-Board LAN  Builit in Realtek 8110S Gigabit

(

j

)

 Builit in Realtek 8100C

(

l

)

 1 RJ45 port

On-Board Sound  Realtek ALC650 CODEC

 Line Out / 2 front speaker

 Line In / 2 rear speaker (by s/w switch)

 Mic In / center & subwoofer (by s/w switch)

 SPDIF In / Out

 CD In / AUX In / Game port

On-Board IDE RAID

(

j

)

 Onboard GigaRAID IT8212F chipset

 Supports data striping (RAID 0) or mirroring (RAID 1) or

striping+mirroring (RAID 0 + RAID 1)

 Supports JBOD function

 Supports concurrent dual ATA133 IDE controller operation

 Support ATAPI mode for HDD

 Supports IDE bus master operation

 Support ATA133/RAID mode switch by BIOS

 Displays status and error checking messages during boot-up

 Mirroring supports automatic background rebuilds

 Features LBA and Extended Interrupt 13 drive translation in

controller onboard BIOS

to be continued......

j For GA-7N400 Pro 2 only. k For GA-7N400 only. l For GA-7N400-L only.

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:276

Introduction

English

- 7 -

On-Board SATA RAID

(

j

)

 Onboard Silicon Image SiI3112

 Supports Disk striping (RAID0) or DISK Mirroring (RAID1)

 Supports UDMA up to 150 MB/sec

 AIL UDMA and PIO Modes

 Up to 2 SATA Device

 ACPI and ATA/ATAPI6

 Supports hot plug function

On-Board IEEE1394

(

j

)

 Built-in TI TSB43AB23

PS/2 Connector  PS/2 Keyboard interface and PS/2 Mouse interface

BIOS  Licensed AWARD BIOS

 Supports Dual BIOS

(

j

)

 Supports Face Wizard

 Supports Q-Flash

Additional Features  PS/2 Keyboard power on by password

 PS/2 Mouse power on

 External Modem wake up

 STR(Suspend-To-RAM)

 AC Recovery

 Poly fuse for keyboard over-current protection

 USB KB/Mouse wake up from S3

 Supports Thermal Shutdown function

 Supports @BIOS

Overclocking  Over Voltage (CPU/DDR/AGP) by BIOS

 Over Clock (CPU/DDR/AGP/PCI) by BIOS

Please set the CPU host frequency in accordance with your processor's specifications.

We don't recommend you to set the system bus frequency over the CPU's specification because

these specific bus frequencies are not the standard specifications for CPU, chipset and most of the

peripherals. Whether your system can run under these specific bus frequencies properly will

depend on your hardware configurations, including CPU, Chipsets, SDRAM, Cards…etc.

j For GA-7N400 Pro2 only. k For GA-7N400 only. l For GA-7N400-L only.

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:277

- 8 -N400 Pro2 / N400 Series Motherboard

English

CD_IN

GA-7N400 Pro2

KB_MS

COM A

LPT

USB

LAN

ATX_12V

SOCKET A

CPU_FAN

IDE1

IDE2

DDR2

COM B

PWR_LED

BAT

PCI1

PCI2

PCI3

F_USB

IT8712F

MAIN

BIOS

CODEC

nVIDIA

®

nForce

™

2

MCP

DDR3

PCI4

PCI5

GAME

F_AUDIO

AUX_IN

IR

IDE3

GigaRAID

IT8212

BACKUP

BIOS

SiI3112

SATA0

DDR4

RAM_LED

ATX

SYS_FAN

CI

NB_FAN

IDE4

DDR1

SPDIF_IO

SUR_CEN

2X_DET

AUDIO

F_PANEL

F1_1394

Dual Channel DDR

INFO_LINK

AGP

nVIDIA

®

nForce

™

2

Ultra 400

USB

FDD

CLK_SW

SATA1

RTL8110S

TSB43AB23

F2_1394

CLK_RATIO

PWR_FAN

GA-7N400 Pro2 Motherboard Layout

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:278

Introduction

English

- 9 -

GA-7N400 Motherboard Layout

CD_IN

GA-7N400

KB_MS

COM A

LPT

USB

ATX_12V

SOCKET A

CPU_FAN

IDE1

IDE2

DDR2

COM B

PWR_LED

BAT

PCI1

PCI2

PCI3

F_USB

IT8712F

MAIN

BIOS

CODEC

nVIDIA

®

nForce

™

2

MCP

DDR3

PCI4

PCI5

GAME

F_AUDIO

AUX_IN

IR

DDR4

RAM_LED

ATX

SYS_FAN

CI

DDR1

SPDIF_IO

SUR_CEN

2X_DET

AUDIO

F_PANEL

Dual Channel DDR

INFO_LINK

AGP

nVIDIA

®

nForce

™

2

Ultra 400

USB

FDD

CLK_SW

CLK_RATIO

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:279

- 10 -N400 Pro2 / N400 Series Motherboard

English

CD_IN

GA-7N400-L

KB_MS

COM A

LPT

USB

LAN

ATX_12V

SOCKET A

CPU_FAN

IDE1

IDE2

DDR2

COM B

PWR_LED

BAT

PCI1

PCI2

PCI3

F_USB

IT8712F

MAIN

BIOS

CODEC

nVIDIA

®

nForce

™

2

MCP

DDR3

PCI4

PCI5

GAME

F_AUDIO

AUX_IN

IR

DDR4

RAM_LED

ATX

SYS_FAN

CI

DDR1

SPDIF_IO

SUR_CEN

2X_DET

AUDIO

F_PANEL

Dual Channel DDR

INFO_LINK

AGP

nVIDIA

®

nForce

™

2

Ultra 400

USB

FDD

CLK_SW

RTL8100C

CLK_RATIO

GA-7N400-L Motherboard Layout

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2710

Introduction

English

- 11 -

nVIDIA

®

nForce

™

2

Ultra 400

CPUCLK+/- (100/133/166/200MHz)

System Bus

400/333/266/200MHz

12 MHz

14.318 MHz

AGP

4X/8X

AGPCLK

(66MHz)

5 PCI

PCICLK

(33MHz)

AC97 Link

MIC

LINE-IN

LINE-OUT

AMD-K7

™

CPU

AC97

CODEC

IDE3j

SiI3112j

2 Serial

ATAj

IDE4j

GigaRAID

IT8212j

400/333/266/200MHz

DDR RAM

nVIDIA

®

nForce

™

2

MCP

RJ45

RTL8110Sj

RTL8100Cl

LPC BUS

6 USB

Ports

ATA33/66/100/133

IDE Channels

IT8712

24 MHz

33 MHz

Game Port

Floppy

LPT Port

PS/2 KB/Mouse

2 COM Ports

BIOS

3 IEEE1394j

TI j

TSB43AB23

IR

Block Diagram - GA-7N400 Pro2 / GA-7N400 / GA-7N400-L

j For GA-7N400 Pro2 only. k For GA-7N400 only. l For GA-7N400-L only.

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2711

- 12 -N400 Pro2 / N400 Series Motherboard

English

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2712

Hardware Installation Process

English

- 13 -

To set up your computer, you must complete the following steps:

Step 1- Set system jumper (CLK_SW)& (CLK_RATIO)

Step 2- Install the Central Processing Unit (CPU)

Step 3- Install memory modules

Step 4- Install expansion cards

Step 5- Connect ribbon cables, cabinet wires, and power supply

Chapter 2 Hardware Installation Process

Step 3

Step 4

Step 5

Step 2

Step 5

Congratulations! You have accomplished the hardware installation!

Turn on the power supply or connect the power cable to the power outlet. Continue with the

BIOS/software installation.

Step 1

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2713

- 14 -N400 Pro2 / N400 Series Motherboard

English

Step 1: Set System Jumper (CLK_SW) & (CLK_RATIO)

The clock ratio can be switched by CLK_RATIO and refer to below table.The system bus frequency can

be switched at 100MHz and auto by adjusting CLK_SW.

Default Setting :

Auto (X X X X X X)

MNote: In order to BIOS can auto detecting when

your CPU mutiplier over 18x, please adjust mutiplier

swich in CLK_RATIO to "AUTO."

RATIO 1 2 3 4 5 6

AUTO X X X X X X

(Default)

5x OOX O OO

5.5x X O X O O O

6x O X X O O O

6.5x X X X O O O

7x OOO X OO

7.5x X O O X O O

8x O X O X O O

8.5x X X O X O O

9x OOX X OO

9.5x X O X X O O

10x O X X X O O

10.5x X X X X O O

11x OOO O OO

11.5x X O O O O O

12x O X O O O O

12.5x X X O O O O

13x O O X O X O

13.5x X O X O X O

14x O X X O X O

15x O O O X X O

16x O X O X X O

16.5x X X O X X O

17x O O X X X O

18x X O X X X O

O: ON / X :OFF

CLK_RATIO

You must set CLK_SW to 100MHz

when you used FSB 200MHz CPU.

CLK_SW

ON AUTO

OFF 100MHz

AUTO : Supports FSB 400/333/266 MHz CPU

100MHz : Fix FSB 200MHz CPU

CLK_SW

Default Setting : OFF

OFF

ON

5

ON

234

CLK_RATIO

6

1

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2714

Hardware Installation Process

English

- 15 -

Before installing the processor, adhere to the following warning:

1.Please make sure the CPU type is supported by the motherboard.

2.If you do not match the CPU socket Pin 1 and CPU cut edge well, it will

cause improper installation. Please change the insert orientation.

CPU Top View CPU Bottom View

Socket Actuation Lever

1 Pull up the CPU socket lever and

up to 90-degree angle.

Pin1 indicator

2. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

Step 2: Install the Central Processing Unit (CPU)

Step 2-1: CPU Installation

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2715

- 16 -N400 Pro2 / N400 Series Motherboard

English

Step 2-2: CPU Cooling Fan Installation

Before installing the CPU cooling fan, adhere to the following warning:

1.Please use AMD approved cooling fan.

2.We recommend you to apply the thermal tape to provide better heat

conduction between your CPU and cooling fan.

3.Make sure the CPU fan power cable is plugged in to the CPU fan

connector, this completes the installation.

Please refer to CPU cooling fan user's manual for more detail

installation procedure.

3. Fasten the cooling fan supporting-

base onto the CPU socket on the

motherboard.

2. Use qualified fan approved by AMD.

4. Make sure the CPU fan is plugged

to the CPU fan connector, than

install complete.

1. Press down the CPU socket lever

and finish CPU installation.

7n400pro2_1002_q.p65 2003/7/4, ¤U¤È 03:2716

La pagina sta caricando ...

Gigabyte GA-7NNXPV Manuale utente

Questo manuale è adatto anche per

Gigabyte GA-7NNXPV Manuale utente

in altre lingue

Documenti correlati

Altri documenti