Christie LX1750 Manuale utente

LX1750

PJ Network Guide

020-000640-01

PJ Network Manager for Windows

SNMP Manager Software

This is the manual for the PJ Network Manager software.

This software is Windows-compliant, but non-Mac-compliant.

Read this manual thoroughly to operate the PJ Network Manager software.

First, read the user manual of the projector to understand the basic opera-

tion of the projector and the safety instructions.

The safety instructions in the user manual should be followed strictly.

TQBJ0657

ENGLISH

User Manual

020-000640-01 Rev.1 (11-2013)

2

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Contents ..................................................................................2

Chapter 1 Introducing ..........................................................3

Introducing ......................................................................................................................................................3

SNMP ...................................................................................................................................................................3

Trademarks .......................................................................................................................................................3

Operating Environment ...........................................................................................................................4

Chapter 2 Set up ....................................................................5

PJ Network Manager installation ........................................................................................................6

PJ Network Manager un-installation ................................................................................................6

Chapter 3 Basic Operation ...................................................7

Launching and quitting PJ Network Manager ...........................................................................8

Name of status window ...........................................................................................................................8

Quitting PJ Network Manager ..............................................................................................................9

Menu tree .........................................................................................................................................................9

What's Target ..................................................................................................................................................9

Name of the button on the tool bar .............................................................................................10

Icon display for the target....................................................................................................................10

Addition of the target ............................................................................................................................11

Editing the target ......................................................................................................................................11

Deletion of the target .............................................................................................................................11

Setting up the warning value ...........................................................................................................12

Starting target monitoring ..................................................................................................................12

What happens when an abnormality or connection error happens? .....................13

What happens when a predefined event occurs on the target equipment? .....13

What is a Trap? ............................................................................................................................................13

Stopping monitoring the target ......................................................................................................14

Displaying all the status information of the target ..............................................................14

Setting the target group ......................................................................................................................14

Setting the password of Telnet .........................................................................................................15

Setting commands batch processing for multiple targets .............................................15

Setting timer for targets ........................................................................................................................16

Setting default information ................................................................................................................17

Customizing the status list ..................................................................................................................19

Viewing the alert information ...........................................................................................................22

Viewing the event log ............................................................................................................................23

Description of Event, Type, Warning column, Warning value ......................................24

About event treatment .........................................................................................................................26

Viewing the command history .........................................................................................................27

Storing the management file ............................................................................................................28

Information saved to the registry ..................................................................................................28

Registering the target information from the defined file at once ..............................29

Format of the defined file ....................................................................................................................30

Example of the defined file .................................................................................................................30

Login to the target equipment ........................................................................................................31

Contents

3

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Introducing

This PJ Network Manager is a SNMP manager software for the network equipment which

supports the private MIB (Management Information Base).

By installing the PJ Network Manager to the computer, you can monitor the equipment

such as the projector, the projection monitor and the flat display monitor connected to the

network.

* The PJ Network Manager can handle our products which has a SNMP agent function.

SNMP

SNMP is an abbreviation for Simple Network Management Protocol.

On the TCP/IP network, it is the protocol to monitor and control the equipment connected

to the network.

SNMP realizes the management function by reading and changing the management infor-

mation called MIB with SNMP protocol between the manager (management equipment)

and agent (controlled equipment) which are connected with TCP/IP network.

Trademarks

Microsoft, Windows, Windows 2000, Windows XP, Windows Vista, and Windows 7 are regis-

tered trademarks of Microsoft Corporation. Macintosh is a registered trademark of Apple,

Inc. in the USA and other countries. Other products or brand names in this manual are reg-

istered trademarks or trademarks of their respective owners.

* Unauthorized use of a part or whole of the contents in this manual is prohibited.

* The contents of this manual are subject to change without notice.

PJ1

PC6

PC4

PJ2

PJ3

PC5

SNMP Manager

Trap

You received

a trap.

PJ4

Chapter 1 Introducing

4

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Operating Environment

Limited condition

The number of agents monitored is up to 200.

Chapter 1 Introducing

Expression/Abbreviation

The OS of the computer and the Web browser described in this manual is Windows 7

Professional and Internet Explorer 9.0. In case of another OS or Web browser, some instruc-

tion procedures may differ from the actual operation depending on your computer envi-

ronment.

Use of this manual

This manual does not provide the description of basic operation and functions for the

computer, web browser, projector and network. For instructions about each piece of

equipment or application software, please refer to the respective manual.

Item Minimum Recommended

CPU Pentium III 400MHz or higher

Pentium 4 2.0GHz or higher for Windows XP

Pentium 4 3.0GHz or higher for Windows Vista

and Windows 7

Memory 128MB or higher

256MB or higher for Windows XP

1GB or higher for Windows Vista and Windows 7

HDD More than 20MB of free disk space

Screen

resolution

SVGA (16 colors or more) XGA True color or more

LAN 10Mbps or more 100Mbps or more

OS

Windows 2000

Windows XP

Windows Vista

Windows 7

Windows XP Professional

Windows Vista (32bit version)

Windows 7 (32bit version)

5

Chapter 2

Set up

2

020-000640-01 Rev.1 (11-2013)

6

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 2 Set up

PJ Network Manager installation

1 Set the supplied CD-ROM into the CD-ROM drive of

your computer. Double click

SetupTool.exe icon in

the "PJ Network Manager" folder of the CD-ROM.

2 Select "[English [United States]" from the pull-

down menu on the "Choose Setup Language" win-

dow and click OK to start installing and then follow

the installation wizards.

When the "Software License Agreement" appears,

read contents carefully and click Yes if you agree

with the license agreement to proceed with install-

ing.

Note:

To install the software on the computer with Windows 2000, Windows XP, Windows

Vista, or Windows 7 you should logon as administrator. Before installation, make sure

that other applications are closed, otherwise proper installation cannot be made.

PJ Network Manager un-installation

To remove the PJ Network Manager software from your computer, use "Add & Remove

Programs" on the control panel. (In case of Windows Vista or Windows 7, use "Programs

and Features" from the control panel.)

7

Chapter 3

Basic Operation

3

020-000640-01 Rev.1 (11-2013)

8

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 3 Basic Operation

Launching and quitting PJ Network Manager

To launch PJ Network Manager, do one of the following.

- Select "PJ Network Manager" from the menu "Start" - "All programs".

- Double click a management file*

1

.

Tool bar

Menu

Status list

Status bar Polling times indication

Event indication

Items Description

Menu .....................................Executes a command with menu selection.

Tool bar ............................... Executes a command assigned to a button.

Target ...................................Network equipment for monitoring.

Status bar ........................... Indicates the status of PJ Network Manager and explaining the command selected

with cursor.

Status list ............................ Indicates the status of targets monitoring.

When some errors are detected, the target name, icon and error items are indicated

with red.

Status column ................ Column of status list.

Polling times indication .........Indicates the times of polling during the monitoring.

Event indication ............Indicates the event (ALERT, TRAP, SYSERR) when the event happened.

Name of status window

Status column

*1 The file in which the Monitor target information and event log information are stored. Refer to item

"Storing the management file" (+p.28) for further details.

* Double clicking the target name launches the web browser and displays

the login window of the target. (+p.31)

Target

9

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Quitting PJ Network Manager

To quit the PJ Network Manager, click the close box on top right of the status window, or

select "Exit" from the "File" menu.

[Note]

* The PJ Network Manager cannot open multiple status windows at the same time.

Menu tree

Menu Sub menu Operation

File New Creates a new management file.

Open Opens an existing management file.

Save Saves the active management file.

Save As Saves the active management file with a new file name.

Exit Quits the application.

Target Target monitoring Starts or stops target monitoring.

Target addition Adds a new target. Target information window will appear.

Target editing Edits selected target information.

Target deletion Deletes the selected target.

Group setting Groups the selected targets.

Warning value setting Sets up the warning value of the selected target.

Telnet setting Sets up the password of telnet.

Commands batch processing Sets commands batch processing for multiple selected targets.

Timer setting Sets up the timer for the selected target.

System Target batch registration

Imports target information defined with the external file.

System default setting Sets up the default setting (monitoring information, e-mail informa-

tion).

Column selection Selects display items on the status list.

Font setting Sets up display font type and size on the status list.

Display Update Updates the information on the status list display.

Target display Displays selected target information.

Alert display Displays all of alert information on the status list.

Event log display Displays all the event logs.

Command history display

Displays all of the command history.

Tool bar Switches the tool bar on or off.

Help Version information Displays version of software.

What's Target

Target indicates the network equipment which provides an SNMP agent function.

10

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 3 Basic Operation

Name of the button on the tool bar

The following commands are assigned to the buttons on the tool bar.

Button Operation

New ..................................................Creates a new management file.

Open ............................................... Opens an existing management file.

Save ................................................. Saves the active management file.

Target monitoring ................. Starts or stops target monitoring.

Target display ........................... Displays selected target information.

Alert display ............................... Displays all of alert information on the status list.

Event log display .................... Displays all the event logs.

Command history display

.. Displays all of the command history.

0 To switch the tool bar display on or off, select "Tool bar" from "Display" menu.

New Save Target display Event log display

Target monitoring

Start/Stop

Open

Alert display

Icon display for the target

Displays icon according to the target condition.

Icon

Condition

Flat display type Projector type

Normal

Abnormal condition (One of the abnormalities, Alert, Trap or System

error is happening on the target.)

Connection error (Target has been disconnected from the network)

Acquisition error (Target has been disconnected from the network, or

does not provide SNMP function.)

Unknown (Target monitoring is not operating)

Command history display

11

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Addition of the target

1 Select Target Addition from Target menu. The target

information registering window appears.

2 Enter target setup information and click Update. The

information set on the target equipment is displayed on

the system information items.

0 When the target equipment is not operating, or it is not the

monitoring equipment, the error dialog "Cannot obtain infor-

mation" will appear.

3 Click OK to close the window. Repeat the above steps to register for other equipment

which is to be managed.

Editing the target

1 To select a target name to edit on the status list, right-click.

2 Select Target editing on the popup menu. In the target information window, edit the

contents, then click OK.

0 The system information cannot be edited.

0 Target editing can be executed by selecting Target editing from Target menu.

Deletion of the target

1 Select a target name to delete on the status list with right-click.

2 Select Target deletion on the popup menu. In the confirmation dialog, click Yes to

delete.

0 Target deletion can be executed by selecting Target deletion from Target menu.

0 It cannot perform the target addition, editing and deletion during the target monitoring.

0 Up to 200 targets can be registered.

0 Up to 255 characters can be used for target name and community.

Items Description

Name ......................... Enter a management name of the target

equipment.

IP address ............... Enter IP address of the target equipment.

Community ........... Enter a community name in the network.

Default name is "public".

System information ..... Displays information set on the network

equipment

Addition of the target

12

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 3 Basic Operation

Setting up the warning value

PJ Network Manager provides a function to display

the alert when the use time of the setting item

reaches a specified setting time. The available set-

ting items (use time) depend on the target equip-

ment.

1

Select a target on the status list with right-click.

0 When setting multiple targets together, select tar-

gets by pressing "Shift" or "Control" key.

2 Select Warning value setting on the popup

menu. The setting window will appear as the

right figure.

3 Check Warning time check box. The setting

items are activated. Select a setting item and click

Edit. Another setting window appears.

4 Enter the threshold value of selected item and

then click OK. The setting window will disappear.

5 Set up a warning value for remaining items if avail-

able and then click OK. The setting window will

disappear.

0 To disable the warning value, clear Warning time

check box.

0 When selecting multiple targets, the value set to the lowest target on the status list is displayed as

the current setting time. Up to 99,999 hours can be set for the use time. The warning value is stored

in the management file.

Starting target monitoring

1 Click

on the tool bar to start monitoring the target.

2 PJ Network Manager starts polling the target in sequence from the top of the status list

and displays the results on the status list.

(Example of the set up window)

13

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

What is a Trap?

Trap is the event predefined by the SNMP agent. If the predefined event ( "When PJ lamp is

off", "When internal PJ power circuit is failed" etc. ) happens, the target sends trap informa-

tion to the SNMP manager.

When happens the alert on the target

What happens when an abnormality or connection error happens?

If an abnormality or connection error happens on the target, PJ Network Manager indicates

target name, icon and status column item with red color to let you know the abnormality.

0 When PJ Network Manager cannot acquire the MIB information of the target equipment, it indi-

cates as Connection Error.

0 The interval of target monitoring is according to the setting of Monitoring interval on System

default setting from System menu.

(+p.17)

0 For the way to give notice of the alert information, refer to Event reception process on System

default setting from System menu.

(+p.17)

What happens when a predefined event occurs on the target

equipment?

During the target monitoring, if the predefined event (trap) happens on the target equip-

ment, the target sends the trap information to PJ Network Manager. This trap information is

displayed on the status list.

The trap information is set up in the SNMP setting items of the target equipment. Projector

has items such as "When PJ lamp is off", "When the life span of lamp is reached", "When

internal PJ power circuit is failed" etc. For further trap information, refer to "SNMP setting" in

the separated network user manual.

0 For the way to give notice of the trap information, refer to Event reception process on System

default setting from System menu.

(+p.17)

14

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 3 Basic Operation

Displaying all the status information of the target

Select a target and click on the tool bar. The following status window appears and dis-

plays all the available status information of the target.

0 The target name and item which have an

abnormality or connection error happen-

ing are indicated with red.

0 When PJ Network Manager cannot

acquire the value of column information,

"---" is displayed.

Stopping monitoring the target

To stop monitoring the target, click again on the tool bar.

0 Projectors with different network passwords cannot be set to the same group. It is necessary

for the projectors in the same group to have the same password.

0 The above procedure can be performed by selecting Target display from Display menu.

Setting the target group

The target group can be set up by the procedure below. After targets have been grouped,

you can set commands for multiple targets in the same group by batch processing.

1 Select targets which you want to set from the status list. Select Group setting from

Target menu, the dialog box will appear as in the figure below.

2 Select a group, and then click OK.

0 "---" will not set the group.

15

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Setting the password of Telnet

The telnet password can be set by the procedure below. It is necessary to make the pass-

word the same as the network password.

1 Select a target which you want to set as the telnet password from the status list. You can

select multiple targets.

2 Select Telnet setting from the Target menu. The Telnet setting dialog appears as shown

below. Set a password and click OK. When multiple targets are selected, all the selected

targets are set as the same password.

Setting up the password of Telnet

0 The initial setting is "0000".

Setting commands batch processing for multiple targets

The commands for batch processing of multiple targets can be set following the proce-

dure below.

1 Select a target belonging to the batch processing group which you want to set, and

select Commands batch processing from Target menu. Commands batch processing

dialog box will appear as shown below.

2 Select a command which you want to set, and click Edit. Parameter editing dialog box

will appear. Select a parameter, and then click OK. The check box of Commands batch

processing dialog box will be checked.

3 Click OK. The commands are carried out to all the targets of the same group.

0 The commands also work for the target which is not set to a group.

16

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 3 Basic Operation

Commands batch processing : Available Command

Items Description

Power ON/OFF ......................... Sets the Power ON or Power OFF.

Input,Source

.............................. Sets the Input and Source. Selects Input and Source.

Screen ....................................... Sets the screen size. Resizes the picture screen.

Background

............................... Sets the background. Selects the background screen for when no input signal is

detected.

Display

........................................ Sets the Display. Decides whether to display On-Screen Displays or not.

Shutter(No show)

.................... Sets the Shutter (No show). Sets black out the image.

Lamp control

............................. Sets the Lamp control. Changes brightness of the screen.

Fan control ................................. Sets the Fan control. Chooses the running speed of cooling fans.

Setting timer for targets

The timer information for targets can be set by the procedure below.

1 Choose a target for which you want to set the timer.

2 Select Timer setting from Target menu. Timer selection dialog box will appear as

shown below. Select a checkbox for an event you want to enable/add.

3 When you want to add events, click Add. Input timer information in the Timer setting

dialog box, and click OK.

4 Click OK of Timer selection dialog box, timers are set to the selected target. When

selecting multiple targets, timers are set to all the selected targets.

Timer

Items Description

Execution date ......................... Sets the Timer execution date. (every day or a day)

Execution time

.......................... Sets the Timer execution time. (hh:mm:ss)

Action ....................................... Sets the events.

17

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Setting default information

The monitoring and e-mail information can be set using the procedure below.

1 Select System default setting from System menu. The setting window will appear.

2 Switch by clicking Monitoring information or E-mail information tab for each setting.

Monitoring information

Items Description

Monitoring interval ................ Sets the interval of the polling in minute unit. (1 to 99 minutes can be set)

Temperature unit

..................... Sets the display temperature unit Centigrade or Fahrenheit.

Event reception process.......... Sets the treatment when the event (ALERT, TRAP, SYSERR) happens on the target.

For further information, refer to the item "About event treatment" (+p.26).

p Sound warning alarm

p Send e-mail

p Display warning dialog

Monitoring information

Setting up default setting

18

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Chapter 3 Basic Operation

E-mail information

Items Description

SMTP server ..................... Sets the IP address of the SMTP mail server or server host name.

Administrator's

mail address

...................... Set the e-mail address of the administrator.

Destination mail

address ................................ Sets the destination mail address when the event (ALERT, TRAP, SYSERR) happens on

the target. The mail address entering window appears when clicking Add.

E-mail information

0 If Send e-mail check box of Event reception process on Monitoring information is unchecked,

the alert e-mail will not be sent even if you set up the e-mail address.

0 Up to 10 addresses can be set up for the destination mail address.

0 For the contents of the mail, refer to item "About event treatment" (+p.26).

19

PJ Network Manager for Windows

020-000640-01 Rev.1 (11-2013)

Customizing the status list

Changing the status column indication

1 Select Column selection from System menu. The col-

umn selection window will appear.

2 On the window, check the column name to be indi-

cated on the status list.

0 The mark [*] next to the column name indicates an alert

item.

3 To change the order of the display column on the

status list, select a column you intend to change the

order and click To up or To down.

4 Click OK to close setting.

0

When specifying the column width by numeric value, enter

number (0 to 9999) onto "Column width" text box.

Column Description

*Target name ............................Name of the network equipment

*Group ...........................................Group name

*Connect ......................................Status of connection to the network (Connected, Un-connected)

*Drive time .................................Accumulated use time of the equipment

*Power status ............................ Power status of the equipment (Normal(Power-on), Normal(Standby), Power

Management, Power failure, lamp failure, etc.)

*Input status ..............................Input signal status (Signal, No signal, Signal interrupted)

*Inside Temperature

A status ....................................Status of inside temperature A (Normal, Warning, Error)

*Inside Temperature

B status ....................................Status of inside temperature B (Normal, Warning, Error)

*Inside Temperature

C status ....................................Status of inside temperature C (Normal, Error)

*External Temperature

status.........................................Status of external temperature (Normal, Warning, Error)

*Lamp1 status ..........................Status of Lamp1 (Off, On, Error, Replace)

*Lamp2 status ..........................Status of Lamp2 (Off, On, Error, Replace)

*Lamp3 status ..........................Status of Lamp3 (Off, On, Error, Replace)

*Lamp4 status ..........................Status of Lamp4 (Off, On, Error, Replace)

*Lamp1 time..............................Used time of Lamp1

*Lamp2 time..............................Used time of Lamp2

*Lamp3 time..............................Used time of Lamp3

*Lamp4 time..............................Used time of Lamp4

*Filter status ...............................Status of airfilter (Normal, Clogged)

*Option Box

filter status ............................Status of option box filter (Normal, Error, Clogged)

*Filter time ..................................Use time of airfilter

*Option Box

filter time ................................Use time of option box filter

0

The values in parentheses are typical value and they differ depending on the connected equipment.

0 The [*] next to the column name indicates alert items.

Customizing the status list

Specifies col-

umn width

La pagina sta caricando ...

Christie LX1750 Manuale utente

Christie LX1750 Manuale utente

in altre lingue

Documenti correlati

Altri documenti