Tyan S5376 Manuale utente

1

Tempest i5100W

///

S5376

Version 1.0

Copyright

manual may be reproduced or translated without prior written consent from TYAN

Computer Corp.

Trademark

All registered and unregistered trademarks and company names contained in this

manual are property of their respective owners including, but not limited to the

following.

TYAN, Tempest i5100W are trademarks of TYAN Computer Corporation.

Intel® 5100/5200/5400 Series and combinations thereof are trademarks of Intel

Corporation.

AMI, AMI BIOS are trademarks of AMI Technologies.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE is a trademark of Novell.

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Notice

Information contained in this document is furnished by TYAN Computer Corporation

and has been reviewed for accuracy and reliability prior to printing. TYAN assumes

no liability whatsoever, and disclaims any express or implied warranty, relating to

sale and/or use of TYAN products including liability or warranties relating to fitness

for a particular purpose or merchantability. TYAN retains the right to make changes

to product descriptions and/or specifications at any time, without notice. In no event

will TYAN be held liable for any direct or indirect, incidental or consequential

damage, loss of use, loss of data or other malady resulting from errors or

inaccuracies of information contained in this document.

2

Table of Contents

Check the box contents! 3

Chapter 1: Introduction

1.1 Congratulations 5

1.2 Hardware Specifications 5

Chapter 2: Board Installation

2.1 Board Image 8

2.2 Block Diagram 9

2.3 Board Parts, Jumpers and Connectors 10

2.4 Tips on Installing Motherboard in Chassis 18

2.5 Installing the Processor(s) 19

2.6 Installing the Memory 22

2.7 Attaching Drive Cables 24

2.8 Installing Add-in Cards 25

2.9 Installing Optional SO-DIMM Modules 26

2.10 Connecting External Devices 27

2.11 Installing the Power Supply 28

2.12 Finishing up 28

Chapter 3: BIOS Setup

3.1 About the BIOS 29

3.2 BIOS Menu Bar 29

3.3 Setup Basics 30

3.4 Getting Help 30

3.5 In Case of Problems 30

3.6 BIOS Main Menu 31

3.7 Advanced Menu 32

3.8 PCI PnP Menu 52

3.9 Boot Menu 54

3.10 Security Menu 58

3.11 Chipset Menu 59

3.12 Exit Menu 63

Chapter 4: Diagnostics

4.1 Beep Codes 65

4.2 Flash Utility 65

4.3 AMI BIOS Post Code 66

Appendix: SMDC Information

69

Glossary

71

Technical Support

77

3

Check the box contents!

1x S5376 motherboard

3 x Serial ATA power cable

1 x Ultra-DMA-133/100/66/33 IDE cable

2 x mini SAS Cable (S5376WAG2NR and S5376WAG2NR5)

6 x Serial ATA Cable

2 x USB2.0 cable

1x Serial Port Cable

1 x S5376 user’s manual

1 x S5376 Quick Reference guide

1 x TYAN driver CD

1 x I/O shield

2 x CPU Back Plane

1x ibutton (optional purchase, BTO, S5376WAG2NR5)

If any of these items are missing, please contact your vendor/dealer for

replacement before continuing with the installation process.

4

NOTE

5

Chapter 1: Introduction

1.1 - Congratulations

You have purchased one of the most powerful server solutions. The Tempest

i5100W (S5376) is a flexible Intel

®

platform for multiple applications, based on Intel

®

San Clemente MCH and ICH9R chipsets.

Designed to support two Intel

®

5100/5200/5400 Series processors and 48GB

DDR2-533/667 DIMM memory, and featured with integrated Dual 82573V LAN

controllers, built-in 32MB XGI Z9S video plus six SATA2 ports, the S5376 offers

exceptional performance and versatile solution for your server / Workstation.

Remember to visit TYAN’s Website at http://www.TYAN.com

. There you can find

information on all of TYAN’s products with FAQs, online manuals and BIOS

upgrades.

1.2 - Hardware Specifications

Processors

•Dual LGA771 sockets

•Supports up to two (2) Intel

®

5100/5200/5400 Series

processors

•1.33 / 1.06 GHz FSB

•VRD 11.0

Chipset

•Intel

®

San Clemente MCH

•ICH9R South Bridge

•Winbond 83627DHG Super I/O

chip

Expansion Slots

•One (1) PCI-E x16 slot w/ x16

signal from San Clemente

•Two (2) PCI-E x8 slots w/ x4

signal from San Clemente

•Three (3) 32/33 PCI 2.2 slots

•Total six (6) expansion slots

Back Panel I/O Ports

•Stacked PS/2 Mouse & Keyboard

ports

•Stacked two (2) USB 2.0 ports

•One (1) 9-pin COM port

•One (1) 15-pin VGA port

•Two (2) RJ45 10/100/1000 ports

with activity LED

•One (1) RJ45 10/100 port for SMDC

Integrated SATA Controller

(ICH9R)

•Supports six (6) SATA2 ports

running at 3.0Gb/s

•RAID 0/1/5/10 capable (Windows

OS only)

Integrated Video Controller

•XGI Z9S

•32MB DDR2 frame buffer memory

Integrated LAN Controllers

•Two 82573 (via PCI-E x1 signal)

6

Memory

•Six (6) 240-pin DDR2 DIMM

sockets

•Supports Registered ECC DIMMs

•Max. 48GB of DDR2-533/667

Optional Modules

•Optional TYAN M3295-2/M3296

SMDC support

System Management

•Winbond W83793G Hardware

Monitor ASIC

•CPU thermal & voltage monitor

support

•2-pin chassis intrusion header

•Two (2) 4-pin CPU fan headers

with tachometer monitoring and

smart FAN control

•Three (3) 4-pin system fan

headers with tachometer

monitoring, and support smart

FAN control

Integrated I/O

•Six (6) SATA (3Gb/s) ports

•Six (6) USB 2.0 ports (two at rear,

and four via headers)

•One (1) IDE connector from

Cypress CY7C68300C

•Two (2) COM ports (1 at rear, 1

via cable)

•Tyan 2x9 front panel pin header

•Tyan 2x6 front panel pin header

for LAN LED and ID LED/Switch

•2x7 pin Fan header

•One (1) SO-DIMM connector for

Tyan optional SMDC M3295-2 /

M3296

Form Factor

•CEB footprint (10.5” x 12”)

Integrated Audio (S5376WAG2NR

and S5376WAG2NR5)

•HD Audio (High-Definition Audio)

supported

•Realtek ALC262 (High-Definition

Audio) controller

•Front panel audio header (2x5 pin)

Integrated SAS Controller

(S5376WAG2NR and

S5376WAG2NR5)

•8 SAS ports from LSI 1068E (2 mini

SAS connectors)

• Without ibutton: RAID 0/1/10

supported (LSI IR RAID,

S5376WAG2NR only)

• With ibutton: RAID 0/1/10/5

supported (LSI Mega RAID,

S5376WAG2NR5 only)

NOTE: S5376WAG2NR5 is BTO sku.

Please contact your local dealer for

purchase.

BIOS

•AMI BIOS on 8Mbit Flash ROM

•Serial Console Redirect

•PXE via Ethernet, USB device boot

•PnP, DMI 2.0, WfM 2.0 Power

Management

•User-configurable H/W monitoring

•Auto-configuration of hard disk

types

•Multiple boot options

•48-bit LBA support

Power

•ATX 12V

•Universal 24-pin +8-pin power

connectors

Regulatory

•FCC Class B (DoC)

•CE (DoC)

•BSMI (optional)

7

Chapter 2: Board Installation

You are now ready to install your motherboard. The mounting hole pattern of the

Tempest i5100W S5376 matches the SSI CEB specification. Before continuing with

installation, confirm that your chassis supports an SSI CEB motherboard.

How to install our products right… the first time

The first thing you should do is reading this user’s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, TYAN recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic

bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

NOTE

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN

DAMAGED.

8

2.1- Board Image

Tempest i5100W S5376WAG2NR/S5376WAG2NR5

This picture is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above

picture.

9

Tempest i5100W S5376G2NR

This picture is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above

picture.

10

2.2 - Block Diagram

Tempest i5100W S5376WAG2NR/S5376WAG2NR5

11

Tempest i5100W S5376G2NR

12

2.3 - Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

Jumper Legend



OPEN - Jumper OFF, without jumper cover



CLOSED – Jumper ON, with jumper cover

13

Jumper/Connector Function

P1 Rear Audio Header

J1 Front Panel Audio Header

J2 SO-DIMM Socket

LCM (J5) LCM Header

COM2 (J22) COM2 Connector

USB2 (J15) / USB3 (J16) USB Front Header

TYFP1 (J21) Front Panel Header

TYFP2 (J13) Front Panel Header 2 for Barebone

FAN CONN (J12) Fan Board Header for Barebone

SATA0~SATA5 Serial ATA Connector

PW1 24-pin Power Connector (EPS12V)

PW3 8-pin Power Connector (EPS12V)

PW2

Aux. Power Connector for TYAN Riser Card

(M2061)

CPUFAN1/CPUFAN2/

FAN1/FAN2/FAN3

4-pin Fan Header with Tachometer

JP1

SAS 1068E Device ID Change Jumper

Pin 1-2 closed: Device ID 58

Pin 2-3 closed: Device ID 59

JP2

VGA Enable/Disable Jumper

Pin 1-2 closed: Enable (default)

Pin 2-3 closed: Disable

JP3

Clear CMOS Jumper

Pin 1-2 closed: Normal (default)

Pin 2-3 closed: Clear

JP5

SAS 1068E Enable/Disable Jumper

Pin 1-2 closed: Enable (default)

Pin 2-3 closed: Disable

14

LCM

USB3

USB2

P1

J1

SATA0

SATA1

SATA2

SATA3

SATA4

SATA5

15

P1: Rear Audio Header (S5376WAG2NR and S5376WAG2NR5)

1 11

2 12

Pin Signal Pin Signal

1 MIC1_L_C 2 MIC1_R_C

3 GND 4 MIC1_JD

5 LINE1_L_C 6 LINE1_R_C

7 KEY 8 LINE1_JD

9 FRONT_L_C 10 FRONT_R_C

11 NC 12 FRONT_JD

J1: Front Panel Audio Header (S5376WAG2NR and S5376WAG2NR5)

1 9

2 10

Pin Signal Pin Signal

1 MIC_L 2 GND

3 MIC_R 4 PRESENT

5 LINE_R 6 MIC_JD

7 GND 8 KEY

9 LINE_L 10 LINE_JD

LCM (J5): LCM Header

5 1

6 2

Pin Signal Pin Signal

1 Link to MB V5 2 MB COM2 RX

3 KEY 4 GND

5 MB V5DUAL 6 MB COM2 TX

USB2 (J15) / USB3 (J16): USB Front Header

10 2

9

1

Pin Signal Pin Signal

1 USBPWR 2 USBPWR

3 USB-N 4 USB-N

5 USB-P 6 USB-P

7 GND 8 GND

9 KEY 10 GND

SATA0/1/2/3/4/5: Serial ATA Connector

7 GND

6 RXP

5 RXN

4 GND

3 TXN

2 TXP

7

1

1 GND

Connects to the Serial ATA ready drives via the

Serial ATA cable.

SATA0: J11 SATA1: J10

SATA2: J9 SATA3: J8

SATA4: J7 SATA5: J6

16

TYFP2

COM2

FAN CONN TYFP1

17

COM2 (J22): COM2 Connector

10

2

9

1

Pin Signal Pin Signal

1 DCD 2 DSR

3 RX 4 RTS

5 TX 6 CTS

7 DTR 8 RI

9 GND 10 KEY

FAN CONN (J12): Fan Board Header for Barebone

1

14

13

2

It is designed for barebone use only.

Pin Signal Pin Signal

1 CPU0-TACH 2 SYS4-TACH

3 CPU1-TACH 4 SYS5-TACH

5 FAN1-TACH 6 SYS6-TACH

7 FAN3-TACH 8 SYS7-TACH

9 FAN2-TACH 10 SYS8-TACH

11 GND 12 KEY

13 GND 14 HMO-FANPWM1

TYFP2 (J13): Front Panel Header 2 for Barebone

1

12

11

2

It is designed for barebone use only.

Pin Signal Pin Signal

1 LAN1 LED+ 2 LAN1 LED-

3 LAN2 LED+ 4 LAN2 LED-

5 NC 6 NC

7 ID LED+ 8 ID LED-

9 ID SW+ 10 ID SW-

11 KEY 12 NC

TYFP1 (J21): Front Panel Header

The Front Panel Header is used to connect some control or signal wires from

motherboard to chassis, such as HDD LED, power LED, power button, and

reset button.

HDDLED+

1 2

PWR LED+

HDDLED-

3 4

PWR LED-

Reset SW-

5 6

PWR SW+

Reset SW+

7 8

PWR SW-

GND

9 10

Warning LED+

Front_NMI#

11 12

Warning LED-

3VSB

13 14

Key

SMBus Data

15 16

GND

SMBus Clock

17 18

INTRU#

18

JP1

JP2

CPUFAN1FAN1

JP3

FAN3

CPUFAN2

FAN2

19

FAN1/FAN2/FAN3/CPUFAN1/CPUFAN2: 4-pin Fan Header

+1 2V

PWM

GND

Tachometer

1

+12V

PWM

GND

Tac hom et e r

1

Use this header to connect the

cooling fan to your motherboard to

keep the system at optimum

performance levels.

JP1: SAS 1068E Device ID Change Jumper

3

1

Pin 1-2 Closed: Device ID 58 (LSI IR RAID setting,

S5376WAG2NR only)

1

3

Pin 2-3 Closed: Device ID 59 (LSI Mega RAID setting,

S5376WAG2NR5 only)

JP2: VGA Enable/Disable Jumper

3

1

Pin 1-2 Closed: Enable (Default)

3

1

Pin 2-3 Closed: Disable

JP3: Clear CMOS Jumper

3

1

Normal

(Default)

1

3

Clear

Use this jumper when you forgot your system/setup

password or need to clear system BIOS setting.

How to clear the CMOS data

- Power off system and disconnect power

supply from AC source

- Use jumper cap to close Pin_2 and 3 for

several seconds to Clear CMOS

- Replace jumper cap to close Pin_1 and 2

Reconnect power supply to AC source

Power on system

20

PW2

JP5

La pagina sta caricando ...

Tyan S5376 Manuale utente

Questo manuale è adatto anche per

Tyan S5376 Manuale utente

in altre lingue

Documenti correlati

Altri documenti