Coemar PinLite Led RGB Instructions Manual

Coemar
Marca
Coemar
Modello
PinLite Led RGB
Categoria
Stroboscopi
Tipo
Instructions Manual
pin Lite LED
numero di serie/serial number
data di acquisto/date of purchase
fornitore/retailer
indirizzo/address
cap/città/suburb
provincia/capital city
stato/state
tel./fax/
Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro Pin Lite LED: que-
sti dati ci permetteranno di assistervi con la massima rapidità e precisione.
Please note in the space provided above the relative service information of the model and the retailer from
whom you purchased your
Pin Lite LED
: this information will assist us in providing spare parts, repairs or in
answering any technical enquiries with the utmost speed and accuracy.
ATTENZIONE
:
la sicurezza dell’apparecchio è garantita solo con l’uso appropriato delle presenti istruzioni, per-
tanto è necessario conservarle.
WARNING
: t
he security of the fixture is granted only if these instructions are strictly followed; therefore it is
absolutely necessary to keep this manual.
Users Manual Version 1.0
edition October 2006
Index
1. Packaging and transportation Pag. 4
1.1. Packaging “4
1.2. Transportation “4
2. General information Pag. 4
2.1. Important safety information “4
2.2. Warranty conditions “4
2.3. Certification “4
3. Product specifications Pag. 5
3.1. Technical characteristics “5
3.2. Dimensions “5
3.3. Projector components “5
4. Installation Pag. 6
4.1. Mechanical installation “6
4.2. Attaching a safety chain “7
4.3. Adjusting beam direction “7
4.4. Opening and closing up the projector “8
4.5. Adjusting the beam angle “8
5. Powering up Pag. 10
5.1. Operating voltage and frequency “10
5.2. Mains connection “10
6. DMX signal functions Pag. 11
6.1. Connecting DMX signal “11
6.2. Powering up “11
6.3. DMX addressing “12
6.4. DMX functions “12
7. Test function Pag. 13
8. Light ON function Pag. 13
9. Auto function Pag. 14
9.1. Master/Slave mode “14
9.2. Stand Alone mode “15
10. DR1 function Pag. 16
10.1. Setting up functionality using DR1 (FUNC) “16
10.2. Functions modes using DR1 (MODE) “17
10.3. Diagnostic functions using DR1 (MEAS) “18
10.4. Electronic alignment and software upgrade “18
10.5. Error messages using DR1 “19
11. Switch panel signals Pag. 20
12. Thermal protection Pag. 20
13. Maintenance Pag. 20
14. Spare parts Pag. 20
15. Accessory Pag. 20
16. Frequently asked questions Pag. 21
English
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest quality, both in compo-
nentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expe-
dite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This
information will assist in providing prompt and accurate advice from your Coemar service centre..
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come.
1.1. Packaging
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.
Packing list
Ensure the packaging contains:
1 Pin Lite LED
1 Instruction manual
1.2. Transportation
The Pin Lite LED should be transported in either its original packaging or in an appropriate flight case.
2.1. Important safety information
Fire prevention:
1. Never locate the fixture on a flammable surface.
2. Minimum distance from flammable materials: 0.5 m.
3. Minimum distance from the closest illuminable surface: 0,5 m.
4. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.
5. Connect the projector to mains power via a thermal magnetic circuit breaker.
Prevention against electric shock:
1. High voltage is present in the internal of the unit. Isolate the projector from mains supply prior to performing any function which
involves touching the internal of the unit.
2. For mains connection, adhere strictly to the guidelines outlined in this manual.
3. The level of technology inherent in the Pin Lite LED requires the use of specialised personnel for all service applications; refer all work
to your authorised Coemar service centre.
4. A good earth connection is essential for proper functioning of the projector. Never operate the unit without proper earth connection.
5. The mains cable should not come into contact with other cabling.
6. Never handle the unit with wet hands or in a damp environment.
Safety:
1. The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight of the unit.
2. Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary fixing point.
3. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
4. The external surface of the unit, at various points, may exceed 80°C. Never handle the unit until at least 10 minutes have elapsed
since the unit was turned off..
Protection rating of the body against liquids and solids:
1. The standard version of the fixture is classified ordinary apparatus; its protection grade against penetration by external agents,solid or
liquid, is IP 20
2. The IP version of the projector has an IP 65 protection rating; this indicates that it is protected against dust and significant showers
of water. This protection rating allows the fixture to be installed in an exposed location in inclement weather.
2.2. Warranty conditions
1. The fixture is guaranteed for a period of 12 months against manufacturing faults and faulty materials.
2. Faults due to incorrect operation or operation in an inappropriate manner are not covered by the warranty.
3. The warranty is immediately void if the fixture has been operated or serviced by unqualified or unauthorised personnel.
4. The warranty does not include fixture replacement.
5. The model and serial numbers must be supplied for any warranty claims or advice from our authorised service personnel.
2.3. Certification
1. The fixture satisfies the essential requirements of the directive EMC 89/336/EEC, 93/68/EEC, BT73/23/EEC.
2. The fixture is in accordance with the standard EN 50419 (RoHS) and satisfies the requirements of the directive 2002/96/EC (WEEE).
2. General information
1. Packaging and transportation
English
4
3.1. Technical characteristics
Power: 90/250 Vac 50/60Hz Autosensing
Nominal current: 0.18A @ 230Vac
0.45A @ 115V
Power factor: cos ϕ = 0,5
Led power: 36 Led x 1W
Minimum ambient temperature: -15°C / 5°F
Maximum ambient temperature: 35°C / 95°F
Weight: 3.6 Kg / 7.9 lbs
IP Rating: IP20 (standard version)
IP65 (IP version)
3.2. Dimensions
3.3. Projector components
The principal components of the Pin Lite LED are shown in the diagram below.
Descrizione dei componenti
1. IP20 rear panel
2. IP65 rear panel
3. Projector body
4. Dip-switch panel
5. Led control PCB
6. Switching power supply
7. Head
8. Lens group
9. Front frame
128.5mm
5.06”
140.9mm
5.55”
205mm
8.07”
168.9mm
6.65”
243.8mm
9.6”
3. Product specifications
5
English
6
4.1. Mechanical installation
Pin Lite LED may be floor mounted or hung from an appropriate structure in any position.
Permanent installation
Use the hole “A” (Ø13) on the yoke of the Pin Lite LED for robust, permanent installation.
Mobile installations
If hanging the fixture from a lighting truss or similar, we recommend the use of appropriate clamps “B”, affixed to the yoke in the hole
“A” provided, as shown in the following diagram.
Never install the fixture in a position in an accessible position to personnel who may ignore or be unaware of the safety directions men-
tioned in this manual.
ATTENTION!!
Always ensure that your support structure and fixings (bolts, clamps, etc.)
are rated to support the weight of the fixture.
4. Installation
English
4.2. Safety chain
When hanging the Pin Lite LED we recommend the use of a safety chain “C” affixed to the yoke and to the suspension device. The safety chain
should be either a metal wire rope or a metal chain, both suitably rated for the purpose.
4.3. Adjusting beam direction
The Pin Lite LED can be tilted to adjust the beam output. To perform this adjustment, follow the instructions set out below.
1. Loosen the handle “D” located on the side of the projector, thus allowing the inclination to be changed.
2. Adjust the projector’s tilt.
3. Refasten the handle “D” on the side of the projector.
7
English
4.4. Opening and closing up the projector
The various procedures which follow can only be performed with the projector housing removed.
To gain access to the internal of the projector use a suitable screwdriver to remove the 3 screws “E” which affix the front frame and
remove it.
In the IP version, to access the rear area (switch panel), fully untighten the 4 screws "F" that fix of the rear panel and remove it from the unit.
You should now have complete access to the internal of the projector and can proceed to carry out the procedures described below.
Close the unit by following the previous points the other way round.
4.5. Adjusting the beam angle
Several optional optical groups are available for Pin Lite LED. They are used to vary the beam dimension and make it suitable for dif-
ferent lighting applications and specifically: a group of lenses for a larger projection angle, a flood reflector and several filters that can
be fitted either internally or externally to the unit
The standard optical group, fitted on Pin Lite LED, is composed by a group of lenses that gives 12° beam angle.
Here following you will find instructions to install different optical groups.
1. Open the unit as shown on paragraph 4.4 Open and close the unit
2. Remove the 3 screws “G”.
3. Replace the lenses “L” and ensure that the led of “H” disc fit perfectly in the lenses seats
If you wish to use an optional filter holder (code CO9188) follow the instructions as per point 4 and 5.
4. After having positioned the lenses group insert the “M” filter
5. Lock it with the “N” filter holder
6. Tighten the 3 “G” fixing screws
7. Close the unit
ATTENTION!!
Remove mains power prior to opening up the projector.
In the IP version, before close up the unit, check that the garnishings are inserted in their places.
Both screws “E” and “F” must be uniformly fixed, screwing them alternately in short steps.
8
English
To further increase the beam angle the “R” flood reflector is available (code CO9187) and it must be fitted instead of the lenses group
and filter holder.
To vary the wideness of the beam without opening the unit, it’s possible to install an external filter holder “S” (code CO9188/1), as shown
on following drawing.
The following table details the range of beam angle and diffusion filters available for the Pin Lite LED.
Optical group Beam angle (1/2 peak angle)
Narrow Lenses (standard) 10°
Narrow Lenses + Light Frost Filter 12°
Narrow Lenses + Frost Filter 14°
Narrow Lenses + Strip Frost Filter Beam Shake
Medium Lenses (cod. CO9186) 20°
Medium Lenses + Light Frost Filter 22°
Medium Lenses + Frost Filter 24°
Medium Lenses + Strip Frost Filter Beam Shake
Flood 81°
9
English
5.1. Operating voltage and frequency
The fixture may operate at voltages ranging from 90 to 250V AC at a frequency of 50 or 60 Hz.
It is not necessary to effect any setup procedures, Pin Lite LED will automatically adjust its operation to suit any
frequency or voltage within this range.
5.2. Mains connection
Cabling
TThe mains cable provided can be one of the following type:
1. Neoprene cable Type HO7RN-F 3x1.5 mmq (cod. CV5333)
2. Neoprene cable type FT-2 P-7K 3x1.5 mmq (cod. CV5307)
Both types are suitable for outdoor applications and comply to the most recent international standards: CEI 20-19, UNEL 35364,
CENELEC HD 22.
N.B. In case of cable replacement, similar cable with comparable qualities must be used exclusively (cable 3x1.5 ø external 10 mm, rated
450/750V, operating temperature -25° +60°.
Connection to mains power
for connection purposes, ensure you plug is of a suitable rating:
•230/240V 0.2 amps constant current.
•208V 0.25 amps constant current.
•100/115V 0.5 amps constant current.
Locate the mains cable which exits the base of the unit and connect as shown below:
ATTENTION!!
• The use of a thermal/magnetic circuit breaker for each fixture is recommended. Strict adherence to regulatory norms
is strongly recommended.
• Pin Lite LED should not be powered through a Dimmer as this may damage the internal switching powersupply.
• Prior to connecting the device to mains power, ensure that the mains characteristics are within the recommended
range for use with the Pin Lite LED.
• A good earth connection is essential for the correcdt operation of the Pin Lite LED. Never install the unit unless the
yellow/gree earth cable is securely connected.
• All cabling and connections should be carried out by suitably qualified personnel.
5. Powering up
10
English
Pin Lite LED can operate in two modes:
1. using DMX512 control signal
2. automated “STAND ALONE” or “MASTER/SLAVE” modes (see chapter 9. AUTO function)
6.1. Connecting DMX signal
Control signal is digital and is transmitted via two pair screened cable, as recommended in international standards for the transmission
of DMX512. Connection is serial, utilising the XLR3 sockets located on the rear panel of the Pin Lite LED.
Signal connection via the XLR3 connectors
Connection is to international standards. Connection is as indicated below:
pin 1 = GND
pin 2 = data -
pin 3 = data +
Should your DMX 512 controller output signal via a cannon XLR5 (5 pin), pins 4 and 5 should remain unconnected.
6.2. Powering up
After having followed the preceding steps, turn on mains power on to the unit.
The POWER led located near the dip-switch panel will come on.
Turning on power with DMX signal connected.
The yellow DMX led will flash to indicate that DMX 512 is being correctly received. If the yellow led is off, DMX signal is not being
received (see section 16. Frequently asked questions).
ATTENTION!!
Ensure that all data conductors are isolated from one another, the screening and the metal housing of the connector.
Pin number 1 and the housing should never be connected to mains power.
6. DMX signal functions
11
English
6.3. DMX addressing
Via the dip-switch panel, it is possible to assign a DMX address to the fixture. The address is determined by the sum of the values asso-
ciated with the dip switches set to the on position.
Each Pin Lite LED utilises 6 channels of DMX 512 signal for complete control.
IMPORTANT NOTE: the following points are valid for all the instructions which follow.
1. Setting a dip-switch to the ON position activates its function
2. The DMX address may be altered without the need to turn the Pin Lite LED off.
The following are examples only for setting DMX addresses.
6.4. DMX functions
channel function type of control effect
1
master
dimmer
proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2 red proportional proportional control of the percentage of red colour from 0 to 100% 0 - 255 0% - 100%
2 (A) speed proportional
fade speed between colours of the program selected from channel 6; from
fast to slow (from 1 second to 1 minute)
0-255 0% - 100%
3 green proportional proportional control of the percentage of green colour from 0 to 100% 0 - 255 0% - 100%
3 (A) pause proportional
control of the pause time between colours (steps) of the program selected
from channel 6; the pause time is adjustable proportionally from 1 second
to 3.30 minutes
0-255 0% - 100%
4 blue proportional proportional control of the percentage of blue colour from 0 to 100% 0 - 255 0% - 100%
step no effect 0 - 9 0% - 4%
proportional variable speed strobing effect, from slow to fast 10 - 57 4% - 22%
step stop strobe 58 - 59 23% - 23%
proportional
sequenced pulse effect, slow closing, fast opening
(variable speed pulsing, from slow to fast)
60 - 108 24% - 42%
step stop strobe 109 - 110 43% - 43%
proportional
sequenced pulse effect, fast closing, slow opening
(variable speed pulsing, from slow to fast)
111 - 159 44% - 62%
step stop strobe 160 - 161 63% - 63%
proportional
random strobe effect with variable speed from slow to fast and
synchronised colours
162 - 207 64% - 81%
step stop strobe 208 - 209 82% - 82%
proportional
random strobe effect with variable speed from slow to fast and
non-synchronised colours
210 - 255 82% - 100%
no effect 0 - 9 0% - 4%
automated program 1 10 - 50 4% - 20%
automated program 2 51 - 91 20% - 36%
automated program 3 92 - 132 36% - 52%
automated program 4 133 - 173 52% - 68%
random program repeat 174 - 214 68% - 84%
repeat all programs in sequence 215 - 255 84% - 100%
5
strobe effect
step
6
Note 1: the second function 2 (A) is enabled when channel 6 is active
Note 2: the second function 3 (A) is enabled when channel 6 is active
automated
functions
decimal
percentage
Pin Lite LED number 2 Address DMX 007
is obtained by setting dip-switches 1, 2 & 4 to the ON position
Pin Lite LED number 1 Address DMX 001
is obtained by setting dip-switch 1 to the ON position
12
English
With the dip-switch set to the ON position, Pin Lite LED will test each individual channel without the need for a DMX controller to be
connected.
For example:
Via this function the leds of the Pin Lite LED may be set to always on at a predetermined intensity.
When set to ON the dip-switch, illumination level and colour can be set by a combination of settings as shown in the table below.
Other examples of possible setting combinations are shown below.
ATTENTION!!
Setting the Light ON dip-switch to active inhibits control via DMX signal.
The three colour dip-switches set to the OFF position turn off the colour.
LIGHT ON dip-switch set to ON
RED off
GREEN off
BLUE at 100% (dip-switches 64, 128, 256 set to ON)
LIGHT ON dip-switch set to ON
RED at 20% (dip-switch 1 set to ON)
GREEN at 30% (dip-switch 16 set to ON)
BLUE at 50% (dip-switch 256 set to ON)
dip-switch 1 dip-switch 2 dip-switch 4 Red
on off off illumination level 20%
off on off illumination level 30%
on on off illumination level 40%
off off on illumination level 50%
on off on illumination level 60%
off on on illumination level 80%
on on on illumination level 100%
dip-switch 8 dip-switch 16 dip-switch 32 Green
on off off illumination level 20%
off on off illumination level 30%
on on off illumination level 40%
off off on illumination level 50%
on off on illumination level 60%
off on on illumination level 80%
on on on illumination level 100%
on off off illumination level 20%
off on off illumination level 30%
on on off illumination level 40%
off off on illumination level 50%
on off on illumination level 60%
off on on illumination level 80%
on on on illumination level 100%
dip-switch 256
Blue
dip-switch 64
dip-switch 128
8. Light ON Function
set the dip-switch to ON on the Pin Lite LED.
The fixture will perform a quick sequential channel test
7. Test function
13
English
This function can be used to determine the operating mode of the projector (either STAND ALONE or MASTER/SLAVE), make pro-
gram selections or alter the crossfade times. Setting this function to on inhibits control via DMX signal.
9.1. MASTER/SLAVE mode
In MASTER/SLAVE mode, it is possible to control, via a projector set as MASTER, a series of Pin Lite LED units set to act as SLAVE fixtures.
The table below displays the settings required for fixtures to be connected in this manner.
To configure a Pin Lite LED as MASTER is simply a matter of setting the Auto dip-switch
to the ON position and selecting a program for it to follow by making a selection from the
following dip-switches: 1-2-4-8-256. There are 4 programs which can be selected.
- dip switches 1-2-4-8 select programs 1, 2, 3, and 4 respectively.
- dip-switch 256 runs all four programs sequentially
To configure a Pin Lite LED as SLAVE is simply a matter of setting the Auto dip-switch to
the ON. All other dip-switches should be set to OFF.
Pin Lite LED
set to SLAVE
256
auto
test
light on
DR1
1
2
4
8
16
32
64
128
SLAVE
ATTENTION!!
It is only possible to select one program at a time.
Pin Lite LED set as MASTER
running program 1
256
auto
test
light on
DR1
1
2
4
8
16
32
64
128
MASTER
9. Auto function
14
English
After having selected the program you wish to run, dip-switches 16 and 32 may be used to set the wait time for each scene in the
selected program. In this manner, programs can be made to run faster or slower according to your requirements. The following table
outlines the dip-switch settings and their associated wait times.
Via dip-switches 64 and 128 it is possible to set the fade times for each scene in the selected program. The following table outlines the
dip-switch settings and their associated fade times.
The timing for each scene in a program is therefore a sum of the crossfade and hold times as set via these dip-switches.
The following table gives an example of a possible setting.
9.2. STAND ALONE mode
In STAND ALONE mode the projector operates independently with no need for DMX signal. It is possible to select the program which
the projector runs and to alter the hold and crossfade times.
To configure the Pin Lite LED as STAND ALONE simply set dip-switch Auto to the ON
position and select the program you wish to run and the hold and crossfade times to fol-
low, as described in the previous section.
Pin Lite LED set as STAND ALONE
running program 1
256
auto
test
light on
DR1
1
2
4
8
16
32
64
128
STAND ALONE
ATTENTION!!
When the AUTO function is selected DMX signal reception is disabled to avoid system conflicts.
Pin Lite LED set as a MASTER running program 3
hold time 30 sec. crossfade time 10 sec.
Set the AUTO and 4 dipswitches to ON will select the fixture as MASTER
running program 3.
Setting dip-switch 16 to OFF and 32 to ON will set a hold time of 30 sec.
Dip-switch 64 to ON and 128 to OFF will set a crossfade time of 10 sec.
dip-switch 64 dip-switch 128
off off crossfade time 3 second
on off crossfade time 10 second
off on crossfade time 30 second
on on crossfade time 1 minute
speed (fade time)
dip-switch 16 dip-switch 32
off off hold time 3 second
on off hold time 10 second
off on hold time 30 second
on on hold time 1 minute
time (wait time)
15
English
This function allows for the transmission of bidirectional data with the DR1 (cod. CO9703). Via the DR1 (display remote) it is possible
to remotely access, view and alter all the fixture’s parameters and settings.
The DR1 remote display unit allows the user to:
To initiate communications with the Pin Lite LED the DR1 must be installed into the DMX signal chain between the fixture and the
controller following the instructions located internally on the unit.
The DR1 dip-switch must be set to the ON position; from this point on, dip-switches 1 to 128 take on the task of assigning an iden-
tifying value (ID) to the fixture. They no longer set the fixture’s DMX address, which is done by the DR1. The maximum number of
unique IDs available in the DR1system is 250; dip-switch 256 has no functionality.
An example of a possible configuration is shown below:
10.1. Setting up functionality via DR1 (FUNC)
Using the inbuilt functionality of the Pin Lite LED via the DR1, it is possible to alter the function settings of the fixture. The following
diagram illustrates the menu navigation system of the DR1 in FUNC.
RED
Test red channel
☞
menu
FUNC MEAS
AOO1
MODE
☞
+o--
☞
+o--
TEST
test
Function test
DFSE
default functions setting
To set all the functions at the original values,
but for DMX address and for working time.
RESE
reset
Reset function
☞
+o--
☞
+o--
☞
enter
☞
+o--
☞
enter
☞
+o--
☞
+o--
☞
+o--
☞
+o--
es.
0127
☞
enter
☞
enter
☞
+o--
☞
enter
☞
enter
es.
0127
☞
enter
☞
enter
☞
+o--
es.
0127
☞
enter
☞
enter
☞
+o--
es.
0127
☞
enter
☞
enter
☞
+o--
SURE
☞
enter
☞
enter
0020
SURE
0020
0020
0020
☞
enter
-– -– -– -–
reset activation
GREE
Test green channel
BLU
Test blu channel
STRB
Test strobo
STOR
To record the scene of the unit.
If DMX signal is not applied,
the recorder setting will appear
at the end of reset operation
when the unit is switched on.
Pin Lite LED set to ID 13 and DR1 active
configured by setting dip-switch DR1 to ON
and dip-switches 1, 4 and 8 to ON
Edit and set (MODE):
1) DMX address
2) function mode
Execute (FUNC):
1) Function test
2) Software update
3) Color alignment
Monitor (MEAS):
1) the current Software Version loaded
2) temperature
3) led operating life
4) projector operating life
5) presence and characteristics of incoming DMX 512
6) error messages
7) ID code
ATTENTION!!
All the function in this chapter are exclusively activateable from DR1.
10. DR1 function
16
English
10.2. Function modes using DR1 (MODE)
Using the inbuilt functionality of the Pin Lite LED via the DR1, it is possible to alter the function mode of the fixture. The following dia-
gram illustrates the menu navigation system of the DR1 in MODE.
FUNC
☞
menu
AOO1
MODE
☞
+o--
MEAS
☞
+o--
DMX
DMX function
DMX function mode
☞
enter
AOO1
☞
enter
-- MA--
master function
Master unit
PRG.1
Example
program 1
☞
enter
PROG
program
To select the number of
program to run
SPEE
speed
Memories running time (sec)
WAIT
waiting time
Waiting time among
memories (sec)
☞
+o--
☞
+o--
☞
+o--
☞
+o--
☞
+o--
☞
enter
P ALL
All programs
to
0.1
0210
to
PRG4
To program 4
☞
+o--
☞
enter
0.1
0060
☞
enter
☞
enter
☞
enter
☞
enter
PRG1
From program 1
☞
enter
☞
enter
☞
enter
☞
enter
☞
enter
--SL--
slave function
Slave unit
--SL--
☞
enter
☞
+o--
☞
+o--
☞
+o--
17
English
10.3. Diagnostic functions using DR1 (MEAS)
Using MEAS mode, it is possible to carry out several digital parameters checks and autodiagnostics. The following diagram illustrates
the menu navigation system of the DR1 in MEAS.
10.4. Electronic alignment and software upgrade
The display panel of the DR1+ allows for the electronic alignment of the colors. This procedure is performed by Coemar at the factory.
It may be useful to perform this procedure in the case of internal components being replaced (electronic parts).
Altering the factory settings may radically alter the functioning of the projector. Carefully read all of the following prior to attempting
any changes.
1. Press the menu button and then enter to confirm.
2. Press the + or - button until
FUNC is displayed. Then press enter.
3. Press the + or - button until
RESE is displayed.
4. Press the enter and menu buttons simultaneously, holding them for at least 10". The motors will perform a reset and the display will
show
-- -- -- -- for a few seconds. After this, the display will show ALIG confirming that you have entered electronic calibration
mode.
ATTENTION!!
The alignment procedure can only be carried out when DMX 512 signal is connected.
ATTENTION!!
This procedure should only be undertaken by qualified and experienced technical personnel..
☞
menu
F U NC MEAS
AOO1
MODE
☞
+o--
☞
+o--
58C
Temperature
measurement
TEMP
temperature
Misure the led housing internal
temperature in °C
☞
enter
10
DMX value reading
255
DMX value reading
DMIN
DMX value on each channel
Reading of DMX value(0/255), received by
each of the 6 channels on DMX512 line.
CH01
From channel 1
CH06
To channel 6
☞
enter
☞
enter
☞
enter
☞
+o--
RATE
DMX rate
Reading of DMX512 signal value
☞
+o--
☞
enter
24
Value reading
NDMX
No DMX signal
ALRM
alarm
Reading of warning message sequences (errors)
shown after reset operation .
☞
+o--
☞
enter
NO.AL
No alarm
MAER
Warning messages
S.VER
software
Reading fo software release code
02,01
Software release code
☞
enter
1--250
Numeric value
☞
enter
ID
ID number setting
To set the unit’s ID number from 0
(no ID) to 250.
10
Value reading
1230
Value reading
HOUR
working time
Working time (in hour)
☞
enter
☞
+o--
☞
enter
☞
enter
LIFE
Led life
UNIT
Projector life
☞
+o--
☞
+o--
☞
+o--
☞
+o--
☞
+o--
☞
enter
☞
+o--
☞
+o--
18
English
UPLOAD function
Using this function it is possible to upload software to the Pin Lite LED using a DR1+.
For further information, consult the DR1 manual.
DOWNLOAD function
Using this function it is possible to download software from the Pin Lite LED to a DR1+.
For further information, consult the DR1 manual.
10.5. Error messages using DR1
MESSAGE CODE DESCRIPTION
DTER
DATA Error
The initial configuration settings are fautly or have been loaded incorrectly. The projector has loaded its default
configuration. Turn the projector off and on again and if the error persists the EEPROM is either defective or
absent; refer to your Coemar service centre for a replacement component.
ADER
DMX ADDRESS Error
The projector is not receiving all the DMX channels necessary for its operation. Check the DMX address and the
control console operation. Note that some controllers may not generate all 512 channels of signal.
MAER MASTER MODE Error
This message indicates that the user has attempted to set the unit to MASTER mode whilst DMX signal is still
being received. Detach any DMX control signal or remove MASTER mode settings.
☞
menu
AOO1
FUNC
☞
enter
RESE
reset
Reset function
M I N.R
red led alignment
Alignment led red minimum intensity
☞
enter
0001
☞
enter
☞
+o –
0010
ALIG
alignment
Colour setting
☞
+o –
M I N.G
led green alignment
Alignment led green minimum intensity
☞
enter
0001
☞
enter
☞
+o –
0012
☞
+o –
M I N.B
led blue alignment
Alignment led blue minimum intensity
☞
enter
0001
☞
enter
☞
+o –
0015
☞
+o –
MAX.R
led red alignment
Alignment led red maximum intensity
☞
enter
0250
☞
enter
☞
+o –
0255
☞
+o –
MAX.G
led green alignment
Alignment led green maximum intensity
☞
enter
0250
☞
enter
☞
+o –
0252
☞
+o –
MAX.B
led blue alignment
Alignment led blue maximum intensity
☞
enter
0250
☞
enter
☞
+o –
0248
☞
+o –
END
end
To end the electronic calibration
procedure and to record it
☞
enter
A001
☞
+o –
☞
+o –
☞
enter
UPLD
Upload
Software upload from DR1+
☞
+o--
0000
Upload value
SURE
☞
enter
☞
enter
DULD
Download
Software download to DR1+
☞
+o--
0000
Download value
SURE
☞
enter
☞
enter
es.
es.
es.
es.
es.
es.
Press together enter and menu keys for
10 seconds: the display will show this menu
19
English
The two leds on the dip-switch panel indicate the functionality of the Pin Lite LED.
A thermal sensor in the body of the Pin Lite LED protects the fixture against overheating. The sensor operates by removing power to
the leds should the operating temperature exceed the factory preset.
Whilst every possible precaution has been taken to ensure the trouble-free operation of your Pin Lite LED, the following periodic main-
tenance is highly recommended. We recommend that the voltage to the unit be removed prior to any maintenance procedure taking
place.
Mechanicals
Check that the units is not mechanically damaged. Regularly clean the glass by using a soft cloth with a specific cleaning liquid and, if
necessary, replace the damaged parts.
Electrical components
Check all electrical components for correct earthing, oxidation and proper attachment of all connectors, cleaning and refastening if necessary.
All the components of the Pin Lite LED are available as spare parts from your Coemar service centre.
Accurate description of the fixture, model number, and type will assist us in providing for your requirements in an efficient and effective
manner.
In the table below are listed all the accessory of the Pin Lite LED and the related Coemar code.
Descrizione Codice
1. 12° lens assembly CO9186/1
2. 30° lens assembly CO9186
3. Flood CO9187
4. Inside gel CO9188
5. Gel CO9188/1
6. Rear panel IP20 silver PAN09
7. Rear panel IP20 black PAN09/1
8. Rear panel IP65 silver PAN10
9. Rear panel IP65 black PAN10/1
10. XLR3 connector CO9189/1
11. XLR5 connector CO9189
15. Accessory
14. Spare parts
ATTENTION!!
Always remove mains power prior to opening up the fixture!
13. Maintenance
12. Thermal protection
Led Function Led on Led off Led flashing
Green
Power Present Absent Undefined
Yellow
DMX state
DMX poorly
connected
No DMX signal DMX OK
11. Switch panel signal
20
English
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Coemar PinLite Led RGB Instructions Manual

Coemar
Marca
Coemar
Modello
PinLite Led RGB
Categoria
Stroboscopi
Tipo
Instructions Manual
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti