Before commissioning the machine, read operating
instructions and observe warnings and safety instructions!
Operating Instructions No. 998715-A 03.16
3901
&
Verticutter
8200-V6R
8200 971
with wheel drive
Operating Instructions
Translation of the original operating instructions
50 cm
2 agria Verticutter 8200-V6R
Symbols, Name Plate
Please complete:
Machine Type No. ......................
Identification No.
...................................................
Engine Type: ..............................
Engine No. .................................
Date of Purchase: ......................
For name plate, refer to p3/fig. A/12.
For Engine type and number, refer
to p3/fig. B/8.
Please state these data when
ordering spare parts to avoid wrong
deliveries.
Only use original agria spare
parts!
Specifications, figures and
dimensions stated in these
instructions are not binding. No
claims can be derived from them. We
reserve the right for improvements
without changing these instructions.
This delivery comprises:
l
Operating instructions
l
Verticutter – basic machine
l
Steering handle with fixings
Symbols
W
Warning – Danger
Important information
Choke
Fuel
Öl
Engine Start
Engine Stop
Engine oil level
Air filter
Air cooling
Visual check
Fast
Slow
Knife shaft drive
Wheel drive
Open (unlocked)
Closed (locked)
Clockwise
Anti clockwise
è - Serviceç
= contact Your agria workshop
agria Verticutter 8200-V6R 3
Designation of Parts
Figure A
Figure B
Figure C
4 agria Verticutter 8200-V6R
Figure A
1 Engine
2 Top part of steering handle
3 Speed control lever
4 Handle for wheel drive engagement
5 Handle for engagement of knife shaft drive
6 Engine-off switch
7 Grip handle for fast lift-out
8 Bowden cable set screw of wheel drive
9 Bowden cable set screw of knife shaft drive
10 Wheel scraper
11 Rear wheel (drive wheel)
12 Name plate/ID no.
13 Knife shaft bearing
14 Front wheel
15 Knob for slitting depth adjustment
16 Knife shaft housing
17 Belt guard
Figure B
1 Fuel tank
4 Starter handle
5 Recoil starter
6 Radiator grille
8 Engine type no.
9 Engine oil drain plug
10 Engine oil filler plug
11 Fuel tap
13 Spark plug/spark plug connector
Figure C
2 Carburetor
3 Air filter
4 Governor linkage
5 Exhaust with guard
Designation of Parts
agria Verticutter 8200-V6R 5
Index
Amount of Delivery .................. 2
Recommendations
Lubricants, Anti-Corrosive Agents.... 6
Fuel ................................................... 6
Maintenance and Repair .................. 6
Designation of Parts ................ 3
Unpacking, Assembly .............. 7
1. Safety Instructions......... 8–12
2. Specifications
Dimensions ..................................... 12
Verticutter........................................ 13
Engine............................................. 13
Noise Level ..................................... 13
Vibration Acceleration Value........... 13
Operation on Slopes....................... 13
3. Devices and Operating
Elements
Engine............................................. 14
Knife Shaft Drive ............................. 15
Wheel Drive .................................... 15
Slitting Depth Adjustment ............... 16
Fast lift-out Mechanism .................. 16
4. Commissioning and
Operation
Commissioning the Machine .......... 17
Starting the Engine ......................... 18
Shutting off the Engine ................... 19
Verticutter Operation....................... 20
General Comments on
Verticutter Turf Care........................ 21
5. Maintenance
Machine .................................... 22–25
Wheel drive ............................... 26–27
Wheels ............................................ 27
Wheel Scraper ................................ 27
Knife Shaft Drive ............................. 28
Knives ............................................. 29
General ........................................... 30
Cleaning.......................................... 30
Storage ........................................... 31
Wiring Diagram....................... 31
6. Troubleshooting............ 32–33
Varnishes, Wear Parts............ 33
Inspection and Maintenance
Chart........................................ 34
Declaration Conformity ......... 35
Note fold-out page!
Figs. A, B, C .............................. 3
3
5
6
2
1
4
6 agria Verticutter 8200-V6R
Recommendations
Lubricants and
Anti-Corrosive Agents
Use the specified lubricants for en-
gine and gearbox (see “Specificati-
ons”).
We recommend using Bio-lubrica-
ting oil or Bio-lubricating grease
for “open” lubricating points or nipp-
les (as specified in the operating in-
structions).
We recommend using Bio-slushing
oil for preservation of machines and
implements (do not apply on painted
external covers). Oil can be brushed
or sprayed on.
Anti-corrosive agents are environ-
mentally friendly and degrade fast.
Using ecologically safe Bio-lubri-
cants and Bio-anti-corrosives, you
contribute to environmental protec-
tion and to the wellbeing of humans,
animals and plants.
Fuel
This engine runs smoothly on
commercial unleaded regular and
supergrade petrol as well as on
leaded supergrade petrol.
Do not add oil to petrol.
If, for environmental reasons, you use
unleaded petrol, make sure the fuel is
drained completely when shutting down
the engine for more than 30 days. This
is to prevent resin residue from
depositing in the caburetor, fuel filter,
and tank. Or add a fuel stabilizer to the
fuel.
For further instructions refer to “Engine
Preservation”.
Maintenance and Repair
The trained mechanics of your agria
workshop carry out expert maintenance
and repair.
You should only carry out major
maintenance work and repairs on your
own, if you have the proper tools and
knowledge of machines and internal
combustion engines.
Do not hammer against the flywheel
with a hard object or metal tools as it
might crack and shatter in operation
causing injuries and damage. Only use
suitable tools for pulling the flywheel.
agria Verticutter 8200-V6R 7
Unpacking and Assembly
l
Open the top of the
cardboard box.
l
Cut the box open on all
four corners and fold
down the sides.
l
Swivel the top part of
steering handle (1) to the
rear and mount the moun-
ting parts (2-4)
l
Tighten all screwed
connections and attach
the caps (5) to the nuts.
l
Mount the steering
bracket (7) with the spring
washers (8) and screws
(9) at the steering hand-
le.
l
Attach the Bowden and
electric cables to the
steering handle’s bottom
part, using the cable ties
(6). Ensure that all cables
are routed properly.
Ensure they are not bent
or squeezed.
Starting-up
See instructions on page
17.
1 Top part of steering handle
2 Truss head screw M8
3 Oval washer
4 Locking nut M8
5 Nut cap
6 Cable tie
7 Steering bracket
8 Spring washer
9 Screw M6
8 agria Verticutter 8200-V6R
1. Safety Instructions
Before starting the engine, read the
operating instructions and note:
Warning
This symbol marks all paragraphs
which affect your safety. Pass all safety
instructions on to other users and
operators.
Due Use
With its rotating knives, the verticutter
is constructed for use on grassed
surfaces for in-depth cleaning and the
removal of thatch, moss and flat-
growing weeds from the grass (due
use).
Any other type of use is considered
undue. The manufacturer is not liable
for any damages resulting from undue
use, for which the risk lies with the user
alone.
For reasons of safety do not use the
verticutter to drive other tools or
attachments. The verticutter (equipped
with wheel drive) is not suited for pulling
lawn sweepers and spreaders. The
same applies for attaching trailers to
ride on or transport clippings. The only
attachment allowed on the verticutter
is the grass collecting box provided by
the manufacturer.
Due use includes compliance with
manufacturer’s instructions on
operation, service and maintenance.
Any unauthorized modifications to the
verticutter render manufacturer liability
null and void.
General Instructions on Safety
and Accident Prevention
Basic Rule:
The standard accident prevention
regulations must be adhered to, as well
as all other generally accepted rules
governing operational safety,
occupational health and road traffic
regulations.
Check the verticutter for operational
safety each time you take up operation.
Only persons familiar with the
verticutter and instructed on the
hazards of operation are allowed to
use, service and maintain the machine.
Teenagers younger than 16 years are
not allowed to operate the verticutter!
Only work in good light and visibility.
Operator’s clothes should fit tight. Avoid
wearing loose fitting clothes. Wear so-
lid shoes.
Note the warning and instruction signs
on the verticutter for safe operation.
Comply for your own safety.
When transporting the verticutter on
vehicles or trailers outside the area to
be cultivated, ensure that the engine is
turned off.
Careful with rotating tools – keep at a
safe distance!
The knives may coast due to flywheel
mass on the engine. Keep at a safe
distance while the shaft is coasting.
Before you service or maintain the
verticutter, wait until the shaft has come
to a complete stop and remove the
spark plug.
1
agria Verticutter 8200-V6R 9
1. Safety Instructions
Beware of coasting tools. Before you
start working on them wait until they
have come to a complete stop.
Do not change engine governor
settings. High engine speed increases
risk of accidents.
Working Area and Hazardous
Area
The user is liable to third parties
working within the machine’s working
range.
Staying in hazardous area is not
permitted.
Check the immediate surroundings of
the machine before you start it. Watch
out for children and animals.
Before you start work, clear the area
from any foreign object. During
operation, always watch out for further
objects and remove them in time.
For operation in enclosed areas, ensure
that a safe distance is kept to
enclosures to prevent damage to tools.
Watch out during slitting operation to
prevent the knives from hitting
obstacles such as border stones,
kerbstones, roots, etc.
Shut off the engine before you transport
the verticutter outside the area of
operation.
Operation and Guards
Before you start the engine
Become familiar with all guards and
controls and their functions. Above all,
learn how to turn the engine off quickly
and safely in an emergency.
Ensure that all guards are fitted and
positioned to provide protection.
Starting the engine
Do not start engine in closed rooms.
The carbon monoxide contained in the
exhaust fume is extremely toxic when
inhaled.
Careful when starting the verticutter
and during operation. Keep your
hands and feet off the rotating
knives!
Do not upend or tilt the verticutter when
you start the engine.
Do not step in front of the verticutter to
start the engine.
When starting the engine, ensure the
wheel drive (if equipped) is not
engaged
Do not use assist-starting liquids when
using electrical assist-starting devices
(jumper cable). Danger of explosion.
1
10 agria Verticutter 8200-V6R
1. Safety Instructions
Operation
Never leave the operator’s position at
the steering handle while the machine
is at work.
Never adjust the handles during work
– danger!
The operator always has to keep at a
safe distance from the rotor housing as
set by the steering handle. This applies
in particular for turning the verticutter.
Do not pull but push the verticutter
when making a turn.
If blockages occur, turn off the engine
and clean the machine with an
appropriate tool.
In case of damage to the verticutter,
immediately turn off the engine and
have it repaired.
If steering causes problems,
immediately bring the verticutter to a
halt and turn it off. Have the malfunction
removed without delay.
To prevent the machine from slipping
in hillside operation, make sure it is
secured by another person who uses
a bar or a rope to hold the machine.
This person has to walk further up the
slope and at a safe distance from the
knife shaft housing.
If possible, always work across the
slope.
End of Operation
Never leave the verticutter unattended
with the engine running.
Before you leave the verticutter, turn off
the engine.
Secure the verticutter against
unauthorized use. If the machine is
equipped with an ignition key, remove
the key. For all other versions, remove
the spark plug connector to secure the
machine.
Grass Collecting Box
If the grass box is not removed/attached
properly, stray stones or wood may be
thrown out by the rotating knives and
injure the operator.
Before you remove the grass box or
adjust the slitting depth, shut off the
engine and wait until the knife shaft has
come to a stop.
Maintenance
Never carry out any maintenance or
cleaning with the engine running.
In addition, always remove spark plug
connector before you work on the
engine.
Regularly check all guards and tools
exposed to wear and tear and replace
them, if necessary.
Replace damaged knives.
Always wear safety gloves and use pro-
per tools when exchanging knives.
Do not carry out repairs like welding,
grinding, drilling, etc. on structural and
safety-relevant parts!
Keep the verticutter clean to avoid risk
of fire.
Check nuts and bolts regularly for tight
fit and re-tighten them, if necessary.
1
agria Verticutter 8200-V6R 11
1. Safety Instructions
Ensure that you re-install all guards and
adjust them properly after maintenance
and cleaning.
Only use original agria spare parts. All
other conventional spare parts must
correspond to quality and technical
requirements specified by agria.
Storage
It is not allowed to store the verticutter
in rooms with open heating.
Never park the verticutter in closed
rooms with fuel left in tank. Fuel
vapours are hazardous.
Engine, Fuel, and Oil
Never let the engine run in closed
rooms. Extreme danger of intoxication!
Careful when dealing with fuel. Great
danger of fire!
Never refill fuel close to open fire,
inflammable sparks or hot engine parts.
Do not refill fuel in closed rooms. Do
not smoke when refilling!
Refill only with the engine switched off
and cooled down.
Do not spill any fuel, use a proper filling
device.
In case of fuel-spillage, push the
verticutter away from the spillage
before you start the engine.
Ensure the fuel is of required quality.
Store fuel in approved cans only.
Store anti-corrosive agents and
stabilizing liquids out of reach of
children. If sickness and vomiting occur,
see a doctor. If fuel has contacted eyes,
rinse them thoroughly, avoid inhaling of
vapours.
Read and observe enclosed
instructions.
Before you dispose of opened and
seemingly empty pressurised tins (e.g.
of assist-starting liquids) make sure
they are completely empty. Empty them
in ventilated places safe from spark
formation or flames. If necessary,
dispose of tins in hazardous waste
deposits.
Be careful when draining hot oil –
danger of burns.
Ensure the oil is of required quality.
Storage is in approved cans only.
Dispose of oil, greases, and filters
separately and properly.
Electrical System
Persons having a pacemaker must not
touch live parts of the ignition system
when the engine is running.
1
12 agria Verticutter 8200-V6R
1. Safety Instructions
b = 430 mm
h = 660 mm
l = 740 mm
S = 685 mm
H = 1020 mm
L = 1450 mm
Dimensions
Explanation of Signs
Wear individual protective ear
plugs.
Wear protective gloves.
Wear solid shoes.
1
Explanation of Warning Symbols
Before doing any cle-
aning, maintenance
and repair work, shut
off the engine and
remove spark plug
connector.
Keep off the knives
while the engine is
running!
Do not touch rotating
machine parts. Wait
until they have come
to a complete stop.
Do not operate the
machine without
guards! Move guards
in place before you
take up operation.
agria Verticutter 8200-V6R 13
2. Specifications
Engine manufacturer: .............Robin
Type:....................................... EH17D
Version:.... Fan-air-cooled 1-cylinder-
4-stroke engine (petrol),
overhead valves
Bore:........................................ 67 mm
Stroke:..................................... 49 mm
Cubic capacity: ................... 172 ccm
Output: ...............4.0kW at 3,600 rpm
Torque: ..... max. 11 Nm at 2,600 rpm
Spark plug:....... Champion WR 7 AC
NGK BR 6 HS
Electrode gap: ..........0.6 mm–0.7 mm
Ignition system:
Contactless electronic solenoid
ignition, ignition point is pre-set, radio
remote screened according to VDE
0879
Valve lash (engine cold):
Intake: .................. 0.08 mm–0.11 mm
Outlet: .................. 0.08 mm–0.11 mm
Starter: ......................... Recoil starter
Cold start system: ..................Choke
Fuel tank capacity:.................... 3.6 l
Fuel: ....................Conventional petrol
octane number min. 85 RON
(refer to fuel recommendations)
Air filter:................. Dry filter element
with foamed pre-filter
Carburetor: .......... horizontal, floating
Mix control screw:
in base setting . approx. 3/8 turn open
Rated speed: .................... 3,600 rpm
Top no-load speed: ......... 3,800 rpm
Idling speed: .................... 1,200 rpm
Engine oil:
Filling quantity .............. approx. 0.65 l
Multi-grade oil SAE 10W-40 API-SC
Working width:........................ 50 cm
No. of knives: ................................ 19
Slitting circumference ........ 220mm Ø
Shaft speed: ..................... 2,500 rpm
Rotational direction of knife shaft:
.. reverse, opposed to travel direction
Slip clutch: ...............between knives
Height adjustment:......Centrally and
steplessly via crank bolt;
fast lift-out mechanism
Discharge: ........................To the rear
Wheels:
Front wheels ...........................23cm Ø
Rear wheels .......................... 23cm Ø
with special ball bearings
Wheel drive: ........... approx. 2.5km/hr
Rear-wheel drive via worm gear with
integrated conus clutch and internally
toothed gearwheel with overrunning
clutch. Engagement is via handle on
steering handle. Oil quantity in
worm gear: approx. 0.2l
SHELL Agroma Multipurpose 15W40 CD
or Harvella TX 10W40
Steering handle: .................. foldable
Noise level............................. L
wa
100
in accordance with EC directive
84/538/EEC
Vibration acceleration value: on
steering handle grip ....a
hwy
= 9.3 m/s
2
in accordance with ISO 5349 at 85% of
rated engine speed with tools at work
Operability on Slopes:
Engine performance (oil level is at top
”max.” mark) on slopes is satisfactory
as long as the operator is still able to
walk on the slope and operate the
verticutter without extraordinary effort.
Weight: ......................... approx. 69 kg
Dimensions: .................. see page 12
2
14 agria Verticutter 8200-V6R
3. Devices and Operating Elements
The verticutter agria type 8200-V6R is
suited for usual operation in horticulture
and turf care.
Engine
The four-stroke petrol engine runs on
commercial petrol (refer to fuel
recommendations).
During the first 20 operating hours
(break-in period) do not operate the
engine at maximum speed.
Even after the break-in period never
operate the engine at higher speed than
is necessary for the work in hand.
I
High engine speed is harm-
ful to any engine and consid-
erably affects its longevity. This
applies especially for no load
operation. Any overspeed (have the
engine roar) can result in immediate
damage.
Cooling System
The engine is fan-cooled. Therefore
keep the grille on the recoil starter and
the cooling fins on the cylinder clean
and free from sucked-in plant trash.
Idling-Speed
Always ensure that idling-speed is
adjusted correctly. At low speeds and
with the speed control lever set to idle,
the engine is supposed to run smoothly
and without run-out.
Air Filter
The air filter purifies the air intake. A
clogged filter reduces engine output.
Ignition System
The engine is equipped with a
maintenance-free, contactless
electronic ignition system. We
recommend to have necessary check-
ups done by an expert only.
Speed Control Lever
The speed control lever (A/3) on the
steering handle steplessy controls
engine speed from min = idling speed
to max = maximum speed.
Engine-shut-off switch
The verticutter is equipped with a shut-
off switch (A/6). This switches the
ignition off (engine off).
Position ”I” = Operation
Position ”0”= Engine off
3
agria Verticutter 8200-V6R 15
3. Devices and Operating Elements
Knife Shaft Drive
The machine is equipped with a V-belt
clutch with pulley fitted between engine
and knife. Actuation is via the handle
(A/5).
0 = Handle is moved to the rear
I = Handle is moved forward and
knife shaft starts rotating
I
Do not actuate the handle at
high engine speed because this
will quickly ruin the V-belt. Ensure the
V-belt is adjusted properly. See
instructions!
W
Do not tie down this handle.
Knife Shaft
19 knives are arranged around the
shaft. They are bolted to the shaft at a
pretension of 15 Nm (1.5mkg).
l
This pretension generates axial
friction force which drives the knives.
Pretension must not exceed 15 Nm to
ensure the slip clutch engages when
the machine hits a stone or another
obstacle.
Wheel drive
Wheel drive is via a worm gear with
integrated conus clutch and internally
toothed gearwheel with overrunning
clutch on the rear wheels.
Engagement/disengagement is via
handle (A/4).
Wheel drive engagement
Move the handle to the steering hand-
le to position ”I”
– The verticutter moves forward
Wheel drive disengagement
Release the handle which will go to
position ”0”
– You can now push or pull the
verticutter.
W
Do not tie down this handle.
3
16 agria Verticutter 8200-V6R
3. Devices and Operating Elements
Setting the Slitting Depth
W
Ensure the engine is shut off
and the shaft has stopped.
l
Park the verticutter on level ground
and turn the knob (A/15 on the knife
shaft housing) to set the slitting depth
in such a way that the knives barely
touch the ground.
l
Tur n the knob (A/15) to set the desi-
red slitting depth – one turn corre-
sponds to about 1mm depth adjustment
l
The proper slitting depth is 2 mm –
3 mm
Fast Lift-Out
W
Ensure the engine is shut off
and the shaft has stopped.
Use the fast lift-out mechanism to bring
the verticutter in transport position to
prevent the knives from being damaged
when transporting the verticutter on
paved paths or concrete tiles.
Transport Position:
l
Pull the grip-handle of the fast lift-
out mechanism (A/7) all the way out
l
Press on the steering handle
l
Release the grip-handle and press
on the steering handle until the height
adjustment mechanism locks into
transport position
Working Position:
l
Pull the grip-handle of the fast lift-
out mechanism (A/7) all the way out
l
Push up the steering handle
l
Release the grip-handle and
continue pushing up the steering hand-
le until fast lift-out mechanism locks into
working position.
3
agria Verticutter 8200-V6R 17
4. Commissioning and Operation
I
Caution: For reasons of
transport, the machine is
not filled with engine oil!
Before you operate the engine the
first time, fill in engine oil!
Commissioning the
Machine
Please note that engine longevity and
operational reliability depend to a large
extent on its breaking-in. Always allow
a cold engine to warm up for some
minutes and never operate it at full
throttle at the beginning. Make sure the
air filter is serviced regularly and to use
clean fuel.
Please note: for the first 20 hours of
operation (break-in period) do not use
the engine at full power.
For this purpose, park the verticutter
in such a way that the engine is level.
For the proper oil filling quantity and
quality see ”Specifications”.
Check the oil level after filling.
Check oil level
l
Remove the oil plug and clean the
dipstick with a clean cloth. Push the
dipstick back into the oil reservoir (do
not screw it down). Remove the oil
dipstick and read the oil level.
l
If the oil level is below the bottom
notch on the stick, top up engine oil
(see specifications), filling it to the rim
of the oil filler neck.
l
Screw down the plug and tighten it.
Ensure that the plug sits tight in the oil
filler neck when the engine is running.
Before each start:
l
Check the engine oil-level (see
illustration) and top up oil, if necessary
– do not add too much oil!
l
Check whether the fuel tank
contains enough fuel.
Do not fill the fuel tank until the fuel
overflows. Leave enough approx. 5 mm
for the fuel to expand.
W
Be careful when dealing with
fuel. Great danger of fire!
Never refill fuel close to open fire,
inflammable sparks or hot engine
parts. Do not refill fuel in closed
rooms. Refill only with the engine
shut off and cooled down.
Do not smoke
when refilling!
Do not spill any
fuel, use a proper
filling device.
W
Do not start the engine in
closed rooms. Exhaust fu-
mes contain carbon monoxide which
acts toxic when inhaled.
Keep your feet clear off the knife
shaft housing.
3
18 agria Verticutter 8200-V6R
4. Commissioning and Operation
Starting the Engine
l
Open the fuel tap (B/9)
l
Engine cold: Pull the CHOKE lever
(C/4)
l
Engine warm: Leave the CHOKE
lever in normal operating position or
move it to ”middle position”
l
Switch the engine-off switch (A/6) to
”I”, operating position
l
Move the speed control lever (A/3)
to approx. 1/3 speed position
l
Pull the starter cord handle (B/4)
until you feel the starter clutch engage.
Then pull hard and fast to start the
engine. After the start, guide the cord
back. Do not let it snap back.
l
Once the engine is started and let it
warm up for a short time. Slowly move
the choke lever to operating position (if
actuated).
1/3
4
agria Verticutter 8200-V6R 19
4. Commissioning and Operation
Shutting off the Petrol
Engine
l
Move speed control lever to idling
speed and let the engine run idling for
a about 30 seconds.
l
Switch the engine-off-switch to
position ”0”
l
Close the fuel tap
I
Note: The engine-off switch
(A/6) also serves as emergency
off-switch. In an emergency release
the handle for instant engine shut-off.
I
If the verticutter is downed for a
long period, do not turn the en-
gine off by pressing the engine-off-
switch. Instead, close the fuel tap and
let the engine run until it comes to a
stop due to lack of fuel. This is to ensure
the carburetor is empty to avoid resin
deposits.
W
Secure the verticutter against
unauthorized use. Remove the
spark-plug connector.
4
66
66
630 sec
20 agria Verticutter 8200-V6R
4. Commissioning and Operation
Verticutter Operation
l
Before slitting can be carried out,
ensure the turf is cut as short as
possible and is swept.
l
Do not operate the verticutter on wet
lawns and in rainy weather.
Before you start operation remove any
obstacles from the area to be slitted.
Watch out for obstacles during work.
l
Set the slitting depth
l
Start the engine (as described in
”Starting Engine”)
W
Check function of engange-
ment of knife shaft drive and
wheel drive engagement - only
operate the machine if these circuits
are working!
l
Wear individual protective ear plugs
and solid shoes
l
Engage the knife shaft drive by
pressing shortly on the steering hand-
le to tilt the machine for the knives to
rotate freely. This is to allow the knife
shaft to pick up full speed (V-belt slip)
l
Engage wheel drive
Before moving off check the immediate
surroundings for children and animals.
Work Speed
For slitting thatched and mossy lawns
it may be desirable to switch the wheel
drive off and push the verticutter by
hand (slowlier than with wheel drive
engaged).
4
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
