Videx 2 Wire Manuale del proprietario

Marca: Videx

Modello: 2 Wire

Categoria: Impianti citofonici

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

ESVK (4000 Series)

Edition 2009

Rev. 1.6

Index

INDEX ........................................................................................................................................................................... 3

ART.4333 ...................................................................................................................................................................... 4

SPEAKER UNIT WITH BUILT-IN CAMERA ..........................................................................................................................................................................................4

ART.125 ........................................................................................................................................................................ 6

CALL EXPANSION MODULE ............................................................................................................................................................................................................6

ART.3181 ...................................................................................................................................................................... 7

DIGITAL INTERCOM FOR VX2300 2 WIRE SYSTEM..........................................................................................................................................................................7

ART.3381 ...................................................................................................................................................................... 9

DIGITAL VIDEOPHONE FOR VX2300 2 WIRE SYSTEM......................................................................................................................................................................9

ART.5488 .................................................................................................................................................................... 12

HANDS FREE VIDEOMONITOR FOR VX2300 .................................................................................................................................................................................12

ART.5188 .................................................................................................................................................................... 16

HANDS FREE INTERCOM FOR VX2300.........................................................................................................................................................................................16

ART.317 ...................................................................................................................................................................... 20

FOUR WAY DISTRIBUTION BOX .....................................................................................................................................................................................................20

ART.318 ...................................................................................................................................................................... 21

TWO WAY PASSIVE DISTRIBUTION BOX .........................................................................................................................................................................................21

ART.2315 .................................................................................................................................................................... 22

BUS BOOSTER AND VIDEO SIGNAL AMPLIFIER..............................................................................................................................................................................22

ART.2301N.................................................................................................................................................................. 23

ENTRANCES EXCHANGER FOR VX2300 DIGITAL SYSTEMS ............................................................................................................................................................23

ART.2305 .................................................................................................................................................................... 24

EXTENSION RELAY FOR VX2300 DIGITAL SYSTEMS .....................................................................................................................................................................24

ART.2380 .................................................................................................................................................................... 25

INTERFACE “2 WIRE” TO “4+1” AUDIO SYSTEM ...........................................................................................................................................................................25

ART.2321-2321/P ........................................................................................................................................................ 27

POWER SUPPLIES FOR VX2300...................................................................................................................................................................................................27

ART.2322 .................................................................................................................................................................... 28

POWER SUPPLY CONVERTER FROM BUS LINE TO 12 VDC ............................................................................................................................................................28

GENERAL DIRECTIONS FOR INSTALLATION ............................................................................................................ 29

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.4/44

25/11/2009 Rev.1.6

Art.4333

Speaker unit with built-in camera

Fig.1 Fig.2

DESCRIPTION

Speaker unit module with built-in B&W camera with autoiris lens comprised of IR illumination LEDs. According to the speaker unit version it includes one

or two call push buttons. The module is available also in colour camera version where the illumination LEDs are white light.

The unit circuitry incorporates :

The transmitting amplifier with condenser microphone and volume control;

The receiving amplifier with volume control;

The audio balance circuit with the “BALANCE” control;

The enslavement relay to enable the electric lock (3 contacts: common, normally open and normally closed). It can work also as capacitor discharge

to supply directly the electric lock;

The call buttons from 1 to a maximum of 2 depending on the module version;

The illumination LEDs for the card name holder;

The camera comprised of illumination LEDs.

Module Details:

a. Camera with illumination LEDs;

b. Loudspeaker;

c. Card name holder;

d. Call push button (1 or 2 according to the model);

e. Operation LEDs

f. Microphone;

g. Microphone volume control;

h. Balance Control;

i. Loudspeaker volume control;

j. Dip-switch to carry out the following programming:

- Door station ID (switches from 1 to 3);

- Door opening time (switch 4);

- Conversation time (switch 5);

k. System connection terminals;

AVAILABLE MODULE VERSIONS

Art.4333-1, 4333-1/color

Art.4333-1D, 4333-1D/color

BUTTONS LAYOUT

Art.4333-1, 4333-1/color Art.4333-1D, 4333-1D/color

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.5/44

25/11/2009 Rev.1.6

FRONT LEDS SIGNALLING DESCRIPTION

Sign Description

When illuminated, indicates that it is not possible to make a call because a call or a conversation is in progress (from the out-

door station from which you are calling or from another outdoor station on systems with multiple entrances). The LED will be

off when the system is in stand-by

If illuminated, indicates that the call from the outdoor station is in progress. The LED will switch OFF when the call is an-

swered or after the programmed number of rings.

If illuminated, indicates that it is possible to speak because the call has been answered. The LED will switch OFF at the end

of a conversation (or at the end of the conversation time).

If illuminated, indicates that the door lock has been operated. It will switch OFF at the end of the programmed “door opening”

time.

PROGRAMMING

The programming consists of the following settings:

- Unit ID (1..8);

- Door Opening Time (3 or 6 seconds);

- Conversation Time (1 or 2 minutes);

The settings are carried out trough the 6 way dip-switch (reference j on figure 2) accessible from the rear side of the module. The switch 6 is not used.

Unit ID

Switches

1 2 3

OFF OFF OFF 1

ON OFF OFF 2

OFF ON OFF 3

ON ON OFF 4

OFF OFF ON 5

ON OFF ON 6

OFF ON ON 7

ON ON ON 8

Door Opening Time

Switches

Seconds

OFF 3

ON 6

Conversation Time

Switches

Minutes

OFF 1

ON 2

SIGNALS ON SYSTEM CONNECTION TERMINALS

Terminal Description Terminal Description

BUS NO Door open relay normally open contact

BUS

Bus connection terminals

C Door open relay normally closed contact

PTE “Push to exit” active low input +C Electric lock capacitor discharge output

GND Ground

VAUX

35Vdc power supply input (if used, the module is powered

locally and not from the BUS)

GND Ground NC Door open relay normally closed contact

To use the electric lock with capacitor discharge, make a short between “C” and “+C” then connect the electric lock between terminals “NO”

and “GND”.

UNIT SPECIFICATION

Housing/Mounting

One 4000 Series Module / 4000 Series Modular System

Push Buttons

Yes, from 0 to 2 call buttons according to the model

Programming

Yes, carried out by the 6 way dip-switch located on the rear of the module

Controls

Microphone and Loudspeaker volume trimmers plus balance trimmer

Front plate Finishes

Mirror stainless steel (standard) and Anodized aluminium (add /a after the product code)

Power Supply

Supplied by the BUS line

Working Temperature

-10 +50ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers UK Customers

VIDEX Electronics S.p.A.

www.videx.it

– [email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all

member states of the EU with no restrictions.

This product follows the provisions of the European Directives

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribui-

to liberamente all’interno dei paesi membri dell’unione europea EU.

Questo prodotto è conforme alle direttive Europee

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.6/44

25/11/2009 Rev.1.6

Art.125

Call expansion module

Fig.1

DESCRIPTION

This module must be used in combination with speaker units Art.4333 with firmware release 2.0 or higher. The module, in combination with standard

4000 series button expansion modules (Art.4842, 4843, 4844 and 4845), allows to add up to 5 call buttons to the call buttons built-in the speaker unit to

reach a maximum of 7 call buttons. To supply the LED of the button expansion modules make the connection as shown in figure 1.

UNIT SPECIFICATION

Housing/Mounting

5 resistors module / fix to button expansion module

Push Buttons

N/A

Programming

N/A

Controls

N/A

Power Supply

N/A

Working Temperature

-10 +50ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers UK Customers

VIDEX Electronics S.p.A.

www.videx.it

– [email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all

member states of the EU with no restrictions.

This product follows the provisions of the European Directives

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribui-

to liberamente all’interno dei paesi membri dell’unione europea EU.

Questo prodotto è conforme alle direttive Europee

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.7/44

25/11/2009 Rev.1.6

Art.3181

Digital intercom for VX2300 2 Wire System

Fig.1 Fig.2

DESCRIPTION

Intelligent intercom with “door open/intercommunicating call” push button (key), bus relay (Art.2305) activation button (dot), “privacy ON-OFF” switch,

“door open” and “privacy on” LEDs and call tone volume control (3 levels). To reduce bus current all apartment devices are in a sleep mode when not

used. In case a user forgot to replace the handset, each operation must be executed within 10 seconds of lifting the handset otherwise the handset re-

turns to its sleep state. To then perform an operation it would be necessary to hang up the handset and pick it up again.

PUSH BUTTONS, LEDS AND CONTROLS (FIG.1)

a Door open push button – Intercommunicating call. For an intercommunicating call, pick up the handset and press as many times as the

extension or address value to call (see SW3 Intercommunication Settings).

b Activate bus relay board Art.2305 push button. To activate a bus relay pick up the handset and press as many times as the address

value of the relay.

c Door Open LED. Switched ON if the door is open. Its operation depends on additional connections.

d Privacy ON LED. Switched ON when the privacy service is active

e Privacy ON-OFF switch. The privacy duration time can be programmed. If the intercom is programmed for a specific privacy duration,

after the service is enabled to “ON” (red LED ON), the service will automatically turn off when the time expires.

f Call tone volume control (3 levels)

DIP-SWITCHES AND JUMPERS (FIG.2)

SW1 Switches from 1 to 7 are used for unit address (from 1 to 127 binary coded). Last switch (8) is not used

SW2 Switches 1,2 and 3 are used to set privacy duration time. Switch 4 is not used.

SW3 Switches 1,2 and 3 are used to for intercommunication settings. Switch 4 is not used.

S1 Impedance terminator. The jumper must be normally closed. When more videophones/intercoms are connected in parallel (from a pe-

ripheral to another and so on until the last) the jumper must be open for all the intercoms except for the last following the connection or-

der.

PROGRAMMING

After each programming operation carried out through dip-switches or jumpers it is necessary to temporary disconnect the phone from the BUS or from

the power supply if locally powered.

SW1 – INTERCOM ADDRESS

Switches Status Binary Code – Decimal Value

7 6 5 4 3 2 1 64 32 16 8 4 2 1

Decimal

Code

OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 1 1

OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 1 0 2

OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 1 1 3

OFF OFF OFF OFF ON OFF OFF 0 0 0 0 1 0 0 4

OFF ON OFF OFF ON OFF ON 0 1 0 0 1 0 1 37

ON ON OFF OFF OFF ON ON 1 1 0 0 0 1 1 99

The table above shows how to set the address of the phone. Considering that ON = 1 and OFF = 0, multiply each digit for the relevant decimal weight

then add values obtained to get the address: E.g. as highlighted in the table OFF,ON,OFF,OFF,ON, OFF,ON in binary is equal to 0100101 then adding

each digit for the relevant decimal weight you obtain the address 37.

Note

The maximum number of units allowed is 100 but the address of each unit can be a value between 1 and 127

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.8/44

25/11/2009 Rev.1.6

SW2 – PRIVACY DURATION TIME

Switches Status

4 3 2 1

Privacy Mode

(switch 1)

Privacy Duration

(switches 2,3)

OFF OFF 15 minutes

OFF ON 1 hour

ON OFF 4 hours

ON ON

OFF

The privacy duration time is set by switches 2 and 3. When enabled the privacy ser-

vice will be disabled when the set time expires or the switch is moved back to off.

8 hours

No privacy time expiration: the privacy service is enabled or disabled only by the

slide switch.

SW3 – INTERCOMMUNICATION SETTINGS

Switches Status

4 3 2 1

Intercommunication Mode

(switch 1)

Videophone

Extension

(switches 2,3)

OFF OFF 1 (master)

OFF ON 2 (slave)

ON OFF 3 (slave)

ON ON

OFF

Intercommunication allowed between videophones (same unit address) inside the

same flat. To call an extension pick up the handset then press the “door open” button

as many times as the extension value (Eg. extension 2 two times, 3 three times etc).

Each intercom/videophone in the same apartment must have a different exten-

sion address, the master address must always be set except when one of the

intercom/videophone is set for apartment intercommunication (i.e. in a 3 inter-

com/videophone installation, one of the intercom/videophone must have the

extension address 1 while the others must have different addresses)

4 (slave)

OFF OFF ON

Intercommunication allowed between videophones (different apartment). To call an

extension pick up the handset then press the “door open” button as many times as

the address value (Eg. extension 10 ten times, 12 twelve times etc)

On installations where there are more than one intercom/videophone in the same apartment and intercommunication between different

apartments is required, only one intercom/videophone may be set with this function (SW3.1=ON, SW3.2=OFF, SW3.3=OFF). The other inter-

com/videophones in the apartment must be set for local intercommunication with extension addresses “2-4” (slaves). From the inter-

com/videophone set for intercommunication with other apartments it will be not possible to intercommunicate within the apartment but slave

extensions 2-4 will be able to intercommunicate with each other.

NUMBER OF RINGS

The number of rings can be set to 3 (factory preset) or 6.

To change the number of rings proceed as follow:

- Disconnect the power supply from the system;

- Short the terminals “LB” and “GND”;

- Reconnect the power supply to the system checking the privacy on LED and then remove the short between terminals “LB” and “GND”;

- The number of LED flashes will be 1 for 3 rings or 2 for 6 rings.

Each time this operation is carried out the number of rings is switched between the values 3 and 6.

SIGNALS ON CONNECTION TERMINALS

Signal Description

BUS

Bus contacts

LED-

Door open LED ground signal input

LED+

Door open LED power supply input (+12Vdc)

GND

Ground signal

GND

Ground signal

Alarm input (not implemented)

Local Bell contact (put a push button between this terminal and the relevant GND terminal)

SPECIFICATION

Housing/Mounting

3000 Series Intercoms / direct wall mounting

Push Buttons

Yes, two

Programming

Yes, carried out by the dip-switches inside the intercom

Controls

Call tone volume and privacy ON-OFF switch

Power Supply

Supplied by the BUS line

Working Temperature

-10 +50ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers UK Customers

VIDEX Electronics S.p.A.

www.videx.it

– [email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all

member states of the EU with no restrictions.

This product follows the provisions of the European Directives

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribuito

liberamente all’interno dei paesi membri dell’unione europea EU.

Questo prodotto è conforme alle direttive Europee

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.9/44

25/11/2009 Rev.1.6

Art.3381

Digital videophone for VX2300 2 Wire System

Fig.1 Fig.2

DESCRIPTION

Intelligent videophone with 4” flat screen B&W monitor with “door open” and “camera recall” push buttons, bus relay enable button, service button, “pri-

vacy ON-OFF” button plus “privacy on” and “door open” LEDs. Controls: 3 levels of call tone volume (both main and local) plus contrast and brightness.

The videophone is available also in colour version Art.3481 which uses a 3,5” active matrix LCD monitor. To reduce bus current all apartment devices

are in a sleep mode when not used. In case a user forgot to replace the handset, each operation must be executed within 10 seconds of lifting the

handset otherwise the handset returns to its sleep state. To then perform an operation it would be necessary to hang up the handset and pick it upagain.

PUSH BUTTONS, LEDS AND CONTROLS (FIG.1)

a Door open push button – Intercommunicating call. For an intercommunicating call, pick up the handset and press as many times as the

extension or address value to call (see SW3 Intercommunication Settings).

Camera recall push button. Pick up the handset and press as many times as the DEVICE N. of the door station to switch on. b

If the door station uses the Art.4303N plus the Art.4330N, pressing this button during a conversation switches the video signal coming

from the camera module to the video signal coming from the camera module input for external camera.

c Activate bus relay board Art.2305 push button. To activate a bus relay pick up the handset and press as many times as the address

value of the relay.

d Service push button.

e Privacy ON-OFF push button. The privacy duration time can be programmed.

f Privacy ON LED. Switched ON when the privacy service is active.

g Door Open LED. Switched ON if the door is open. Its correct operation depend from correct connection (terminals 1 and 18)

h Call tone volume control (3 levels)

i Contrast control (left decrease, right increase)

l Brightness control (left decrease, right increase)

DIP-SWITCHES AND SWITCHES (FIG.2)

SW1 Switches from 1 to 7 are used for unit address (from 1 to 127 binary coded). Last switch (8) is not used

SW2 Switches 1,2 and 3 are used to set privacy duration time. Switch 4 is not used.

SW3 Switches 1,2 and 3 are used for intercommunication settings. Switch 4 is used to set the slave mode.

SW Impedance terminator. The standard position is “close”. When more videophones are connected in parallel (from a videophone to an-

other and so on until the last) it must be set to “open” for all the videophones except for the last following the connection order.

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.10/44

25/11/2009 Rev.1.6

PROGRAMMING

After each programming operation carried out through dip-switches or jumpers it is necessary to temporary disconnect the videophone from the BUS or

from the power supply if locally powered.

NUMBER OF RINGS

The number of rings can be set to 3 (factory preset) or 6.

To change the number of rings proceed as follow:

- Unplug the flat cable from the pcb connection board;

- Put in short the terminals 13 and 14;

- Plug-in the flat cable checking the privacy on LED and remove the short between terminals 13 and 14;

- The number of LED flashes will be 1 for 3 rings or 2 for 6 rings.

Each time this operation is carried out the number of rings is switched between the values 3 and 6.

SW1 – VIDEOPHONE ADDRESS

Switches Status Binary Code – Decimal Weight

7 6 5 4 3 2 1 64 32 16 8 4 2 1

Address

OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 1 1

OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 1 0 2

OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 1 1 3

OFF OFF OFF OFF ON OFF OFF 0 0 0 0 1 0 0 4

OFF ON OFF OFF ON OFF ON 0 1 0 0 1 0 1 37

ON ON OFF OFF OFF ON ON 1 1 0 0 0 1 1 99

The table above shows how to set the address of the videophone. Considering that ON = 1 and OFF = 0, multiply each digit for the relevant decimal

weight then sum values obtained to get the address: E.g. as highlighted in the table OFF,ON,OFF,OFF,ON, OFF,ON in binary is equal to 0100101 then

multiplying each digit for the relevant decimal weight you obtain the address that is 37.

Note

The maximum number of units allowed is 100 but the address of each unit can be a value between 1 and 127.

SW2 – PRIVACY DURATION TIME

Switches Status

Privacy Mode

(switch 1)

Privacy Duration

(switches 2,3)

4 3 2 1

OFF OFF 15 minutes

OFF ON 1 hour

ON OFF 4 hours

ON ON

OFF

The privacy duration time is set by switches 2 and 3. When enabled the privacy ser-

vice is disable when the time set expires or the relevant button is pressed again.

8 hours

No privacy time expiration: the privacy service is enabled or disabled only by the pri-

vacy button.

SW3 – INTERCOMMUNICATION SETTINGS

Switches Status

4 3 2 1

Intercommunication Mode

(switch 1)

Videophone

Extension

(switches 2,3)

OFF OFF 1 (Master)

OFF ON 2 (Slave)

ON OFF 3 (Slave)

ON ON

OFF

Intercommunication between videophones in the same apartment. To call an exten-

sion pick up the handset then press the “door open” button as many times as the ex-

tension (Eg. extension 2 two times, 3 three times etc). Each intercom/videophone

must have a different extension address, the master address must always be

set (i.e. in a 3 intercom/videophone installation, one of the inter-

com/videophone must have the extension address 1 while the others must

have different addresses included from 2 to 4)

4 (Slave)

OFF OFF ON

Intercommunication between videophones in different apartments. To call an exten-

sion pick up the handset then press the “door open” button as many times as the ad-

dress (Eg. extension 10 ten times, 12 twelve times etc)

Slave Mode (switch 4) for Extensions 2, 3 and 4

OFF Factory preset, during a call the slave videophones will only ring while the master will also show the video picture). The picture will only

appear on the slave when answered.

ON During a call, the videophone will ring and show the video picture: in this case the videophone must be powered locally using an Art.2321

and connecting BUS+ to “Vin” (9) and BUS- to “–“ (10).

NOTE: Extension 1 is mandatory. On systems with more than one device in an apartment, each device must have a unique extension ID.

On installations where there are more than one intercom/videophone in the same apartment and intercommunication between different

apartments is required, only one intercom/videophone may be set with this function (SW3.1=ON, SW3.2=OFF, SW3.3=OFF). The other inter-

com/videophones in the apartment must be set for local intercommunication with extension addresses “2-4” (slaves). From the inter-

com/videophone set for intercommunication with other apartments it will be not possible to intercommunicate within the apartment but slave

extensions 2-4 will be able to intercommunicate with each other.

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.11/44

25/11/2009 Rev.1.6

VIDEOPHONE CONNECTION BOARD ART.3980

As 3000 series videophones also this version uses the Art.3980 connection board.

Fig.3

SIGNALS ON TERMINALS OF ART.3980 CONNECTION BOARD

Terminal Signal Description

1 -LD

Door open LED ground signal input

2 AL

Alarm input (not implemented)

3 S

4 S

Contacts for “S” service push button. Linked together when the button is pressed

5 GND

Ground signal

9 Vin

10 -

Auxiliary power supply input (for local power supply)

11 BUS

12 BUS

Bus contacts

13 -

14 LB

Local bell contacts

18 +LD

Door open LED power supply (12Vdc)

SPECIFICATION

Housing/Mounting

3000 Series Videophones / mounting plate plus connection board

Push buttons

Yes, 5

Programming

Yes, carried out by the dip-switches located on the rear of the videophone

Controls

Call tone volume, contrast and brightness

Power Supply

Supplied by the BUS line

Working Temperature

-10 +50 ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers UK Customers

VIDEX Electronics S.p.A.

www.videx.it

– [email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all

member states of the EU with no restrictions.

This product follows the provisions of the European Directives

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribuito

liberamente all’interno dei paesi membri dell’unione europea EU.

Questo prodotto è conforme alle direttive Europee

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.12/44

25/11/2009 Rev.1.6

Art.5488

Hands Free Videomonitor for VX2300

164

130,00

Fig.1 Fig.2

DESCRIPTION

An intelligent Hands-free (surface or flush mounting) video monitor employing a colour 3.5” active matrix LCD display, with push buttons for “door

open/intercommunicating call”, “answer/camera recall”, “privacy on/off”, “BUS relay activation” and 2 service buttons plus 4 LED’s associated with 4

main buttons. In addition to the above the unit has controls for loudspeaker volume, call tone volume, brightness and hue with programmable number of

rings, privacy duration and intercommunication mode.

PUSH BUTTONS, LEDS AND CONTROLS (FIG.1)

Service push button - When pressed, shorts terminal “S1” to terminal “GND” (ground).

Bus Relay Button to Activate bus relay board Art.2305. To activate a bus relay press as many times as the address value of the relay.

Answer button - On an incoming call, operation of this button allows the user to answer and converse with the visitor. LED 2 will illumi-

nate.

Camera recall button - Press as many times as the DEVICE N. of the door station to switch on.

Switch off button - With the system switched on (monitor on), momentary operation of the button will switch the video monitor off. The

videomonitor will also automatically switch off after a time delay if the button is not pressed. LED 2 will switch off.

Simplex button - Pressing and holding the button for more than 3 seconds will switch the videomonitor into SIMPLEX speech mode.

Press and hold the button to speak to the caller (LED 2 will flash rapidly), release the button to listen (LED 2 will flash slowly). If the but-

ton is not pressed for 10 seconds the videomonitor will switch off. The videomonitor will revert to duplex speech when another call is

made.

When pressed, shorts terminal “S2” to Terminal “GND” (ground).

Privacy on-off button:

− If the monitor is switched on, press and keep pressed this button for more than 3 seconds to enable/disable the service. The relative

LED will illuminate when the privacy service is enabled.

− If the monitor is switched off, keep this button pressed together with the “speak” button

until the privacy LED switches ON.

Camera select button - With a conversation in progress, press to switch from door station camera to external camera (requires Art.4330N

and external camera) and viceversa.

Intercommunicating call button - For an intercommunicating call, when the videomonitor is in stand-by, press as many times as the ex-

tension or address value to call.

Door open button - During a call, operation of this button will activate the “door open” relay (NO1, NC1, COM1). LED 4 will illuminate if

terminal 6 has been connected to a door contact.

LED for programming purposes

LED relating to the operation of the answer/switch off/camera recall/simplex button

LED relating to the operation of privacy button

LED relating to the operation of door open button(powered from the connection terminal “6” of Art.5980)

Loudspeaker volume control

Call tone volume control

Brightness control

Colour intensity control

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.13/44

25/11/2009 Rev.1.6

PROGRAMMING

The videomonitor setup consists of the following settings:

- Number of Rings;

- Melody selection;

- Unit address (1..127, switches 1 to 7 of SW1);

- Bus Termination (open or close, switch 8 of SW1);

- Intercommunication mode (between apartments or within apartment switch 1 of SW3);

- Extension address (1..4, switches 2,3 of SW3);

- Slave mode (switch 4 of SW3);

- Privacy duration (switches 1,2 and 3 of SW2)

The programming of the number of rings and melody are carried out through the videomonitor push buttons , all other settings are carried out on the

three dip-switch banks (SW1, SW2 and SW3) on the rear side of the video monitor.

Except the number of rings programming, it is necessary to remove temporary the power supply after making any other programming

changes.

NUMBER OF RINGS AND MELODY SELECTION

First of all make a camera recall to switch on the unit then proceed with the programming operation.To alter the number of rings and select the melody,

the videomonitor must be in program mode. This is achieved by operating the two following buttons at the same time (left button of the volume control

and the right button of the colour intensity control) see Fig.1A 8 small buttons towards the bottom of the face plate (far left button and far right button

together). When the programming mode is entered LED 1 (Fig.1A) starts flashing. This will automatically reset after 20 seconds of idle time.

Number of rings

− When in the programming mode press and hold the “

” button, LED 1 will stop flashing and LED 3 (Fig.1A) will start to flash showing the number of

rings (each flash = 1 ring i.e. 6 flashes = 6 rings)

− Once the value of rings has been reached release the “

” button.

− Wait approx 10 seconds for LED 1 to stop flashing to signal that the new value is stored and program mode has exited.

Melody selection

− When in the programming mode, press left or right call tone volume control buttons

(press the left button to navigate backward or the right button

to navigate forward in the melodies selection menù) until the videomonitor plays the selected melody (during the melody play the LED1 stops flash-

ing);

− Before press again one of the two buttons to select previous (left button) or next (right button) melody, wait for LED1 starts flashing again then press

and hold pressed one button until the selected melody is played;

− Once reached the required melody, Wait approx 10 seconds for LED 1 to stop flashing to signal that the new value is stored and program mode has

exited.

Notes

The second melody increases its volume at each ring: first ring starts at minimum volume level up to the maximum volume level on the last ring. Are

available 4 levels of volume: if are set 6 rings, the fourth, the fifth and the sixth will be emitted at the maximum volume level.

VIDEOMONITOR ADDRESS – SW1.1..7

The table above shows how to set the address of the videophone. Considering that ON = 1 and OFF = 0, multi-

ply each digit for the relevant decimal weight then sum values obtained to get the address: E.g. as highlighted

in the table OFF,ON,OFF,OFF,ON, OFF,ON in binary is equal to 0100101 then multiplying each digit for the

relevant decimal weight you obtain the address that is 37.

Switches Status Binary Code – Decimal Weight

7 6 5 4 3 2 1 64 32 16 8 4 2 1

Ad-

dress

OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 1 1

OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 1 0 2

OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 1 1 3

OFF OFF OFF OFF ON OFF OFF 0 0 0 0 1 0 0 4

OFF ON OFF OFF ON OFF ON 0 1 0 0 1 0 1 37

ON ON ON ON ON ON ON 1 1 1 1 1 1 1 127

Note

The maximum number of units allowed is 100 but the address of each unit can be a value between 1 and 127.

BUS TERMINATION - SW1.8

The factory preset for this switch is ON: termination enabled. In case of more units (intercoms, videophones or

video monitors) in a parallel connection (bus wires are connected to the terminals of the first unit then from this

to the second and so on up to 4 units max) switch 8 must be set to ON only for the last unit in the chain while

on all other units must be set to OFF (bus termination disabled).

INTERCOMMUNICATION MODE – SW3.1

This switch establishes the intercommunication mode: in OFF position (default) intercommunication is between

units in the same apartment (same addresses but different extension); in ON position the intercommunication is

between units in different apartments (different addresses).

On installations where there are more than one intercom/videophone in the same apartment and intercommunication between different

apartments is required, only one intercom/videophone may be set with this function (SW3.1=ON, SW3.2=OFF, SW3.3=OFF). The other inter-

com/videophones in the apartment must be set for local intercommunication with extension addresses “2-4” (slaves). From the inter-

com/videophone set for intercommunication with other apartments it will be not possible to intercommunicate within the apartment but slave

extensions 2-4 will be able to intercommunicate with each other.

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.14/44

25/11/2009 Rev.1.6

EXTENSION NO – SW3.2..3

If the intercommunication between apartments is enabled (switch 1 of SW3 = ON) leave these two switches in default position (both to OFF). Otherwise,

if the intercommunication is between the same apartment (switch 1 of SW3 = OFF), set the extension addresses starting always from 1. During the ex-

ternal call, all video monitors in the same flat will ring but the video will be shown only from the videmononitor with extension address 1.

2 3 Extension No.

OFF OFF 1 (default, master)

ON OFF 2 (slave)

OFF ON 3 (slave)

ON ON 4 (slave)

SLAVE MODE - SW3.4

This set up concerns the answering mode of the video monitor when there is more than one unit (max 4) in the

same apartment. OFF (default) = during a call, only the video monitor with extension 1 (master) will show the

video. ON = the video monitor will be switched on independently of the extension address: in this case the

video monitor must be supplied locally using a power supply Art.2321 and connecting respectively BUS+ to

terminal 14 and BUS- to terminal 11 of the pcb connection board provided with the Art.5980.

PRIVACY UNLIMITED – SW2.1

If this switch is set to OFF (default), the privacy duration is defined by switches 2 and 3.If this switch is set to

ON, the privacy duration is unlimited and the service can be enabled or disabled only by the privacy button.

PRIVACY DURATION – SW2.2..3

This set up requires that switch 1 is set to OFF.

2 3 Duration

OFF OFF 15 minutes

ON OFF 1 hour

OFF ON 4 hours

ON ON 8 hours

VIDEOMONITOR CONNECTION BOARD ART.5980

Fig.3

SIGNAL ON CONNECTION TERMINALS

Terminal Signal Description

1 GND

Ground

2 BUS1

Bus input

4 BUS2

Bus input

5 S1 Terminal controlled by the S1 button, close to GND until the button is pressed

6 LED

Auxiliary LED power supply input (12Vdc)

7 S2 Terminal controlled by the S2 button, close to GND until the button is pressed

8 GND

Ground

9 GND

Ground

10 LB

Local bell input (active low)

11 GND

Ground

14 +VAUX

Auxiliary power supply input (to be used when the switch 4 of SW3 is set to ON)

18 AL

Alarm input (not implemented yet)

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.15/44

25/11/2009 Rev.1.6

VIDEOMONITOR WALL MOUNTING INSTRUCTIONS

Fig.1 Fig.2

Fig.3 Fig.4

- Cables must be fed through the opening “e” (Fig. 2A) of the mounting plate “c”, which should be fitted approximately 135cm from finished floor level as

shown in Fig 1;

- Place the mounting plate “c” against the wall feeding the wire group “d” through opening “e” of the mounting plate and mark the fixing holes “a” (Fig.

2A)

- Drill the fixing holes “a”, insert the wall plugs “b” then with the cables threaded through opening “e” fix the mounting plate “c” to the wall with the 4

screws provided “f” (Fig. 2A).

- Hook the pcb connection board “g” to the mounting plate “c”as shown in Fig2B and connect the wires (using the screwdriver provided) to the terminals

as shown in the diagram provided;

- Once the wires are connected, hook the videophone “h” to the Mounting plate “c” as shown in Fig. 3.

• Connect the Plug “I” on the ribbon cable from the videophone to the plug “l” on the PCB connection board “g”;

• Place the videophone “h” against the 4 hooks “m” on the mounting plate “c” (in line with the 4 openings “n” on the rear side of the videophone Fig. 4)

and push down as suggested by the pointers in Fig. 3, the videophone will lock into place;

- To remove the videophone, hold it firmly and push the unit in an upward direction until the videophone “h” unlocks from the mounting plate “c”.

SPECIFICATION

Housing/Mounting

5000 Series Videophones / mounting plate plus connection board

Push buttons

Yes, 6

Programming

Yes, carried out by the dip-switches located on the rear of the videophone

Controls

Loudspeake and call tone volume, brightness and hue

Power Supply

Supplied by the BUS line

Working Temperature

-10 +50 ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers UK Customers

VIDEX Electronics S.p.A.

www.videx.it

– [email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all

member states of the EU with no restrictions.

This product follows the provisions of the European Directives

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribui-

to liberamente all’interno dei paesi membri dell’unione europea EU.

Questo prodotto è conforme alle direttive Europee

89/336/EEC & 92/31/EEC (EMC),

73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.16/44

25/11/2009 Rev.1.6

Art.5188

Hands Free Intercom for VX2300

164,00

74,00

23,50

24,50

12345678

SW1

1234

SW3

JP1

Fig.1

DESCRIPTION

PUSH BUTTONS, LEDS AND CONTROLS (FIG.1)

Bus Relay Button to Activate bus relay board Art.2305. To activate a bus relay press as many times as the address value of the relay.

Answer button - On an incoming call, operation of this button allows the user to answer and converse with the visitor. LED 2 will illumi-

nate.

Camera recall button - Press as many times as the DEVICE N. of the door station to switch on.

Switch off button - With the system switched on, momentary operation of the button will switch the unit off. The intercom will also auto-

matically switch off after a time delay if the button is not pressed. LED 2 will switch off.

Simplex button - Pressing and holding the button for more than 3 seconds will switch the intercom into SIMPLEX speech mode. Press

and hold the button to speak to the caller (LED 2 will flash rapidly), release the button to listen (LED 2 will flash slowly). If the button is

not pressed for 10 seconds the intercom will switch off. The intercom will revert to duplex speech when another call is made.

Privacy on-off button:

− If the unit is switched on, press and keep pressed this button for more than 3 seconds to enable/disable the service. The relative LED

will illuminate when the privacy service is enabled.

− If the unit is switched off, keep this button pressed together with the “speak” button

until the privacy LED switches ON.

Intercommunicating call button - For an intercommunicating call, when the intercom is in stand-by, press as many times as the extension

or address value to call.

Door open button - During a call, operation of this button will activate the “door open” relay (NO1, NC1, COM1). LED 4 will illuminate if

terminal 6 has been connected to a door contact.

Programming LED

LED relating to the operation of the answer/switch off/camera recall/simplex button

LED relating to the operation of privacy button

LED relating to the operation of door open button(powered from the connection terminal “2” & GND "1" on the connection board)

Loudspeaker volume control

Call tone volume control

PROGRAMMING

The intercom setup consists of the following settings:

- Number of Rings;

- Privacy duration;

- Melody selection;

- Unit address (1..127, switches 1 to 7 of SW1);

- Intercommunication mode (between apartments or within apartment switch 1 of SW3);

- Extension address (1..4, switches 2,3 of SW3);

- Bus Termination (JP1 jumper on connection board);

Two Wire Videokit ESVK Series

PrtCode:ESVK_ENG_1.6.doc – Pag.17/44

25/11/2009 Rev.1.6

The programming of the number of rings, melody and privacy duration are carried out through the intercom push buttons , all other settings are carried

out on the two dip-switch banks (SW1 and SW3) on the rear side of the video monitor. The BUS termination depends on the position of JP1 on the con-

nection board.

Except for when programming the number of rings, it is necessary to temporarily remove the power supply from the unit after making pro-

gramming changes.

NUMBER OF RINGS, PRIVACY DURATION AND MELODY SELECTION

First of all make a recall to switch on the unit then proceed with the programming operation. To alter the number of rings and select the melody, the in-

tercom must be in program mode. This is achieved by pressing the two following buttons at the same time (left button of the volume control and the right

button of the call tone volume control) see Fig.1.When the programming mode is entered LED 1 (Fig.1) starts flashing. This will automatically reset after

20 seconds of idle time.

Number of rings

− When in the programming mode press and hold the “

” button, LED 1 will stop flashing and LED 3 (Fig.1) will start to flash showing the number of

rings (each flash = 1 ring i.e. 6 flashes = 6 rings)

− Once the value of rings has been reached release the “

” button.

− Wait approx 10 seconds for LED 1 to stop flashing to signal that the new value is stored and program mode has exited.

Privacy duration

− When in the programming mode press and hold the “

” button, LED 1 will stop flashing and LED 3 (Fig.1) will start to flash showing the number of

times the button is pressed (each flash = 15 minutes i.e. 8 flashes = 2 hours )

− Once the duration required has been reached release the “

” button.

− Wait approx 10 seconds for LED 1 to stop flashing to signal that the new value is stored and program mode has exited.

Melody selection

− When in the programming mode, press left or right call tone volume control buttons

(press the left button to navigate backward or the right button

to navigate forward through the melodies selection menù) After each press, the melody will be played (during the melody play the LED1 stops flash-

ing);

− Before pressing again one of the two buttons to select previous (left button) or next (right button) melody, wait for LED1 to start flashing again then

press and hold one button until the selected melody is played;

− Once the required melody is reached, Wait approx 10 seconds for LED 1 to stop flashing to signal that the new value is stored and program mode has

exited.

Notes

The second melody increases its volume at each ring: first ring starts at minimum volume level and adjusts up to the maximum volume level on the last

ring. There are 4 volume levels: Rings after this will all play at full volume.

INTERCOM ADDRESS – SW1.1..7

The table above shows how to set the address of the videophone. Considering that ON = 1 and OFF = 0, multi-

ply each digit for the relevant decimal weight then add values obtained to get the address: E.g. as highlighted in

the table OFF,ON,OFF,OFF,ON, OFF,ON in binary is equal to 0100101 then multiplying each digit for the rele-

vant decimal weight you obtain the address that is 37.

Switches Status Binary Code – Decimal Weight

7 6 5 4 3 2 1 64 32 16 8 4 2 1

Ad-

dress

OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 1 1

OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 1 0 2

OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 1 1 3

OFF OFF OFF OFF ON OFF OFF 0 0 0 0 1 0 0 4

OFF ON OFF OFF ON OFF ON 0 1 0 0 1 0 1 37

ON ON ON ON ON ON ON 1 1 1 1 1 1 1 127

Note

The maximum number of units allowed is 100 but the address of each unit can be a value between 1 and 127.

Set switch 8 to OFF position.