CET LTM60 Manuale del proprietario

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 1

CET

VISUALIZED DIGITAL TIMER

Type:

LTM60

THE INSTRUMENTS OF SERIES LTM ARE DIGITAL

INSTRUMENTS WIDE USABLE IN THE INDUSTRY

FOR THEIR PROGRAMMABLE CHARACTERISTICS

AND THE FLEXIBILITY OF THEIR EMPLOYMENT.

LTM60, TIME TOTALIZER WITH 4 PROGRAMMABLE

TIME SCALES AND A GLOBAL TOTALIZER OF THE

TIME.

GENERAL FEATURES

PROGRAMMABLE PARAMETERS

• Frontal keyboard in polycarbonate (antiscratch, antioil,

antacid).

• IP65 protection degree

• Accessible parameters with key software

• Removable terminals connection.

• Execution DIN 48 x 96.

• Recessed assembly.

• Special retaining brackets.

• 4 Time Scales

• Memory

• Reset Key

• START Input Selection

TECHNICAL CHARACTERISTICS

•

POWER SUPPLY IN ALTERNATE CURRENT

•

POWER SUPPLY IN DIRECT CURRENT

•

POWER SUPPLY TOLERANCE

•

ABSORPTION

•

OPERATING TEMPERATURE

•

CLIMATIC CONDITIONS

•

TIMINGS VISUALIZATION

•

TIMINGS SCALES

•

START INPUT

•

AUXILIARY INPUTS POWER SUPPLY

•

COMMAND IMPUTS

•

PROGRAMMED DATA MEMORY

: Single power 24 - 110 - 230 Vac (50 / 60 Hz).

: Single power 24 Vdc

: +10% - 15%.

: 2 W - 3 VA.

: -5 °C + 55 °C.

: U.R. 95 % at 40 °C (without condensate).

: 6 digits, 14 mm high

: 9999h59m - 99h59m59s - 99m59s99c - 9999s99c

: programmable as Continuous; Impulsive, Start/Stop

: 24 Vdc - 80 mA available on terminals.

: 1 Start - 1 Reset Timing - 1 Inhibit Timing (Inhibit).

: static (without battery)

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 2

DESCRIPTION OF THE FRONTAL KEYBOARD

ø

YELLOW

The key 'LEFT ARROW' in normal operating phase visualizes, blinking, all the programmings executed without the

limitation of the insertion code. The time of scansion of the programmings is given from the pressure of the same

key. It exits automatically from this phase after 5 sec of the last pressure of the same key.

In programming phase it moves the cursor of the figure towards left of a step, than at the beginning it is on the right

side first one on the. At the end it resumes from the first one to right.

ù

YELLOW

The key 'UP ARROW' in normal operating phase it enter and exit to the Totalizer.

In programming phase it increases the value of the blinking figure.

ú

BLUE

The key 'PRG' pressed for 2 sec. allows to enter in the programming phase, visualizing on display C.0000.

In the programming phase, pressing key 'PRG' impulsively, it exits from the programming phase. The instrument

exits automatically from the programming phase, 60 sec. after the pressure of the last key.

û

GREEN

The key 'ENT/RES' in normal phase of counting has the 'RESET' function, with the modalities to it attributed in the

programming phase.

In programming phase it confirms and memorizes the visualized data and passes to the successive function. If it has

arrived to list end it resumes from the beginning.

INPUTS / OUTPUTS DESCRIPTION

DC POWER

(inputs 1-2) 24VDC Power Supply Input of the instrument.

AC POWER

(inputs 3-4) AC Power Supply Input of the instrument; it can be to 24 - 110 - 230 VAC in according to demand.

24 VDC - 80mA

(inputs 5-6) 24 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and amplified

proximity.

START

(inputs 7) START Input that execute the timing starting as the programming mode; it’s configurable in Positive

(PNP) or Negative (NPN) logic by the dip switches on the rear.

RESET

(inputs 8) RESET Input that execute the timing reset; it’s configurable in Positive (PNP) or Negative (NPN) logic

by the dip switches on the rear.

INHIBIT

(inputs 9) INHIBIT Input that execute the timing Inhibit; it’s configurable in Positive (PNP) or Negative (NPN) logic

by the dip switches on the rear.

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key PRG for about 2 sec. On the display appears:

Cod

0000

GROUP 1

:

in order to approach the parameters of group 1, insert code

2357

and press

ENT

SCÄ 1

SCL. = Time Scale. Selection of the maximum time scale of the timing. It’s possible to choose

between 4 different time scales:

1 = 99m59s99c - 2 = 99h59m59s - 3 = 9999h59m - 4 = 9999s99c

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 3

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key PRG for about 2 sec. On the display appears:

Cod

0000

GROUP 2

:

in order to approach the parameters of group 1, insert code

2413

and press

ENT

NeÆon

NeÆoF

Active or excluded memory.

This parameter allows to program the saving of the current counter value during the power off

the instrument.

MEM.on. = memorization of the count during the power off. When power on the instrument the

display will visualize the last present value in the power off phase.

MEM.of. = excluded memorization of the count; every time that the instrument comes powered

off and then powered on the count comes lost and the instrument restart always from the initial

condition.

RreË 0

reË 3

Function of RESET Key ; this programming enable and disable the RESET function of the

RES frontal key during the normal timing:

RES. 0 = RESET function of the RES key disabled

RES. 1 = RESET function of the principal timing only

RES. 2 = RESET function of the global timing only

RES. 3 = RESET function of the principal and global timings

Iæ Á

Iæ »

Iæ Ë

Programming of the START Input.

This programming allows to Start the timing in three different modes:

In. I. = Impulsive Mode; the timing starts with the impulsive closing of the START input.

In. C. = Continuously Mode; the timing starts with the closing of the START input; the timing

is interrupted every time the START input comes opened.

In. S. = Start/Stop Mode; the timing starts with the impulsive closing of the START input and it

stops to the subsequent closing. Closing another time the input the timing resume and it stops

to the subsequent closing.

¹È È

¹È ê

Activation mode of the programmed parameters.

With this programming is possible to activate the executed programmings directly to the exit of

the programming or, when exited of the programming, after a RESET (with frontal key or from

rear input)

A.P. = P. Activation of the parameters to the exit of the programming.

A.P. = r. Activation of the parameters to the exit of the programming after a RESET.

Pressing the key ù the totalizer of time will be visualized for 5 sec.

Toì

0¨0¨00

The totalizer visualizes the total time that the instrument has show.

It can be resetted through frontal key RES or from RESET input when it is visualized on the

display.

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 4

DECLARATION OF ‘CE’ CONFORMITY

CE NORMATIVE CONFORMITY

Borgolavezzaro, October, 03rd 2005

The building firm:

CET s.r.l.

Head office:

Strada Statale 211, Km 53,3

28071 Borgolavezzaro (No) ITALIA

Tel. 0039 - (0)321 - 885301 Fax. 0039 - (0)321 - 885560

declare that the products:

type :

Electronic Timer

model:

LTM 60

use class:

Industrial

are in conformity with the following normatives:

EN55011

ENV50141

ENV50204

EN61000-4-2

EN61000-4-4

The manufacturing:

CET s.r.l.

________________________________

Signature

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 5

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 6

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 7

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.1

LTM 60

Pag. 8

CONNECTIONS

INPUT SIGNALS

START START

CONTACT CONTACT

NPN PNP

START START

TTL LOGIC TTL LOGIC

NPN PNP

PROGRAMMING PROGRAMMING

NPN PNP

RESET INHIBIT

NPN NPN

RESET INHIBIT

PNP PNP

OVERALL DIMENSIONS

FRONT SIDE

REAR DRILL TEMPLATE

CET

CETCET

CET

CETCET

CET

s.r.l.

Strada Statale 211 Km 53,550

28071 Borgolavezzaro - NO - ITALY

Tel : ++39 0321-885180/885301/885807

Fax : ++39 0321-885560

info@cet-italy.com

www.cet-italy.com

Agent :

48

96

ENT

RES

PROG

L1

L2

1ª6«2

5

Electronic counter

LTM

CET

139

115

9

15

44x92

REMOVABLE

TERMINALS

RETAINING

BRACKETS

10

MAX

93

45

7

6

7

5

6

7

5

7

6

8

6

9

5

8

5

9

92

44

1 2 3 4 5 6 7 8 9 10 11 12 13

-

+

24 VDC AC

POWER

+

-

24 Vdc

80mA

RESET

1

2

3

4

5

6

7

9

8

13

START

INHIBIT

11

10

12

CET LTM60 Manuale del proprietario

CET LTM60 Manuale del proprietario

in altre lingue

Documenti correlati