CET NTM51 Manuale del proprietario

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 1

CET

VISUALIZED DIGITAL TIMER

WITH ONE SET POINT

Type:

NTM51

THE INSTRUMENTS OF SERIES NTM ARE DIGITAL

INSTRUMENTS WIDE USABLE IN THE INDUSTRY

FOR THEIR PROGRAMMABLE CHARACTERISTICS

AND THE FLEXIBILITY OF THEIR EMPLOYMENT.

NTM51, TIMER WITH ONE PROGRAMMABLE SET

POINT AND ONE RELAY OUTPUT. MOREOVER, IT’S

AVAILABLE A TOTALIZER OF THE TIME.

GENERAL FEATURES

PROGRAMMABLE PARAMETERS

• Frontal keyboard in polycarbonate (antiscratch, antioil,

antacid).

• IP65 protection degree

• Accessible parameters with key software

• Removable terminals connection.

• Execution DIN 72 x 72.

• Recessed assembly.

• Special retaining brackets.

• One Set Point

• Automatic Time Reset

• 4 Time Scales

• UP / DOWN / SUPERIOR Timing

• Memory

• Reset Key

• START Input Selection

• OUTPUT Mode Selection

TECHNICAL CHARACTERISTICS

•

POWER SUPPLY IN ALTERNATE CURRENT

•

POWER SUPPLY IN DIRECT CURRENT

•

POWER SUPPLY TOLERANCE

•

ABSORPTION

•

OPERATING TEMPERATURE

•

CLIMATIC CONDITIONS

•

TIMINGS VISUALIZATION

•

TIMINGS SCALES

•

START INPUT

•

AUXILIARY INPUTS POWER SUPPLY

•

COMMAND IMPUTS

•

OUTPUT

•

RELAY RESET

•

PROGRAMMED DATA MEMORY

: Single power 24 - 110 - 230 Vac (50 / 60 Hz).

: Single power 24 Vdc

: +10% - 15%.

: 2 W - 3 VA.

: -5 °C + 55 °C.

: U.R. 95 % at 40 °C (without condensate).

: 5 digits, 11 mm high

: 999h59m - 9h59m59s - 9m59s99c - 999s99c

: programmable as Continuous; Impulsive, Start/Stop

: 24 Vdc - 80 mA available on terminals.

: 1 Start - 1 Reset Timing - 1 Inhibit Timing (Inhibit).

: 1 relay with operating contacts; capacity 2A - 250Vac.

: Manual or automatic with excitation time from 0,1 to 99,9

sec.

: static (without battery)

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 2

DESCRIPTION OF THE FRONTAL KEYBOARD

ø

WHITE

The key 'LEFT ARROW' in normal operating phase visualizes, blinking, all the programmings executed without the

limitation of the insertion code. The time of scansion of the programmings is given from the pressure of the same

key. It exits automatically from this phase after 5 sec of the last pressure of the same key.

In programming phase it moves the cursor of the figure towards left of a step, than at the beginning it is on the right

side first one on the. At the end it resumes from the first one to right.

ù

WHITE

The key 'UP ARROW' in normal operating phase it enter and exit to the Totalizer.

In programming phase it increases the value of the blinking figure.

ú

BLUE

The key 'PRG' pressed for 2 sec. allows to enter in the programming phase, visualizing on display C.0000.

In the programming phase, pressing key 'PRG' impulsively, it exits from the programming phase. The instrument

exits automatically from the programming phase, 60 sec. after the pressure of the last key.

û

GREEN

The key 'ENT/RES' in normal phase of counting has the 'RESET' function, with the modalities to it attributed in the

programming phase.

In programming phase it confirms and memorizes the visualized data and passes to the successive function. If it has

arrived to list end it resumes from the beginning.

INPUTS / OUTPUTS DESCRIPTION

DC POWER SUPPLY

(inputs 7 - 8) 24VDC Power Supply Input of the instrument.

AC POWER SUPPLY

(inputs 5 - 6) AC Power Supply Input of the instrument; it can be to 24 - 110 - 230 VAC in according to demand.

24 VDC - 80mA

(inputs 9 - 10) 24 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and amplified

proximity.

START

(input 11) START Input that execute the timing starting as the programming mode; it’s configurable in Positive

(PNP) or Negative (NPN) logic by the dip switches on the rear.

RESET

(input 12) RESET Input that execute the timing reset; it’s configurable in Positive (PNP) or Negative (NPN) logic

by the dip switches on the rear.

INHIBIT

(input 13) INHIBIT Input that execute the timing Inhibit; it’s configurable in Positive (PNP) or Negative (NPN) logic

by the dip switches on the rear.

RL1

(input 1 - 2 - 3) Output of Relay 1, connected to the operation of the Set Point S1. The Common, Normally Open and

Normally Close contacts are available.

DESCRIPTION OF THE LED’s OPERATION

LED 1 It comes activated to the reaching of the Set Points S1.

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 3

SET POINT PROGRAMMING

For SET POINT programming access, proceed as follow:

- Press key ‘PRG’ in impulsive mode; on display appears:

Ë1 <

¨0¨20

S.1 = SET POINT 1, main Set Point, programmable between 1 cent and 999h59m (depending

to the selected scale). If programmed = 0 the Set Point remains excluded and the instrument

works like a totalizer and predisposing the count in UP mode.

Key ENT confirms the data. In order to exit the programming, press key PRG.

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key PRG for about 2 sec. On the display appears:

Cod

0000

GROUP 1

:

in order to approach the parameters of group 1, insert code

2357

and press

ENT

Ìê9²9

t.r. = Time of Automatic Reset, programmable from 0.0 to 99.9 sec. This parameter allows to

make to work the instrument in automatic mode. When the timing arrives to the value of S.1, it

automatically resets the count, excites the RL1 relay and it resumes to count. The RL1 relay

remains excited for the set up time in t.r. If the time of reset is programmed = 0 (0.0) the

instrument gets ready to works in manual mode.

Particular cases: if the set up time t.r. is bigger than the time employed to the timing to arrive

to the values of S.1, the relay will never come unactived.

SCÄ 1

SCL. = Time Scale. Selection of the maximum time scale of the timing. It’s possible to choose

between 4 different time scales:

1 = 9m59s99c - 2 = 9h59m59s - 3 = 999h59m - 4 = 999s99c

Cæ UP

Cæ dæ

Cæ SÈ

Count UP / DOWN / Superior.

Count = Up: Up; the timer gets ready to visualize the timing in increasing way (UP), starting

from zero up to the programmed value of set point. To the end of timing it works in Manual or

Automatic mode, as programmed in t.r. function.

Count = dn: Down; the timer gets ready to visualize the timing in decreasing way (DOWN),

starting from the programmed value of set point to zero. To the end of timing it works in

Manual or Automatic mode, as programmed in t.r. function.

Count = Sp: Superior; the timer gets ready to visualize the timing in increasing way (UP),

starting from zero up to the programmed value of set point. To the end of timing it works in

Manual mode and the timing goes on up to a new command (START, RESET, INHIBIT).

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 4

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key PRG for about 2 sec. On the display appears:

Cod

0000

GROUP 2

:

in order to approach the parameters of group 1, insert code

2413

and press

ENT

NeÆon

NeÆoF

Active or excluded memory.

This parameter allows to program the saving of the current counter value during the power off

the instrument.

MEM.on. = memorization of the count during the power off. When power on the instrument the

display will visualize the last present value in the power off phase.

MEM.of. = excluded memorization of the count; every time that the instrument comes powered

off and then powered on the count comes lost and the instrument restart always from the initial

condition.

RreË 0

reË 3

Function of RESET Key ; this programming enable and disable the RESET function of the

RES frontal key during the normal timing:

RES. 0 = RESET function of the RES key disabled

RES. 1 = RESET function of the principal timing only

RES. 2 = RESET function of the global timing only

RES. 3 = RESET function of the principal and global timings

Iæ Á

Iæ »

Iæ Ë

Programming of the START Input.

This programming allows to Start the timing in three different modes:

In. I. = Impulsive Mode; the timing starts with the impulsive closing of the START input.

In. C. = Continuously Mode; the timing starts with the closing of the START input; the timing

is interrupted every time the START input comes opened.

In. S. = Start/Stop Mode; the timing starts with the impulsive closing of the START input and it

stops to the subsequent closing. Closing another time the input the timing resume and it stops

to the subsequent closing.

Auto Á

Auto ¾

Programming of the Automatic Reset Mode

This parameter allows to activate the timing to the beginning or the end of the programmed

time of the Automatic Reset

.

Auto I. = Activation of the timing to the beginning of the Automatic Reset Time

Auto F. = Activation of the timing to the end of the Automatic Reset Time

0í1 î

0í1 ÷

Programming of the OUTPUT RL1. This parameter allows to activate the RL1 relay

during the timing

î

or at the end

÷

of the timing.

Ou.1.

î

= Activation of the RL1 relay at the end of the timing

Ou.1.

÷

= Activation of the RL1 relay during the timing

¹È È

¹È ê

Activation mode of the programmed parameters.

With this programming is possible to activate the executed programmings directly to the exit of

the programming or, when exited of the programming, after a RESET (with frontal key or from

rear input)

A.P. = P. Activation of the parameters to the exit of the programming.

A.P. = r. Activation of the parameters to the exit of the programming after a RESET.

Pressing the key ù the totalizer of time will be visualized for 5 sec.

Toì

¨0¨00

The totalizer visualizes the total time that the instrument has show.

It can be resetted through frontal key RES or from RESET input when it is visualized on the

display.

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 5

DECLARATION OF ‘CE’ CONFORMITY

CE NORMATIVE CONFORMITY

Borgolavezzaro, October, 03rd 2005

The building firm:

CET s.r.l.

Head office:

Strada Statale 211, Km 53,3

28071 Borgolavezzaro (No) ITALIA

Tel. 0039 - (0)321 - 885301 Fax. 0039 - (0)321 - 885560

declare that the products:

type :

Electronic Timer

model:

NTM 51

use class:

Industrial

are in conformity with the following normatives:

EN55011

ENV50141

ENV50204

EN61000-4-2

EN61000-4-4

The manufacturing:

CET s.r.l.

________________________________

Signature

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 6

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 7

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.1

NTM 51

Pag. 8

CONNECTIONS

INPUT SIGNALS

START START

CONTACT CONTACT

NPN PNP

START START

TTL LOGIC TTL LOGIC

NPN PNP

PROGRAMMING PROGRAMMING

NPN PNP

RESET INHIBIT

NPN NPN

RESET INHIBIT

PNP PNP

OVERALL DIMENSIONS (mm)

FRONT SIDE

REAR

DRILL

TEMPLATE

CET

CETCET

CET

CETCET

CET

s.r.l.

Strada Statale 211 Km 53,550

28071 Borgolavezzaro - NO - ITALY

Tel : ++39 0321-885180/885301/885807

Fax : ++39 0321-885560

info@cet-italy.com

www.cet-italy.com

Agent:

11

10

11

9

10

11

9

11

10

12

10

13

9

12

9

13

72

ENT

RES

PROG

RL1

NTM

36952

è

CET

RL2

electronic timer

113

85

9

19

67

REMOVABLE

TERMINAL

RETAINING

BRACKETS

10

MAX

67

1 2 3 4 5 6 7 8

9 10 11 12 13 14

68

+

-

POWER SUPPLY

VAC 24 VDC

RESET

+

-

24 VDC

START

INHIBIT

1

2

3

4

5

6

7

8

9

10

11

12

13

14

RL1

CET NTM51 Manuale del proprietario

CET NTM51 Manuale del proprietario

in altre lingue

Documenti correlati