BLACK+DECKER BCMW3336 Manuale utente

www.blackanddecker.eu

1

5

9

10

6

10

2

3

4

6

8

7

5

BCMW3318

BCMW3336

2

3

12

13b

13

A

12b

12a

B

12

14

C

4

6

4a

D

BCMW3336

12

C1

BCMW3318

5

3

4

5a

E

2

3

9

F

2

3

1

1a

H

8

8a

8b

G

13

14

I

15

16

17

18

19

20

21

J

13

14

I

4

5

17

L M

Intended use

Your BLACK+DECKER BCMW3318, BCMW3336 lawn

mowers have been designed for mowing grass. These

appliances are intended for consumer use only.

Safety instructions

Warning! When using cordless appli-

ances, basic safety precautions, including

the following, should always be followed

to reduce the risk of re, electric shock,

personal injury and material damage.

Warning! When using the machine the

safety rules must be followed.

For your own safety and bystanders

please read these instructions before

operating the machine. Please keep the

instructions safe for later use.

u Read all of this manual carefully before

operating the appliance.

u The intended use is described in this

manual. The use of any accessory

or attachment or the performance

of any operation with this appliance

other than those recommended in this

instruction manual may present a risk

of personal injury.

u Retain this manual for future refer-

ence.

Using your appliance

Always take care when using the appli-

ance.

u This appliance is not intended for use

by young or inrm persons without

supervision.

u The appliance is not to be used as a

toy.

u Do not allow children or animals to

come near the work area or touch the

appliance or power supply cord.

u Close supervision is necessary when

the appliance is used near children.

u Use in a dry location only. Do not allow

the appliance to become wet. Do not

immerse the appliance in water.

u Do not open body casing. There are

no user serviceable parts inside.

u Do not operate the appliance in

explosive atmospheres, such as in the

presence of ammable liquids, gases

or dust.

5

ENGLISH

(Original instructions)

4

5

u Before using, always visually inspect

to see that the blade, blade bolt and

the blade assembly are not worn or

damaged. Replace worn or damaged

components in sets to preserve bal-

ance. Replace damaged or unreadable

labels.

After use

u When not in use, the appliance should

be stored in a dry, well ventilated place

out of the reach of children.

u Children should not have access to

stored appliances.

u When the appliance is stored or trans-

ported in a vehicle it should be placed

in the boot or restrained to prevent

movement following sudden changes

in speed or direction.

Inspection and repairs

u Before use, check the appliance for

damaged or defective parts. Check for

breakage of parts, damage to switches

and any other conditions that may af-

fect its operation.

u Do not use the appliance if any part is

damaged or defective.

u Have any damaged or defective parts

repaired or replaced by an authorised

repair agent.

u Never attempt to remove or replace

any parts other than those specied in

this manual.

u Be careful during adjustment of the

mower to prevent entrapment of the

ngers between moving blades/parts

and xed parts of the machine.

u To reduce the risk of damage to plugs

and cords never pull the cable to

remove the plug from a socket.

u Before using, always visually inspect

to see that the blades, blade bolts and

cutter assembly are not worn or dam-

aged.

Replace worn or damaged blades and

bolts in sets to preserve balance.

u In order to avoid a hazard due to inad-

vertent resetting of the thermal cut-out,

this appliance must not be supplied

through an external switching device,

such as a timer, or connected to a

circuit that is regularly switched on and

off by the utility.

u Never operate the machine while

people, especially children, or pets are

nearby.

u Keep in mind that the operator or user

is responsible for accidents or hazards

occurring to other people or their prop-

erty.

Before use

u While operating the machine always

wear substantial footwear and long

trousers. Do not operate the ma-

chine when barefoot or wearing open

sandals. Avoid wearing clothing that is

loose tting or that has hanging cords

or ties.

u Thoroughly inspect the area where the

machine is to be used and remove all

objects which can be thrown by the

machine.

6

ENGLISH

(Original instructions)

u When servicing the blades be aware

that, even though the power source

is switched off, the blades can still be

moved.

Additional safety instructions for

lawn mowers

u Do not transport the machine while the

power source is running

u Firmly grip handle with both hands

when operating the lawn mower.

u If at any time it is felt necessary to tilt

the lawn mower, make sure that both

hands remain in the operating position

while the lawn mower is tilted. Keep

both hands in the operating position

until the lawn mower is returned to rest

correctly on the ground.

u Never wear radio or music head-

phones while operating the lawn

mower.

u Never attempt to make a wheel height

adjustment while the motor is running

or while the safety key is in the switch

housing.

u If the lawn mower stalls, release bail

bar to turn mower off, wait for blade to

stop, before attempting to unclog the

chute or remove anything from under

the deck.

u Keep hands and feet away from cut-

ting area.

u Keep blades sharp. Always use protec-

tive gloves when handling the lawn

mower blade.

u If you are using the grass collector,

check it frequently for wear and dete-

rioration.

If excessively worn, replace with a new

grass collector for your safety.

u Use extreme caution when reversing

or pulling the lawn mower towards you.

u Do not put hands or feet near or under

the lawn mower.

Keep clear of the discharger opening

at all times.

u Clear the area where the lawn mower

is to be used of objects such as rocks,

sticks, wire, toys, bones etc., which

could be thrown by the blade.

Objects struck by the blade can cause

severe injury to persons. Stay behind

the handle when the motor is running.

u Do not operate the lawn mower

barefooted or while wearing sandals.

Always wear substantial footwear.

u Do not pull lawn mower backward un-

less absolutely necessary. Always look

down and behind before and while

moving backward.

u Never direct discharged material

toward anyone. Avoid discharging

material against a wall or obstruction.

Material may ricochet back toward the

operator. Release the bail bar to turn

the lawn mower off and stop the blade

when crossing gravel surfaces.

u Do not operate the lawn mower

without the entire grass collector,

discharge guard, rear guard, or other

safety protective devices in place and

working. Periodically check all guards

and safety protective devices to

ensure they are in good working order

and will operate properly and perform

their intended function.

7

ENGLISH

(Original instructions)

Replace a damaged guard or other

safety device before further use.

u Never leave a running lawn mower

unattended.

u Always release the bail bar to stop the

motor and wait until the blade comes

to a complete stop before cleaning the

lawn mower, removing the grass bag,

unclogging the discharge guard, when

leaving the lawn mower, or before

making any adjustments, repairs or

inspections.

u Operate lawn mower only in daylight

or good articial light when objects in

the path of the blade are clearly visible

from the operating area of the lawn

mower.

u Do not operate the lawn mower while

under the inuence of alcohol or drugs,

or when your are tired or ill. Always

stay alert, watch what you are doing,

and use common sense.

u Avoid dangerous environments. Never

operate the lawn mower in damp or

wet grass, never use lawn mower in

the rain. Always be sure of your foot-

ing, walk, never run.

u If the lawn mower should start to

vibrate abnormally, release the bail

bar, wait for the blade to stop and

then check for the cause immediately.

Vibration is generally a warning of

trouble, see the troubleshooting guide

for advise in the case of abnormal

vibration.

u Always wear proper eye and respira-

tory protection when operating the

lawn mower.

u The use of any accessory or attach-

ment not recommended for use with

this lawn mower could be hazardous.

Only use accessories approved by

BLACK+DECKER.

u Never overreach while operating the

lawn mower. Always be sure to keep

proper footing and balance at all times

while operating the lawn mower.

u Mow across the face of slopes,

never up and down. Exercise extreme

caution when changing direction on

slopes.

u Watch for holes, ruts, bumps, rocks or

other hidden objects. Uneven terrain

could cause a slip and fall accident.

Tall grass can hide obstacles.

u Do not mow on wet grass or exces-

sively steep slopes. Poor footing could

cause a slip and fall accident.

u Do not mow near drop-offs, ditches, or

embankments.

You could lose your footing or balance.

u Always allow the mower to cool down

before storing.

Pull the plug from the socket and pull

the battery pack from the machine. Make

sure that all moving parts have come to a

complete stop:

u Whenever you leave the machine;

u Before clearing a blockage;

u Before checking, cleaning or working

on the appliance.

8

ENGLISH

(Original instructions)

Safety of others

u This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

u Children must be supervised to ensure

that they do not play with the appli-

ance.

u After striking a foreign object. Inspect

the appliance for damage and make

repairs as necessary;

Residual risks.

Additional residual risks may arise when

using the tool which may not be included

in the enclosed safety warnings. These

risks can arise from misuse, prolonged

use etc.

Even with the application of the relevant

safety regulations and the implementa-

tion of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotat-

ing/moving parts.

u Injuries caused when changing any

parts, blades or accessories.

u Injuries caused by prolonged use

of a tool. When using any tool for

prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing

dust developed when using your tool

(example:- working with wood, espe-

cially oak, beech and MDF.)

u If operating the mower in a damp

location is unavoidable, use a residual

current device (RCD) with a tripping

current of not more than 30 mA.

Use of an RCD reduces the risk of

electric shock.

u Never pick up or carry an appliance

while the motor is running.

Warning symbols

The following warning symbols are found

on the appliance along with the date

code:

Warning! Read the manual prior

to operation.

Do not expose the appliance to

rain or high humidity.

Beware of sharp blades.

Blades continue to rotate after

the motor is switched off –

Remove disabling device before

maintenance or if cord is dam-

aged.

Beware of ying objects. Keep

bystanders away from the cut-

ting area.

Wear eye protection

The blades will

continue to rotate

after the machine is

switched off.

9

ENGLISH

(Original instructions)

Directive 2000/14/EC guaran-

teed sound power.

Additional safety instructions

for batteries and chargers

Batteries

u Never attempt to open for any reason

.

u Do not expose the battery to water.

u Do not expose the battery to heat.

u Do not store in locations where the

temperature may exceed 40 °C.

u Charge only at ambient temperatures

between 10 °C and 40 °C.

u Charge only using the charger pro-

vided with the appliance/tool. Using

the wrong charger could result in an

electric shock or overheating of the

battery.

u When disposing of batteries, follow

the instructions given in the section

"Protecting the environment".

u Do not damage/deform the battery

pack either by puncture or impact, as

this may create a risk of injury and re.

u Do not charge damaged batteries.

u Under extreme conditions, battery

leakage may occur. When you notice

liquid on the batteries carefully wipe

the liquid off using a cloth. Avoid skin

contact.

u In case of skin or eye contact, follow

the instructions below.

Warning! The battery uid may cause

personal injury or damage to property. In

case of skin contact, immediately rinse

with water.

If redness, pain or irritation occurs seek

medical attention. In case of eye contact,

rinse immediately with clean water and

seek medical attention.

Do not attempt to charge dam-

aged batteries

Charger

Your charger has been designed for a

specic voltage.

Always check that the mains voltage

corresponds to the voltage on the rating

plate.

Warning! Never attempt to replace

the charger unit with a regular mains

plug.

u Use your Black & Decker charger only

to charge the battery in the appliance/

tool with which it was supplied. Other

batteries could burst, causing personal

injury and damage.

u Never attempt to charge non-recharge-

able batteries.

u If the supply cord is damaged, it must

be replaced by the manufacturer or

an authorised Black & Decker Service

Centre in order to avoid a hazard.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

u The appliance/tool/battery must be

placed in a well ventilated area when

charging.

The charger is intended for

indoor use only.

Read the instruction manual

before use.

10

ENGLISH

(Original instructions)

Electrical safety

Your charger is double insulated;

therefore no earth wire is

required.

Always check that the mains voltage

corresponds to the voltage on the rat-

ing plate. Never attempt to replace the

charger

unit with a regular mains plug.

u If the supply cord is damaged, it must

be replaced by the manufacturer or

an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This appliance includes some or all of the following features.

1. Switch box

2. Bail handle

3. Upper-handle

4. Lower-handle

5. Upper-handle attachment knobs (2)

6. Lower-handle attachment port (2)

7. Cut height adjust lever

8. Grass collection bag

9. Rear door cover

10. Carrying handles

Charging procedure

BLACK+DECKER chargers are designed to charge

BLACK+DECKER battery packs.

u Plug the charger into an appropriate outlet before inserting

the battery pack.

u Insert the battery pack into the charger.

The green LED will ash indicating that the

battery is being charged

The completion of charge is indicated by the

green LED remaining on continuously. The pack

is fully charged and may be used at this time or

left on the charger

Warning! Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged

battery.

The red LED ashes in the pattern indicated

on the label. If you see this bad battery blink pattern, do not

continue to charge the battery.

Return it to a service center or a collection site for recycling

Hot/cold pack delay

When the charger detects a battery that

is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery has normalized.

After this happens, the charger automatically switches to the

Pack Charging mode. This feature ensures maximum battery

life. The red LED ashes in the pattern indicated on the label

when the hot / cold pack delay is detected

Important charging notes

u Longest life and best performance can be obtained if the

battery pack is charged when the air temperature is

between 60°F and 80°F (16°- 27°C).

u DO NOT charge the battery pack in an air temperature

below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the

battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 60°F -

80°F (16° - 27°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but not

limited to, steel wool, aluminium foil, or any buildup of me-

tallic particles should be kept away from charger cavities.

11

ENGLISH

(Original instructions)

Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger.

NEVER ATTEMPT TO OPEN THE BATTERY PACK FOR

ANY REASON. IF THE PLASTIC HOUSING OF THE

BATTERY PACK BREAKS OR CRACKS, RETURN TO A

SERVICE CENTER FOR RECYCLING.

Battery state of charge indicator

The battery is equipped with a state of charge indicator.

This can be used to display the current level of charge in the

battery while in the mower and during charging. It does not

indicate tool functionality and is subject to variation based on

product components, temperature and end-user application.

Checking state of charge:

u Press the state of charge indicator button (12a).

u The three LEDs (12b) will illuminate indicating the percent

of charge in the battery. See chart in gure B.

u If LED light does not illuminate, charge battery.

To install battery packs (g. C, C1)

u Lift the battery port cover (14) up to expose the battery

port.

u Slide the battery (12) into the battery port until it is fully

seated and an audible click is heard (gure C).

Make sure battery pack is fully seated and fully latched

into position. The BCMW3318 unit has two battery ports

as shown in Figure C1.

u Close the battery port cover. Ensure the cover is fully

latched before starting mower.

To remove battery packs:

u Open the battery port cover (14) as described above.

u Depress the battery release button on the battery pack

and pull battery pack out of tool.

Assembly

Warning! Before assembly, make sure the bail handle is

released.

Attaching lower handle

u Push the button (4a) on the lower handle attatchment port

(6) and insert the lower handle (4). Adjust the height to

your requirement.

Note! Ensure each side of the lower handle is set at the same

Height.

Attaching upper handle (g. H)

The upper handle has two different mounting position holes to

adjust length of the handle from deck.

The rst set of holes near the bottom of the upper handle tube

allows for maximum handle length. Using the top mounting

position will shorten handle length

u Remove the upper-handle attachment knobs (5) and bolt

(5a) from the upper handle.

u Line up the holes on the bottom of the upper handle (3)

with the holes on the top of the lower handle (4).

u From the outside of the upper handle (3), slide the bolt

through the holes.

u Rotate the upper handle into its operating position.

u Tighten the upper handle attatchment knobs (5).

Securing the motor cable (g. I)

Warning: Attach cable so that it does not become stretched or

pinched in the joints of the handles during use or folding. This

can cause damage to the cord.

The motor cable has to be xed to the handles using the

cable restraints that are already attached to the handle.

To clip the cable to the handle:

u Place the handles in operating position, see “Attaching

lower handle” section.

u Run the cable up the front of the lower and upper handles.

u Pull back the cable restraint.

u Slide the motor cable under the clip and ensure it is fully

held in place by the restraint.

Mulching

Warning! Remove key and Battery packs before removing

Side discharge attachment and Collection bag, and when

Installing mulching insert.

u Ensure the side discharge attachment and the collection

bag are not attached.

u Lift the rear door cover (9) and slide the mulching insert

fully into the mower

u Ensure the rear door cover fully closes before turning

mower on.

Operation

Read this instruction manual before operating your mower.

See “Features” to familiarize yourself with the location of

various controls and adjustments. Save this manual for future

reference.

Warning! Let the mower work at its own pace. Do not

overload.

Warning! Sharp moving blade. Do not operate the mower in

side discharge or mulching mode if the rear door is not

closed under spring tension as serious injury could result.

Take your mower to the nearest service center for repair.

Adjusting mower height

The height of cut is adjusted by the cut height adjust lever.

Note: If you are not sure which height to cut, begin mowing

with the height adjustment lever (7) in the right position.

12

ENGLISH

(Original instructions)

Adjust the height down as needed.

Fitting the grass collection bag (g. F, G)

u Lift the rear door cover (9) as shown in gure (F).

u Place the grass collection bag (8) onto the mower so the

bag hooks (8a) rest on the lugs (8b) as shown in gure

(G). Then lower the rear door.

Starting mower (g. H)

Warning! Sharp moving blade. Never attempt to override the

operation of this switch box as serious injury could result.

Note: Mower is operational when battery or batteries are

installed.

u Your mower is equipped with a special on-off switch box.

To operate the mower, push the button (1a) on the switch

box (1), then pull the bail handle (2) to the handlebar as

shown in gure H. Once the mower starts you can release

the button.

u To turn the mower off, just release the bail handle.

Warning! Never attempt to lock a switch or bail handle (2) in

the on position.

Note: Once the bail handle has returned to the original posi-

tion it will activate the “Automatic Braking Mechanism”. The

motor is electrically braked and the mower blade will stop

rotating in 3 seconds or less.

Mower overload

To prevent damage due to overload conditions, do not try to

remove too much grass at one time. Slow down your cutting

pace, or raise the cut height.

Storage

Warning! Rotating blade can cause serious injury.

Release bail handle (2) to turn mower off, remove battery

before lifting, transporting, or storing the mower. Store in a

dry place.

Warning! To avoid being pinched, keep ngers away from

area between handles when folding down handles.

Warning! Make sure cord does not become stretched or

pinched in the joints of the handles during folding. This can

cause damage to the cord.

The handle of the mower can be easily folded down for quick

and convenient storage.

Carrying the mower

u The mower can be carried using the convenient carry

handles (10). DO NOT attempt to lift the mower by grasp-

ing the upper handle (3) or lower handle (4).

Mowing tips

Warning! Always inspect area where mower is to be used

and remove all stones, sticks, wire, bones, and other debris

which might be thrown by the rotating blade.

Warning! Mow across the face of slopes, never up-and-down.

Exercise extreme caution when changing direction on slopes.

Do not mow excessively steep slopes. Always maintain good

footing.

u Release bail handle to turn mower “Off” when crossing

any gravel area (stones can be thrown by the blade).

u Set mower at highest cutting height when mowing in rough

ground or in tall weeds. Removing too much grass at one

time can cause the motor to be overloaded and to stop.

Refer to troubleshooting guide.

u If a grass collection bag (8) is used during the fast growing

season, the grass may tend to clog up at the discharge

opening. Release bail handle to turn mower off and

remove the safety key. Remove the catcher and shake

the grass down to the back end of the bag. Also clean

out any grass or debris which may be packed around the

discharge opening. Replace the grass catcher.

u If mower should start to vibrate abnormally, release bail

handle to turn mower off and remove safety key. Check

immediately for cause. Vibration is a warning of trouble.

Do not operate mower until a service check has been

made.

Refer to troubleshooting guide in manual.

u Always release bail handle to turn mower off when leaving

it unattended even for a short period of time.

Tips for optimum performance

u Slow down in areas where the grass is especially long or

thick.

u Avoid mowing when the grass is wet from rain or dew-

soaked.

u Cut your lawn frequently, especially during high growth

periods.

Note: It is recommended that your mower be recharged

after use to prolong the battery life.

Frequent charging will not harm your battery, and will ensure

that the battery is fully charged and ready for its next use.

Storing battery not fully charged will shorten battery life.

Removing and installing blade

Warning! When reassembling the blade system, ensure each

part is reinstalled correctly, as described below.

Improper assembly of the blade or other parts of the blade

system may cause serious injury.

Warning! Release bail handle to turn mower off, wait for the

blade to stop, and unplug mower.

u Cut a piece of 2x4 wood (14) (about 610 mm) to keep

blade from turning while removing bolt (13).

u Wear gloves and proper eye protection.

u Turn the mower on its side. Be careful of sharp edges of

blade. Position wood and unscrew bolt with 13mm wrench

13

ENGLISH

(Original instructions)

(36) as shown in gure I.

u Note the orientation of each part as you remove it.

Remove bolt (15) and washer (16). Pull off blade (17) as

shown in Figure J. Examine all pieces for damage and

replace if necessary.

u The blade can only be attached to the fan (20) in one

direction. To reassemble, line up the D-shaped hole of

the blade with the D-shaped post of the fan, ensuring the

writing on the blade faces out away from the mower.

u To tighten, position the piece of wood as shown in Figure

K to keep the blade from turning. Slide the bolt through

the washer and tighten the bolt clockwise into place with a

13mm wrench (13) as shown in Figure K.

Blade sharpening

Keep blade sharp for best mower performance. A dull blade

does not cut grass cleanly. Use proper eye protection while

removing, sharpening, and installing blade. Ensure that safety

key and battery pack is removed.

Sharpening the blade twice during a mowing season is usually

sufcient under normal circumstances.

Sand causes the blade to dull quickly. If your lawn has sandy

soil, more frequent sharpening may be required.

Note: Replace bent or damaged blade immediately.

When sharpening the blade:

u Make sure blade remains balanced.

u Sharpen blade at the original cutting angle.

u Sharpen cutting edges on both ends of blade, removing

equal amounts of material from both ends.

To sharpen blade in a vice (g. L)

u Be sure the bail handle is released, the blade has stopped

and the mower is unplugged before removing the blade.

u Remove blade from mower. See instructions for removing

and installing blade.

u Secure blade (17) in a vice.

u Wear proper eye protection and gloves and be careful not

to cut yourself.

Carefully le the cutting edges of the blade with a ne

tooth le or sharpening stone, maintaining the angle of the

original cutting edge.

Check balance of blade. See instructions for blade balanc-

ing.

u Replace blade on mower and tighten securely.

Blade balancing

Check balance of the blade (17) by placing centre hole in

the blade over a nail or round shank screwdriver, clamped

horizontally in a vice. If either end of the blade rotates down-

ward, le along the sharp edge of that dropping end. Blade is

properly balanced when neither end drops.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require no lubrication.

Cleaning

Release bail handle (2) to turn mower off, let the blade come

to a stop. Use only mild soap and a damp cloth to clean the

mower. Clean out any clippings which may have accumulated

on the underside of the deck. After several uses, check all

exposed fasteners for tightness.

Preventing corrosion

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows: Release

bail handle (2) to turn mower off and unplug mower. Wipe all

exposed parts with a damp cloth.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory opera-

tion depends upon proper tool/appliance care and regular

cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Troubleshooting

If your appliance seems not to operate properly, follow the

instructions below.

If this does not solve the problem, please contact your local

BLACK+DECKER repair agent.

Warning! Before proceeding, release the bail bar to turn

mower off and wait for the blade to stop .

14

ENGLISH

(Original instructions)

Problem Possible solution

Mower doesn’t run when

bail handle is activated.

Check to make sure mower is properly plugged

in and that the button on switch box is being

completely depressed before pulling the bail

handle.

Release bail handle to turn mower off. Remove

battery pack, turn mower over and check that

blade is free to turn.

Check that the battery cavity is free of debris

and is connected properly.

Has battery been fully charged? Press state of

charge button.

Motor stops while mowing. Release bail handle to turn mower off. Remove

battery pack Turn mower over and check that

blade is free to turn.

Raise cutting height of wheels to highest posi-

tion and start mower.

Check that the battery cavity is free of debris

and is connected properly

Has battery been fully charged? Press state of

charge button

Avoid overloading the mower. Slow down the

cutting pace, or raise the cut height.

Mower runs but cutting

performance is unsatisfac-

tory,

Release bail handle to turn mower off. Unplug

mower. Turn mower over and check:

u Blade for sharpness - Keep blade sharp.

u Deck and discharge chute for clogging.

Wheel height adjustment may be set too low for

grass condition. Raise cutting height.

Mower is too hard to push. Release bail handle to turn mower off. Unplug

mower. Raise cutting height to reduce deck

drag on grass. Check each wheel for free

rotation

Mower is abnormally noisy

and vibrates.

Release bail handle to turn mower off. remove

battery pack. Turn mower on side and check

blade to ensure it has not been bent or

damaged. If blade is damaged, replace with

a BLACK+DECKER replacement blade. If

the underside of the deck is damaged, return

mower to a BLACK+DECKER Authorized

service center.

If there is no visible damage to the blade and

the mower still vibrates:

u Release bail handle to turn mower off.

u Remove battery pack.

u Disassemble entire blade assembly as

described in the “Removing and installing

blade” section.

u Remove any debris and clean each piece.

u Replace each piece as described in the

“Removing and installing blade” section.

If mower still vibrates, return the mower to

an authorized BLACK+DECKER authorized

service center.

Battery charger LEDs

not on.

Check plug connection.

Replace charger.

Mower not picking up

clippings with bag.

Chute clogged. Release bail handle to turn

mower off. Remove battery pack. Clear chute of

grass clippings.

Raise cutting height of wheels to shorten length

of the cut.

Bag full. Empty bag more often.

Protecting the environment

Z

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be

recovered or recycled, reducing demand for raw materials.

Please recycle electrical products and batteries according to

local provisions. Further information is available at

www.2helpU.com

Technical data

BCMW3318 BCMW3336

Voltage

Vdc 18V 36V

No-Load Speed

min

-1

3800RPM 3800RPM

Weight

kg

15 15

Blade length

cm 33 33

Batteries Chargers (minutes)

Cat# Vdc Ah Weight Kg

Cat# 90590287* N517388* BDC1A BDC2A BDC2A36

Amps 400mA 1A 1A 2A 1.35A

BL1518 18 1.5 0.38 BL1518 225 90 90 45 X

BL1518ST 18 1.5 0.38 BL1518ST 225 90 90 45 X

BL2018 18 2.0 0.39 BL2018 300 120 120 60 X

BL2018ST 18 2.0 0.39 BL2018ST 300 120 120 60 X

BL2518 18 2.5 0.43 BL2518 380 150 150 75 X

BL4018 18 4.0 0.64 BL4018 600 240 240 120 X

BL5018 18 5.0 0.7 BL5018 750 300 300 135 X

BL20362 36 2.0 0.64 BL20362 X X X X 90

BL2536 36 2.5 0.68 BL2536 X X X X 110

BL1554 18/54 1.5 1.08 BL1554 225 90 90 45 X

BL2554 18/54 2.5 1.2 BL2554 380 150 150 75 X

Hand/arm weighted vibration value:

= <2.5 m/s

2

, uncertainty (K) = 1.5m/s

2

.

L

PA

(sound preasure) 74.5 dB(A)

uncertainty (K) = 2.5 dB(A)

L

WA

(sound power) 86 dB(A)

uncertainty (K) = 1.5 dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

%

BCMW3318, BCMW3336 lawn mower

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1:2012 + A11:2014,

EN 60335-2-77:2010

15

(Übersetzung der ursprünglichen

Anweisungen)

DEUTSCH

ENGLISH

(Original instructions)

Verwendungszweck

Ihr BLACK+DECKER Rasenmäher BCMW3318, BCMW3336

wurde zum Mähen von Rasen entwickelt. Diese Geräte sind

nicht für den gewerblichen Einsatz vorgesehen.

Sicherheitshinweise

Warnung! Beachten Sie beim Umgang

mit kabellosen Geräten stets die

grundlegenden Sicherheitshinweise,

die im Folgenden beschrieben werden.

Dadurch verhindern Sie Brände,

Stromschläge sowie Sach- und

Personenschäden.

Warnung! Beachten Sie beim

Verwenden des Geräts unbedingt die

Sicherheitsregeln.

Lesen Sie zu Ihrer eigenen Sicherheit

und zum Schutz in der Nähe bendlicher

Personen vor Gebrauch des Geräts

die folgende Bedienungsanleitung.

Heben Sie diese Anleitung zur späteren

Verwendung gut auf.

u Lesen Sie diese Anleitung vollständig

und aufmerksam durch, bevor Sie das

Gerät verwenden.

u Der vorgesehene Verwendungszweck

ist in dieser Anleitung beschrieben.

Bei Verwendung von Zubehör oder

Anbauteilen, die nicht in dieser

Anleitung empfohlen werden, sowie

bei der Verwendung des Geräts

in Abweichung von den in dieser

Anleitung beschriebenen Verfahren

besteht Verletzungsgefahr.

u Bewahren Sie diese Anleitung auf.

Verwendung des Geräts

Verwenden Sie das Gerät stets mit

Umsicht.

2000/14/EC, Lawn Mower, L < 50cm, Annex VI,

DEKRA Certication B.V. Meander 1051 / P.O. Box 5185

6825 MJ ARNHEM / 6802 ED ARNHEM, Netherlands

Notied Body ID No.: 0344

Level of accoustic power according to 2000/14/EC (Article 12,

Annex III, L< 50cm):

L

WA

(measured sound power) 86 dB(A)

uncertainty (K) = 1.5 dB(A)

L

WA

(guaranteed sound power) 96 dB(A)

These products also comply with directive 2014/30/EU,

2011/65/EU. For more information, please contact Black &

Decker at the following address or refer to the back of the

manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

Becky Cotsworth

Director – Outdoor Products Group

Black & Decker Europe, 270 Bath Road, Slough,

Berkshire, SL1 4DX

United Kingdom

11/10/2019

Guarantee

Black & Decker is condent of the quality of its products and

offers consumers a 24 month guarantee from the date of

purchase. This guarantee75 is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance

with Black&Decker Terms and Conditions and you will need to

submit proof of purchase to the seller or an authorised repair

agent. Terms and conditions of the Black&Decker 2 year

guarantee and the location of your nearest authorised repair

agent can be obtained on the Internet at www.2helpU.com, or

by contacting your local Black & Decker ofce at the address

indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and receive updates on new

products and special offers.

16

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

u Das Gerät ist nicht für die

unbeaufsichtigte Verwendung durch

Kinder oder gebrechliche Personen

vorgesehen.

u Das Gerät ist kein Spielzeug.

u Achten Sie darauf, dass sich im

Arbeitsbereich keine Kinder oder

Tiere aufhalten. Verhindern Sie, dass

Kinder das Gerät oder das Netzkabel

berühren.

u Seien Sie besonders vorsichtig, wenn

Sie das Gerät

in der Nähe von Kindern

verwenden.

u Verwenden Sie das Gerät nur in

trockener Umgebung. Achten Sie

darauf, dass das Gerät nicht nass

wird. Tauchen Sie das Gerät nicht in

Wasser.

u Versuchen Sie nicht, das Gehäuse

zu öffnen.

Es gibt keine vom Benutzer

zu wartenden Teile im Inneren des

Geräts.

u Betreiben Sie das Gerät nicht in

explosionsgefährdeter Umgebung,

in der sich brennbare Flüssigkeiten,

Gase oder Staub benden.

u Ziehen Sie niemals am Kabel, wenn

Sie den Stecker aus der Steckdose

ziehen möchten. Kabel und Stecker

könnten sonst beschädigt werden.

u Überzeugen Sie sich vor der

Verwendung, dass Mähmesser,

Messerschrauben und Mäheinheit

weder abgenutzt noch beschädigt

sind.

Ersetzen Sie bei abgenutzten oder

beschädigten Messern und Schrauben

den entsprechenden Satz, sodass

nicht neue und alte Komponenten

gleichzeitig verwendet werden.

u Um eine Gefährdung durch

unbeabsichtigtes Wiedereinschalten

des Thermoschutzes zu vermeiden,

darf dieses Gerät nicht über eine

externe Schalteinrichtung wie z. B.

einen Zeitgeber versorgt werden oder

an einen Schaltkreis angeschlossen

werden, der durch den Versorger

regelmäßig ein- und ausgeschaltet

wird.

u Es sollte stets ein Sicherheitsabstand

zu anderen Personen, insbesondere

Kindern, und Haustieren eingehalten

werden.

u Beachten Sie, dass der Bediener bzw.

Benutzer für eventuelle Personen-

oder Sachschäden verantwortlich ist.

Vor dem Gebrauch

u Tragen Sie stets feste Schuhe und

eine lange Hose, wenn Sie mit

dem Gerät arbeiten. Betreiben Sie

dieses Gerät nie barfuß oder in

offenen Sandalen. Tragen Sie keine

lose Kleidung oder Kleidung mit

herabhängenden Bändern.

u Kontrollieren Sie stets den Bereich, in

dem das Gerät verwendet werden soll,

und entfernen Sie alle Gegenstände,

die von dem Gerät umhergeschleudert

werden können.

17

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

u Überzeugen Sie sich vor der

Verwendung, dass Mähmesser,

Messerschraube und Mäheinheit

weder abgenutzt noch beschädigt

sind. Ersetzen Sie bei abgenutzten

oder beschädigten Bestandteilen

den entsprechenden Satz, sodass

nicht neue und alte Komponenten

gleichzeitig verwendet werden.

Ersetzen Sie beschädigte oder

unlesbare Aufkleber.

Nach dem Gebrauch

u Bewahren Sie das Gerät bei

Nichtgebrauch an einem trockenen,

gut belüfteten Ort außerhalb der

Reichweite von Kindern auf.

u Kinder sollten keinen Zugang zu

aufbewahrten Geräten haben.

u Wenn das Gerät in einem Fahrzeug

transportiert oder gelagert wird,

bewahren Sie es im Kofferraum oder

einer geeigneten Ablage auf, damit

es bei plötzlichen Geschwindigkeits-

oder Richtungsänderungen nicht in

Bewegung geraten kann.

Inspektion und Reparaturen

u Prüfen Sie das Gerät vor der

Verwendung auf beschädigte oder

defekte Teile. Prüfen Sie, ob Teile

gebrochen sind, Schalter beschädigt

sind oder andere Bedingungen

vorliegen, welche die Funktion

beeinträchtigen könnten.

u Betreiben Sie das Gerät nicht, wenn

ein Teil beschädigt oder defekt ist.

u Lassen Sie beschädigte oder defekte

Teile in einer Vertragswerkstatt

reparieren oder austauschen.

u Ersetzen oder entfernen Sie keine

Teile, für die in dieser Anleitung

keine entsprechende Beschreibung

enthalten ist.

u Gehen Sie bei Einstellungen am

Rasenmäher vorsichtig vor, um zu

verhindern, dass Ihre Finger zwischen

den beweglichen Messern/Teilen

und feststehenden Teilen des Geräts

eingeklemmt werden.

u Beachten Sie bei Wartungsarbeiten

an den Messern, dass sich diese auch

ohne Stromversorgung

bewegen.

Zusätzliche Sicherheitshinweise

für Rasenmäher

u Transportieren Sie die Maschine nicht,

während die Stromversorgung läuft.

u Halten Sie den Rasenmäher während

des Betriebs sicher mit beiden Händen

fest.

u Halten Sie beide Hände in der

Betriebsposition, wenn der

Rasenmäher gekippt werden muss.

Halten Sie beide Hände in der

Betriebsposition bis der Rasenmäher

wieder ordnungsgemäß auf dem

Boden abgestellt wurde.

u Tragen Sie beim Rasenmähen keine

Kopfhörer zum Musikhören.

u Passen Sie niemals die Höhe der

Räder an, während der Motor läuft

oder sich der Sicherheitsschlüssel im

Schloss bendet.

18

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

u Lassen Sie den Bügelgriff los, um den

Rasenmäher auszuschalten, wenn

dieser blockiert. Warten Sie, bis das

Messer zum Stillstand gekommen ist,

bevor Sie versuchen, die Verstopfung

zu beseitigen oder Gegenstände von

der Unterseite zu entfernen.

u Halten Sie Hände und Füße vom

Schnittbereich fern.

u Halten Sie die Sägeblätter scharf.

Tragen Sie beim Umgang mit dem

Messer des Rasenmähers stets

Schutzhandschuhe.

u Wenn der Grasfangbehälter verwendet

wird, muss dieser regelmäßig auf

Abnutzungen und Beschädigungen

überprüft werden.

Wechseln Sie aus Sicherheitsgründen

den Grasfangbehälter bei starker

Abnutzung aus.

u Seien Sie besonders vorsichtig, wenn

Sie den Rasenmäher wenden oder in

Ihre Richtung ziehen.

u Bringen Sie Hände oder Füße nicht in

die Nähe bzw. unter den Rasenmäher.

Halten Sie jederzeit einen

Sicherheitsabstand zur

Auswurföffnung.

u Entfernen Sie Steine, Äste, Drähte,

Spielzeuge, Knochen usw., die in das

Messer geraten könnten, aus dem

Bereich, in dem der Rasenmäher

verwendet wird.

Objekte, die in das Messer geraten,

können ernsthafte Verletzungen

verursachen. Bleiben Sie hinter dem

Griff, wenn der Motor läuft.

u Betreiben Sie den Rasenmäher weder

barfuß noch mit Sandalen. Tragen Sie

jederzeit festes Schuhwerk.

u Ziehen Sie den nur Rasenmäher

nur rückwärts, wenn dies unbedingt

erforderlich ist. Achten Sie stets auf

den Boden und den Bereich hinter

Ihnen, bevor und während Sie sich

rückwärts bewegen.

u Achten Sie darauf, dass das Material

nicht in Richtung von Personen

ausgeworfen wird. Achten Sie

darauf, dass das Material nicht in

Richtung von Wänden oder anderen

Gegenständen ausgeworfen wird.

Das Material kann gegen den

Bediener zurückgeschleudert werden.

Lassen Sie den Bügelgriff los, und

warten Sie, bis das Messer zum

Stillstand gekommen ist, bevor Sie

Kiesoberächen überqueren.

u Betreiben Sie den Rasenmäher nicht

ohne angebrachten und intakten

Grasfangbehälter, Auswurfschutz,

hinteren Schutz und andere

Schutzvorrichtungen. Überprüfen

Sie regelmäßig alle Schutz- und

Sicherheitsvorrichtungen auf deren

ordnungsgemäße Funktion.

Ersetzen Sie beschädigte Schutz-

und Sicherheitsvorrichtungen vor der

weiteren Verwendung.

u Lassen Sie den eingeschalteten

Rasenmäher niemals unbeaufsichtigt.

19

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

u Lassen Sie stets den Bügelgriff

los, warten Sie, bis das Messer

zum Stillstand gekommen ist,

wenn Sie den Rasenmäher

reinigen, den Grasfangbeutel

entfernen, Verstopfungen aus der

Auswurföffnung beseitigen, den

Rasenmäher unbeaufsichtigt lassen

bzw. Anpassungen vornehmen

oder Reparaturen und Inspektionen

ausführen.

u Betreiben Sie den Rasenmäher nur

bei Tageslicht oder bei ausreichender

Beleuchtung, sodass Gegenstände auf

dem Schnittweg vom

Betriebsbereich

des Rasenmähers aus deutlich

sichtbar sind.

u Betätigen Sie den Rasenmäher

nicht, wenn Sie unter Alkohol- oder

Drogeneinuss stehen oder wenn

Sie müde oder krank sind. Bleiben

Sie immer aufmerksam, achten Sie

darauf, was sie tun und setzen Sie den

gesunden Menschenverstand ein.

u Meiden Sie gefährliche Umgebungen.

Betreiben Sie den Rasenmäher nicht

in feuchtem oder nassem Gras.

Verwenden Sie den Rasenmäher

keinesfalls im Regen. Achten Sie auf

Trittsicherheit. Betreiben Sie das Gerät

nur im Gehen, nie rennend.

u Lassen Sie den Bügelgriff los,

warten Sie, bis das Messer zum

Stillstand gekommen ist, wenn Sie

ungewöhnliche Vibrationen des

Rasenmähers bemerken, und prüfen

Sie die Ursache.

Im Allgemeinen deutet Vibration

auf ein Problem hin. Im Fall einer

ungewöhnlichen Vibration des Geräts

nden Sie unter „Problembehebung“

weitere Informationen.

u Tragen Sie beim Betreiben des

Rasenmähers stets geeigneten Augen-

und Atemschutz.

u Der Gebrauch von Zubehörteilen

oder Zusätzen, die nicht für den

Gebrauch mit dem Rasenmäher

BLACK+DECKER BCMW3336 Manuale utente

Questo manuale è adatto anche per

BLACK+DECKER BCMW3336 Manuale utente

in altre lingue

Documenti correlati

Altri documenti