DTS X-BRICK Outdoor RGBW Fluter, IP65 Manuale utente

X-BRICK

USER’S MANUAL rel. 1.0 GB

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS ................................................................................................................. 4

2- GENERAL WARNING .............................................................................................. 5

3- GENERAL WARRANTY CONDITIONS .................................................................... 5

4- TECHNICAL FEATURES ......................................................................................... 5

5- ACCESSORIES ........................................................................................................ 7

6- IMPORTANT SAFETY INFORMATION .................................................................... 8

6.1 Fire prevention...................................................................................................... 8

6.2 Prevention of electric shock .................................................................................. 8

6.3 Safety ................................................................................................................... 8

6.4 Level of protection against the penetration of solid and liquid objects .................. 8

6.5 Waste Electrical and Electronic Equipment (WEEE) directive .............................. 9

7- INSTALLATION ........................................................................................................ 9

7.1 Floor mounting installation .................................................................................... 9

7.2 Ceiling mounting installation ............................................................................... 10

7.3 Display UV protection ......................................................................................... 11

7.4 Protection against liquids .................................................................................... 12

7.5 Movement ........................................................................................................... 12

7.6 Risk of fire .......................................................................................................... 12

7.7 Forced ventilation ............................................................................................... 13

7.8 Ambient temperature .......................................................................................... 13

8- INPUT / OUTPUT CONNECTIONS ......................................................................... 13

9- DMX SIGNAL CONNECTION ................................................................................. 14

9.1 DMX Addresses .................................................................................................. 15

9.2 Selecting the DMX address ................................................................................ 15

10- RDM FUNCTIONS ................................................................................................ 15

11- FIRMWARE UPDATING ....................................................................................... 21

12- DISPLAY FUNCTIONS ......................................................................................... 22

13- REC MODE ........................................................................................................... 29

14- ERROR MESSAGES ............................................................................................ 30

15- PERIODIC CLEANING ......................................................................................... 31

16- PERIODIC CONTROLS ........................................................................................ 31

17- HOLOGRAPHIC FILTER INSTALLATION ........................................................... 32

18- LENSES SET REPLACEMENT ............................................................................ 33

19- BARNDOOR INSTALLATION .............................................................................. 34

20- LED PIXEL INVERT FUNCTION REFERENCES ................................................. 35

21- DMX PROTOCOL ................................................................................................. 36

4

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC

SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL INDICATES THE MAXIMUM

OPERATING AMBIENT TEMPERATURE

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE FROM THE ILLUMINATED OBJECTS

THIS SYMBOL MEANS “DO NOT STARE

AT THE OPERATING LIGHT SOURCE”

THIS SYMBOL INDICATES

PHOTOBIOLOGICAL SAFETY

THIS SYMBOL INDICATES THE EUROPEAN

COMMUNITY DIRECTIVE 2012/19/EC ON

WASTE ELECTRICAL AND ELECTRONIC

EQUIPMENT (WEEE)

!

5

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The unit is not for household use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

The warranty covers defects in materials and workmanship. The warranty is not

appliable where a defect is caused by misuse or unauthorised repair of the product.

Any functional or/and physical modification of the product is not allowed.

4- TECHNICAL FEATURES

DTS product codes:

03.LDB130S11FC X-BRICK FC Ultra-Narrow lenses Black finishing

Output

32 OSTAR STAGE “N” Full Color (RGBW) LEDs

15.300 lumens output

LED lifespan: 50.000 hours (70% lumen output)

Optical group

8° projection angle

Range of quick-mounting holographic filters included: 20° / 40° / 60°x10° (no mounting

tools required)

Uniform projection on surfaces

Color generation

16 million colors

Wide palette of pure uniform Whites with variable linear color temperature (2700K –

8000K)

16 gel filter emulations

Control

Wireless DMX transmitter/receiver (built-in)

DMX 512 / RDM protocols

LCD display + 4 capacitive touch keys

Internal operating system updatable via DTS Dongle Firmware Uploader

9 DMX modes:

DMX Full Operation modes

- Chase (default)

- Extended

- Sectors RGBW X4

- Sectors RGBW Fine X4

- Sectors RGBW + Shut + Dim X4

6

DMX Single Layer modes (compatibility with all BRICK models)

- Standard

- Global RGBW

- Global RGBW + Shut + Dim

- Global RGBW + Dim Fine

Power supply

Built-in full-range PSU 100-240Vac 50-60 Hz

Power consumption: 650W

Connections

PowerCON TRUE1 In/Out IP65 panel connectors with water-proof caps

XLR 5 pins In/Out IP65 panel connectors with water-proof caps

Internal safety devices

Overvoltage and overtemperature circuits protection

Operating ambient temperature

-20° / 40°

Physical

IP65

IK protection degree: IK09

Weight: 14 Kg

Finishing: Black

Certifications

DIMENSIONS

7

5- ACCESSORIES

As standard

1 x Holographic filter 20° (code 0506A043.D18)

1 x Holographic filter 40° (code 0506A045.D18)

1 x Holographic filter 60°x10° (code 0506A092.D18)

1 x Cable with PowerCON TRUE1 female connector (code 02K0012267.0015)

1 x XLR 5-pole IP65 female cable connector (code 0508B177)

1 x XLR 5-pole IP65 male cable connector (code 0508B178)

1 x Display UV protection (code 03.LA.218)

1 x Omega bracket with “Fast Lock” (code 02K00467)

1 x User’s Manual

Optional (on request)

- Holographic filter 10° (code 0506A101.D18)

- Holographic filter 60° (code 0506A103.D18)

- Holographic filter 80° (code 0506A121.D18)

- Holographic filter 30x60° (code 0506A133.D18)

- Barndoor black finishing (code 03.LA.237.11)

- Visor black finishing (code 03.LA.236.11)

- Aliscaf clamp for tube diameter 50 mm (Max load 200 Kg) (code 0521A033)

(indicated for any kind of loads vertical / horizontal)

- Professional Quick trigger clamp (Max load 100 Kg) (code 0521A037) (not indicated

for horizontal load)

- “C” Clamp G60 (Max load 50 Kg) (code 0521A004) (not indicated for horizontal load)

- Safety cable 5 x 600 mm (Max load 60 Kg) (code 0521A038)

- DTS Dongle firmware uploader (code 03.LA.206)

8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

-Minimum distance from the closest illuminable surface: 0,5 m.

- Replace any blown or damaged fuses only with those of identical value.

Attention: the fuse replacement must be made by DTS personnel or experienced

person.

-Connect the unit to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any

function which involves touching the inside of the projector.

-The level of technology inherent in the X-BRICK requires the assistance of

specialised personnel for all servicing.

Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the unit.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Safety:

-Risk Group 2 product according to EN 62471.

CAUTION. Do not look directly into the light output. May be harmful to the eyes and

skin.

-Do not stare at the operating light source.

- The luminaire should be positioned so that prolonged staring into the luminaire at a

distance of 25,94 m is not expected.

-The light source contained in this luminaire shall only be replaced by the

manufacturer or his service agent or a similar qualified person.

-The unit is not for household use and must be installed by a qualified electrician or

experienced person.

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the

failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 60°C. Never handle

the unit until at least 5 minutes have elapsed since the projector was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

6.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an outdoor appliance and its protection level against the

penetration of solid and liquid objects is IP65.

Suitable for wet locations.

!

9

6.5 Waste Electrical and Electronic equipment (WEEE) directive:

-The machine, accessories and packaging should be sorted for environmetal-friendly

Recycling.

For EC countries: according to the European Directive 2012/19/EC for Waste

Electrical and Electronic Equipment and its implementation into national right,

luminaires that are no longer usable must be collected separately and disposed of in

an environmentally correct manner.

7- INSTALLATION

The unit is suitable for wet locations.

7.1 Floor mounting installation

BRICK may be either floor or ceiling mounted.

For floor mounting installation, X-BRICK is supplied with four rubber mounting feet on

its bracket to be used as a self standing projector.

10

7.2 Ceiling mounting installation

For ceiling mounting installation, it is recommended the use of appropriate clamps to

fix the unit to the mounting surface.

An included Omega bracket with Fast Lock connections allows to hang X-BRICK by

using fixing clamps for truss.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hung it.

For outdoor application where X-BRICK needs to be installed vertically keep the

unit display towards the floor.

ATTENTION:

A safety cable must be securely fixed to the unit’s mounting bracket and to the support

structure of the projector as shown in the picture.

A suitable safety cable (code 0521A038) is available on demand.

Installation with Omega bracket:

11

Installation without Omega bracket:

7.3 Display UV Protection

For outdoor installation, X-BRICK is provided with a Display UV protection (code

03.LA.218).

To install the Display UV protection:

Put in place the UV protection plate and the gasket on the display panel and fix both

with the 2 marked screws provided in the kit.

Fix the safety cable on the side cap with the marked screw and the washer provided in

the kit as shown in the picture.

12

7.4 Protection against liquids

If IP65 protection is impaired for any reason, do not expose this product to external

atmospheric agents, because it could be damaged.

7.5 Movement

The projector has a maximum movement of 105° for Tilt.

7.6- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

Minimum distance from the object being illuminated is 0,5 m.

7.7- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans.

These should, under no circumstances, be blocked or obstructed whilst the projector is

in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

7.8- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should not exceed 40°C.

13

8- INPUT / OUTPUT CONNECTIONS

WIRELESS DMX

Built-in Lumen Radio

Wireless DMX

transmitter/receiver

Ergonomic double handles

MAINS IN

100-240Vac 50-60 Hz

PowerCON TRUE1 male

IP65 panel connector

with water-proof cap

MAINS OUT

100-240Vac 50-60 Hz (MAX 16A)

PowerCON TRUE1 female

IP65 panel connector

with water-proof cap

Max 4 X-BRICK units @ 230Vac

Max 2 X-BRICK units @ 100Vac

DMX OUT

XLR 5-pole female

IP65 panel connector

with water-proof cap

DMX IN

XLR 5-pole male

IP65 panel connector

with water-proof cap

14

9- DMX SIGNAL CONNECTION:

The unit operates using a digital DMX 512 signal.

Connection between the controller and the unit or between units must be carried out

using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the DMX connector chassis.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

unit to the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

If the display showing the DMX address flashes, then one of the following errors has

occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we

suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

15

9.1 DMX addresses

X-BRICK can be used in 9 DMX modes:

1. Standard (10 ch)

2. Chase (23 ch) (Default)

3. Extended (29 ch)

4. Global RGBW (4 ch)

5. Global RGBW + Shut + Dim (6 ch)

6. Global RGBW + Dim Fine (10 ch)

7. Sectors RGBW X4 (16 ch)

8. Sectors RGBW Fine X4 (32 ch)

9. Sectors RGBW + Shut + Dim X4 (24 ch)

DMX Full Operation modes

- Chase (default)

- Extended

- Sectors RGBW X4

- Sectors RGBW Fine X4

- Sectors RGBW + Shut + Dim X4

DMX Single Layer modes (compatibility with all BRICK models)

- Standard

- Global RGBW

- Global RGBW + Shut + Dim

- Global RGBW + Dim Fine

In order to use the unit in “Chase” mode (23 DMX channels) (Default), set the following

addresses on the mixer:

Projector 1 A001

Projector 2 A024 If you want to select the next projector, just add “23”

Projector 3 A047

….. A….

projector 6 A116

9.2 Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more

quickly and you get a faster selection.

16

10- RDM FUNCTIONS

By using a RDM controller it is possible to set DMX address, DMX mode and other

parameters. X-BRICK accepts the following RDM commands:

RDM Device Model ID: 0x0D65

RDM PID DESCRIPTION

RDM PID VALUE

GET

SET

Category – Network Management

DISC_UNIQUE_BRANCH

0x0001

DISC_MUTE

0x0002

DISC_UN_MUTE

0x0003

Category – Status Collection

STATUS_MESSAGES

0x0030

X

STATUS_ID_DESCRIPTION

0x0031

X

Category - RDM Information

SUPPORTED_PARAMETERS

0x0050

X

PARAMETERS_DESCRIPTION

0x0051

X

Category – Product Information

DEVICE_INFO

0x0060

X

DEVICE_MODEL_DESCRIPTION

0x0080

X

MANUFACTURER_LABEL

0x0081

X

DEVICE_LABEL

0x0082

X

SOFTWARE_VERSION_LABEL

0x00C0

X

Category - DMX512 Setup

DMX_PERSONALITY

0x00E0

X

DMX_PERSONALITY_DESCRIPTION

0x00E1

X

DMX_START_ADDRESS

0x00F0

X

Category – Sensors

SENSOR_DEFINITION

0x0200

X

SENSOR_VALUE

0x0201

X

Category – Power/Lamp Settings

DEVICE_HOURS

0x0400

X

LAMP_HOURS

0x0401

X

Category – Display Settings

DISPLAY_INVERT

0x0500

X

Category – Control

IDENTIFY_DEVICE

0x1000

X

Category – Dimmer Settings (Additional Messages)

CURVE

0x0343

X

CURVE_DESCRIPTION

0x0344

X

OUTPUT_RESPONSE_TIME

0x0345

X

OUTPUT_RESPONSE_TIME_DESCRIPTION

0x0346

X

MODULATION_FREQUENCY

0x0347

X

MODULATION_FREQUENCY_DESCRIPTION

0x0348

X

17

10- RDM FUNCTIONS

RDM PID DESCRIPTION

RDM PID VALUE

GET

SET

Category – Manufacturer-Specific PIDs

LED PIXEL INVERT

0x9039

X

FANS SETTING

0x903A

X

DISPLAY STANDBY

0x903C

X

BKGND-CHS CROSSFADE

0x903D

X

NO DMX ACTION

0x9002

X

RED NO DMX

0x9003

X

GREEN NO DMX

0x9004

X

BLUE NO DMX

0x9005

X

WHITE NO DMX

0x9006

X

INT NO DMX

0x900A

X

RED FINE NO DMX

0x9014

X

GREEN FINE NO DMX

0x9015

X

BLUE FINE NO DMX

0x9016

X

WHITE FINE NO DMX

0x9017

X

INT FINE NO DMX

0x9018

X

RED2 NO DMX

0x9019

X

GREEN2 NO DMX

0x901A

X

BLUE2 NO DMX

0x901B

X

WHITE2 NO DMX

0x901C

X

INT2 NO DMX

0x901D

X

RED2 FINE NO DMX

0x901E

X

GREEN2 FINE NO DMX

0x901F

X

BLUE2 FINE NO DMX

0x9020

X

WHITE2 FINE NO DMX

0x9021

X

INT2 FINE NO DMX

0x9022

X

RED3 NO DMX

0x9023

X

GREEN3 NO DMX

0x9024

X

BLUE3 NO DMX

0x9025

X

WHITE3 NO DMX

0x9026

X

INT3 NO DMX

0x9027

X

RED3 FINE NO DMX

0x9028

X

GREEN3 FINE NO DMX

0x9029

X

BLUE3 FINE NO DMX

0x902A

X

WHITE3 FINE NO DMX

0x902B

X

INT3 FINE NO DMX

0x902C

X

RED4 NO DMX

0x902D

X

GREEN4 NO DMX

0x902E

X

BLUE4 NO DMX

0x902F

X

WHITE4 NO DMX

0x9030

X

INT4 NO DMX

0x9031

X

RED4 FINE NO DMX

0x9032

X

GREEN4 FINE NO DMX

0x9033

X

BLUE4 FINE NO DMX

0x9034

X

WHITE4 FINE NO DMX

0x9035

X

INT4 FINE NO DMX

0x9036

X

18

10- RDM FUNCTIONS

RDM ADDITIONAL MESSAGEs:

CURVE

CURVE DESCRIPTION

1

1: LINEAR

2

2: QUADRATIC (default)

3

3: S-CURVE

4

4: GAMMA 2.2

OUTPUT RESPONSE TIME

OUTPUT_RESPONSE_TIME_DESCRIPTION

0

0: SMOOTH OFF

1

1: SMOOTH 1 ( 25 ms)

2

2: SMOOTH 2 ( 50 ms)

3

3: SMOOTH 3 ( 75 ms)

4

4: SMOOTH 4 (100 ms) (default)

5

5: SMOOTH 5 (125 ms)

6

6: SMOOTH 6 (150 ms)

7

7: SMOOTH 7 (175 ms)

8

8: SMOOTH 8 (200 ms)

9

9: SMOOTH 9 (225 ms)

10

10: SMOOTH 10 (250 ms)

11

11: SMOOTH 11 (275 ms)

12

12: SMOOTH 12 (300 ms)

13

13: SMOOTH 13 (325 ms)

14

14: SMOOTH 14 (350 ms)

15

15: SMOOTH 15 (375 ms)

16

16: SMOOTH 16 (400 ms)

17

17: SMOOTH 17 (425 ms)

18

18: SMOOTH 18 (450 ms)

19

19: SMOOTH 19 (475 ms)

20

20: SMOOTH 20 (500 ms)

19

10- RDM FUNCTIONS

RDM ADDITIONAL MESSAGEs:

MODULATION FREQUENCY

MODULATION FREQUENCY DESCRIPTION

1

1: 610 Hz

2

2: 800 Hz

3

3: 1000 Hz (default)

4

4: 1500 Hz

5

5: 2000 Hz

6

6: 2500 Hz

7

7: 3000 Hz

8

8: 3500 Hz

9

9: 4000 Hz

10

10: 4500 Hz

11

11: 5000 Hz

RDM MANUFACTURER-SPECIFIC PIDs:

MANUFACTURER-SPECIFIC PID

DESCRIPTION

LED PIXEL INVERT

0 = Disabled (default)

1 = Enabled

FANS SETTING

0 = Fan mode Standard (default)

1 = Fan mode Silent

2 = Fan mode Ultra-Silent

3 = Fan mode Auto

DISPLAY STANDBY

0 = DISABLED (Default)

1 = ENABLED

2 = FORCED ENABLED

NO DMX ACTION

1 = BLACKOUT

2 = PROGRAM 1-16

3 = RGB 100%

4 = RGB 60%

5 = CUSTOM

6 = CUSTOM2

7 = CUSTOM3

8 = CUSTOM4

9 = KEEP LAST (default)

20

RDM MANUFACTURER-SPECIFIC PIDs:

MANUFACTURER-SPECIFIC PID

DESCRIPTION

RED NO DMX

Range 0-255 (Default = 128)

GREEN NO DMX

Range 0-255 (Default = 128)

BLUE NO DMX

Range 0-255 (Default = 128)

WHITE NO DMX

Range 0-255 (Default = 128)

INT NO DMX

Range 0-255 (Default = 128)

RED FINE NO DMX

Range 0-255 (Default = 128)

GREEN FINE NO DMX

Range 0-255 (Default = 128)

BLUE FINE NO DMX

Range 0-255 (Default = 128)

WHITE FINE NO DMX

Range 0-255 (Default = 128)

INT FINE NO DMX

Range 0-255 (Default = 128)

RED2 NO DMX

Range 0-255 (Default = 128)

GREEN2 NO DMX

Range 0-255 (Default = 128)

BLUE2 NO DMX

Range 0-255 (Default = 128)

WHITE2 NO DMX

Range 0-255 (Default = 128)

INT2 NO DMX

Range 0-255 (Default = 128)

RED2 FINE NO DMX

Range 0-255 (Default = 128)

GREEN2 FINE NO DMX

Range 0-255 (Default = 128)

BLUE2 FINE NO DMX

Range 0-255 (Default = 128)

WHITE2 FINE NO DMX

Range 0-255 (Default = 128)

INT2 FINE NO DMX

Range 0-255 (Default = 128)

RED3 NO DMX

Range 0-255 (Default = 128)

GREEN3 NO DMX

Range 0-255 (Default = 128)

BLUE3 NO DMX

Range 0-255 (Default = 128)

WHITE3 NO DMX

Range 0-255 (Default = 128)

INT3 NO DMX

Range 0-255 (Default = 128)

RED3 FINE NO DMX

Range 0-255 (Default = 128)

GREEN3 FINE NO DMX

Range 0-255 (Default = 128)

BLUE3 FINE NO DMX

Range 0-255 (Default = 128)

WHITE3 FINE NO DMX

Range 0-255 (Default = 128)

INT3 FINE NO DMX

Range 0-255 (Default = 128)

RED4 NO DMX

Range 0-255 (Default = 128)

GREEN4 NO DMX

Range 0-255 (Default = 128)

BLUE4 NO DMX

Range 0-255 (Default = 128)

WHITE4 NO DMX

Range 0-255 (Default = 128)

INT4 NO DMX

Range 0-255 (Default = 128)

RED4 FINE NO DMX

Range 0-255 (Default = 128)

GREEN4 FINE NO DMX

Range 0-255 (Default = 128)

BLUE4 FINE NO DMX

Range 0-255 (Default = 128)

WHITE4 FINE NO DMX

Range 0-255 (Default = 128)

INT4 FINE NO DMX

Range 0-255 (Default = 128)

La pagina sta caricando ...

DTS X-BRICK Outdoor RGBW Fluter, IP65 Manuale utente

Questo manuale è adatto anche per

DTS X-BRICK Outdoor RGBW Fluter, IP65 Manuale utente

in altre lingue

Documenti correlati

Altri documenti