Intel 520T Manuale utente

Intel

®

Express 520T

Switch

User Guide

717285-002

500.book Page i Thursday, September 2, 1999 1:17 PM

Year 2000 capable

An Intel product, when used in accordance with associated documentation, is “Year 2000 Capable” when, upon installation, it ac-

curately stores, displays, processes, provides, and/or receives data from, into, and between the twentieth and twenty-first centuries,

including leap year calculations, provided that all other technology used in combination with said product properly exchanges date

data with it.

Intel Corporation, 5200 NE Elam Young Parkway, Hillsboro, OR 97124-6497

Intel Corporation assumes no responsibility for errors or omissions in this manual. Nor does Intel make any commitment to up-

date the information contained herein.

* Other product and corporate names may be trademarks of other companies and are used only for explanation and to the owners’

benefit, without intent to infringe.

Second edition August 1999 717285-002

500.book Page ii Thursday, September 2, 1999 1:17 PM

iii

Contents

Chapter 1 Intel Express 520T Switch 1

Introduction to the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Positioning and Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing a Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Other Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

The Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Other LEDs on the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 2 Intel Device View 17

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Removal of Intel Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Using Intel Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Before a switch is contacted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

After a Switch or Stack is Contacted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Setting the Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installing and Managing Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Device Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Device View (Main Display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Diagnostics Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Trap Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

System Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Errors Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

500.book Page iii Thursday, September 2, 1999 1:17 PM

iv

CONTENTS

Chapter 3 Standard Configuration 41

Changing the Setup of the Switch or Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Internet Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Local Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Permanent Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Local Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Adaptive Forwarding Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Changing the Setup of the Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

General Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Port Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Port Specific Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Chapter 4 Advanced Configuration 65

VLANs (Virtual LANs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

IGMP pruning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Chapter 5 Managing the Switch 71

Management using Intel Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Information about the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Monitoring the Switch’s Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Monitoring using RMON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Monitoring the Stack’s Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Monitoring VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Monitoring the Port’s Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Tools for the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Report Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Recovery Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

DNS IP Conversion Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

500.book Page iv Thursday, September 2, 1999 1:17 PM

v

CONTENTS

Tools for the Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Stack Synchronization Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Switch Position Organizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Color Code Matrix Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Chapter 6 Technical Specifications 99

Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Chapter 7 Console Port Use and Troubleshooting 105

Use of the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Recovering from Start-up Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Using Maintenance Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Troubleshooting Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Troubleshooting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Isolating the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Further Evaluation of the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Typical Problems and Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Start-up Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Performance Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Communication Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Reporting the Problem to Intel Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Retrieving Information for Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Appendix A Limited Hardware Warranty 119

Limited Hardware Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Limited Hardware Warranty (Europe only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Federal Communications Commission (FCC) Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Manufacturer Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

AVERTISSEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

WARNUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

AVVERTENZA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

ADVERTENCIAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Automated Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Customer Support Technicians . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

500.book Page v Thursday, September 2, 1999 1:17 PM

500.book Page vi Thursday, September 2, 1999 1:17 PM

vii

Information sources for

this switch

This User Guide is one of three sources of information delivered with

this switch.

Quick Start description A printed guide that describes these basic steps:

•

Connect the switch

•

Start the switch (using the default settings)

•

Start Intel Device View

•

Change the setup

•

Save a new setup to the memory

•

Access Local Management

•

And, the legal declarations and warnings

User Guide description

(this guide)

A printed guide containing full instructions on how to install the

switch and operate the switch using Intel Device View.

Help description Online, context-sensitive help text for each dialog box, providing in-

formation about the permitted limits for the parameters used.

Information type... Given in...

Getting started quickly Quick Start (printed)

How to customize your switch User Guide (printed)

Context sensitive help Help (online)

Preface

500.book Page vii Thursday, September 2, 1999 1:17 PM

viii

PREFACE

viii

Warning

Electrostatic Sensitive Device

Products covered This User Guide gives you instructions on how to use:

•

Intel Express 520T Switch

•

Intel Device View

Prerequisite knowledge This User Guide is intended for personnel authorized to configure and

manage local area networks. We assume that the person has an ad-

vanced technical background within data communication and net-

works.

Opening this product must be done only by a network manager or per-

son who is qualified and authorized to install electrical equipment,

and who is aware of the hazards to which he/she is exposed. This per-

son must have an advanced technical background within data com-

munications and networks.

Conventions in this manual This manual uses the following conventions:

File names, commands and examples

All file names, commands and examples are shown in the COURIER

typeface.

Menu and submenu names

Menus, for example File or View, are shown in normal typeface with

lowercase and uppercase letters displayed as shown on the screen.

0887

Electrostatic Sensitive Device

Do not handle the printed circuit board unless the working area is static-free!

500.book Page viii Thursday, September 2, 1999 1:17 PM

ix

PREFACE

Access to submenus

You access submenus using a menu hierarchy. These are shown by

use of angle brackets and the courier typeface. For example,

File>Configuration>Setup shows that to select the Setup sub-

menu you must first click File and then Configuration.

Acronyms ARP Address Resolution Protocol

ASIC Application-Specific Integrated Circuit

AUI Attachment Unit Interface

BPDU Bridge Protocol Data Unit

CRC Cyclic Redundancy Check

DHCP Dynamic Host Configuration Protocol

ICMP Internet Control Message Protocol

IGMP Internet Group Message Protocol (for IP Multicast)

IEEE Institute of Electrical and Electronic Engineers

IP Internet Protocol

LAN Local Area Network

MIB Management Information Base

RAM Random Access Memory

RMON Remote Monitoring

RIP Routing Information Protocol

RSVP Resource Reservation Protocol

SNMP Simple Network Management Protocol

STP Spanning Tree Protocol

TFTP Trivial File Transfer Protocol

ToS Type of Service

UDP User Datagram Protocol

VLAN Virtual Local Area Network

500.book Page ix Thursday, September 2, 1999 1:17 PM

x

500.book Page x Thursday, September 2, 1999 1:17 PM

1

In this chapter This chapter covers the following topics.

1

Intel Express 520T

Switch

Topic See Page

Introduction to the product 2

Front Panel 3

Rear Panel 5

Installation 5

500.book Page 1 Thursday, September 2, 1999 1:17 PM

2

C H A P T E R 1 Intel Express 520T Switch

2

Introduction to the product

Purpose of the switch The Intel Express 520T Switch uses your existing network cables to

integrate switching technology into your computer network.

Each device in a workgroup or a network segment can communicate

at a full wire-speed of 10Mbps or 100Mbps to provide:

• High-speed connectivity

• Simultaneous two-way communication between connected

devices

• Increased network throughput and performance

• Increased server availability

Physical features This switch offers the following features:

• Plug-and-play—no need to configure the module to use the basic

operations

• 12 x 10/100Mbps connections

• Two option slots for modules

• Front panel LEDs that show switch, port and traffic status

• Automatic detection of 110V and 240V power supplies

Hardware features The switch offers the following features:

• Each port can operate in one of three switching modes: cut-

through, fragment-free or store-and-forward

• Each port supports half- and full-duplex operation

• Simultaneous full wire-speed switching on all ports

• RMON support for Statistics, History, Alarm and Events

• Spanning tree support on all ports

• Flow control

• Permanent MAC address entries

500.book Page 2 Thursday, September 2, 1999 1:17 PM

3

C H A P T E R 1 Intel Express 520T Switch

Software features

The switch offers the following features:

• Intel Device View for Windows* 95, Windows* 98 and Windows

NT* or Intel Device View for Web

• Adaptive forwarding mode

• Local Management via a direct terminal connection or via TEL-

NET

• SNMP Management support

• BOOTP and TFTP support

• Control over user access rights

• Creation of virtual LANs

• Stand-alone (per switch or stack) or distributed (switch network)

VLAN

• IGMP Pruning

Front Panel

Introduction The LEDs on the front panel show the status of the ports, so you

should position the switch with the front panel facing you. You can

also see which ports the cables are connected to on the switch.

View of the front panel The front panel of the switch is shown below:

1733

Power

Intel E xpress

®

520T Sw itch

Status

Temperature

RPS

123 87654 9 10 11 12

Reset

Console

9600-8-N-1

SlotBSlot A

Blink Activity Collision

Solid Link Disable

LEDsGreenOrange

PortStatus

Solid 100Mbps Fullduplex

Off 10Mbps Halfduplex

LEDsGreenOrange

500.book Page 3 Thursday, September 2, 1999 1:17 PM

4

C H A P T E R 1 Intel Express 520T Switch

4

Front panel ports

These ports are on the front panel:

Slots for modules After removing one or both of the cover plates, the modules can be

inserted to expand the functionality of the switch.

Front panel LED functions The LEDs on the front panel have the following functions:

Buttons The buttons on the front panel have the following functions:

Port Function

CONSOLE port

(DB-9)

Connects a PC (running a VT100 emula-

tion), a VT100 terminal or a modem to

access the built-in Local Management pro-

gram.

12 x 10/100Base-

TX ports (RJ-45)

Connects devices using Unshielded Twisted

Pair (UTP) cabling complying to EIA568A

Category 5 or ISO/IEC 11801 Category 5

level D.

LED

Shows the status for...

Port LEDs -

Green and Orange

The operation of each port.

Status The operation of the switch.

Power The internal power supply.

Temperature The internal temperature.

RPS (redundant

power supply)

The external, redundant power supply.

Button name Function

Port Status Shows the operational status of each port.

Reset Reset or enter Maintenance Mode or Recov-

ery Mode

500.book Page 4 Thursday, September 2, 1999 1:17 PM

5

C H A P T E R 1 Intel Express 520T Switch

Rear Panel

Introduction The rear panel has a cooling fan outlet and the main supply cable, so

you should position the switch with the rear panel facing away from

you.

View of rear panel The rear panel of the switch is shown below:

Rear panel parts The switch’s rear panel has the following parts:

Installation

Important You must adhere to all local and national regulations governing the

installation and connection of electrical devices when installing the

switch.

1741

Input

100-120VAC/2A

200-240VAC/1A

47Hz-63Hz

Redundant Power Supply (RPS)

Part Function

Fan outlet Cools the internal circuitry of the switch.

Power connection A socket to connect the power cord to the

main supply.

Redundant power

supply connector

Connects an external redundant power sup-

ply. If the internal power supply fails, the

redundant power supply starts immediately.

500.book Page 5 Thursday, September 2, 1999 1:17 PM

6

C H A P T E R 1 Intel Express 520T Switch

6

Before Installation

Contents of the pack Unpack the switch carefully and check that these parts are present:

Check the package

contents

If you have not received all of the parts, or any of the parts are dam-

aged, contact your dealer immediately.

Keep all the packaging materials in case you need to repack the

switch.

Check all labels Read all labels and rating plates on the switch. If there is anything that

you do not understand, or if any of the information provided does not

appear to comply with your local or national rules and regulations,

consult your dealer before proceeding with the installation.

Essential reading It is important that you read the following:

• “Late-breaking News”.

This contains essential information you should be aware of when

installing and using the product; for example, limitations and

compatibility issues.

• Warnings and the instructions earlier in this guide.

• The README.TXT file on the CD-ROM. This gives a general

description of the software and specific requirements.

Item Present?

One Intel Express 520T Switch

One power cord (suitable for your

power outlet)

One mounting kit

One CD-ROM

One Console cable

One Quick Start

One User Guide (you are reading it)

Late-breaking News

Intel Support Service papers

500.book Page 6 Thursday, September 2, 1999 1:17 PM

7

C H A P T E R 1 Intel Express 520T Switch

Positioning and Installing the Switch

Allow adequate ventilation The switch contains two fans to air-cool the internal circuitry. The air

is drawn in from the left of the unit and expelled through the outlet

grills on the right side and the rear.

To ensure correct airflow, leave 100 mm (4 inches) free space on both

sides and behind the switch. Do not allow the intake or outlet grills to

become blocked.

On a desktop To install the switch in a desktop environment:

1 Find the four rubber feet in the pack that contains the rack

mounting kit.

2 Remove the backing strip from each of the four feet.

3 Attach the four rubber feet to the underside of the switch (to

ensure that the switch stands firmly).

4 Place the switch on a stable, flat surface.

5 Ensure that the air intake (on the left) and fan outlets (on the

right side and rear) are not blocked.

Warning The switch’s lifetime and operational reliability can

be seriously degraded by inadequate cooling.

Rack requirements Install the switch in a standard rack in accordance with IEC297 (or

similar); if the minimum outside measurements of the rack are 600 x

600mm (23.5 x 23.5inches), you must allow 190mm (7.5 inches) of

space at the rear.

Mounting kit The switch is delivered with a kit to attach it to a standard 19-inch

equipment rack (with side support rails). The kit contains two mount-

ing brackets and four screws (for attaching the brackets to the sides

of the switch).

Tools required for

positioning in a rack

In addition to the mounting kit, you need the following items to

mount the switch in a rack:

• Standard 19-inch rack with side support rails.

• 3 mm screwdriver.

500.book Page 7 Thursday, September 2, 1999 1:17 PM

8

C H A P T E R 1 Intel Express 520T Switch

8

• Customer-supplied screws for securing the switch in the rack.

Mounting screws are not provided because the required sizes

may vary from rack to rack.

In an equipment rack To mount the switch in a standard equipment rack:

1 Attach the mounting bracket marked “Left” to the left-hand side

of the switch, and attach the mounting bracket marked “Right”

to the right-hand side of the switch, using the four screws pro-

vided.

Make sure that you attach the mounting brackets to the correct

sides. Otherwise the switch will not align correctly in the

equipment rack.

2 If the four rubber feet prevent the switch from standing firmly

on the equipment rack’s side support rails, remove them.

3 Set the switch in the equipment rack, and make sure there is

adequate space for air flow around the switch (see “Allow ade-

quate ventilation” in “Positioning and Installing the Switch”, p.

7).

4 Screw the mounting brackets securely to the equipment rack.

Ambient temperature If the switch is installed in a closed or multi-rack assembly, the oper-

ating ambient temperature of the rack environment may be greater

than the ambient temperature of the room. Make sure that the temper-

ature of the rack environment does not exceed the recommended op-

erating temperature for the switch.

1734

P

o

w

e

r

Intel Express

®

520T Switch

Sta

t

u

s

Te

m

p

e

r

a

t

u

r

e

R

P

S

123

87654

91

0

11 1

2

R

e

s

e

t

C

o

n

s

o

le

9

6

0

-

8

-

N

-

1

S

lo

t

B

S

l

o

t

A

B

lin

k

A

c

tiv

ity

C

o

llis

ion

S

o

lid

L

in

k

D

is

a

b

le

L

E

D

s

G

re

e

n

O

ra

n

g

e

Port Status

S

o

lid

10

0

M

bp

s

F

u

ll

d

u

p

le

x

O

f

f1

0

M

b

p

sH

a

lf

du

p

le

x

L

E

D

s

G

re

e

n

O

ra

n

g

e

500.book Page 8 Thursday, September 2, 1999 1:17 PM

9

C H A P T E R 1 Intel Express 520T Switch

Installing a Module

Introduction You can increase the connectivity options of your switch by installing

a module.

Warning Modules are not designed to be installed in, or removed

from, the switch while it is in operation. You must

power off the switch before attempting to install or

remove a module.

Static-free working area The module’s printed circuit board is an Electrostatic Sensitive De-

vice and should be handled only in a static-free working area; other-

wise, the printed circuit board may fail or be degraded.

Avoiding damage to the

circuit board

If you remove the plate covering the slot on the front of the switch,

for example, to install or remove a module, follow this procedure to

avoid damage to your printed circuit board:

Warning Do not remove the plate unless the switch is discon-

nected from the main power supply.

1 Disconnect the switch from the main power supply.

2 Ground the switch before you handle the printed circuit board.

3 Connect yourself to a non-painted/non-isolated part of the

grounded switch (for example the back panel) using a wrist

strap with 1MΩ resistance to ensure that you carry the same

electrostatic charge as the enclosure.

4 Remove the plate covering the slot.

Installing a module To install a module:

1 If the switch is already operational, disconnect it from the main

power supply.

2 Follow the instructions in “Avoiding damage to the circuit

board” above.

3 Unscrew the screws of the plate covering the slot on the front of

the switch. Save these screws and plate.

4 Insert the module into the slot (following the instructions in the

module’s User Guide). Place your thumbs just beneath the

screws on the front panel of the module and push in the module.

Secure it using the retaining screws.

500.book Page 9 Thursday, September 2, 1999 1:17 PM

10

C H A P T E R 1 Intel Express 520T Switch

10

Removing the module

To remove a module:

1 If the switch is already operational, disconnect it from the main

power supply.

2 Follow the instructions in “Avoiding damage to the circuit

board” above.

3 Unscrew the screws securing the module.

4 Pull the module gently to disengage the connectors fully from

the socket on the motherboard. Slide the module out com-

pletely.

5 Cover the empty module port with the plate and secure using

the screws.

Connecting Other Devices

Introduction Incorrect cabling is often the cause of network configuration prob-

lems

Use shielded cables Shielded cables normally comply with EMC and FCC emission lim-

its.

Only use unshielded cables when it is explicitly specified in the in-

stallation manual of the device in question.

Cables for the LAN Ports Ports on the switch are wired MDI-X, so use the following cable:

If you connect the switch to a... Then use a...

Workstation or server Straight-through cable 1:1

Device with MDI-X ports (for exam-

ple another Intel switch or hub)

Crossover cable

Device with MDI ports Straight-through cable 1:1

500.book Page 10 Thursday, September 2, 1999 1:17 PM

La pagina sta caricando ...

Intel 520T Manuale utente

Questo manuale è adatto anche per

Intel 520T Manuale utente

in altre lingue

Documenti correlati

Altri documenti