Lenovo Aptiva Hardware Maintenance Manual

Hardware Maintenance Service

for Service Level A

Machine Type 2274

First Edition (May, 2000)

The following paragraph does not apply to any state

or country where such provisions are inconsistent

with local law: INTERNATIONAL BUSINESS

MACHINES CORPORATION PROVIDES THIS

PUBLICATION “AS IS” WITHOUT WARRANTY OF

ANY KIND, EITHER EXPRESSED OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.

References to IBM products, programs, or services

do not imply that IBM intends to make them available

outside the United States. This publication could

include technical inaccuracies or typographical

errors. Changes are periodically made to the

information herein; these changes will be made in

later editions. IBM may make improvements and/or

changes in the product(s) and/or the program(s) at

any time. Address comments about this publication to

IBM Corporation, Dept. E23/962-2, 455 Park Place,

Lexington, KY 40511-1856, USA. Information you

supply may be used by IBM without obligation. For

copies of publications related to this product, call toll

free 1-800-IBM-7282 in the Continental U.S.A. In

Canada, call toll free 1-800-465-7999.

Corporation 2000.

Note to U.S. Government Users - Documentation

related to restricted rights - Use, duplication or

disclosure is subject to restrictions set forth in GSA

ADP Schedule Contract with IBM Corp.

iii

Contents

Contents ..............................................................iii

Notices ................................................................vii

Safety Information ................................................viii

Laser Compliance Statement..............................xxxi

Trademarks .......................................................xxxii

Preface .............................................................xxxiii

General Information .............................................1

Introduction ............................................................2

Product Overview ...................................................3

Processor ........................................................3

Memory ...........................................................3

External Ports ..................................................4

Diskette Drive ..................................................4

Hard Disk Drive ...............................................4

DVD-ROM Drive ..............................................5

Multimedia .......................................................5

Power Management ........................................5

Power Supply ..................................................6

Internal Cabling ...............................................6

Monitor (Not included with some models) .......6

Keyboard .........................................................7

Mouse .............................................................7

Hardware Interfaces ...............................................8

CMOS Reset ........................................................10

Power-On Password ............................................11

Flash (BIOS) Update Procedure ..........................12

BIOS-contained Model Number and

Serial Number ......................................................13

BIOS Configuration/Setup Utility ..........................14

Working with the Setup Menus .....................14

Viewing System Information, and

Product Data .................................................17

Devices and I/O ports ....................................17

Startup Options .............................................20

Date and Time ...............................................21

Advanced Setup ............................................23

Power Management Setup ............................24

Specifications .......................................................28

Dimension (width x depth x height) ...............28

Weight ...........................................................28

Environment ..................................................28

Power consumption .......................................28

iv

Electrical input ...............................................28

Operating Requirements ......................................29

Check Procedures .............................................31

Introduction ..........................................................32

Start .....................................................................33

Index of Symptoms, Messages, Error Codes,

or Beeps ...............................................................38

Troubleshooting ...................................................54

Factory-Installed Storage Devices ................54

Factory-Installed Modem Card .............................58

Audio (Not Supported by Diagnostics Program) ..60

CD/DVD-ROM Drive ............................................63

Memory ................................................................65

Keyboard ..............................................................66

Mouse ..................................................................67

Power Supply .......................................................69

Monitor .................................................................72

Undetermined Problems ......................................74

Diagnostic Aids ..................................................77

Introduction ..........................................................78

Power-On Self Test ..............................................79

Diagnostic Diskette ..............................................81

Using the Diagnostic Diskette .......................81

Using Diagnostic Program from

Recovery CD .................................................82

Diagnostics Program Features ......................83

Repair Information .............................................85

Removals and Replacements ..............................86

Handling ESD-Sensitive Parts .............................87

Cover .............................................................90

Bay Panels.................................................... 92

Bay 1- 5.25-In. Bay

(Internal or External Access) .........................93

Bay 3 - 3.5-In. Bay

(Internal or External Access) .........................94

Bay 4 - 3.5-In. Bay

(External Access for Diskette Drive) .............94

Front Panel ....................................................96

Power Supply ................................................97

Adapter Cards ...............................................98

Memory(DIMM) .............................................99

AMD K7 Duron Processor ...........................100

System Backup Battery ...............................102

v

Indicator LED and Cable .............................103

System Board ..............................................104

Parts/Test Point Locations ..............................107

Introduction ........................................................108

System Board Jumpers and Connectors ...........109

Power Supply Connectors and Voltages ...........111

Network Cards ...................................................113

Factory-Installed Modem Card Layout ...............114

Video Cards .......................................................115

Nvidia M64 w/ TV Out, 32MB ......................115

Nvidia NV10 w/ TV Out, 32MB ....................115

3.5-In. Hard Disk Drive Jumper Settings ............117

CD-ROM Drive ...................................................119

CD-ROM Drive Rear Panel Connectors

and Jumpers ...............................................121

CD-ROM R/W Drive ...........................................122

CD-ROM R/W Drive Rear Panel

Connectors and Jumpers ............................123

DVD-ROM Drive ..........................................124

DVD-ROM Drive Rear Panel Connectors

and Jumpers ...............................................125

DIMM Configurations .........................................126

System Board Connector Pin Signals ................127

Monitor Port Signals ....................................127

Serial Port Signals .......................................127

Parallel Port Signals ....................................128

Mouse Port Signals .....................................128

Keyboard Port Signals ................................128

Diskette Drive Cable Connector Signals .....129

IDE Cable Connector Signals .....................130

Safety Inspection Guide ..................................131

General Guidelines ............................................132

Parts Catalog ....................................................133

Abbreviations .....................................................134

System Assembly ..............................................135

Assembly 1: System Unit ............................135

Assembly 2: Diskette, Hard Drive

and Zip Drive ...............................................137

Assembly 3: CD/DVD-ROM Drive ...............138

Assembly 4: Power Cord .............................139

Assembly 5: Keyboard and Mouse .............140

vi

Appendix A. FRU Number List ........................141

Appendix B. Online Support ...........................143

Index ..................................................................145

Notices vii

Notices

References in this publication to IBM products,

programs, or services do not imply that IBM intends

to make these available in all countries in which IB

operates. Any reference to an IBM product, program,

or service is not intended to state or imply that only

IBM's product, program, or service may be used. Any

functionally equivalent product, program, or service

that does not infringe any of IBM's intellectual

property rights, or other legally protectable rights,

may be used instead of the IBM product, program, or

service. References in this publication to IBM

products, programs, or services are purely hardware-

related and do not cover circumstances of software

problems. Evaluation and verification of operation in

conjunction with other products, program, or services,

except those expressly designated by IBM are the

user's responsibility.

IBM may have patents or pending patent applications

covering subject matter in this document. The

featuring of these patents, pending or otherwise, in

this document does not give you any license to these

patents. You can send license inquires, in writing, to

the IBM director of Commercial Relations, IBM

Corporation, Purchase, NY10577.

Voltage Supply Switch Settings

Your IBM Personal Computer might have voltage

switches, which must be set correctly for your voltage

supply. If your monitor or system unit has a voltage

switch, complete these steps to make sure each

switch is set correctly:

1. Determine the correct voltage switch setting for

your area:

2. Locate the voltage switch on the back of your

monitor or system unit. If the setting shown on the

switch is:

•

Correct: start setting up your IBM computer.

•

Incorrect: change the voltage switch setting.

Voltage Supply Range Voltage Switch Setting

100-127 V 115 V

200-240 V 230 V

viii

Safety Information

DANGER

To avoid a shock hazard, do not connect or

disconnect any cables or perform installation,

maintenance, or reconfiguration of this product during

an electrical storm.

To avoid shock hazard:

•

The power cord must be connected to a properly

wired and earthed receptacle.

•

Any equipment to which this product will be

attached must also be connected to properly wired

receptacles.

When possible, use one hand to connect or

disconnect signal cables to prevent a possible shock

from touching two surfaces with different electrical

potentials.

Electrical current from power, telephone, and

communications cables is hazardous. To avoid shock

hazard, connect and disconnect cables as described

following when installing, moving, or opening covers

of this product or attached devices.

IMPORTANT:

When replacing the battery, use only IBM Part

Number 33F8354 or an equivalent type battery

recommended by the manufacturer. If your

system has a module containing a lithium

battery, replace it only with the same module

type made by the same manufacturer. The

To Connect

1. Turn Everything OFF.

2. First, attach all cables to

devices.

3. Attach signal cables to

receptacles.

4. Attach power cord(s) to

outlet.

5. Turn device ON

To Disconnect

1. Turn Everything OFF.

2. First, remove power

cord(s) from outlet.

3. Remove signal cables

from receptacles.

4. Remove all cables from

devices.

Notices ix

battery contains lithium and can explode if not

properly used, handled, or disposed of.

Do not:

•

Throw or immerse into water

•

Heat to more than 100°C (212°F)

•

Repair or disassemble

Dispose the battery as required by local ordinances

or regulations.

IMPORTANT:

When a CD-ROM drive is installed, note the following.

Use of controls or adjustments or performance of

procedures other than those specified herein might

result in hazardous radiation exposure.

Removing the covers of the CD-ROM drive could

result in exposure to hazardous laser radiation. There

are no serviceable parts inside the CD-ROM drive.

Do not remove the CD-ROM drive covers.

DANGER

Some CD-ROM drives contain an embedded Class

3A or Class 3B laser diode. Note the following.

Laser radiation when open. Do not stare into the

beam, do not view directly with optical instruments,

and avoid direct exposure to the beam.

IMPORTANT:

Electrical current from power, telephone, and

communication cables can be hazardous. To avoid

personal injury or equipment damage, disconnect the

attached power cords, telecommunications systems,

networks, and modems before you open the server

covers, unless instructed otherwise in the installation

and configuration procedures.

x

PERIGO:

Para evitar choques elétricos, não conecte ou

desconecte nenhum cabo, nem efetue instalação,

manutenção ou reconfiguração deste produto

durante uma tempestade com raios.

Para evitar choques elétricos:

•

O cabo de alimentação deve ser conectado a um

receptáculo corretamente instalado e aterrado.

•

Todos os equipamentos aos quais este produto

será conectado devem também ser conectados a

receptáculos corretamente instalados.

Quando possível, utilize uma das mãos para

conectar ou desconectar cabos de sinal, para evitar

um possível choque ao tocar duas superfícies com

potenciais elétricos diferentes.

A corrente elétrica proveniente de cabos de

alimentação, de telefone e de comunicação é

perigosa. Para evitar choques elétricos, conecte e

desconecte os cabos conforme descrito a seguir, ao

instalar, movimentar ou abrir tampas deste produto

ou de dispositivos conectados.

Para Conectar

1.DESLIGUE tudo.

2.Conecte primeiro todos

oscabos nosdispositivos.

3.Conecte os cabos de sinal

nos receptáculos.

4.Conecte o(s) cabo(s) de

alimentação nas

tomadas.

5.LIGUE o dispositivo

Para Desconectar

1.DESLIGUE tudo.

2.Remova primeiro o(s)

cabo(s) de alimentação

das tomadas.

3.Remova os cabos de sinal

dos receptáculos.

4.Remova todos os cabos

dos dispositivos

Notices xi

CUIDADO:

Ao substituir a bateria, utilize apenas o Número de

Peça IBM 33F8354 ou um tipo de bateria equivalente

recomendado pelo fabricante. Se seu sistema

possuir um módulo com uma bateria de lítio,

substitua-o apenas pelo mesmo tipo de módulo,

produzido pelo mesmo fabricante. A bateria contém

lítio e pode explodir se não for utilizada, manuseada

e descartada de forma adequada.

Não:

•

Jogue ou coloque na água

•

Aqueça a mais de 100°C (212°F)

•

Conserte nem desmonte.

Descarte a bateria conforme requerido pelas

disposições e regulamentações locais.

CUIDADO:

Quando uma unidade de CD-ROM estiver instalada,

observe o seguinte.

A utilização de controles ou ajustes ou a execução de

procedimentos diferentes daqueles especificados

nesta publicação pode resultar em exposição

perigosa à radiação.

A remoção das tampas da unidade de CD-ROM pode

resultar em exposição a radiação perigosa de laser.

Não existem peças que possam ser consertadas no

interior da unidade de CD-ROM. Não remova as

tampas da unidade de CD-ROM.

PERIGO:

Algumas unidades de CD-ROM contém um diodo de

laser da Classe 3A ou da Classe 3B. Observe o

seguinte.

Radiação de laser quando aberto. Não olhe

diretamente para o feixe de laser, não olhe

xii

diretamente com instrumentos óticos, e evite

exposição direta ao raio.

CUIDADO:

A corrente elétrica proveniente de cabos de

alimentação, de telefone e de comunicação é

perigosa. Para evitar ferimentos pessoais ou danos

aos equipamentos, desconecte os cabos de

alimentação, sistemas de telecomunicação, redes e

modems antes de abrir as tampas do servidor, a

menos que receba outras instruções nos

procedimentos de instalação e configuração.

Notices xiii

xiv

Notices xv

xvi

Notices xvii

PERIGO:

Pour éviter tout risque de choc électrique, ne

manipulez aucun câble et n'effectuez aucune

opération d'installation, d'entretien ou de

reconfiguration de ce produit au cours d'un orage.

Pour éviter tout risque de choc électrique :

•

Les cordons d'alimentation du présent produit et

de tous les appareils qui lui sont connectés doivent

être branchés sur des socles de prise de courant

correctement câblés et mis à la terre.

Afin d'éviter tout risque de choc électrique provenant

d'une différence de potentiel de terre, n'utilisez

qu'une main, lorsque cela est possible, pour

connecter ou déconnecter les cordons d'interface.

Le courant électrique passant dans les câbles de

communication, ou les cordons téléphoniques et

d'alimentation peut être dangereux. Pour éviter tout

risque de choc électrique, lorsque vous installez ou

que vous déplacez le présent produit ou des

périphériques qui lui sont raccordés, reportez-vous

aux instructions ci-dessous pour connecter et

déconnecter les différents cordons.

Connexion

1. Mettez les unités hors

tension.

2. Commencez par

brancher tous les

cordons sur les unités.

3. Branchez les câbles

d'interface sur les prises.

4. Branchez les cordons

d'alimentation sur un

socle de prise de

courant.

5. Mettez les unités sous

tension.

Déconnexion

1. Mettez les unités hors

tension.

2. Commencez pas

débrancher les cordons

alimentation des socles

de prise de courant.

3. Débranchez les câbles

d'interface des prises.

4. Débranchez tous les

câbles des unités.

xviii

ATTENTION:

Remplacez la pile usagée par une pile de référence

identique exclusivement - voir la référence IBM - ou

par une pile équivalente recommandée par le

fabricant. Si votre système est doté d'un module

contenant une pile au lithium, vous devez le

remplacer uniquement par un module identique,

produit par le même fabricant. La pile contient du

lithium et présente donc un risque d'explosion en cas

de mauvaise manipulation ou utilisation.

•

Ne la jetez pas à l'eau.

•

Ne l'exposez pas à une température supérieure à

100°C.

•

Ne cherchez pas à la réparer ou à la démonter.

Pour la mise au rebut, reportez-vous à la

réglementation en vigueur.

ATTENTION:

Si une unité de CD-ROM est installée, prenez

connaissance des informations suivantes :

Pour éviter tout risque d'exposition au rayon laser,

respectez les consignes de réglage et d'utilisation

des commandes, ainsi que les procédures décrites

dans le présent document.

Pour éviter une exposition directe au rayon laser,

n'ouvrez pas l'unité de CD-ROM. Vous ne pouvez

effectuer aucune opération de maintenance à

l'intérieur.

PERIGO:

Certaines unités de CD-ROM contiennent une diode

laser de classe 3A ou 3B. Prenez connaissance des

informations suivantes :

Rayonnement laser lorsque le carter est ouvert.

Évitez de regarder fixement le faisceau ou de

Notices xix

l'observer à l'aide d'instruments optiques. Évitez une

exposition directe au rayon.

ATTENTION:

Le courant électrique circulant dans les câbles de

communication et les cordons téléphoniques et

d'alimentation peut être dangereux. Pour votre

sécurité et celle de l'équipement, avant de retirer les

carters du serveur, mettez celui-ci hors tension et

déconnectez ses cordons d'alimentation, ainsi que

les câbles qui le relient aux réseaux, aux systèmes

de télécommunication et aux modems (sauf

instruction contraire mentionnée dans les procédures

d'installation et de configuration)

.

xx

VORSICHT:

Aus Sicherheitsgründen bei Gewitter an diese

Gerät keine Kabel anschließen oder lösen. Ferner

keine Installations-, Wartungs- oder

Rekonfigurationsarbeiten durchführen.

Aus Sicherheitsgründen:

•

Gerät nur an eine Schutzkontaktsteckdose mit

ordnungsgemäß geerdetem Schutzkontakt

anschließen.

•

Alle angeschlossenen Geräte ebenfalls an

Schutzkontaktsteckdosen mit ordnungsgemäß

geerdetem Schutzkontakt anschließen.

Signalkabel möglichst einhändig anschließen oder

lösen, um einen Stromschlag durch Berühren von

Oberflächen mit unterschiedlichem elektrischem

Potential zu vermeiden.

Elektrische Spannungen von Netz-, Telefon- und

Datenübertragungsleitungen sind gefährlich. Um

einen Stromschlag zu vermeiden, nur nach den

Anweisungen arbeiten, die für Installation, Transport

oder Öffnen von Gehäusen dieses Produkts oder

angeschlossenen Einheiten gelten.

Kabel anschließen

1.Alle Geräte ausschalten

und Netzstecker ziehen.

2.Zuerst alle Kabel an

Einheiten anschließen.

3.Signalkabel an

Anschlußbuchsen

anschließen.

4.Netzstecker an Steckdose

anschließen.

5.Gerät einschalten.

Kabel lösen

1.Alle Geräte ausschalten.

2.Zuerst Netzstecker von

Steckdose lösen.

3.Signalkabel von

Anschlußbuchsen lösen.

4.Alle Kabel von Einheiten

lösen.

La pagina sta caricando ...

Lenovo Aptiva Hardware Maintenance Manual

Questo manuale è adatto anche per

Lenovo Aptiva Hardware Maintenance Manual

in altre lingue

Documenti correlati

Altri documenti