CET LHM62 Manuale del proprietario

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 1

CET

VISUALIZED DIGITAL

TIMER PAUSE / WORK

Type:

LHM62

THE INSTRUMENTS OF SERIES LHM ARE PAUSE /

WORK DIGITAL TIMERS WIDE USABLE IN THE

INDUSTRY FOR THEIR PROGRAMMABLE

CHARACTERISTICS AND THE FLEXIBILITY OF

THEIR EMPLOYMENT.

TIMER LHM62 IS A CYCLICAL PAUSE / WORK THAT

FINDS APPLICATION WHERE THERE IS THE

NECESSITY TO EXECUTE CYCLES OF TWO

ALTERNATED TIMINGS.

GENERAL CHARACTERISTICS

PROGRAMMABLE PARAMETERS

• Frontal keyboard in polycarbonate (antiscratch, antioil,

antacid).

• IP65 protection degree

• Accessible parameters with key software

• Removable terminals connection.

• Execution DIN 48 X 96.

• Recessed assembly.

• Special retaining brackets.

• One Pause and one Work Set Point

• 4 Time Scales

• UP / DOWN Timing

• Memory

• Timing Start in Pause or in Work Mode

• START Input Selection

• Operating in Automatic or Single Cycle

• OUTPUT mode selection

• Cycles Predeterminator

DESCRIPTION OF THE OPERATION

In the Timer type LHP the choice of the scale time is valid for both the timing. Selecting the START departure in Pause or Work and

the timing in UP or DOWN the instrument gets ready in order to work. In Automatic operation the timing begins to the input START

closing. Between the two timings it is possible to execute a programmable intermediate time.

TECHNICAL CHARACTERISTICS

•

POWER SUPPLY IN ALTERNATE CURRENT

•

POWER SUPPLY IN DIRECT CURRENT

•

POWER SUPPLY TOLERANCE

•

ABSORPTION

•

OPERATING TEMPERATURE

•

CLIMATIC CONDITIONS

•

TIMING VISUALIZATION

•

TIMINGS SCALES

•

START INPUT

•

AUXILIARY INPUTS POWER SUPPLY

•

COMMAND IMPUTS

•

OUTPUTS

•

RELAY RESET

•

PROGRAMMED DATA MEMORY

: Single power 24 - 110 - 230 Vac (50 / 60 Hz).

: Single power 24 Vdc

: +10% - 15%.

: 2 W - 3 VA.

: -5 °C + 55 °C.

: U.R. 95 % at 40 °C (without condensate).

: 6 digits, 14mm high

: 9999h59m - 99h59m59s - 99m59s99c - 9999s99c

: programmable as Continuous; Impulsive, Start/Stop

: 24 Vdc - 80 mA available on terminals.

: 1 Start - 1 Reset Timing - 1 Inhibit Timing (Inhibit).

: 2 relays with operating contacts; capacity 2A - 250Vac.

: manual

: static (without battery)

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 2

DESCRIPTION OF THE FRONTAL KEYBOARD

ø

YELLOW

The key 'LEFT ARROW' in normal operating phase visualizes, blinking, all the programmings executed without the

limitation of the insertion code. The time of scansion of the programmings is given from the pressure of the same

key. It exits automatically from this phase after 5 sec of the last pressure of the same key.

In programming phase it moves the cursor of the figure towards left of a step, than at the beginning it is on the right

side first one on the. At the end it resumes from the first one to right.

ù

YELLOW

The key 'UP ARROW' in normal operating phase it enter and exit to the Cycle Predeterminator.

In programming phase it increases the value of the blinking figure.

ú

BLUE

The key 'PRG' pressed for 2 sec. allows to enter in the programming phase, visualizing on display C.0000.

In the programming phase, pressing key 'PRG' impulsively, it exits from the programming phase. The instrument

exits automatically from the programming phase, 60 sec. after the pressure of the last key.

û

RED

The key 'ENT/RES' in normal phase of counting has the 'RESET' function, with the modalities to it attributed in the

programming phase.

In programming phase it confirms and memorizes the visualized data and passes to the successive function. If it has

arrived to list end it resumes from the beginning.

INPUTS / OUTPUTS DESCRIPTION

DC POWER

(inputs 1-2) 24VDC Power Supply Input of the instrument.

AC POWER

(inputs 3-4) AC Power Supply Input of the instrument; it can be to 24 - 110 - 230 VAC in according to demand.

24 VDC - 80mA

(inputs 5-6) 24 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and amplified

proximity.

START

(inputs 7) START Input that execute the timing starting as the programming mode; it’s configurable in Positive

(PNP) or Negative (NPN) logic by the dip switches on the rear.

RESET

(inputs 8) RESET Input that execute the timing reset; it’s configurable in Positive (PNP) or Negative (NPN) logic

by the dip switches on the rear.

INHIBIT

(inputs 9) INHIBIT Input that execute the timing Inhibit; it’s configurable in Positive (PNP) or Negative (NPN) logic

by the dip switches on the rear.

RL2

(inputs 10 - 11) Output of Relay RL2, connected to the operation of the WORK timing. The Common, normally Close

and normally Open contacts are available.

RL1

(inputs 12 - 13) Output of Relay RL1, connected to the operation of the PAUSE timing. The Common, normally Close

and normally Open contacts are available.

DESCRIPTION OF THE LED’S OPERATION

LED 1 It comes activated during the PAUSE timing.

LED 2 It comes activated during the WORK timing.

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 3

SET POINTS PROGRAMMING

For SET POINTS programming access, proceed as follow:

- Press key ‘PRG’ in impulsive mode; on display appears:

0¨0¨20

è

P. = Time of PAUSE, programmable between 1 cent of second and 9999h59m (depending on

the programmed scale). If programmed = 0 it automatically reprograms itself to 1 sec.

0¨0¨20

Ä

L. = Time of WORK, programmable between 1 cent of second and 9999h59m (depending on

the programmed scale). If programmed = 0 it automatically reprograms itself to 1 sec.

Key ENT confirms the data and passes to the successive programming. In order to exit the programming, press key PRG.

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key

PRG

for about 2 sec. On the display appears:

» 0000

GROUP 1

:

insert code

2357

and press

ENT

.

Ìi9²9

t.i. = Intermediate Time, programmable between 0.0 and 99.9 sec. This time comes

executed, if programmed various from 0, between the PAUSE time and the WORK time).

During the execution of this time the output is not active.

SCÄ 1

SCL. = Time Scale. Selection of the maximum time scale of the timing. It’s possible to choose

between 4 different time scales:

1 = 59m59s99c - 2 = 99h59m59s - 3 = 9999h59m - 4 = 9999s99c

Cæ UP

Cæ dæ

Count UP / DOWN / Superior.

Count = Up: the timer gets ready to visualize the timing in increasing way (UP), starting from

zero up to the programmed value of set point.

Count = dn: the

timer

gets ready to visualize the

timing

in decreasing way (DOWN), starting

from the programmed value of set point to zero.

Stê è

Stê Ä

Start in PAUSE or in WORK mode.

Str. = P. : the cycle starts executing the PAUSE time

Str. = L. : the cycle starts executing the WORK time

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key

PRG

for about 2 sec. On the display appears:

» 0000

GROUP 3

:

insert code

3210

and press

ENT

.

9999

Û

c. = CYCLES PREDETERMINATOR, programmable between 0 and 9999; with this parameter

is possible to program how many cycles of PAUSE/WORK the instrument must execute. At the

end of the cycles number, the sequence comes interrupt. To restart the sequence it is

necessary to reset the predeterminator. If the value is programmed = 0 the function is excluded

and the sequence goes to infinite. Pressing the

ù

key the display shows the decreasing value

of the predeterminator; pressing another time the key the display shows the current timing.

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 4

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key

PRG

for about 2 sec. On the display appears:

» 0000

GROUP 2

:

inset code

2413

and press

ENT

.

NeÆon

NeÆ

oF

Active or excluded memory.

This parameter allows to program the saving of the current counter value during the power off

the instrument.

MEM.on. = memorization of the count during the power off. When power on the instrument the

display will visualize the last present value in the power off phase.

MEM.of. = excluded memorization of the count; every time that the instrument comes powered

off and then powered on the count comes lost and the instrument restart always from the initial

condition.

R reË0n

R reËO

F

RESET Key ON / OFF; this programming enables and disables the RESET function of frontal

key RES during the operation of the timing.

RES.on = RESET function of key RES enabled

RES.of. = RESET function of key RES disabled

Iæ »

Iæ Á

Iæ Ë

Programming of the START Input.

This programming allows to Start the timing in three different modes:

In. I. = Impulsive Mode; the timing starts with the impulsive closing of the START input.

In. C. = Continuously Mode; the timing starts with the closing of the START input; the timing

is interrupted every time the START input comes opened.

In. S. = Start/Stop Mode; the timing starts with the impulsive closing of the START input and it

stops to the subsequent closing. Closing another time the input the timing resume and it stops

to the subsequent closing.

CYÄ ¹

CYÄ Í

Programming of the PAUSE/WORK Cycle in Automatic or Single mode

This parameter allows to program the execution of the PAUSE/WORK Cycle in Continuos

mode (AUTOMATIC) or in Single mode (UNIQUE). With the AUTOMATIC programming the

cycle goes to infinite (or for many cycles how many have been programmed with the

programming under code 3210); with the Single programming (UNIQUE) the cycle is executed

one time only and restart after a reset.

CYL. A. = execution of the cycle timing in continuos mode.

CYL. U. = execution of the cycle timing one time only.

0íÈ î

0íÈ ÷

Programming of the OUTPUT RL1. This parameter allows to activate the RL1 relay

during the timing

î

or at the end

÷

of the timing.

Ou.P.

î

= Activation of the RL1 relay during the timing

Ou.P.

÷

= Activation of the RL1 relay at the end of the timing

¹È È

¹È ê

Activation mode of the programmed parameters.

With this programming is possible to activate the executed programmings directly to the exit of

the programming or, when exited of the programming, after a RESET (with frontal key or from

rear input)

A.P. = P. Activation of the parameters to the exit of the programming.

A.P. = r. Activation of the parameters to the exit of the programming after a RESET.

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 5

DECLARATION OF ‘CE’ CONFORMITY

CE NORMATIVE CONFORMITY

Borgolavezzaro, October , 03rd 2005

The building firm:

CET s.r.l.

Head office:

Strada Statale 211, Km 53,3

28071 Borgolavezzaro (No) ITALIA

Tel. 0039 - (0)321 - 885301 Fax. 0039 - (0)321 - 885560

declare that the products:

type :

Electronic Timer

model:

LHM 62

use class:

Industrial

are in conformity with the following normatives:

EN55011

ENV50141

ENV50204

EN61000-4-2

EN61000-4-4

The manufacturing :

CET s.r.l.

________________________________

Signature

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 6

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 7

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l.

Vers. 1.0

LHM 62

Pag. 8

CONNECTIONS

INPUT SIGNALS

START START

CONTACT CONTACT

NPN PNP

START START

TTL LOGIC TTL LOGIC

NPN PNP

PROGRAMMING PROGRAMMING

NPN PNP

RESET INHIBIT

NPN NPN

RESET INHIBIT

PNP PNP

OVERALL DIMENSIONS

FRONT SIDE

REAR DRILL TEMPLATE

CET

CETCET

CET

CETCET

CET

s.r.l.

Strada Statale 211 Km 53,550

28071 Borgolavezzaro - NO - ITALY

Tel : ++39 0321-885180/885301/885807

Fax : ++39 0321-885560

info@cet-italy.com

www.cet-italy.com

Agent :

48

96

ENT

RES

PROG

L1

L2

1ª6«25

Electronic counter

LHM

CET

139

115

9

15

44x92

REMOVABLE

TERMINALS

RETAINING

BRACKETS

10

MAX

93

45

7

6

7

5

6

7

5

7

6

8

6

9

5

8

5

9

92

44

1 2 3 4 5 6 7 8 9 10 11 12 13

-

+

24 VDC AC

POWER

+

-

24 Vdc

80mA

RESET

1

2

3

4

5

6

7

9

8

13

START

RL1

INHIBIT

11

10

12

RL2

CET LHM62 Manuale del proprietario

Questo manuale è adatto anche per

CET LHM62 Manuale del proprietario

in altre lingue

Documenti correlati