Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Manuale utente

Marca: Roborock

Modello: Q7 MAX+ ROBOTSTØVSUGER, SVART

Categoria: Aspirapolvere robotici

Tipo: Manuale utente

北京石头世纪科技股份有限公司

图纸

提供

单位

材

质

工

艺

要

求

历

史

版

本

备

注

项目名称

料号

版本号

设计时间

设计师

包装工程师

比例 1:1 单位 mm

材质：金东太空梭 105g 哑粉

装订：胶装

成品尺寸：182*130mm

页数：84P

参考色：PANTONE Cool Gray 11 C，

PANTONE 185 C

尺寸偏差：±1.5mm

印刷偏位：±1mm

182mm

130mm

版本号：

修改点：

修改人：

版本号：V2.0 2021.12.27

修改点：内容及线稿图修改，增加小语

修改人：张云鹏

版本号：

修改点：

修改人：

版本号：V3.0 2022.01.03

修改点：校准意见修改

修改人：张云鹏

版本号：

修改点：

修改人：

版本号：

修改点：

修改人：

版本号：

修改点：

修改人：

版本号：

修改点：

修改人：

版本号：

修改点：

修改人：

版本号：

修改点：

修改人：

Tanos_S _lite+OC 组合装说明书（CE 版）

4.03.0532

V3.0

2022.01.03

张云鹏

严德球

石头科技产品包装图纸

Roborock Q7 Max+

Read this user manual with diagrams carefully before using

this product and store it properly for future reference.

Robotic Vacuum Cleaner User Manual

English Contents

03 Safety Information

05 Product Overview

06 Installation

07 Connect to the App

07 Instructions

09 Routine Maintenance

10 Basic Parameters

11 Errors

12 FAQs

English 03

Français 14

Deutsch 24

Italiano 34

Español 44

Polski 54

Norsk 64

Svenska 74

Restrictions

•Use the product according to the manual. Any loss or damage caused from improper use will be borne by the user.

•Do not use this product on elevated surfaces without barriers such as the oor of a loft, an open-ended terrace, or on top of furniture.

•To prevent blocking the product and to avoid damage to valuables, remove lightweight items (such as plastic bags) and fragile objects (such

as vases) from the oor before cleaning.

•Keep the main brush cleaning tools out of reach of children.

•Do not place any object (including children and pets) on the product, whether it is in operation or not.

•Do not use the product on burning objects (such as cigarette butts).

•Do not use the product to clean hard or sharp objects (such as decoration wastes, glass and nails).

•The product must be switched o and the plug must be removed from socket outlet before cleaning or maintaining the product.

•Do not place any object near the suction inlet of the dock.

•Do not put ngers into the seam of the dock to avoid possible injury.

•Do not operate the product in a room where an infant or child is sleeping.

•Do not carry the product using the dustbin handle or lter cover.

•Make sure the robot is compatible with the dock, otherwise emptying or charging may fail.

•Do not use the dock to pick up stones, paper scraps, or other objects that may block the air duct. If the air duct gets blocked, clean it

immediately.

•Place the dock on a at oor away from re, heat, and water. Avoid narrow spaces or locations where the robot may be suspended in air.

•Do not place any object (including children and pets) on the dock or cover it with any item (including dust-proof cover), whether it is in

operation or not.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

•Do not use the dock to pick up ammable or explosive objects such as re lighter, gasoline, and toner used in printers or copiers.

Safety Information English

•For the purposes of recharging the battery, only use the detachable supply unit roborock CDZ11RR, CDZ12RR, AED03HRR or AED04HRR provided with

this product.

•If placing the robot into storage, charge it fully and turn it o before placing it in a cool dry place. Recharge it at least every three months to

prevent the battery over discharging.

•In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external

switching device, such as a timer, or connected to a circuit that is regularly switched on and o by the utility.

•Be sure that the supply voltage meets the requirements listed on the dock.

•Only use the power cable provided with the product to prevent potential smoke, heat or re.

•Do not use the product with any type of power adapter, as this may cause danger and void the warranty.

•If the dock is placed in an area susceptible to thunderstorms or with unstable voltage, take protection measures.

•Unplug the power cable before placing the dock into storage.

Safety Information

Battery and Charging

WARNING

Product Overview

A1 Robot (Top View)

•Press to return to dock

Press any button to stop the robot during cleaning

or docking.

Note:

—Dock

A3 Robot (Upper Cover Open)

A3-1—WiFi Indicator Light

•O: WiFi disabled

•Flashing slowly: Waiting for connection

•Flashing quickly: Connecting

•Steady: WiFi connected

•Press to Spot clean

•Press and hold for 3 seconds to turn

on/o the child lock

—Spot Clean/Child Lock

•Press and hold to turn the robot on or o

•Press to start cleaning

—Power/Clean

•White: Battery level ≥ 20%

•Red: Battery level < 20%

•Pulsing: Charging or starting up

•Flashing red: Error

—Status Indicator Light

A1-1—Bumper

A1-2—LiDAR Sensor

A1-3—Vertical Bumper

A1-4—Dock Locator

A2 Robot (Bottom View)

A2-1—Wall Sensor

A2-2—Cli Sensors

A2-3—Omni-Directional Wheel

A2-4—Charging Contacts

A2-5—Side Brush

A2-6—Main Wheel

A2-7—Main Brush

A2-8—Main Brush Cover Latches

A4 Dustbin and Water Tank

Combo Unit

A4-1—Water Tank Stopper

A4-2—Water Filter

A4-3—Washable Filter

A3-2—System Reset

A3-3—Mop Cloth Mount

A3-4—Air Vent

A5 Dustbin (Disposable Dust

Bag Pre-Installed)

A6 Dustbin Cover

A7 Disposable Dust Bag

A8 Base

A8-1—Air Duct Cover Screws (10)

A8-2—Air Duct Cover

A8-3—Screwdriver

A8-4—Base Fastening Screws (6)

A9 Auto-Empty Dock

A9-1—Dustbin Cover

A9-2—Dustbin

A9-3—Base

A9-4—Status Indicator Light

•Steady white: Standby

•Flashing white: Emptying

•Steady red: Malfunction

•Light o: Charging Robot/Not

Powered On

A11 Power Cable Storage

A11-1—Power Cable Storage Slot

A11-2—Cable Outlet

A11-3—Power Port

A10 Auto-Empty Dock (Cover

Removed)

A10-1—Dust Bag Slot

A10-2—Filter

Power cable can be pulled out at both sides.

Note:

A9-5—Dock Location Beacon

A9-6—Charging Contacts

A9-7—Suction Inlet

A9-8—Electrode Brushes

A12 Mop Cloth Mount

A12-1—Mop Cloth Slot

A12-2—Mop Cloth Mount

A12-3—Mop Cloth Mount Latch

When using the robot for the rst time, follow

it throughout its whole cleaning route and watch for

potential problems. The robot will be able to clean by

itself in future uses.

Note:

A13 Mop Cloth

A14 Screwdriver

A15 Power Cable

A13-1—Mop Cloth

A13-2—Hook and Loop Pads

Installation

B1 Important Information

B1-1—Tidy cables and loose items from

the ground and move any unstable,

fragile, precious, or dangerous

items to prevent personal injury

or property damage due to items

becoming tangled in, struck by, or

knocked over by the robot.

B1-2—When using the robot in a raised

area, always use a secure physical

barrier to prevent accidental falls

that may result in personal injury or

property damage.

B2 Dustbin Assembly

B2-1—Take the screwdriver from its storage

bin at the bottom of the base.

B2-2—Place dock upside down on a soft,

at surface (carpet/towel/cloth) and

attach the base by using the six

screws provided.

Hold the dustbin cover securely when upside

down to prevent damage from falling.

Note:

B2-3—Connect the power cable to the dock,

and keep the excess cable inside the

storage slot.

B2-4—Place the dock on a hard and at oor

(wood/tile/concrete etc.). Keep at least

0.5 m (1.6 ft) of clearance on either

side, 1.5 m (4.9 ft) in front, and 1 m

(3.3 ft) above. Check the location has

good WiFi then turn on.

B2-4-1 More than 0.5m (1.6 ft)

B2-4-2 More than 1.5m (4.9 ft)

B2-4-3 More than 1m (3.3 ft)

B3 Emptying

Auto-emptying will begin when the robot

returns to the dock after cleaning. Press

the button to trigger emptying manually.

Press any button to stop emptying.

Notes:

•The status indicator light turns o automatically when

the robot is charging.

•Do not use without dustbin cover or dust bag.

•Place the dock on a at oor away from re, heat, and

water. Avoid narrow spaces or locations where the

robot may be suspended in the air.

•Placing the dock on a soft surface (carpet/mat) may

cause the dock to tilt over and cause problems

docking and departing.

•Keep the excess power cable inside the storage slot so

that the robot will not get tangled in the cable, and the

dock will not be dragged away or disconnect from the

power supply.

•Keep the dock away from direct sunlight or anything

that may block the dock location beacon; otherwise,

the robot may fail to return to the dock.

•The Auto-Empty Dock recharges and empties. Store

the standard robot dock before use. Failure to do so

may cause issues returning to dock.

•Maintain the dock according to the maintenance

instructions. Do not clean the dock with a wet cloth.

•Avoid frequent manual emptying.

•Images are for illustration purposes only and may not

exactly represent the product.

B4 Mopping

To prevent excessive dirt buildup during rst-time

use, oors should be vacuumed at least three times

before mopping.

Note:

Open the upper cover and take out the unit.

B4-1—Remove the dustbin and water

tank combo unit

Reinstall the unit. It will click in place.

B4-3—Reinstall the dustbin and water

tank combo unit

Wet the mop cloth and wring it until it stops

dripping, then slide it along the mop cloth

slot before sticking it rmly in place.

B4-4—Install the mop cloth

Notes:

•To prevent corrosion or damage, only use the

Roborock branded oor cleaner in the water tank.

•Do not use hot water as this may cause the tank to deform.

•When lling the water tank, tilt tank 30° to avoid

wetting the lter.

Remove the water tank stopper, ll the tank

with water, and close it tightly.

B4-2—Fill the water tank

Slide the mount forwards along the bottom

of robot until it clicks in place.

B4-5—Install the mop cloth mount

Clean the mop cloth after 60 minutes of mopping

to maintain water ow and cleaning quality.

Note:

Open the Roborock App, tap the “Search for

device” button, or open Xiaomi Home app, tap

“+” in the top right corner and add the device

as instructed in the app.

Notes:

•The actual process may vary due to ongoing app

updates. Follow the instructions provided in the app.

•Only 2.4 GHz WiFi is supported.

•If the robot waits more than 1 hour for a connection,

WiFi will be automatically disabled. If you want to

reconnect, reset the WiFi before proceeding.

❸Add device

Option 2: Search for “Xiaomi Home” in the

App Store or Google Play or scan the QR

code to download and install the app.

When the robot returns to the dock after

cleaning, press the latches on both sides,

and slide the mop cloth mount backwards

to remove it.

B4-6—Remove the mop cloth mount

Notes:

•Wash the mop cloth after each use, and regularly

empty the water tank of unused water.

•Remove the mop mount when not mopping.

Connect to the App

Option 1: Search for “Roborock” in the App

Store or Google Play or scan the QR code to

download and install the app.

❶Download App

This robot supports both Roborock and

Xiaomi Home apps. Choose the one that

best meets your needs. ❷Reset WiFi

1. Open the upper cover and nd the WiFi

indicator.

If you cannot connect to the robot due to your

router conguration, a forgotten password, or any other

reason, reset the WiFi and add your robot as a new device.

Note:

2. Press and hold the and buttons until

you hear the “Resetting WiFi” voice alert. The

reset is complete when the WiFi indicator

ashes slowly. The robot will then wait for a

connection.

Only use the ocial Roborock mop cloth.

Note:

Instructions

The robot cannot be turned o when it is being

charged.

Note:

Press and hold the button to turn on the

robot. The power indicator will turn on and

the robot will enter standby mode. Press

and hold the button to turn o the robot

and complete the cleaning cycle.

On/O

Press the button to start cleaning. The

robot will plan its cleaning route according

to its scan of the room. It splits a room into

zones, rst draws out zone edges, and then

lls the zone in a zigzag pattern. In doing

so, the robot cleans all zones one by one,

eciently cleaning the house.

Starting Cleaning

The default Do Not Disturb (DND) period is

from 22:00 to 08:00. You can use the app to

disable the DND mode or modify the DND

period. When DND mode is activated, the

robot will not automatically resume cleanup,

the power indicator light will dim, and the

volume of the voice prompts will lower.

DND Mode

Child Lock

Press and hold the button to enable/

disable the child lock. You can also set it in

the app. Once enabled, the robot will not

react to button presses when it is stationary.

When the robot is cleaning or docking,

press any button to stop it.

After cleaning, the robot will automatically

return to the dock to charge.

Charging

If the robot fails to nd the dock, it will

automatically return to its starting location. Place the

robot on the dock manually to recharge.

Note:

If an error occurs, the power indicator will

ash red and a voice alert will sound. See “

Errors” for solutions.

Error

•The robot will go to sleep automatically if left in a

malfunctioning state for over 10 minutes.

•Placing a malfunctioning robot on the dock manually

will end the current cleanup.

Notes:

If the robot does not function properly after

a system reset, switch it on. Press and hold

the button and at the same time press

Reset button until you hear the “Restoring

factory settings” voice prompt. The robot

will then be restored to factory settings.

Restore Factory Settings

If the robot does not respond when a button

is pressed or cannot be turned o, reset

the system. Press the Reset button, and the

robot will reset automatically.

System Reset

After resetting the system, scheduled cleaning,

WiFi, etc. will be restored to factory settings.

Note:

When the robot is running, press any button

to pause it, press the button to resume

cleaning, press the button to send it back

to the dock.

Pause

Placing a paused robot on the dock manually will

end the current cleanup.

Note:

•The robot will not go to sleep when it is charging.

•The robot will automatically shut down if left in sleep

mode for more than 12 hours.

Notes:

If the robot is paused for over 10 minutes, it

will go to sleep, and the power indicator will

ash every few seconds. Press any button to

wake the robot up.

Sleep

•To allow the robot to automatically vacuum and return

to the dock, start the robot from the dock. Do not

move the dock during cleaning.

•Cleaning cannot start if the battery level is too low.

Allow the robot to charge before starting cleanup.

•If cleaning is completed in less than 10 minutes, the

area will be cleaned twice.

•If the battery runs low during the cleaning cycle,

the robot will automatically return to the dock. After

charging, the robot will resume where it left o.

•Before starting each mopping task, make sure that the

mop cloth has been properly installed.

Notes:

Press the button to start spot cleaning.

Cleaning range: The robot cleans a 1.5 m

(4.9 ft) x 1.5 m (4.9 ft) square area centered

on itself.

Spot Cleaning

After spot cleaning, the robot will automatically

return to the starting point and enter Standby mode.

Note:

Zone 1 – Cleaned

Zone 4 – Next Zone

Zone 2 – Cleaned

Zone 3 – In Progress

In Pause mode, press the button to

send the robot back to the dock. The power

indicator will pulse as the robot charges.

Functions and details of the app may vary slightly

due to the continuous app development and updates.

Note:

Routine Maintenance

C1 Main Brush

* Clean every 2 weeks and replace every 6-12 months

C1-1—Main Brush Cover

C1-2—Latches

C1-3—Main Brush

C1-4—Main Brush Caps

C1-5—Main Brush Bearing

C1-6—Turn over the robot and press the

latches to remove the main brush cover.

C1-8—Rotate the main brush caps in the

indicated unlock direction to remove

the caps.

C1-7—Pull out the main brush and remove

the main brush bearing.

C1-9—Remove any hair or dirt entangled

around the main brush, reinstall the

main brush and re-insert the brush

cover, making sure to place the tabs

in the slots.

C1-10—Make sure that the main brush cover

has been properly attached. When

properly installed, all four tabs should

be hidden.

Notes:

•Main brush should be wiped down with wet cloth and

left to dry away from direct sunlight.

•Do not use corrosive cleaning uids or disinfectants to

clean the main brush.

C2 Side Brush

1. Unscrew the side brush screw.

2. Remove and clean the side brush.Reinstall

the brush and tighten the screw.

* Clean monthly and replace every 3-6 months

C3 Omni-Directional Wheel

C3-1—Use a tool, such as a small screwdriver,

to pry out the axle and take out the

wheel.

* Clean as required

App Features

Cleaning Map

•Multi-Map Management

•Real-Time Vacuum and Mop Route

•Map Zoning

•Map Editing

Custom Cleaning Modes

•Scheduled

•Selective Room

•Zone

•No-Go Zones & Invisible Wall

•Custom

•Carpet Boost

Cleaning Mode Switch

•Suction Power Levels

•Mop Intensity Levels

Robot Information

•Cleaning History

•Battery Level

•Care & Maintenance

More Features

•Firmware Update

•Volume Adjustment

•Language Selection

•Do Not Disturb mode

•Voice Assistant Support

The omni-directional wheel bracket cannot be

removed.

Note:

C3-2—Rinse the wheel and the axle with

water to remove any hair and dirt.

Dry and reattach the wheel, pressing

it rmly in place.

Clean the main wheels with a soft, dry cloth.

C4 Main Wheels * Clean monthly

C5-4—Fill the dustbin with clean water and

gently shake it. Then pour out the

dirty water.

C5-2—Remove the lter then empty the dustbin.

C5-1—Open the upper cover of the robot

and take out the unit.

C5 Dustbin and Water Tank

Combo Unit

* Clean weekly and replace the lter every 6-12 months

C5-3—Empty the water tank of unused water.

To prevent blockage, only use clean water without

any cleaning liquid.

Note: C8-2—Wipe the air duct and cover with a

dry cloth.

C8-3—Reinstall the cover and screw it back

in place.

C8-1—Unscrew the screws (10) and remove

the cover.

C8 Air Duct * Replace as needed

C10 Charging Area Cleaning

Clean the dock location beacon, charging

contacts, and electrode brushes with a dry cloth.

* Clean as needed

Use a soft, dry cloth to wipe and clean all

sensors, including:

C9 Robot Sensors * Clean monthly

C9-1—Dock Locator

C9-2—Wall Sensor

C9-3—Four Cli Sensors

Battery

The robot is equipped with a high-performance

lithium-ion rechargeable battery pack. To

maintain battery performance, keep the robot

charged during normal use.

If the robot will be left unused for a long period,

turn it o and charge it at least every three months to

avoid battery damage caused by over-discharge.

Note:

C5-5—Rinse the lter repeatedly and tap it

to remove as much dirt as possible.

C5-6—Allow 24 hours for the filter to dry

thoroughly and reinstall it.

Do not touch the surface of the lter with your

hands, brush, or hard objects to avoid potential damage.

Note:

Purchase an additional lter and alternate if necessary. Note:

C6 Mop Cloth

* Clean after each use and replace every 3-6 months

Remove the mop cloth from the mop cloth

mount. Clean the mop cloth and air-dry it.

A dirty mop will aect the mopping performance.

Clean it before use.

Note:

C7-2—Lift the dust bag out of the dustbin

and discard it.

C7-4—Install a new dust bag in place along

the slot and put the dustbin cover back.

C7-3—Clean the lter with a dry cloth.

The dust bag handle seals the bag on removal to

prevent dust leakage.

Note:

C7-1—Remove the dustbin cover vertically

as shown.

C7 Dust Bag Replacement

* Replace as needed

Basic Parameters

Robot

Q380RRModel

14.4V/5200mAh

lithium-ion battery

Battery

Approx. 4.7kgWeight

The serial number is on a sticker on the underside

of the robot.

Note:

< 6 hoursCharging Time

20VDC 1.2ARated Input

Auto-Empty Dock

14.4V/5200mAh

lithium-ion battery

Charging Battery

AED03HRR, AED04HRRModel

220-240VACRated Input Voltage

50-60HzRated Frequency

Rated Input

(Dust Collection)

0.5ARated Input (Charge)

20VDC 1.2ARated Output

Errors

If an error occurs while the robot is cleaning, the power indicator

will ash red quickly, and a voice alert will sound. Refer to the

following table for troubleshooting.

1. After resolving any of the following errors, relocate your robot

and restart cleaning.

2. After any sensor errors, clean the sensor and retry.

3. If the battery is at an abnormal temperature, wait for it to return

to normal before use.

Error 1: LiDAR turret or laser blocked. Check for obstruction and

retry.

Error 2: Bumper stuck. Clean it and lightly tap to release it.

Error 3: Wheels suspended. Move robot and restart.

Error 4: Cli sensor error. Clean cli sensors, move robot away

from drops and restart.

Error 5: Main brush jammed. Clean main brush and bearings.

Error 6: Side brush jammed. Remove and clean side brush.

Error 7: Wheels jammed. Move the robot and restart.

Error 8: Robot trapped. Clear obstacles surrounding robot.

Error 9: No dustbin. Install dustbin and lter.

Error 12: Low battery. Recharge and retry.

Error 13: Charging error. Clean charging contacts and retry.

A system reset may resolve some problems.Note:

Error 14: Battery error.

Error 16: Robot tilted. Move to level ground and restart.

Error 17: Side brush error. Reset robot.

Error 18: Fan error. Reset robot.

Error 21: Vertical bumper pressed. Move robot and retry.

Error 22: Dock locator error. Clean and retry .

Error 23: Could not return to dock. Clean dock location beacon

and retry.

Error 26: Wall sensor dirty. Clean wall sensor.

Filter blocked or wet. Clean, dry, and retry.

No-go zone or Invisible Wall detected. Move robot from this area.

Internal error. Reset the robot.

If the problem persists after using the recommendations in the

table above, please email our after-sales service team:

Europe Support: support@roborock-eu.com

Australia Support: service@roborock.com.au

FAQs

Problem

Unable to power on.

•Battery low. Put the robot on the dock and charge it before use.

•Battery temperature too low or too high. Only use the robot within the range of 4-40°C (39.2-104°F).

Unable to charge.

•If the dock is not receiving power, check that both ends of the power cable are properly connected.

•If the contact is poor, clean the charging contacts of the dock and the robot.

•Conrm that the dock indicator is on.

Slow charging speed.

•To maintain the battery life, the robot automatically reduces the charging speed when it is charged in an

environment at a high or low temperature.

•Charging contacts dirty. Clean them with a dry cloth.

Unable to return to dock.

•There are too many obstacles near the dock. Move it to an open area.

•The robot is too far from the dock. Place it closer and retry.

Abnormal behavior.

•Restart the robot.

Noise during cleaning.

•The main brush, side brush, or main wheel may be jammed. Turn o the robot and clean them.

•The omni-directional wheel is jammed. Use a screwdriver to remove it for cleaning.

Poor cleaning performance and/or

leaking dust.

•The dustbin is full and needs emptying.

•The lter is blocked and needs cleaning.

•The main brush is tangled up and needs cleaning.

Solution

Unable to connect to WiFi.

•WiFi disabled. Reset the WiFi and try again.

•Poor WiFi signal. Move the robot to an area with good WiFi reception.

•Abnormal WiFi connection. Reset the WiFi, download the latest mobile app, and retry.

•Current device not supported. Find the supported models in the app.

•Unable to connect to WiFi. There may be an error with your router settings. Contact Roborock Customer

Service for help with troubleshooting.

Scheduled cleaning is not working.

•Battery low. Scheduled cleaning can only begin when the battery level is above 20%.

Is power always being drawn when the

robot is on the dock?

•The robot will draw power while it is docked to maintain battery performance, but the power consumption

is extremely low.

Does the robot need to be charged for at

least 16 hours for the rst three uses?

•No. The lithium battery has no memory eect. The robot can be used any time after it has been fully charged once.

FAQs

Problem Solution

No or little water during washing.

•Check whether there is water in the water tank and check the manual for instructions on how to correctly

install the dustbin and water tank combo unit, mop cloth mount and mop cloth.

Cleaning does not resume after recharging.

•Make sure that the robot is not in DND mode. DND mode will prevent auto top-up.

•If the robot is placed manually on the dock before it is recharged automatically, it will not be able to continue cleanup.

The robot cannot return to the dock after spot

cleaning or when it has been moved manually.

•After spot cleaning or a signicant position change, the robot will re-generate the map. If the dock is too far

away, the robot may not be able to return for recharging and must be placed on the dock manually.

The robot begins to miss certain spots.

•The wall sensor or cli sensors may be dirty. Clean them with a soft, dry cloth.

Red LED indicator on the Auto-Empty Dock.

•The dustbin cover is not in place. Check and correct installation.

•The fan is not operating properly. Potentially due to overheating protection resulting from frequent starting

and stopping. Unplug the power cable and try again after 30 minutes.

•Voltage error. Check that local voltage meets the requirements listed on the dock.

Reduced emptying performance or unusual

noise when emptying.

•The main brush or main brush cover is not properly installed. Check and correct installation.

•The lter, air duct, suction inlet, air inlet, or dustbin is blocked. Clean to remove blockages.

Auto-emptying does not start when the robot

returns to the dock.

•Auto-emptying is disabled. Check in-app settings.

•Dustbin cover is not in place. Check and install.

•Auto-emptying will not be triggered if the robot is moved to the dock manually. Start emptying manually.

•Auto-emptying will not be triggered if the robot returns to the dock without cleaning.

•The robot will not auto-empty after returning to the dock in Do Not Disturb (DND) mode. Adjust cleaning or

DND duration, or start emptying manually.

•The battery level is lower than 10%. Charge the robot until the battery reaches 10%.

The robot cannot return to the dock or cannot

be charged.

•The dock is surrounded by obstacles. Clear any obstacles around it or move it to an open area as

recommended in the User Manual.

•The dock is not connected to a power supply. Make sure the power cable is securely plugged in and power is on.

•Poor contact. Clean charging contacts.

Roborock Q7 Max+

Manuel d’utilisation de l’aspirateur robot

Lisez attentivement ce manuel d’utilisation et ses schémas avant d’utiliser le produit et

rangez-le soigneusement pour référence future.

Contenu

Français

15 Informations de sécurité

17 Présentation du produit

18 Installation

19 Connexion à l’application

20 Instructions

21 Entretien de routine

23 Paramètres de base

23 Erreurs et problèmes courants

Restrictions

Informations de sécurité

•Utilisez le produit conformément aux instructions du manuel. L’utilisateur sera tenu pour responsable de toute perte ou de tout

endommagement résultant d’une utilisation incorrecte.

•N’utilisez pas ce produit sur des surfaces en hauteur sans barrières, par exemple, sur le sol d’une mezzanine, une terrasse ouverte ou le

dessus d’un meuble.

•Pour éviter de bloquer le produit et d’endommager des objets de valeur, retirez les objets légers (tels que des sacs plastique) et les objets

fragiles (tels que des vases) du sol avant le nettoyage.

•Gardez les outils de nettoyage de la brosse principale hors de portée des enfants.

•Ne placez aucun objet et aucune personne (enfants et animaux compris) sur le produit, qu’il soit en fonctionnement ou non.

•N’utilisez pas le produit sur des objets brûlants (tels que des mégots de cigarette).

•N’utilisez pas le produit pour aspirer des objets durs ou tranchants (tels que des débris de décoration, du verre et des clous).

•Avant de nettoyer ou d’entretenir le produit, il doit être éteint et sa che doit être débranchée de la prise électrique.

•Ne placez aucun objet à proximité de l’entrée d’aspiration de la station.

•Ne placez pas vos doigts dans la fente de la station pour éviter toute éventuelle blessure.

•Ne faites pas fonctionner le produit dans une pièce où un nourrisson ou un enfant dort.

•Ne transportez pas le produit à l’aide de la poignée du bac à poussière ou du cache du ltre.

•Assurez-vous que le robot est compatible avec la station, sinon le vidage ou le rechargement risque d’échouer.

•N’utilisez pas la station pour recueillir des cailloux, des morceaux de papier ou d’autres objets qui pourraient obstruer le tuyau d’air. Si le

tuyau d’air est obstrué, nettoyez-le immédiatement.

•Placez la station sur un sol plat à l’écart du feu, de la chaleur et de l’eau. Évitez les espaces ou lieux étroits où le robot risque d’être suspendu

dans l’air.

•Ne placez aucun objet et aucune personne (enfants et animaux compris) sur la station, et ne la recouvrez d’aucun élément (housse anti-

poussière comprise), qu’elle soit en fonctionnement ou non.

•Ne recueillez rien qui brûle ou fume, comme des cigarettes, des allumettes ou des cendres chaudes.

•N’utilisez pas la station pour recueillir des éléments inammables ou explosifs, comme des briquets, de l’essence ou du toner utilisé dans

les imprimantes et photocopieuses.

•N’utilisez que le bloc d’alimentation détachable Roborock CDZ11RR, CDZ12RR, AED03HRR ou AED04HRR fourni avec ce produit pour

recharger la batterie.

•Si vous rangez le robot, rechargez-le complètement et éteignez-le avant de le placer dans un endroit frais et sec. Rechargez-le au moins

tous les trois mois pour éviter que la batterie ne se décharge trop.

•An d’éviter tout risque de remise à zéro involontaire du coupe-circuit thermique, cet appareil ne doit pas être alimenté par un dispositif de

connexion externe, tel qu’un programmateur électrique, ou raccordé à un circuit qui est régulièrement activé et désactivé par le fournisseur

d’électricité.

•Veillez à ce que la tension d’alimentation respecte les exigences mentionnées sur la station.

•Utilisez uniquement le câble d’alimentation fourni avec le produit pour éviter tout risque de fumée, de chaleur ou d’incendie.

•N’utilisez pas le produit avec un adaptateur électrique, quel qu’en soit le type, car cela pourrait entraîner un danger et annuler la garantie.

•Si la station est placée dans une zone susceptible d’être sujette à des orages ou à une tension instable, prenez des mesures de protection.

•Débranchez le câble d’alimentation avant de ranger la station.

Informations de sécurité

Batterie et rechargement

AVERTISSEMENT

Présentation du

produit

Appuyez sur n’importe quel bouton pour

arrêter le robot lorsqu’il nettoie ou revient à la station.

Remarque :

A1 Robot (vue de dessus)

•Appuyez sur ce bouton et maintenez-

le enfoncé pour allumer ou éteindre

le robot

•Appuyez sur ce bouton pour

démarrer un nettoyage

- Marche/Arrêt/Nettoyage

•Blanc : niveau de batterie ≥ 20 %

•Rouge : niveau de batterie < 20 %

•Pulsation : rechargement ou démarrage

•Clignotement rouge : erreur

- Voyant d’état

•Appuyez sur ce bouton pour faire

revenir le robot à sa station

- Station

•Appuyez sur ce bouton pour un

nettoyage localisé

•Appuyez sur ce bouton et maintenez-

le enfoncé pendant 3 secondes pour

activer/désactiver le verrouillage enfant

- Nettoyage localisé/Verrouillage enfant

A1-1 : pare-chocs

A1-2 : capteur LiDAR

A1-3 : pare-chocs vertical

A1-4 : localisateur de station

A2 Robot (vue de dessous)

A2-1 : capteur de murs

A2-2 : capteurs de vide

A2-3 : roulette omnidirectionnelle

A2-4 : contacts de rechargement

A2-5 : brosse latérale

A2-6 : roulette principale

A2-7 : brosse principale

A2-8 : loquets du cache de la brosse principale

A4 Bloc combinant bac à

poussière et réservoir d’eau

A4-1 : bouchon du réservoir d’eau

A4-2 : ltre à eau

A4-3 : ltre lavable

A3 Robot (capot supérieur ouvert)

A3-1 : voyant WiFi

•Éteint : WiFi désactivé

•Lent clignotement : en attente de

connexion

•Clignotement rapide : connexion

•Fixe : WiFi connecté

A3-2 : réinitialisation système

A3-3 : support de serpillière

A3-4 : aération

A5 Bac à poussière (sac à

poussière jetable préinstallé)

A6 Couvercle du bac à poussière

A7 Sac à poussière jetable

A8 Base

A8-1 : vis du cache du tuyau d’air (10)

A8-2 : cache du tuyau d’air

A8-3 : tournevis

A8-4 : vis de xation de la base (6)

A9 Station de vidage automatique

A9-1 : couvercle du bac à poussière

A9-2 : bac à poussière

A9-3 : base

A9-4 : voyant d’état

•Blanc xe : veille

•Blanc clignotant : vidage

•Rouge xe : dysfonctionnement

•Voyant éteint : robot en charge/éteint

A11 Rangement du câble

d’alimentation

A10 Station de vidage

automatique (couvercle retiré)

A10-1 : fente pour le sac à poussière

A10-2 : ltre

A9-5 : balise de localisation de la station

A9-6 : contacts de rechargement

A9-7 : entrée d’aspiration

A9-8 : brosses de nettoyage des électrodes

A11-1 : fente de rangement du câble

d’alimentation

Il est possible de tirer sur le câble

d’alimentation pour le faire sortir des deux côtés.

Remarque :

A12 Support de serpillière

A12-1 : fente pour serpillière

A12-2 : support de serpillière

A12-3 : loquet du support de serpillière

Lorsque vous utilisez votre robot pour

la première fois, suivez-le attentivement tout au long

de son parcours de nettoyage en prenant garde aux

problèmes potentiels. Le robot pourra nettoyer seul lors

des prochaines utilisations.

Remarque :

A13 Serpillière

A14 Tournevis

A15 Câble d’alimentation

A13-1 : serpillière

A13-2 : blocs auto-agrippants

Installation

B1 Informations importantes

B1-1 : rangez les câbles et objets détachés

présents au sol et déplacez tout

objet instable, fragile, précieux ou

dangereux an d’éviter toute blessure

et tout dommage matériel dus à des

objets qui seraient happés, heurtés

ou renversés par le robot.

B1-2 : lorsque vous employez ce robot dans

une zone surélevée, utilisez toujours

une barrière de sécurité physique pour

B2 Assemblage du bac à poussière

B2-1 : sortez le tournevis de son

compartiment de rangement qui se

trouve en dessous de la base.

B2-2 : retournez la station sur une surface

plane et molle (moquette/serviette/

chion) et xez la base à l’aide des six

vis fournies.

Lorsque vous retournez la station,

maintenez fermement le couvercle du bac à poussière

pour éviter de l’endommager suite à une chute.

Remarque :

B2-3 : connectez le câble d’alimentation à la

station et laissez l’excès de câble dans

la fente de rangement.

B2-4 : placez la station sur un sol dur et plat

(bois/carrelage/béton, etc.). Gardez

un espace d’au moins 0,5 m (1,6 pi)

de chaque côté, de 1,5 m (4,9 pi) à

l’avant et de 1 m (3,3 pi) au-dessus.

Vériez que l’emplacement choisi

dispose d’une bonne connexion WiFi

puis mettez la station sous tension.

B2-4-1 Plus de 0,5 m (1,6 pi)

B2-4-2 Plus de 1,5 m (4,9 pi)

B2-4-3 Plus de 1 m (3,3 pi)

B3 Vidage

Le vidage automatique commencera

lorsque le robot reviendra à la station après

le nettoyage. Appuyez sur le bouton Station

pour déclencher manuellement le vidage.

Appuyez sur n’importe quel bouton pour

arrêter le vidage.

Remarques :

•Le voyant d’état s’éteint automatiquement lorsque le

robot est en charge.

•Ne pas utiliser sans couvercle du bac à poussière ou

sac à poussière.

•Placez la station sur un sol plat à l’écart du feu, de la

chaleur et de l’eau. Évitez les espaces ou lieux étroits

où le robot risque d’être suspendu dans l’air.

•Placer la station sur une surface molle (moquette/

tapis) peut entraîner son inclinaison et des problèmes

de départ et de retour à la station du robot.

•Laissez l’excès de câble d’alimentation dans la fente de

rangement an que le robot ne puisse pas s’enchevêtrer

dans le câble et que la station ne puisse pas être

entraînée à l’écart ou déconnectée de l’alimentation.

•Gardez la station à l’écart de la lumière directe du

soleil et de tout ce qui pourrait bloquer la balise de

localisation de la station, sinon, le robot risque de ne

pas parvenir à y revenir.

•La station de vidage automatique recharge et procède

au vidage. Rangez la station de robot standard

avant utilisation. Ne pas le faire peut entraîner des

problèmes de retour à la station.

•Entretenez la station conformément aux consignes

d’entretien. Ne nettoyez pas la station avec un chion

humide.

•Évitez de déclencher fréquemment le vidage manuellement.

•Les images ne sont fournies qu’à des ns d’illustration

et il est possible qu’elles ne représentant pas

exactement le produit.

A11-2 : sortie du câble

A11-3 : port d’alimentation

empêcher les chutes accidentelles qui

pourraient entraîner des blessures ou

des dommages matériels.

Une fois que le robot est revenu à la station

après le nettoyage, appuyez sur les loquets

qui se trouvent des deux côtés, puis faites

glisser le support de serpillière vers l’arrière

pour le retirer.

B4-6 : retrait du support de serpillière

Faites glisser le support vers l’avant le

long du dessous du robot jusqu’à ce qu’il

s’encliquette en place.

B4-5 : installation du support de serpillière

Nettoyez la serpillière après 60 minutes de

son utilisation par le robot pour préserver le débit d’eau

et la qualité de nettoyage.

Remarque :

Ouvrez l’application Roborock et appuyez

sur le bouton « Rechercher un appareil »,

ou ouvrez l’application Xiaomi Home et

appuyez sur le « + » qui se situe dans le coin

supérieur droit. Ajoutez ensuite l’appareil en

suivant les instructions de l’application.

❸Ajout d’un appareil

Option 2 : recherchez « Xiaomi Home » sur l’App

Store ou sur Google Play ou scannez le code QR

pour télécharger et installer l’application.

Remarques :

•Lavez la serpillière après chaque utilisation, et évacuez

régulièrement l’eau inutilisée du réservoir d’eau.

•Retirez le support de serpillière lorsque vous n’utilisez

pas cette fonction.

Connexion à l’application

Option 1 : recherchez « Roborock » sur l’App

Store ou sur Google Play ou scannez le code

QR pour télécharger et installer l’application.

❶Téléchargement de l’application

Ce robot prend à la fois en charge les

applications Roborock et Xiaomi Home.

Choisissez celle qui correspond le mieux à

vos besoins.

❷Réinitialisation du WiFi

1. Ouvrez le capot supérieur et recherchez

le voyant WiFi.

Si vous ne parvenez pas à vous connecter au

robot en raison de la conguration de votre routeur, d’un

mot de passe oublié ou de toute autre raison, réinitialisez

le WiFi et ajoutez le robot comme nouvel appareil.

Remarque :

2. Appuyez sur les boutons et et

maintenez-les enfoncés jusqu’à ce que vous

entendiez l’alerte vocale « Réinitialisation

du WiFi ». La réinitialisation est terminée

lorsque le voyant WiFi clignote lentement.

Le robot sera alors en attente de connexion.

N’utilisez que la serpillière Roborock ocielle.

Remarque :

B4 Nettoyage à la serpillière

Pour éviter toute accumulation excessive

de saleté lors d’une première utilisation, les sols

devraient être aspirés au moins trois fois avant de les

nettoyer à la serpillière.

Remarque :

Ouvrez le capot supérieur et sortez le bloc.

B4-1 : retrait du bloc combinant bac à

poussière et réservoir d’eau

Réinstallez le bloc. Il s’encliquettera en place.

B4-3 : réinstallation du bloc combinant

bac à poussière et réservoir d’eau

Mouillez la serpillière et tordez-la jusqu’à ce

qu’elle cesse de goutter, puis faites-la glisser

le long de la fente pour serpillière avant de

la faire fermement adhérer en place.

B4-4 : installation de la serpillière

Remarques :

•Pour éviter toute corrosion ou tout dommage,

n’utilisez que du nettoyant pour sols de marque

Roborock dans le réservoir d’eau.

•N’utilisez pas d’eau chaude car cela peut entraîner une

déformation du réservoir.

•Lorsque vous remplissez le réservoir d’eau, inclinez-le

à 30° pour éviter de mouiller le ltre.

Retirez le bouchon du réservoir d’eau,

remplissez-le d’eau, puis refermez-le fermement.

B4-2 : remplissage du réservoir d’eau

La pagina sta caricando ...

Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Manuale utente

Marca: Roborock

Modello: Q7 MAX+ ROBOTSTØVSUGER, SVART

Categoria: Aspirapolvere robotici

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

français: Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Manuel utilisateur
español: Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Manual de usuario
Deutsch: Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Benutzerhandbuch
dansk: Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Brugermanual
polski: Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Instrukcja obsługi
svenska: Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Användarmanual

Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Manuale utente

Roborock Q7 MAX+ ROBOTSTØVSUGER, SVART Manuale utente

in altre lingue

Documenti correlati

Altri documenti