Follett chewblet 7FS100A Installation, Operation And Service Manual

Order parts online:

www.follettice.com

01156496R01

801 Church Lane • Easton, PA 18040, USA

Toll free (877) 612-5086 • +1 (610) 252-7301

www.follettice.com

Installation, Operation and Service Manual

Ice and Sparkling Water Dispenser

with Chewblet

®

Ice Icemaker

7CI100A, 7FS100A, 15CI100A, 15FS100A

Following installation, please forward this manual

to the appropriate operations person.

7FS100A

7CI100A

15FS100A

15CI100A

2 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Follett 7/15 Series Sparkling - Installation Checklist

Before beginning:

 Separate boxes for dispenser, carbonator, installation kit, and accessories.

 Customer-supplied, beverage-grade CO2 cylinder is present and full.

Assemble system:

 Sparkling Water, Still Water, and power cord installed between carbonator and

dispenser.

 Water Block ood protection device set to “2” and installed vertically after tee on the

water line to the carbonator water inlet.

 ShockBlok water pressure regulator installed after Water Block and before

carbonator water inlet.

 CO2 regulator set to 60 psi.

Turn on water, plug in dispenser – leave carbonator and CO2 off:

 No leaks in plumbing connections. Check before reinstalling dispenser side panel.

 Carbonator air is bled according to installation instructions.

Turn on carbonator and CO2:

 Sparkling and Still Water ow from correct button press.

 Carbonator pump cycles on and off between Sparkling Water dispenses.

 Perform 4 separate 16 oz. Sparkling Water dispenses.

Notes: Allow carbonator pump to cycle off between dispenses.

Do not exceed 32 oz. continuous sparkling dispense.

Allow at least 1 hour for chiller to reach optimal temperature.



Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 3

Contents

About Follett Sparkling Water .................................................................... 4

Welcome ...................................................................................... 4

Before You Begin ............................................................................... 5

Important Safety Information ..................................................................... 6

Specications ................................................................................. 6

Dispenser Dimensions ........................................................................ 6

Carbonator Dimensions ....................................................................... 6

Ambient Information .......................................................................... 6

Plumbing ................................................................................... 6

Specications ................................................................................. 7

Water ..................................................................................... 7

Clearances ................................................................................. 7

Electrical ................................................................................... 7

Refrigeration ................................................................................ 7

Heat Rejection .............................................................................. 7

Chiller/Carbonator Detailed Drawing ............................................................. 7

7 Series Detailed Drawing ..................................................................... 8

15 Series Detailed Drawing .................................................................... 9

Installation ....................................................................................10

Countertop Installation ........................................................................10

Freestanding Installation ...................................................................... 12

Final Connections - Countertop Installation ...................................................... 14

Final Connections - Freestanding Installation ..................................................... 16

Maintenance/Cleaning Mode .................................................................... 19

Accessing Internal Components ................................................................. 19

DIP-switch Settings ............................................................................ 20

NSF-approved Cleaning and Sanitizing Procedure .................................................. 21

User Interface and Exterior Cabinet Cleaning ...................................................... 22

Flow Straightener Cleaning/Sanitizing ............................................................ 22

Chiller/Carbonator Sanitizing Instructions ......................................................... 22

Service ...................................................................................... 23

LED Indicator Description ..................................................................... 23

Evaporator Disassembly ...................................................................... 24

Evaporator Assembly ........................................................................ 27

Condenser Fan Motor Removal (7 Series Shown) ................................................. 31

Bin Melt Water/Evaporator Feed/Clean Out System Schematic ....................................... 32

Vent System Schematic ...................................................................... 32

Refrigeration Schematic - Dispenser ............................................................ 33

Water Feed Schematic ....................................................................... 34

Chiller/Carbonator ........................................................................... 35

User Interface Display Identication ............................................................. 36

Electrical Wiring Diagram - Dispenser ........................................................... 38

Electrical Wiring Diagram - Chiller/Carbonator ..................................................... 39

Parts ........................................................................................ 40

7 Series Exterior ............................................................................ 40

7 Series Interior ............................................................................ 42

15 Series Exterior ........................................................................... 44

15 Series Interior ........................................................................... 46

7 Series Bin Assembly ....................................................................... 48

15 Series Bin Assembly ...................................................................... 50

Evaporator Assembly ........................................................................ 52

Base Stand ................................................................................ 54

Chiller/Carbonator ........................................................................... 55

4 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

About Follett Sparkling Water ––––––––––––––––––––––––––––––––––––––––

Follett’s 7 and 15 Series Ice and Sparkling Water dispensers produce Follett’s consumer-preferred Chewblet

®

nugget ice as well as chilled and sparkling water. Follett’s premium sparkling drinking water is characterized by

small, dense bubbles. Follett does not produce the large “popping” bubbles found in sugary soda drinks. A good

comparison for Follett’s sparkling water would be Perrier or Pellegrino. It is important to note this distinction.

Customers who are seeking the big-bubbles found in club soda or soft drinks may be disappointed. However, taste

tests conducted by Follett at a variety of test sites have veried a high level of approval for Follett’s sparkling water.

Two factors play a large part in producing quality sparkling water. First, the water being injected with food grade

CO2 must be controlled between 46 F – 51 F. Second, the incoming water must have the proper range of mineral

content. Too many minerals can lead to premature scaling of the ice maker and the need for excess product

maintenance. Too few minerals can result in avorless sparkling water which can go at quickly. To ensure the

highest quality sparkling water, the water supply (after ltration) must have a hardness between 80 ppm and

400ppm TDS. Test your water rst and lter as necessary to achieve the appropriate hardness. Filtration should

also remove any chlorine tastes from the water, another enemy of good sparkling water taste.

An appropriate source of CO2 must be in place prior to installation of this ice and water dispenser. It is critical that

the Follett sparkling system be fed only food grade CO2. Follett does not sell or distribute CO2. Follett provides

a regulator for standard UN1013 beverage grade CO2 tanks with a CGA-320 thread. The CO2 tanks and CO2

itself must be sourced locally by the end user. Tanks must be secured at all times to prevent from tipping, and

must be stored below 120°F. There are a variety of local codes and restrictions about the handling and storage of

CO2 across the U.S. Please consult a local CO2 distributor for more information. Follett can provide some limited

guidance to help nd an appropriate source for CO2, however, Follett does not guarantee the ability to provide a

CO2 contact in every market.

Welcome ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability, and outstanding

after-the-sale support. To ensure that this product delivers that same degree of service, we ask that you take a

moment to review this manual before beginning the installation. Should you have any questions or require technical

help at any point, please call our technical service group at (877) 612-5086 or +1 (610) 252-7301.

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 5

Before You Begin –––––––––––––––––––––––––––––––––––––––––––––––––––

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage

is found, immediately notify the shipper and contact Follett Corporation so that we can help in the ling of a claim,

if necessary. If needed, the serial number of your dispenser can be found by removing the drip tray ❶ and locating

the serial number label ❷. A QR Code is located on the right hand side of the drip tray ❸. This code allows you to

access manuals, technical bulletins, and on-line training related to the 7 Series and 15 Series dispensers.

2

1

Scan to access technical

documentation or visit

www.follettice.com/7and15seriesdocs

00981100R01

3

Check your paperwork to verify that you received the correct dispenser. Follett conguration numbers are designed

to provide information about the type of dispenser you are receiving. The following is an explanation of the different

model numbers.

7 CI 100 A

Dispenser Storage

Capacity

Conguration Icemaker Capacity Condenser

7 lb (3.1 kg)

15 lb (6.8 kg)

CI Countertop

FS Freestanding

100 lbs (45.3 kg) per day A Air-cooled

Carbonator Installation Kit Contents

Please conrm the contents of your Carbonator Installation kit:

1 – CO2 regulator 1 – Water Block kit includes:

1 – Water Block ood prevention device

1 – Water Block mounting bracket

2 – ¼" tube x ¾" GHT ttings

1 – ¾" GHT x ¾" GHT tting

1 – 8-32 self tapping screw

15 ft – ¼" OD tubing

1 – Carbonator cradle bracket

1 – Carbonator power cord

1 – ¼" sparkling water tube assembly

1 – 3/8" chilled still water tube assembly

2 – Carbonator front brackets

1 – ¼" plug tting

1 – ¼" tee tting

8" rubber edging

1 – ShokBlok water pressure regulator

5 – 10-32 self tapping screws

6 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Important Safety Information –––––––––––––––––––––––––––––––––––––––––

Please read and adhere to the following safety information while installing, using, or servicing your Follett Ice

Dispenser.

1. Always disconnect power before servicing the dispenser.

2. Ice is slippery. Maintain counters and oors around dispenser in a clean and ice-free condition.

3. Ice is food. Follow the recommended cleaning and sanitizing instructions to maintain cleanliness of

delivered ice.

Specications –––––––––––––––––––––––––––––––––––––––––––––––––––––

Dispenser Dimensions

7CI100A 7FS100A 15CI100A 15FS100A

Width 14.50" (40 cm) 14.50" (36.8 cm) 14.50" (40 cm) 14.50" (40 cm)

Depth 22.12" (56.2 cm) 22.12" (56.2 cm) 23.50" (59.7 cm) 23.50" (59.7 cm)

Height 17.50" (44.5 cm) 41.88" (106.4 cm) 22.50" (57.2 cm) 46.75" (118.7 cm)

Unit Shipping Weight 90 lb (41 kg) 120 lb (54.4 kg) 100 lb (45.4 kg) 130 lb (60 kg)

Carbonator Dimensions

Width 10.25" (26.01 cm)

Depth 16.38" (41.6 cm)

Height 16.38" (41.6 cm)

Unit Shipping Weight 58.5 (26.5 kg)

Ambient Information

CAUTION!

The 7CI100A/7FS100A and 15CI100A/15FS100A are for indoor use only.

Designed for commercial use. Follett is not able to provide in-house services

for residential installations.

Maximum* Minimum*

Air Temperature

†

100 F (38 C) 50 F (10 C)

Water Temperature 90 F (32.2 C) 40 F (4.5 C)

Water Pressure 70 psi (483 kpa) 10 psi (69 kpa)

Relative Humidity 55% at 78 F (25.5 C)

* Use outside of these limitations is misuse and will void warranty.

† Best performance is achieved between 80 F (27 C) and 50 F (10 C).

Plumbing

§ Water Inlet: 1/4" OD push-to-connect

§ Optional Drain Accessory Kit (item# 00956375 or 00981977): 1/2" ID tubing

§ Water shut-off recommended within 5 ft. (1.5 m) of dispenser

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 7

Specications –––––––––––––––––––––––––––––––––––––––––––––––––––––

Water

WARNING!

Connect to potable water supply only.

§ Water Mineral Content:

– TDS: greater than 80 ppm (mg/l) but less than 400 ppm (mg/l)

– Hardness: Less than 200 mg/l (12 gpg)

§ Not recommended for use with softened water

Clearances

§ 3" (77 mm) behind and on each side of dispenser for electrical and connection and ventilation

§ 4" (101.6 mm) around chiller/carbonator

Electrical

§ 115V, 60 Hz, 1 phase, 6.5A, maximum fuse 15A

§ Connect to dedicated 15A circuit, fuse or breaker

§ Must be grounded - requires 3-prong outlet. Do not remove ground.

Refrigeration

WARNING!

Do not damage the refrigerant circuit. Refrigerant can cause personal injury and/or damage dispenser.

Refrigerant R134a

§ Dispenser: 7.6 ounces (215 grams)

§ Chiller/Carbonator: 1.94 ounces (55 grams)

Heat Rejection

§ 1700 BTU/hr (498 W) - dispenser

§ 450 BTU/hr (132 W) - chiller/carbonator

Chiller/Carbonator Detailed Drawing

ALL CARFBONATOR CONNECTIONS ARE 1/4" PUSH TO CONNECT

16.38"

(41.6 cm)

7.69"

(19.5 cm)

10.00"

(25.4 cm)

1.75" (4.4 cm)

10.25"

(26 cm)

POWER

SWITCH

IEC

POWER CORD

CONNECTION

15.06"

(38.3 cm)

3.31"

(8.4 cm)

4.50"

(11.4 cm)

2.19" (5.6 cm)

4.50"

(11.4 cm)

SPARKLING

WATER OUT

1/4” PUSH-

TO-CONNECT

1.75" (4.4 cm)

STILL

WATER OUT

1/4” PUSH-

TO-CONNECT

WATER

INLET

1/4” PUSH-

TO-CONNECT

CO2 GAS

1/4” PUSH-

TO-CONNECT

T-STAT

8 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Specications (continued) ––––––––––––––––––––––––––––––––––––––––––––––

7 Series Detailed Drawing

Freestanding models

Countertop models

17.50"

(44.5 cm)

G

L2

L1

NEMA 5-15

right angle

17.50"

(44.5 cm)

14.50" (36.8 cm)

22.12" (56.2 cm)

24.38"

(61.9 cm)

11.56" (29.4)

12.75" (32.3 cm)

3.94"

(10.0 cm)

10.81"

(27.5 cm)

2.94" (7.5 cm)

2.38" (6 cm)

10.75"

(27.3 cm)

2.19" (5.6 cm)

4.50" (11.4 cm)

15.38"

(39.1 cm)

13.75"

(34.9 cm)

12.25"

(31.1 cm)

0.69" (17.5 mm)

CHILLER/CARBONATOR

POWER CORD CONNECTION

SPARKLING WATER INLET

1/4" PUSH TO CONNECT

STILL WATER INLET 3/8"

PUSH TO CONNECT

WATER INLET 1/4"

PUSH TO CONNECT

CO2 INLET 1/4" PUSH

TO CONNECT

G

L2

L1

NEMA 5-15

right angle

10.81"

(27.5 cm)

2.94" (7.5 cm)

2.38" (6 cm)

10.75"

(27.3 cm)

15.38"

(39.1 cm)

13.75"

(34.9 cm)

12.25"

(31.1 cm)

0.69" (17.5 mm)

CHILLER/CARBONATOR

POWER CORD CONNECTION

SPARKLING WATER INLET

1/4" PUSH TO CONNECT

STILL WATER INLET 3/8"

PUSH TO CONNECT

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 9

Specications (continued) ––––––––––––––––––––––––––––––––––––––––––––––

15 Series Detailed Drawing

Freestanding models

Countertop models

22.50"

(57.2 cm)

14.50" (36.8 cm)

22.12" (56.2 cm)

22.38"

(56.8 cm)

24.38"

(61.9 cm)

G

L2

L1

NEMA 5-15

right angle

23.50" (59.7 cm)

46.75"

(118.7 cm)

23.50" (59.7 cm)

CHILLER/CARBONATOR

POWER CORD CONNECTION

SPARKLING WATER INLET

1/4" PUSH TO CONNECT

STILL WATER INLET 3/8"

PUSH TO CONNECT

G

L2

L1

NEMA 5-15

right angle

11.56" (29.4)

12.75" (32.3 cm)

3.94"

(10.0 cm)

2.19" (5.6 cm)

4.50" (11.4 cm)

WATER INLET 1/4"

PUSH TO CONNECT

CO2 INLET 1/4" PUSH

TO CONNECT

2.94" (7.5 cm)

2.38" (6 cm)

0.69" (17.5 mm)

15.63"

(39.2 cm)

20.25"

(51.4 cm)

18.63"

(47.3 cm)

17.53"

(43.5 cm)

15.69"

(39.9 cm)

CHILLER/CARBONATOR

POWER CORD CONNECTION

SPARKLING WATER INLET

1/4" PUSH TO CONNECT

STILL WATER INLET 3/8"

PUSH TO CONNECT

2.94" (7.5 cm)

2.38" (6 cm)

0.69" (17.5 mm)

15.63"

(39.2 cm)

20.25"

(51.4 cm)

18.63"

(47.3 cm)

17.53"

(43.5 cm)

15.69"

(39.9 cm)

10 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Installation ––––––––––––––––––––––––––––––––––––––––––––––––––––––––

CAUTION!

No service or maintenance should be performed until the technician

has thoroughly read this service manual. Except for routine cleaning

and sanitizing, only qualied technicians should attempt to service

or maintain this equipment.

Countertop Installation

The 7 Series countertop model is designed to t on counters underneath

standard mounted cabinets, this does not apply to 15 Series models or

any model using optional leg accessory. See page 6 for dimensions.

Installation instructions for freestanding model may be found on page 12.

1. A clearance of at least 3" (77 mm) is required behind and on

each side of the dispenser for electrical connection and ventilation

(Fig.1).

2. Position dispenser in desired nal location and trace opening for

countertop cutout (right-side panel must be removed) or use Fig. 2

to locate cutout.

3. Use appropriate tool to make cutout.

Fig. 1

countertop models

minimum 3" (77 mm)

clearance required

Fig. 2

8.28" (21 cm)

1.76" (4.5 cm)

1.81"

(4.6 cm)

3" (7.6 cm)

REQUIRED CLEARANCE

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 11

4. Position chiller/carbonator in cabinet (allow for required clearances, 4" on sides and back) and mark for

toe-kick recess cutout (Fig. 3).

5. Use appropriate tool to make toe-kick recess cutout.

6. Rough-in the electrical service and water line(s).

§ Electrical: 115V, single phase, 15A receptacle required. The dispenser has an integral 8 ft. (2.4 m) cord and

plug. The chiller/carbonator connects to the dispenser via a supplied 6 ft. power cord.

§ Water: supply line (with shut-off valve) connects to the dispenser's 1/4" NPT male inlet. A tee tting can be

employed to supply both the dispenser and chiller/carbonator from a single shut-off valve. Alternatively, a

second supply line (with shut-off valve) can be installed within the cabinet for the chiller/carbonator's 1/4"

push-to-connect inlet.

NOTICE!

If installing optional Drip Tray Drain Kit or Leg Accessory, complete those steps before proceeding.

Refer to instructions included with the Drip Tray Drain Kit, or see page 12 for Leg Accessory

instructions.

Fig. 3

VENTILATION CUTOUT TO BE

PLACED OVER KICK RECESS AND

ALIGNED WITH VENT SHROUD

COUNTERTOP

CUTOUT FOR DISPENSER

5.13"

1.47"

7. Place chiller/carbonator unit on oor in front of dispenser.

8. Follow the Final Connections instructions for countertop models that follows.

12 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Installation (continued) –––––––––––––––––––––––––––––––––––––––––––––––––

Optional Leg Accessory Installation

CAUTION!

Use caution when tipping the dispenser during leg installation. Do

not lay unit on back or side. DO NOT EXCEED 30° angle. Tipping

more than 30° can result in compressor malfunction.

1. If installing optional 4" Leg Accessory (item# 00956300), place a 5"

(127 mm) spacer underneath the dispenser to ease installation.

2. Remove four plastic, thread-protecting plugs from bottom of

dispenser.

3. Screw each leg into chassis (Fig. 4).

Fig. 4

Freestanding Installation

Installation instructions for countertop model may be found on Countertop

Installation on page 10.

1. A clearance of at least 3" (77 mm) is required behind and on

each side of the dispenser for electrical connection and ventilation

(Fig.5).

2. Rough-in the electrical service and water line(s).

§ Electrical: 115V, single phase, 15A receptacle required. The dispenser

has an integral 8 ft. (2.4 m) cord and plug. The chiller/carbonator

connects to the dispenser via a supplied power cord.

§ Water: supply line (with shut-off valve) connects to 1/4" push-to-

connect Tee that splits the supply to the dispenser and chiller/

carbonator (also 1/4" push-to-connect).

Fig. 5

spacer

5" (127 mm)

min.

freestanding models

minimum 3" (77 mm)

clearance required

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 13

1. To install 6" Leg Accessory (item# 00956318), tilt or lay base stand

on side and screw each leg into stand (Fig.6).

Fig. 6

2. Remove four plastic, thread-protecting plugs from bottom of

dispenser.

3. Attach dispenser to base stand with supplied hardware (Fig. 7).

NOTICE!

If installing optional Drip Tray Drain Kit, refer to instructions

included with the Drip Tray Drain Kit.

4. Place chiller/carbonator unit on oor in front of dispenser.

5. Follow the Final Connections instructions for countertop models that

follows.

Fig. 7

X4

14 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Final Connections - Countertop Installation

1. Use 1/4" OD tubing to plumb incoming water (above countertop) to the tting on the rear of the dispenser

(Fig. 8.1).

2. Mount the Flood Prevention Valve bracket inside the cabinet. Refer to the instructions included with the

Flood Prevention Valve and set the Valve to the "2" position using the included key.

3. Use 1/4" OD tubing to plumb incoming water (below countertop) to the Flood Prevention Valve, assuring

the correct length so that it snaps into the mounting bracket (note proper ow direction) (Fig. 8.2).

4. Plumb to the Water Pressure Regulator (Fig. 8.3).

5. Then plumb to the Chiller/Carbonator (Fig. 8.4) assuring there is enough line that the Chiller/Carbonator

can be removed and set in front of the cabinet. Note proper ow direction for the devices and the Flood

Prevention Valve must be mounted vertically.

6. Remove the right side panel of the dispenser (see Page 24) to expose the Chiller/Carbonator connections.

7. Install the insulated Sparkling and Chilled Still water lines and the power cord to the dispenser, routing the

lines down through the cutout in the countertop (Fig. 8.5).

Note: Water lines are supplied at 6 ft. lengths. Note the Chilled Still water is 3/8" OD tubing and the Sparkling

water is 1/4" OD tubing.

8. Install the plug in the center Ambient Water Out of the Chiller/Carbonator (Fig. 8.6).

9. Connect the Chilled Still water 3/8" OD tubing to the Chiller/Carbonator (Fig. 8.7).

10. Connect the Sparkling water 1/4" OD tubing to the Chiller/Carbonator (Fig. 8.8).

11. Install the tube tting and are washer onto the CO2 regulator. Install the CO2 pressure regulator onto

the CO2 tank. Make sure that the CO2 tank is installed in a location with appropriate tipping prevention

according to local codes. Installing an OSHA approved cylinder rack with chain in an adjacent cabinet with

easy access for cylinder change-outs is recommended.

12. Install 1/4" OD LLDPE tubing from the regulator to the back of the Chiller/Carbonator (Fig. 8.9).

13. Leave the shutoff valve in the OFF position and open the cylinder valve. Using a at blade screwdriver

adjust the CO2 pressure to 60 psi on the top gauge. (The CO2 cylinder is not supplied and is the

responsibility of the customer.)

14. Turn on water and leave CO2 off. Make sure all water valves are open and check for leaks.

15. Plug in the dispenser but do not turn Chiller/Carbonator on at this point.

16. Dispense 1 liter Still water from the dispenser, then dispense 1 liter Sparkling water (Note: at this point,

the water will not be carbonated).

1 7. Remove the screw from the Chiller/Carbonator top panel (Fig. 8.10) and remove top panel (Fig. 8.11).

18. Pull the Chiller/Carbonator safety valve ring (Fig. 8.12) until water starts to come out of the side of the

tting and release immediately. It may take up to a minute for water to run from the safety valve. Reinstall

Chiller/Carbonator top panel.

Note: This procedure is required to remove an air bubble upon initial installation which can prevent the machine

from functioning properly. If air is trapped, the carbonation pump will continue running and eventually fault.

This requires a power cycle to reset.

19. Open the CO2 valve on the CO2 regulator and turn ON the power switch on the front of the Chiller/

Carbonator. Make sure the thermostat on the front of the Chiller/Carbonator is set to the coldest position

(7). Dispense Sparkling water until you hear the Chiller/Carbonator pump turn on (Note: the pump is very

quiet). The pump should turn off again within a few seconds depending on how much carbonated water

is dispensed. Perform at least 3 dispenses to cycle the pump and assure there is no trapped air in the

system.

20. Install Chiller/Carbonator cradle into cabinet. Slide Chiller/Carbonator into cabinet between the cradle

opening and assure the Chiller/Carbonator exhaust shroud is located above the cutout in the toe-kick

recess. Allow 2-4 hours for the Chiller/Carbonator to reach temperature.

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 15

Fig. 8

INCOMING

WATER (above counter,

for ice production)

CO2 REGULATOR

CO2

TANK

WATER

PRESSURE

REGULATOR

IN H2O

IN CO2

FLOOD

PREVENTION

VALVE*

INCOMING

WATER (below counter,

for chilled and sparkling

water)

1

5

4

9

5

2

3

10

11

12

SPARKLING

OUT

AMBIENT CHILLED

OUT

7

6

8

* Flood Prevention Valve must be set to “2” and

mounted vertically - see instructions included

with Valve.

Sparkling water draining procedure

1. Turn off carbonator power and incoming water.

2. Dispense all Sparkling Water until only CO2 comes out (approx. 32 oz.)

3. Turn off CO2 and dispense from Sparkling button to evacuate remaining CO2.

4. Disconnect water, CO2 and power from carbonator.

16 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Final Connections - Freestanding Installation

1. Mount the Flood Prevention Valve bracket to the rear of the base stand (Fig.9.1).

2. Refer to the instructions included with the Flood Prevention Valve and set the Valve to the "2" position

using the included key.

3. Use 1/4" OD tubing to plumb incoming water to the tee tting (Fig. 9.2).

4. Use 1/4" OD tubing to plumb from the tee tting to the tting on the rear of the dispenser (Fig. 9.3).

5. Use 1/4" OD tubing to plumb from the tee to the Flood Prevention Valve, assuring the correct length so

that it snaps into the mounting bracket (note proper ow direction) (Fig. 9.4).

6. Use 1/4" OD tubing to plumb to the Water Pressure Regulator (Fig. 9.5).

7. Then plumb to the Chiller/Carbonator (Fig. 9.6) assuring there is enough line that the Chiller/Carbonator

can be removed and set in front of the base stand.

8. Remove the right side panel of the dispenser (see Page 24) to expose the Chiller/Carbonator connections.

Cut a 1.25" length of the rubber edging. Install the 1.25" length on the short edge of the base stand pass

through (Fig.9.7) and the remaining 6.75" length on the long edge (Fig. 9.8).

9. Install the insulated Sparkling and Chilled Still water lines and the power cord to the dispenser, routing the

lines down through the base stand (Fig. 9.9).

Note: Water lines are supplied at 6 ft. lengths, but can be trimmed to 4 ft. length for freestanding applications. Note

the Chilled Still water is 3/8" OD tubing and the Sparkling water is 1/4" OD tubing.

10. Install the plug in the center Ambient Water Out of the Chiller/Carbonator (Fig. 9.10).

11. Connect the Chilled Still water 3/8" OD tubing to the Chiller/Carbonator (Fig. 9.11).

12. Connect the Sparkling water 1/4" OD tubing to the Chiller/Carbonator (Fig. 9.12).

13. Install the tube tting and are washer onto the CO2 regulator. Install the CO2 pressure regulator onto

the CO2 tank. Make sure that the CO2 tank is installed in a location with appropriate tipping prevention

according to local codes. Installing an OSHA approved cylinder rack with chain in an adjacent cabinet with

easy access for cylinder change-outs is recommended.

14. Install 1/4" OD LLDPE tubing from the regulator to the back of the Chiller/Carbonator (Fig. 9.13).

15. Leave the shutoff valve in the OFF position and open the cylinder valve. Using a at blade screwdriver

adjust the CO2 pressure to 60 psi on the top gauge. (The CO2 cylinder is not supplied and is the

responsibility of the customer.)

16. Turn on water and leave CO2 off. Make sure all water valves are open and check for leaks.

1 7. Plug in the dispenser but do not turn Chiller/Carbonator on at this point.

18. Dispense 1 liter Still water from the dispenser, then dispense 1 liter Sparkling water (Note: at this point,

the water will not be carbonated).

19. Remove the screw from the Chiller/Carbonator top panel (Fig. 9.14) and remove top panel (Fig. 9.15).

20. Pull the Chiller/Carbonator safety valve ring (Fig. 9.16) until water starts to come out of the side of the

tting and release immediately. It may take up to a minute for water to run from the safety valve. Reinstall

Chiller/Carbonator top panel.

Note: This procedure is required to remove an air bubble upon initial installation which can prevent the machine

from functioning properly. If air is trapped, the carbonation pump will continue running and eventually fault.

This requires a power cycle to reset.

2 1. Open the CO2 valve on the CO2 regulator and turn ON the power switch on the front of the Chiller/

Carbonator. Make sure the thermostat on the front of the Chiller/Carbonator is set to the coldest position

(7). Dispense Sparkling water until you hear the Chiller/Carbonator pump turn on (Note: the pump is very

quiet). The pump should turn off again within a few seconds depending on how much carbonated water

is dispensed. Perform at least 3 dispenses to cycle the pump and assure there is no trapped air in the

system.

22. Install Chiller/Carbonator cradle into base stand. Slide Chiller/Carbonator into base stand between the

cradle opening and assure the Chiller/Carbonator exhaust shroud is located above the cutout in the base

stand. Install the front Chiller/Carbonator retaining brackets into the base stand and replace the base

stand cover. Allow 2-4 hours for the Chiller/Carbonator to reach temperature.

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 17

Fig. 9

INCOMING

WATER

CO2 REGULATOR

CO2

TANK

WATER

PRESSURE

REGULATOR

IN H2O

IN CO2

FLOOD

PREVENTION

VALVE*

6

3

9

2

4

5

8

7

13

14

15

16

SPARKLING

OUT

AMBIENT CHILLED

OUT

11

10

12

* Flood Prevention Valve must be set to “2” and

mounted vertically - see instructions included

with Valve.

1

1.25" length

6.75" length

Sparkling water draining procedure

1. Turn off carbonator power and incoming water.

2. Dispense all Sparkling Water until only CO2 comes out (approx. 32 oz.)

3. Turn off CO2 and dispense from Sparkling button to evacuate remaining CO2.

4. Disconnect water, CO2 and power from carbonator.

18 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

Installation (continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

5. Secure unit to wall or cove molding with supplied bracket (Fig. 10) to

prevent tipping.

Note: Fasteners must be supplied by installer.

WARNING!

Freestanding unit must be secured to wall to prevent tipping.

Failure to do could result in personal injury or damage to the

unit.

Fig. 10

Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A 19

Maintenance/Cleaning Mode –––––––––––––––––––––––––––––––––––––––––

Cleaning Mode (Dispensing Disabled) - Use when cleaning surface

Entering Cleaning Mode disables the User Interface and allows you to clean

the outside of the dispenser without accidentally dispensing.

1. To enter Cleaning Mode, press and immediately release the

maintenance/clean switch (Fig. 11.1) so that only "FRESH

FILTERED ICE AND WATER" displays in the user interface

(Fig.11.2).

2. To exit Cleaning Mode, press and immediately release the

maintenance/clean switch so that the ice and water icons also

display in the user interface.

Maintenance Mode (All Operations Disabled) - Use when cleaning ice

machine

Entering Maintenance Mode disables all operations and allows you to safely

clean and/or sanitize the icemaker and dispenser.

1. To enter Maintenance Mode, press and hold the maintenance/

clean switch (Fig. 11.3) until displays in the user interface

(Fig.11.4).

2. To exit Maintenance Mode, press and hold the maintenance/clean

switch until

no longer displays in the user interface.

Note: Entering and exiting Maintenance Mode will reset the six-month

periodic maintenance reminder.

Fig. 11

4

3

2

1

Accessing Internal Components ––––––––––––––––––––––––––––––––––––––

CAUTION!

Except for routine cleaning and sanitizing, only qualied

technicians should attempt to service or maintain this equipment.

1. Press and hold the maintenance/clean switch (Fig. 12.1) until

displays in the user interface (Fig. 12.2).

2. Remove (unscrew) chrome ice dispenser chute (Fig. 12.1).

3. Remove the drip tray (Fig. 12.2).

4. Remove the two screws (Fig. 12.3) on the front panel (behind the

drip tray).

5. Remove and set aside the front panel (Fig. 12.4) - do not

disengage the plug on the back of the User Interface or the

tubing at the water dispenser chute (if so equipped).

Fig. 12

1

2

3

4

20 Sparkling Ice and Water Dispenser 7CI100A/7FS100A, 15CI100A/15FS100A

DIP-switch Settings –––––––––––––––––––––––––––––––––––––––––––––––––

The time delay and the six-month maintenance reminder can be set.

1. Remove the front panel as explained in Accessing Internal

Components on page 19 then refer to Fig. 13.

2. Remove top panel (Fig. 13.1).

Note: For 15 Series dispensers, the right side panel must also be

removed.

3. Remove (1) screw and top of control board enclosure (Fig. 13.2).

4. Locate the DIP switches on the dispenser's control board (Fig. 14).

Ice & water

Internal filter supplied or to display "Fresh Filtered"

Sparkling water

30 minute delay

Six-month PM disabled

OFF ON

Not used (OFF position)

Ice only

No internal filter

Not used (OFF position)

15 minute delay

Not used (OFF position)

Six-month PM enabled

1 2 3 4 5 6 7 8

Fig. 13

1

2

Fig. 14

La pagina sta caricando ...

Follett chewblet 7FS100A Installation, Operation And Service Manual

Questo manuale è adatto anche per

Follett chewblet 7FS100A Installation, Operation And Service Manual

in altre lingue

Documenti correlati

Altri documenti