ProLights Full colour and pixel controlled table centre Manuale utente

Marca: ProLights

Modello: Full colour and pixel controlled table centre

Categoria: Stroboscopi

Tipo: Manuale utente

USER MANUAL

MANUALE UTENT

EN - IT

FULL COLOR AND PIXEL CONTROLLED

TABLE CENTER WITH BATTERY

SMARTDISK

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.003-08/17

SMARTDISK

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic setup

3. 3 Recharge

3. 4 Menu structure

3. 5 DMX addressing

3. 6 DMX mode

3. 7 DMX configuration

3. 8 Wireless setting

3. 9 IR setup

3. 10 Display setting

3. 11 Reload default

3. 12 White balance

3. 13 Fixture information

3. 14 Wireless operation

3. 15 DMX channels

4 Maintenance

4. 1 Maintenance and cleaning the unit

SMARTDISK

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• Supply voltage of this product is DC15V; never connect directly to AC100-240V. Leave servicing to

skilled personnel only. Never make any modiﬁcations on the unit not described in this instruction man-

ual, otherwise you will risk an electric shock.

• Connection of the power adapter must be made to a power supply system ﬁtted with eﬃcient earth-

ing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the

supply lines of the units from indirect contact and/or shorting to earth by using appropriately sized

residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electri-

cal installer. Check that the voltage correspond to those for which the unit is designed as given on the

electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places subject to vibrations or bumps;

- in places subject to excessive humidity.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• Install the ﬁxture in a well ventilated place.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product

SMARTDISK

- 1 - INTRODUCTION

1.1 DESCRIPTION

SMARTDISK is an IP rated, wireless battery powered RGBW LED table centre. Designed for both branding

events and adding a controllable element to a table - it adds an extra dimension to any event design.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 39x0.25W RGB + warm white

• CT: 2800~6000K

• Source life expectancy: >30.000 h

OPTICS

• Beam angle: 360° to light up tables and 25° to light up objects on top

COLOUR SYSTEM

• Colour mixing: RGBW/FC

• Macros: several pre-build pixel macros with adjustable speed

DYNAMIC EFFECTS

• FX generator: adjustable foreground/background colour, index, speed, direction

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of colour

BODY

• Body: sturdy policarbonate body

• Body colour: white

CONTROL

• Protocols: W-DMX

• DMX channels: 4 / 8 / 17 / 165channel

• Pixel control: pixel2pixel control

• W-DMX: included, wireless solution receiver

• Display: LCD display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• IR: infrared sensor controlled by remote

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: diﬀerent dimming curves available

• Strobe / shutter: 1 - 30 Hz, electronic

• Operating temperature: -10° ~ +45°

ELECTRICAL

• Power consumption (at 230V): 19.9W

BATTERY

• Battery: 4.4 Ah - 11.1V lithium

SMARTDISK

• Estimated battery life in colour change mode up to: 15h

• Estimated battery life in single colour mode up to: 24h

• Estimated battery life in full-mode up to: 8h

• Re-charge connection: power cable

• Re-charge time: 5h/max

• Battery status: shown on display

PHYSICAL

• Data connection: W-DMX receiver

• IP rating: 54

• Dimensions (WxHxD): 300x40x300mm

• Weight: 1.62kg

Technical drawing

Fig.1

SMARTDISKPACK Technical drawing

Ø300

527

426

271

SMARTDISK

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

1. Display OLED with display and 4 button used to access the control panel functions and manage them.

2. Side LED

3. Top LED

SMARTDISK

- 2 - INSTALLATION

2.1 MOUNTING

SMARTDISK may be set up on a solid and even surface. The mounting place must be of suﬃcient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the ﬁxture’s being used.

Fig.3

SMARTDISK

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Switch on the SMARTDISK with the power switch. The unit is ready for operation and can be operated via

a DMX controller or it independently performs its show program in succession.

After operation, switch oﬀ the unit with the power switch.

3.2 BASIC SETUP

The SMARTDISK has a OLED display and 4 buttons for access to the functions of the control panel (ﬁg. 5).

MENU ENTER UP DOWN

Used to access the menu or

to return a previous menu

option

Used to select and store the

current menu or confirm the

current function value or

option within a menu

Button to select the values

in ascending order of the

function

Button to select the values

in descending order of the

function

Fig.4 - Functions of the buttons

3.3 RECHARGE

To recharge the SMARTDISK:

• connect the unit to the battery charger using the input on the bottom of the TOP unit

• connect the charger to an electrical socket to start charging the battery

NOTE - Battery life: 8 hours 30 minutes with full white operation, charging time: max 5 hours.

SMARTDISK

3.4 MENU STRUCTURE

1 CONNECT

DMX Address

001 - 503

DMX mode

EASY 4 Ch

BASIC 8 Ch

STANDARD 17 Ch

EXTENDED 165 Ch

Wireless

Receive

Oﬀ

Reset Connect

Yes

IR Setting

Off

2 SETUP

Screen

Backlight

10s

20s

30s

Key lock

Yes

3 ADVANCED

Dimmer mode

Off

Dimmer 1

Dimmer 2

Dimmer 3

White Balance

Off

Adjust

Red

125 - 255

Green

125 - 255

Blue

125 - 255

White

125 - 255

Factory Reload

Yes

4 INFORMATIOJN

Fixture time

9999 H

Version

V 1.0

5 STAND ALONE

Effects

Eﬀect1

Speed 0~100

Background

Foreground

SMARTDISK

3.5 DMX ADDRESSING

To be able to operate the SMARTDISK with a light controller, set the unit DMX start address for the ﬁrst

DMX channel. To set the start address refer to following procedure:

• Use the UP/DOWN button until the display reads [DMX Address] and then press the ENTER button to

conﬁrm

• Press the UP/DOWN button to select the value [d 1-509] and then press the ENTER button .

If e. g. address 33 on the controller is provided for controlling the function of the ﬁrst DMX channel, adjust

the start address 33 on the SMARTDISK.

The other functions of the light eﬀect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown in the page 13.

DMX

Channels

number

Start address

(example)

Busy DMX

address

Next possible start address

for unit n°1

Next possible start address

for unit n°2

Next possible start address

for unit n°3

4 33 33-36 37 41 45

3.6 DMX MODE

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conﬁrm the setting.

• Press the MENU button repeatedly to exit the menu and save changes.

4 channels DMX configuration example

Eﬀect .......

Speed 0~100

Background

Foreground

Static Preset

Side

black,red,deep

orange, light

orange, yellow,

green, sea green,

acquamarine,

cyan, blue, violet,

purple, magenta,

white, white all,

warm white, cold

white

Top

Manual Color

Side

Red (0 - 255)

Top Green (0 - 255)

Blue (0 - 255)

White (0 - 255)

SMARTDISK

3.7 DMX CONFIGURATION

The SMARTDISK has 5 DMX channel conﬁgurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Users and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select User Mode and press ENTER to conﬁrm

your choice.

• Use the UP/DOWN button to select the desired DMX channel conﬁguration (Basic, Standard, Extended),

then press the ENTER button to conﬁrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

The tables on page 18 show the mode of operation and their values DMX.

The unit is equipped with 3/5-pole XLR connections.

3.8 WIRELESS CONTROL SETTINGS

To enable wireless control mode, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Wireless and press ENTER.

• Press the UP/DOWN and LEFT/RIGHT buttons to select the desired value (001-512).

• Press the ENTER key to conﬁrm the setting.

To change the settings of wireless control, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Wireless Set, and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select the option proposed and press the ENTER button to conﬁrm your

choice.

- Receive - Disable/enable the DMX signal cable. Select OFF to deactivate or ON to activate the func-

tion.

- Reset Connect - Reset the wireless connection of the unit. Select OFF to deactivate or ON to activate

the function.

• Press the ENTER button to conﬁrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

3.9 IR SETUP

To start up the IR recevitor refer to the following steps:

• Press the MENU button so many times until the display shows [IR Setup].

• Press the ENTER button to conﬁrm.

• Press the UP/DOWN button, select one of the programs [ON] or [OFF].

• Press the ENTER button for save the setting.

• Press the MENU button so many times until the display shows [Stand

Alone].

• Press the ENTER button to conﬁrm.

• Press the UP/DOWN button, select one of the programs [Static Present].

• Press the ENTER button for save the setting.

NOTE - Make sure to point the controller directly at the receiver on the

Fig.5

FADE

SOUND

SENSIT.

AUTO

MACRO

POWER

STROBESPEEDDIMMERMANUAL

AMBER

RED

YELLOW

CYAN

MAGENTA

STATIC

DEEP

ORANGE

LIGHT

ORANGE

SEA

GREEN

AQUA

MARINE

WARM

WHITE

COLD

WHITE

GREEN

BLUE VIOLET PURPLE

WHITE

SMARTDISK

product.

With the IR controller you can choose the desired color of the top and side part separately. The Static but-

ton allows you to move the color selection from the top to the side, the other way around. When selecting

a color for the top part, to move the selection to the side you must necessarily press the Static button

twice.

3.10 DISPLAY SETTINGS

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Setup icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select UI Set, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto Oﬀ. This feature allows you to automatically turn oﬀ the backlight

after a speciﬁed time that you can set using the arrow buttons. To have the display always on select

Always On or set a value of On - 10s - 20s - 30s to turn oﬀ the display after the amount of time you

choose.

- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function

is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-

tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, UP,

DOWN, ENTER. Select ON to activate or OFF to disable.

• Press the ENTER button to conﬁrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

3.11 RELOAD DEFAULT

Select this function to reset the unit to factory settings:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Factory Reload and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select ON or OFF, then press the ENTER button to conﬁrm.

3.12 WHITE BALANCE

Enter the White balance to adjust the Red, Green, Blue and White parameter to make diﬀerent whites.

• Press the button MENU so many times until shows White Balance, and press the button ENTER to conﬁrm.

• Select the color R, G, B, W through the buttons UP/DOWN, then press the button ENTER.

• Using UP/DOWN button, select the desired color value 125 - 255.

• Press ENTER button to continue to the next color R, G, B, W.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.13 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER but-

ton to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

SMARTDISK

Fig.6

DMX512 Controller

wireless

solution

and press the ENTER button to display it.

- Fixture Time - Through the Time Information function you can display the operating time of the

projector.

- Temperature - Through the Temperature function can be displayed the temperature inside the ﬁx-

ture, near the lamp. The temperature can be displayed in degrees Celsius or Fahrenheit.

- Version - Through Software Version function you can display the currently installed software version.

• Press the MENU button repeatedly to exit the menu.

3.14 OPERATION WITH WIFI

This mode allows you to wirelessly connect more SMARTDISK units, all managed through a unit W-DMX

transmitter (sold separately).

SMARTDISK

3.15 DMX CHANNELS

EASY

4CH

BASIC

8CH

STD

17CH

EXT

165CH

SMARTDISK

FUNCTION

DMX

Value

1 1 1

Side Red

0~100% 000 - 255

2 2 2

Side Green

0~100% 000 - 255

3 3 3

SideBlue

0~100% 000 - 255

4 4 4

Side White

0~100% 000 - 255

5 5

Top Red

0~100% 000 - 255

6 6

Top Green

0~100% 000 - 255

7 7

Top Blue

0~100% 000 - 255

8 8

Top White

0~100% 000 - 255

9 1 Dimmer

000 - 250

10 2

Strobe

Open

Strobe slow to fast

Open

Random slow to fast

Open

000 - 015

016 - 115

116 - 135

136 - 235

236 - 255

11 3

Effects

NO function

Effect 1

Effect 2

Effect 3

Effect 4

Effect 5

Effect 6

Effect 7

Random pixels

000 - 010

011 - 040

041 - 070

071 - 100

101 - 130

131 - 160

161 - 190

191 - 220

221 - 255

12 4

Effects speed

Static indexing

Forward Slow to fastest

Stop

Reverse Slow to fastest

000 - 050

051 - 150

151 - 155

156 - 255

13 5

Foreground Dimmer

0~100% 000 - 255

SMARTDISK

EASY

4CH

BASIC

8CH

STD

17CH

EXT

165CH

SMARTDISK

FUNCTION

DMX

Value

14 6

Foreground color

Black

Red

Green

Blue

White

Pastel red

Pastel green

Pastel blue

Cyan

Magenta

Yellow

Light Yellow

Light Blue

Light Magenta

Full white

000 - 000

001 - 018

019 - 036

037 - 054

055 - 072

073 - 090

091 -108

109 - 126

127 - 144

145 - 162

163 - 180

181 - 198

199 - 216

217 - 234

235 -255

15 7

Background Dimmer

0~100% 000 - 255

16 8

Background color

Black

Red

Green

Blue

White

Pastel red

Pastel green

Pastel blue

Cyan

Magenta

Yellow

Light Yellow

Light Blue

Light Magenta

Full white

000 - 000

001 - 018

019 - 036

037 - 054

055 - 072

073 - 090

091 -108

109 - 126

127 - 144

145 - 162

163 - 180

181 - 198

199 - 216

217 - 234

235 -255

17 9

Dimmer fade

Dimmer snap to fade

000 - 000

001 - 255

Pixel 1

Red 0~100%

Green 0~100%

Blue 0~100%

White 0~100%

000 - 255

....

.......

Red 0~100%

Green 0~100%

Blue 0~100%

White 0~100%

000 - 255

SMARTDISK

EASY

4CH

BASIC

8CH

STD

17CH

EXT

165CH

SMARTDISK

FUNCTION

DMX

Value

162

163

164

165

Pixel 39

Red 0~100%

Green 0~100%

Blue 0~100%

White 0~100%

000 - 255

SMARTDISK

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch oﬀ the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, ﬁxations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

Battery Guide

New Lithium Battery Initialisation

Any new fixture containing a Lithium battery should be initialised when first purchased to maximise its battery life.

To do this:

1. Fully charge the unit for a minimum of 5 to 6 hours.

2. Fully discharge, then fully recharge the battery.

3. Repeat this cycle another 2 times for optimum battery life.

Maximizing Battery Performance

1. Lithium batteries perform best when in regular use. Long idle periods will reduce the battery life.

2. Recharge the battery at the earliest opportunity, leaving batteries discharged for long periods will reduce battery life.

3. Store units containing Lithium batteries at cool temperatures. High ambient temperatures significantly reduce the life

of a Lithium battery.

4. Disconnect power from the unit when charging is complete.

5. Do not use fixtures whilst charging.

Long term storage

1. Charge your fixture’s battery to around 50%. If you store a fixture with a fully discharged battery, it could fall into a

deep discharge state. If you store it fully charged, the battery may lose some capacity, leading to shorter battery life.

2. Power down the device to avoid additional battery use.

3. Place your device in a cool, moisture-free environment that’s less than 32° C (90° F).

REV.003-08/17

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al fine di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modificare, in

qualunque momento e senza preavviso, le specifiche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

La pagina sta caricando ...

ProLights Full colour and pixel controlled table centre Manuale utente

Marca: ProLights

Modello: Full colour and pixel controlled table centre

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights Full colour and pixel controlled table centre User manual

ProLights Full colour and pixel controlled table centre Manuale utente

ProLights Full colour and pixel controlled table centre Manuale utente

in altre lingue

Documenti correlati

Altri documenti