Dolmar MS-20C Manuale del proprietario

Brush Cutter/Grass Trimmer

Débroussailleuse/Taille-bordures

Motorsense/Rasentrimmer

Decespugliatore/Tagriabordi

Bosmaaier/Strimmer

Desbrozadora/Cortabordes

ORIGINAL INSTRUCTION MANUAL MANUALE DI ISTRUZIONI ORIGINALE

MANUEL D’INSTRUCTIONS ORIGINAL ORIGINELE GEBRUIKSAANWIJZING

ORIGINALBEDIENUNGSANLEITUNG MANUAL DE INSTRUCCIONES ORIGINAL

MS-20U

MS-20C

Important:

Read this instruction manual carefully before putting the Grass Trimmer into operation and strictly observe the safety regulations!

Preserve instruction manual carefully!

Recommandation importante:

Lire soigneusement ce manuel d’instructions avant de mettre la débroussailleuse en service et observer rigoureusement les

consignes de sécurité! Conserver soigneusement ce manuel d’instructions.

Wichtlg:

Bitte lesen Sie dieses Anweisungshandbuch sorgfältig durch, bevor Sie den Motorsense in Betrieb nehmen, und beachten Sie die

Sicherheitsvorschriften strikt! Bewahren Sie das Anweisungshandbuch sorgfältig auf.

Importante:

Prima di mettere in funzione il Strimmer, leggere attentamente il presente manuale; rispettare rigorosamente le norme di sicurezza!

Conservare il manuale delle istruzioni per l’uso!

Belangrijk:

Lees voor het in gebruik nemen van de bosmaaier deze gebruiksaarwijzing zorgvuldig door en neem alle veiligheidsvoorschriften in

acht. Bewaar de gebruiksaanwijzing voor eventuele naslag.

Importante:

Leer cuidadosamente este manual de instrucciones antes de poner en marcha la máquina y observar estrictamente las normas de

seguridad. Conservar este manual de instrucciones con cuidado.

English/Français

/

German

/

Italiano/Dutch/Spanish

MS-20U

MS-20C

㩷

2

Thank you very much for purchasing the DOLMAR Brush cutter or Grass

trimmer. We are pleased to recommend to you the DOLMAR Brush cutter

or Grass trimmer which is the result of a long development programme and

many years of knowledge and experience.

Please read this booklet which refers in detail to the various points that will

demonstrate its outstanding performance. This will assist you to obtain the

best possible result from your DOLMAR Brush cutter or Grass trimmer.

Table of Contents Page

Symbols.......................................................................2

Safety instructions........................................................3

Technical data ............................................................. 7

Designation of parts .....................................................8

Assembly of engine and shaft ......................................9

Mounting of handle ....................................................10

Mounting of protector ................................................. 11

Mounting of cutter blade or nylon cutting head ........... 12

Fuels/Refuelling ......................................................... 13

Correct handling of machine ...................................... 14

Putting into operation ............................................14-15

Idle adjustment...........................................................15

Resharpening the cutting tool..................................... 16

Nylon cutting head ................................................16-17

Servicing instructions ............................................17-18

Storage ...................................................................... 19

SYMBOLS

You will note the following symbols when reading the instructions manual.

Read instruction Manual

Wear protective helmet, eye and ear

protection (for Brush Cutter only)

Take Particular Care and Attention

Do not use metal blades (for grass

trimmer only)

Forbidden

Top permissible tool speed

Keep distance

Fuel and oil mixture

Flying object hazard

Engine-Manual start

No smoking

Emergency stop

No naked flame

First Aid

Protective gloves must be worn

Recycling

Kickback

ON/START

Keep the area of operation clear of all

persons and pets

OFF/STOP

Wear eye and ear protection (for grass

trimmer)

EC-Mark

English

㩷

3

SAFETY INSTRUCTIONS

General Instructions

– To ensure correct operation, user has to read this instruction manual to make

himself familiar with the handling of the Brush cutter or Grass trimmer.

Users insufficiently informed will risk danger to themselves as well as others

due to improper handling.

– It is recommended only to lend the Brush cutter or Grass trimmer to lend the

Brush cutter or Grass trimmer to people who have proven to be experienced

with Brush cutter or Grass trimmers.

Always hand over the instruction manual.

– First users should ask the dealer for basic instructions to familiarize oneself

with the handling of an engine powered cutter or trimmer.

– Children and young persons aged under 18 years must not be allowed to

operate the Brush cutter or Grass trimmer. Persons over the age of 16

years may however use the device for the purpose of being trained only

whilst under supervision of a qualified trainer.

– Use Brush cutter or Grass trimmers with the utmost care and attention.

– Operate the Brush cutter or Grass trimmer only if you are in good physical

condition. Perform all work calmly and carefully. The user has to accept

liability for others.

– Never use the Brush cutter or Grass trimmer after consumption of alcohol or

drugs, or if feeling tired or ill.

– National regulation can restrict the use of the machine.

㩷

Intended use of the machine

– The Brush cutter or Grass trimmer is only intended for cutter grass, weeds,

Bushes, undergrowth it should not be used for any other purpose such as

Edging or hedge cutting as this may cause injury.

㩷

Personal protective equipment

– The clothing worn should be functional and appropriate, i.e. it should be

tight-fitting but not cause hindrance. Do not wear either jewelry or clothing

which could become entangled with bushes or shrubs.

– In order to avoid either head-, eye-, hand-or foot injuries as well to protect

your hearing the following protective equipment and protective clothing must

be used during operation of the Brush cutter or Grass trimmer.

– Always wear a helmet where there is a risk of falling objects. The protective

helmet (1) is to be checked at regular intervals for damage and is to be

replaced at the latest after 5 years. Use only approved protective helmets.

– The visor (2) of the helmet (or alternatively goggles) protects the face from

flying debris and stones. During operation of the Brush cutter or Grass

trimmer always wear goggles, or a visor to prevent eye injuries.

– Wear adequate noise protection equipment to avoid hearing impairment (ear

muffs (3), ear plugs etc.).

– The work overalls (4) protect against flying stones and debris.

We strongly recommend that the user wears work overalls.

– Special gloves (5) made of thick leather are part of the prescribed equipment

and must always be worn during operation of the Brush cutter or Grass

trimmer.

– When using the Brush cutter or Grass trimmer, always wear sturdy shoes (6)

with a non-slip sole. This protects against injuries and ensures a good

footing.

㩷

Starting up the Brush cutter or Grass trimmer

– Please make sure that there are no children or other people within a working

range of 15 meters (49ft), also pay attention to any animals in the working

vicinity.

– Before use always check that the Brush cutter or Grass trimmer is safe for

operation:

Check the security of the cutting tool, the control lever for easy action and

check for proper functioning of the control lever lock.

– Rotation of the cutting tool during idling speed is not allowed. Check with

your dealer for adjustment if in doubt. Check for clean and dry handles and

test the function of the start/stop switch.

㩷

Diagrammatic figure

15meters

㩷

4

3 meters

Start the Brush cutter or Grass trimmer only in accordance with the

instructions.

Do not use any other methods for starting the engine!

– Use the Brush cutter or Grass trimmer and the tools only for such applications

as specified.

– Only start the Brush cutter or Grass trimmer engine, after the entire assembly

is done. Operation of the device is only permitted after all the appropriate

accessories are attached!

– Before starting make sure that the cutting tool has no contact with hard

objects such as branches, stones etc. as the cutting tool will revolve when

starting.

– The engine is to be switched off immediately in case of any engine problems.

– Should the cutting tool hit stones or other hard objects, immediately switch off

the engine and inspect the cutting tool.

– Inspect the cutting tool at short regular intervals for damage (detection of

hairline cracks by means of tapping-noise test).

– Operate the Brush cutter or Grass trimmer only with the shoulder strap

attached which is to be suitably adjusted before putting the Brush cutter or

Grass trimmer into operation. It is essential to adjust the shoulder strap

according to the use’s size to prevent fatigue occurring during use. Never

hold the cutter with one hand during use.

– During operation always hold the Brush cutter or Grass trimmer with both

hands.

Always ensure a safe footing.

– Operate the Brush cutter or Grass trimmer in such a manner as to avoid

inhalation of the exhaust gases. Never run the engine in enclosed rooms

(risk of gas poisoning). Carbon monoxide is an odorless gas.

– Switch off the engine when resting and when leaving the Brush cutter or

Grass trimmer unattended, and place it in a safe location to prevent danger to

others or damage to the machine.

– Never put the hot Brush cutter or Grass trimmer onto dry grass or onto any

combustible materials.

– The cutting tool has to be equipped with it’s appropriate guard.

Never run the cutter or trimmer without this guard!

– All protective installations and guards supplied with the machine must be used

during operation.

– Never operate the engine with faulty exhaust muffler.

– Shut off the engine during transport.

– During transport over long distances the tool protection included with the

equipment must always be used.

– Ensure safe position of the Brush cutter or Grass trimmer during car

transportation to avoid fuel leakage.

– When dispatching the Brush cutter or Grass trimmer, ensure that the fuel tank

is completely empty.

– When unloading the Brush cutter or Grass trimmer from the truck, never drop

the Engine to the ground or this may severely damage the fuel tank.

– Except in case of emergency, never drop or cast the Brush cutter or Grass

trimmer to the ground or this may severely damage the Brush cutter or Grass

trimmer

– Remember to lift the entire equipment from the ground when moving the

equipment. Dragging the fuel tank is highly dangerous and will cause

damage and leakage of fuel, possibly causing fire.

㩷

Refuelling

– Shut off the engine during refuelling, keep away from naked flames and do not

smoke.

– Avoid skin contact with mineral oil products. Do not inhale fuel vapor.

Always wear protective gloves during refuelling. Change and clean

protective clothing at regular intervals.

– Take car not to spill either fuel or oil in order to prevent soil contamination

(environmental protection). Clean the Brush cutter or Grass trimmer

immediately after fuel has been spilt.

– Avoid any fuel contact with your clothing. Change your clothing instantly if

fuel has been spilt on it (to prevent clothing catching fire).

– Inspect the fuel cap at regular intervals making sure that it can be securely

fastened and does not leak.

– Carefully tighten the fuel tank cap. Change location to start the engine (at

least 3 meters away from the place of refuelling).

– Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk

of explosions).

– Only transport and store fuel in licensed containers. Make sure the fuel

stored is not accessible to children.

㩷

 Resting

 Transport

 Refuelling

 Maintenance

 Tool Replacement

㩷

5

Method of operation

– Only use the Brush cutter or Grass trimmer in good light and visibility.

During the winter season beware of slippery or wet areas, ice and snow (risk

of slipping). Always ensure a safe looting.

– Never cut above waist height.

– Never stand on a ladder and run the Brush cutter or Grass trimmer.

– Never climb up into trees to perform cutting operation with the Brush cutter or

Grass trimmer.

– Never work on unstable surfaces.

– Remove sand, stones, nails etc. found within the working range.

Foreign particles may damage the cutting tool and can cause dangerous

kick-backs.

– Before commencing cutting, the cutting tool must have reached full working

speed.

㩷

Kickback

– When operating the Brush cutter or Grass trimmer, uncontrolled kickback

may occur.

– This is particularly the case when attempting to cut within a blade segment

between 12 and 2 o’clock.

– Never apply the Brush cutter or Grass trimmer within a segment between 12

and 2 o’clock.

– Never apply this segment of the Brush cutter or Grass trimmer blade to solids,

such as bushes and trees, etc., having a diameter in excess of 3 cm or the

Brush cutter or Grass trimmer will be deflected at great force with the risk of

injuries.

㩷

Kickback prevention

To avoid kickbacks, observe the following:

– Operation within a blade segment between 12 and 2 o’clock presents positive

hazards, especially when using metal cutting tools.

– Cutting operations within a blade segment between 11 and 12 o’clock, and

between 2 and 5 o’clock, must only be performed by trained and experienced

operators, and then only at their own risk.

Easy cutting with almost no kickback is possible within a blade segment

between 8 and 11 o’clock.

㩷

Cutting Tools

Employ only the correct cutting tool for the job in hand.

MS-20U with cutter blade (Star Blade (4 teeth))

MS-20C with Nylon cutting head

For cutting thick materials, such as weed, high grass, bushes, shrubs,

underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work

by swinging the Brush cutter or Grass trimmer evenly in half-circles from right to

left (similar to using a scythe).

㩷

Maintenance instructions

– The condition of the cutter or trimmer, in particular of the cutting tool of the

protective devices and also of the shoulder strap must be checked before

commencing work. Particular attention is to be paid to the cutting blades

which must be correctly sharpened.

– Turn off the engine and remove spark plug connector when replacing or

sharpening cutting tools, and also when cleaning the cutter or cutting tool.

㩷

Caution:

Kickback

Diagrammatic

figure

Diagrammatic

figure

㩷

6

Never straighten or weld damaged cutting tools.

– Operate the Brush cutter or Grass trimmer with as little noise and

contamination as possible. In particular check the correct setting of the

carburetor.

– Clean the Brush cutter or Grass trimmer at regular intervals and check that all

screws and nuts are well tightened.

– Never service or store the Brush cutter or Grass trimmer in the vicinity of

naked flames.

– Always store the Brush cutter or Grass trimmer in locked rooms and with an

emptied fuel tank.

Observe the relevant accident prevention instructions issued by the relevant trade associations and by the insurance companies.

Do not perform any modifications on the Brush cutter or Grass trimmer as this will endanger your safety.

The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All other work

is to be done by an Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by DOLMAR.

Use of non-approved accessories and tools means increased risk of accidents.

DOLMAR will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting tools,

or accessories.

First Aid

In case of accident make sure that a first-aid box is available in the vicinity of

the cutting operations. Immediately replace any item taken from the first aid

box.

When asking for help, please give the following information:

– Place of accident

– What happened

– Number of injured persons

– Kind of injuries

– Your name

Packaging

The DOLMAR Brush cutter or Grass trimmer will be delivered in two protective

cardboard boxes to prevent transport damage. Cardboard is a basic raw

material and is therefore consequently reusable or suitable for recycling (waste

paper recycling).

EC-DECLARATION OF CONFORMITY

Brush Cutter / Grass Trimmer: model MS-20U, MS-20C (See TECHNICAL DATA for the specifications)

We declare under our sole responsibility that this product is in compliance with the following Directives, 2000/14/EC, 2006/42/EC.

The most important standards applied to properly meet the requirements of the above Directives were: EN11806.

Measured Sound Power: 108.5 dB

Guarantee Sound Power: 110.5 dB

These sound power levels were measured in accordance with Council Directive, 2000/14/EC.

Conformity assessment procedure: Annex V.

3rd. NOV. 2009

Tamiro Kishima Rainer Bergfeld

Managing Director Managing Director

Responsible Manufacturer:

Makita Corporation.

3-11-8,Sumiyoshi-cho, Anjo, Aichi, JAPAN

Authorized Representative in Europe:

DOLMAR Gmbh

Jenfelder Str. 38, 22045 Hamburg, Germany

㩷

7

TECHNICAL DATA MS-20U, MS-20C

MS-20U MS-20C

U handle Loop handle

Model

Cutter blade Nylon cutting head

Dimensions : length x width x height (without cutting blade) mm

1735x640x405 1735x340x200

Mass (without plastic guard and cutting blade) kg

3.9 3.6

Volume (fuel tank) cm

3

400

Engine displacement cm

3

20.0

Maximum engine performance kw

0.57 / 7000 min

-1

Engine speed at recommended max. spindle speed min

-1

8800

Maximum spindle speed (corresponding) min

-1

6000

Fuel consumption kg/h

0.44

Specific fuel consumption g/kwh

650

Idling speed min

-1

3000

Clutch engagement speed min

-1

4000

Carburetor (Diaphragm - carburetor) type

TK TZ9V

Ignition system type

Solid state ignition

Spark plug type

NGK BPMR7A

Electrode gap mm

0.6 - 0.7

a

hv eq

m/s

2

2.4 4.2

Right handle

(Rear grip)

Uncertainty K m/s

2

0.8 1.0

a

hv eq

m/s

2

4.3 5.8

Vibration per

ISO 22867

Left handle

(Front grip)

Uncertainty K m/s

2

0.4 1.8

L

PA eq

dBA

93.2 96.2

Sound pressure level average to

ISO 22868

Uncertainty K dBA

3.6 2.5

L

WA eq

dBA

101.6 106.7

Sound power level average to

ISO 22868

Uncertainty K dBA

2.1 1.6

Mixture ratio

50 : 1

Gear ratio

14/19

* WARNING: MODEL MS-20U, MS-20C must not be used with a saw blade.

㩷

8

DESIGNATION OF PARTS

㩷

GB DESIGNATION OF PARTS

1 Fuel Tank

2 Rewind Starter

3 Air Cleaner

4 I-O Switch (on/off)

5 Spark Plug

6 Exhaust Muffler

7 Clutch Case

8 Rear Grip

9 Hanger

10 Handle

11 Control Lever

12 Control Cable

13 Shaft

14 Protector

15 Gear Case/Head Case

16 Handle Holder

17 Cutter Blade

18 Nylon Cutting Head

20 Fuel Filler Cap

21 Starter Knob

24 Exhaust Pipe

MS-20U

Br

us

h

cutte

r

MS-20C

G

r

ass

Trimm

e

r

㪉㪈㩷

㪉㪋

㽴

㾅

㽶

㽺

㽲

㽸

㽻

㾁

㽵

㽼

㽽

㾀

㾂

㽿

㽾

㾀

㾃

㽿

㽾

㽷

㽶

㽴

㾅

㽹

㽼

㽸

㽵

㽺

㽻

㽲

㽽

㽶

㽴

㽷

㽲

㾅

㽳

㩷

9

㩷

ASSEMBLY OF ENGINE AND SHAFT

CAUTION: Before doing any work on the Brush cutter or Grass Trimmer,

always switch off the engine and pull the spark plug connector off

the spark plug. Always wear protective gloves!

CAUTION: Start the Brush cutter or Grass Trimmer only after having

assembled it completely.

– Insert the drive shaft into the holder case (Fig).

Note: Always insert the drive shaft into the Clutch case fully (approx. 58 mm).

If the inner shaft resists full insertion of the drive shaft, try to insert it

again after slightly rotating the drive shaft or the support washer on the

gear case to match the inner shaft to the hole inside the holder case.

– After making sure that the drive shaft is installed fully and properly, tighten

the socket head bolt (M5 x 14) and socket head bolt (M5 x 25) to secure the

drive shaft.

– Put the carburetor bracket (3) between the 2 nuts (M6) (2) attached to the

control cable (1) and tighten the 2 nuts (2) ensuring that the distance (a) to the

tip of the screw of the control cable is 3.0 to 4.0 mm. Then, insert the nipple of

the control cable into the swivel (4) of the carburetor.

Connect the switch cords to the two cords from the engine by inserting one into

the other.

– Fix the cord connector by clamp.

㩷

Clutch case

Socket head

bolt (M5x25)

Socket head

bolt (M5x14)

Drive shaft

Connectors

(1)

(3)

(2)

(4)

(a)

㩷

10

MOUNTING OF HANDLE

CAUTION: Before doing any work on the Brush cutter or Grass trimmer, always

switch off the motor and pull the spark plug connector off the spark

plug.

Always wear protective gloves!

CAUTION: Start the Brush cutter or Grass trimmer only after having assembled

it completely.

For machines with U Handle models

– Place the handle-fixing metal so that the handle with the control lever will be

positioned on the right (the right-hand grip side) as viewed from the engine

side, and the other handle on the left side.

– Fit the groove of the handle-fixing material to the handle end. Fix provisionally

the attached metal by hexagon socket bolt supplied.

– Adjust the handle to an easy-to-operate position, and tighten securely the

four hexagon socket bolts uniformly on the right and left by Allen wrench.

– Fasten the cable onto shaft which clip wire as shown in the diagram for

comfortable operation.

For machines with Loop Handle (CEN)

– Fix a barrier to the left side of the machine together with the handle for

operator’s protection.

– Do not adjust position of the loop handle too close to the control grip. Keep

not less than 25 cm distance between the handle and the grip.

(a distance collar is provided for this purpose.)

㩷

Clip wire

㩷

to engine

MS-20U

MS-20C

㩷

11

MOUNTING OF PROTECTOR

To meet the applicable safety provisions, only the tool/protector combinations

as indicated in the table must be used.

Be sure to use genuine DOLMAR cutter blades or nylon cutting head.

– The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine

and check the blade immediately.

– Polish or replace the cutter blade every three hours of operation.

– The outside diameter of the cutter blade must be 230mm (9-1/16"). Never use any blades surpassing 230mm (9-1/16") in outside diameter.

㩷

Star Blade Eddy Blade Protector for metal blades Nylon cutting head Protector for cord cutter

㩷

CAUTION: The appropriate protector must always be installed, for your own safety and in order to comply with accident-prevention regulations.

Operation of the equipment without the guard being in place is not permitted.



– Fix the protector (1) to the clamp (3) with two bolts M6 x 30 (2).

㩷

– When using the string head, fit the protector (6) into the protector (1), and

tighten them with two nuts (5) and two screws (4).

㩷

(6)

(5)

(4)

(1)

㩷

12

MOUNTING OF CUTTER BLADE OR NYLON CUTTER HEAD

Turn the machine upside down, and you can replace the cutter blade or the nylon cutting head easily.

– Insert the hex wrench through the hole in the gear case and rotate the

receiver washer (3) until it is locked with the hex wrench.

– Loosen the nut (1) (left-hand thread) with the socket wrench and remove the

nut (1), and clamp washer (2).

with the hex wrench still in place.

– Mount the cutter blade onto the shaft so that the guide of the receiver washer

(3) fits in the arbor hole in the cutter blade. Install the clamp washer (2) and

secure the cutter blade with the nut (1).

[Tightening torque: 130 - 230 kg-cm]

NOTE: Always wear gloves when handling the cutter blade.

NOTE: The cutter blade-fastening nut (with spring washer) is a consumable

part. If there appears any wear or deformation on the spring washer,

replace the nut.

NOTE: The clamp washer (2), and nut (1) are not necessary for mounting the

nylon cutting head. The nylon head should go on top of the receiver

washer (3).

– Screw the nylon cutting headd onto the shaft.

– Make sure that the blade is the left way up.

㩷

(3)

(1)

(2)

(3)

Tighten

Hex wrench

Rotation

Loosen

㩷

13

FUELS/REFUELLING

Handling fuel

Utmost care is required when handling fuel. Fuel may contain substances

similar to solvents. Refuel either in a well ventilated room or outdoors. Do

not inhale fuel vapors, avoid any contact of fuel or oil with your skin.

Mineral oil products degrease your skin. If your skin comes in contact with

these substances repeatedly and for an extended period of time, it will

desiccate. Various skin diseases may result. In addition, allergic reactions are

known to occur. Eyes can be irritated by contact with oil. If oil comes into

your eyes, immediately wash them with clear water. If your eyes are still

irritated, see a doctor immediately!

Fuel and oil mixture

The engine of the Brush cutter or Grass trimmer is a high-efficiency two-stroke

engine. It is run with a mixture of fuel and two-stroke engine oil. The engine

is designed for unleaded regular fuel with a min. octane value of 91 RON. In

case no such fuel is available, you can use fuel with a higher octane value.

This will not affect the engine, but may cause poor operating behaviour.

A similar situation will arise from the use of leaded fuel. To obtain optimum

engine operation and to protect your health and the environment, only unleaded

fuel should be used!

For lubricating the engine use a two-stroke engine oil (quality grade: TC-3),

which is added to the fuel. The engine has been designed to use specified

two-stroke engine oil at mixture ratio of 50:1 to protect the environment. In

addition, a long service life and a reliable operation with a minimum emission of

exhaust gases is guaranteed. It is absolutely essential to observe a mixture

ratio of 50:1 (specified 2-stroke engine oil), as otherwise reliable function of the

Brush cutter or Grass trimmer cannot be guaranteed.

The correct mixture ratio:

Gasoline : Specified two-stroke engine oil = 50 : 1 or

Gasoline : Other manufacturer’s two-stroke engine oil = 25 : 1

recommended

㩷

NOTE: For preparing the fuel-oil mixture first mix the entire oil quantity with half

of the fuel required, then add the remaining fuel. Thoroughly shake

the mixture before filling it into the Brush cutter or Grass trimmer tank.

It is not wise to add more engine oil than specified to ensure safe

operation.

This will only result in a higher production of combustion residues which

will pollute the environment and clog the exhaust channel in the cylinder

as well as the muffler. In addition, the fuel consumption will rise and

the performance will decrease.

Refuelling

The engine must be switched off!

– Thoroughly clean the area around the fuel filler cap (2), to prevent dirt from

getting into the fuel tank (1).

– Unscrew the fuel filler cap (2) and fill the tank with fuel.

– Tightly screw on the fuel filler cap (2).

– Clean screw fuel filler cap (2) and tank after refueling!

㩷

Storage of Fuel

Fuel cannot be stored for an unlimited period of time.

Purchase only the quantity required for a 4 week operating period. Only use

approved fuel storage containers.

Observe the Safety Instructions on page 4!

㩷

Gasoline 50:1 25:1

䋫

䋫䋫

䋫

1000 mL (1 L) 20 mL 40 mL

5000 mL (5 L) 100 mL 200 mL

10000 mL (10 L) 200 mL 400 mL

㩷

(2)

(1)

㩷

14

CORRECT HANDLING OF MACHINE

Attachment of shoulder strap

– Adjust the strap length so that the cutter blade or the Nylon cutting head will

be kept parallel with the ground.

Detachment

– In an emergency, push the notches (1) at both sides, and you can detach the

machine from you.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deflected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

PUTTING INTO OPERATION

Observe the applicable accident prevention regulations!

Starting

Move at least 3m away from the place of refuelling. Place the Brush cutter or Grass trimmer on a clean piece of ground taking care that the

cutting tool does not come into contact with the ground or any other objects.

Cold start

For machine with U Handle or Loop Handle

– Push the I-O switch (1) in the direction shown by the arrow.

– First place the machine on the ground.

– Give a gentle push on the primer pump (1) repeatedly (7-10 times) until lfuel

comes into the primer pump.

– Push the choke button (2) to the position “ ”

㩷

Han

g

er

㩷

15

– Firmly hold the clutch case by your left hand, as illustrated.

– Slowly pull the starter grip until resistance is felt and continue with a smart

pull.

– Do not pull out the starter rope to its full extent and do not allow the starter

handle to be retracted without control, but ensure that it is retracted slowly.

– Repeat the starting operation until initial ignitions are heard.

– When the engine starts, please open the throttle lever a little. The choke

button being automatic, it returns to original position “ ”.

– Run the engine for approximately one minute at a moderate speed before applying full throttle.

Note: − If the starter handle is pulled repeatedly when the choke button remains at “ ” position, the engine will not start easily due to

excessive fuel intake.

− In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also, dry the

electrode section of the spark plug.

Caution during operation:

If the throttle lever is opened fully in a no-load operation, the engine rotation is increased to 10,000rpm or more. Never operate the engine at a

higher speed than required and at an approximate speed of 6,000 - 8,000rpm.

Starting the warm engine

– As described above, except without moving the choke button.

Stopping

– Release the throttle lever (2) fully, and when the engine rpm has lowered,

push the I-O switch (1) to “O” position the engine will now stop.

– Be aware that the cutting head may not stop immediately and allow it to slow

down fully.

IDLE ADJUSTMENT

The cutter blade or the nylon cutting head should not run when the control lever is fully released. If necessary, adjust the idle rpm using the

idle adjusting screw.

㩷

Checking the Idling speed

– Idle speed should be set to 3,000rpm.

If necessary correct it by means of the idle screw (the blade or the nylon

cutting head must not turn when the engine is on idle).

Screwing in the screw (1) will cause an increase in the engine speed,

whereas backing off the screw will reduce the engine speed.

㩷

Slow Hi

g

h

㩷

16

RESHARPENING THE CUTTING TOOL

CAUTION: The cutting tools mentioned below must only be resharpened by an

authorized facility. Manual resharpening will result in imbalances

of the cutting tool causing vibrations and damage to the equipment.

– cutter blade (star blade (4 teeth), eddy blade (8 teeth))

An expert resharpening and balancing service is provided by Authorized

Service Agents.

NOTE: To increase the service life of the cutter blade (star blade, eddy blade) it

may be turned over once, until both cutting edges have become blunt.

NYLON CUTTING HEAD

The nylon cutting head is a dual string trimmer head capable of both automatic and bump & feed mechanisms.

The nylon cutting head will automatically feed out the proper length of nylon cord by the changes in centrifugal force caused by increasing or

decreasing RPMS. However, to cut soft grass more efficiently, bump the nylon cutting head against the ground to feed out extra cord as

indicated under operation section.

Operation

– Increase the nylon cutting head speed to approx. 6,000rpm.

Low speed (under 4,800rpm) is not suitable, the nylon cord will not feed out

properly at low speed.

– The most effective cutting area is shown by the shaded area.

If the nylon cord does not feed out automatically proceed as follows:

1. Release the throttle lever to run the engine idle and then squeeze the throttle

lever fully. Repeat this procedure until the nylon cord feeds out to the

proper length.

2. If the nylon cord is too short to feed out automatically with the above

procedure, bump the knob of the nylon cutting head against the ground to

feed out the nylon cord.

3. If the nylon cord does not feed out with procedure 2, rewind/replace the

nylon cord by following the procedures described under “Replacing the nylon

cord”.

Replacing the nylon cord

– First, stop the engine.

– Press on the housing latches inward to lift off the cover, then remove the

spool.

– Hook the center of new nylon cord into the notch in the center of the spool,

with one end of the cord extending about 80mm (3-1/8") more than the other.

Then wind both ends firmly around the spool in the direction of the head

rotation (left-hand direction indicated by LH and right-hand direction by RH on

the side of the spool).

㩷

Most effective cutting area

㩷

Idle speed Full speed

Knob

Cover

80mm(3-1/8”)

Press

Latches

Spool

For left hand

rotation

Spool

Press

㩷

17

– Wind all but about 100mm (3-15/16") of the cords, leaving the ends

temporarily hooked through a notch on the side of the spool.

– Mount the spool in the housing so that the grooves and protrusions on the

spool match up with those in the housing. Keep the side with letters on the

spool visible on the top. Now, unhook the ends of the cord from their

temporary position and feed the cords through the eyelets to come out of the

housing.

– Align the protrusion on the underside of the cover with the slots of the eyelets.

Then push cover firmly onto the housing to secure it.

SERVICING INSTRUCTIONS

㩷

COUTION: Before doing any work on the Brush cutter or Grass trimmer, always switch off the motor and pull the plug cap off the spark plug

(see “checking the spark plug”).

Always wear protective gloves!

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

Daily checkup and maintenance

– Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade or nylon

cutting head.

– Before operation, always check for clogging of the cooling air passage and the cylinder fins.

Clean them if necessary.

– Perform the following work daily after use:

• Clean the Brush cutter or Grass trimmer externally and inspect for damage.

• Clean the air filter. When working under extremely dusty conditions, clean the filter the severall times a day.

• Check the blade or the nylon cutting head for damage and make sure it is firmly mounted.

• Check that there is sufficient difference between idling and engagement speed to ensure that the cutting tool is at a standstill while the

engine is idling (if necessary reduce idling speed).

If under idling conditions the tool should still continue to run, consult your nearest Authorized Service Agent.

– Check the functioning of the I-O switch, the lock-off lever, the control lever.

Cleaning of air cleaner

Clogging of the element (1) may sometimes make it difficult or impossible to

start up the engine or increase the engine speed.

After the end of operation, be sure to clean the air cleaner as mentioned below.

– Remove the air cleaner cover screw.

– Place the finger under the air cleaner cover, push down the cover lower part,

and detach the air cleaner cover.

– Take out the element (1), clean it with lukewarm water mixed with neutral

detergent, and dry it completely.

㩷

100 mm (3-15/16’’)

Eyelets

Cover

Protrusion

Slot of eyelet

Notches

㩷

18

㩷

– After cleaning, attach the element.

– Insert the claw at the case upper part into the hole at the upper part of the air

cleaner cover. Then, attach the air cleaner cover by pushing it, and tighten

the screw (2).

NOTE: If there is excessive dust or dirt adhering to the air cleaner, clean it

every day. A clogged air cleaner may make it difficult or impossible to

start the engine or increase the engine rotational speed.

Checking the spark plug

– Only use the supplied universal wrench to remove or to install the spark plug.

– The gap between the two electrodes of the spark plug should be 0.6 - 0.7mm

(0.024" - 0.028"). If the gap is too wide or too narrow, adjust it. If the spark

plug is clogged with carbon or fouled, clean it thoroughly or replace it.

COUTION: Never touch the spark plug connector while the engine is running

(danger of high voltage electric shock).

Supply of grease to gear case

– Supply grease (Shell Alvania 3 or equivalent) to the gear case through the

grease hole every 30 hours. (Genuine DOLMAR grease may be purchased

from your DOLMAR dealer.)

Suction head in the fuel tank

– The felt filler (1) of the suction head is used to filler the fuel required by the

carburetor.

– A periodical visual inspection of the felt filter is to be conducted. For that

purpose open the tank cap, use a wire hook and pull out the suction head

through the tank opening. Filters found to have hardened, been polluted or

clogged up are to be replaced.

– Insufficient fuel supply can result in the admissible maximum speed being

exceeded. It is therefore important to replace the felt filter at least quarterly

to ensure satisfactory fuel supply to the carburetor.

Cleaning of muffler exhaust port

– Check of muffler exhaust port (2) regularly.

– If it is clogged by carbon deposits, carefully scratch the deposits out with a

suitable tool.

Any maintenance of adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

㩷

Gear case

Grease hole

(1)

(2)

㩷

19

STORAGE

– When the machine is in storage for a long time, drain fuel from the fuel tank

and carburetor, as follows: Drain all fuel from the fuel tank. Dispose of

properly and in accordance with all local laws.

– Remove the spark plug and a few drops of oil into the spark plug hole. Then,

pull the starter gently, so that oil covers the engine inside and tighten the

spark plug.

– Clear dirt or dust from the cutter blade or the nylon cutting head and outside

of engine, wipe them with a oil-immersed cloth and keep the machine in a

place as dry as possible.

Maintenance schedule

General

Engine assembly, screws and

nuts

Visual inspection for damage and tightness

Check for general condition and security

After each refuelling

Control lever

I-O-switch

Functional check

Daily

Air filter

Cooling air duct

Cutting tool

Idling speed

To be cleaned

To be Cleaned

Check for damage and sharpness

Inspection (cutting tool must not move)

Weekly

Spark plug

Muffler

Inspection, replace if necessary

Check and if necessary clean the opening

Quarterly

Suction head

Fuel tank

To be replaced

To be cleaned

Shuting down procedure

Fuel tank

Carburetor

Empty fuel tank

Operate until engine runs out of fuel

Fault location

Fault System Observation Cause

Engine not starting or with

difficulty

Ignition system Ignition spark O.K.

Fault in fuel supply or compression system, mechanical

defect

No ignition spark

STOP-switch operated, wiring fault or short circuit, spark

plug or connector defective, ignition module faulty

Fuel supply Fuel tank filled

Incorrect choke position, carburetor defective, fuel supply

line bent or blocked, fuel dirty.

Compression

No compression when

pulled over

Cylinder bottom gasket defective, crankshaft seals

damaged, cylinder or piston rings defective or improper

sealing of spark plug

Mechanical fault Starter not engaging Broken starter spring, broken parts inside of the engine

Warm start problems

Tank filled ignition spark

existing

Carburetor contaminated, have it cleaned

Engine starts but dies Fuel supply Tank filled Incorrect idling adjustment, carburetor contaminated

Fuel tank vent defective, fuel supply line interrupted,

cable or STOP-switch faulty

Insufficient performance

Several systems

may simultaneously

be affected

Engine idling poor

Air filter contaminated, carburetor contaminated, muffler

clogged, exhaust duct in the cylinder clogged

㩷

Drain fuel

Humidit

y

㩷

20

Nous vous remercions d'avoir fait l'acquisition de la débroussailleuse /

taille-bordures DOLMAR. Nous sommes heureux de pouvoir vous

conseiller la débroussailleuse / taille-bordures DOLMAR qui représente le

résultat d'un long programme de développement et de plusieurs années de

recherche et d'expérience.

Veuillez lire cette brochure qui fait référence en détail aux différents points

témoignant de l'efficacité exceptionnelle de votre débroussaileuse

DOLMAR.

Table des matières Page

Symboles...................................................................20

Consignes de sécurité................................................21

Caractéristiques techniques.......................................25

Nomenclature des pièces...........................................26

Assemblage du moteur et de l’arbre...........................27

Montage de la poignée...............................................28

Montage du dispositif de protection............................29

Montage de la lame de coupe ou de la tête

de coupe à fil .............................................................30

Carburant/Ravitaillement............................................31

Manipulation correct de la machine............................32

Mise en marche ....................................................32-33

Ajustement en marche à vide.....................................33

Réaffütage de l'outil de coupe....................................34

Tête de coupe à fil ................................................34-35

Instructions relatives aux réparations ....................35-36

Remisage...................................................................37

SYMBOLES

Vous rencontrerez les symboles suivants en parcourant le manuel d'instructions.

Lire le manuel d'instructions Porter un casque de protection, des

protections visuelles et auditives (pour

la débroussailleuse uniquement)

Etre particulierément soigneux et attentif

Ne pas utiliser de lames métalliques

(Pour la taille bordures uniquement)

Interdit

Vitesse maximale autoriseé de l’outil de

coupe

Maintenir ses distances Mélange de carburant et d'huile

Risque de projections d'objets Démarrage manuel de la machine

Interdit de fumer Arrêt d'urgence

Flammes vives interdites Premier secours

Porter des gants de protection Recyclage

Rejet On/Démarrage

Maintenir toute personne et tout

animal domestique à lécart de la zone

de travail

Off/Arrêt

Porter des protections visuelles et

auditives(pour la taille bordures

d’herbe)

Logo de la CE

Français

La pagina sta caricando ...

Dolmar MS-20C Manuale del proprietario

Dolmar MS-20C Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti