Hach TitraLab AT1000 Series Basic User Manual

DOC022.98.93074

TitraLab

®

AT1000 series

workstations

03/2019, Edition 7

Basic User Manual

Allgemeines Benutzerhandbuch

Manuale di base per l'utente

Manuel d'utilisation de base

Manual básico del usuario

Manual básico do utilizador

Základní uživatelská příručka

Grundlæggende brugervejledning

Basisgebruikershandleiding

Podstawowa instrukcja obsługi

Allmän användarhandbok

Peruskäyttöohje

Основно ръководство за потребителя

Alapvető felhasználói kézikönyv

Manual de utilizare de bază

Temel Kullanıcı Kılavuzu

Základný návod na použitie

Osnovni uporabniški priročnik

Osnovni korisnički priručnik

Βασικό εγχειρίδιο χρήσης

English..............................................................................................................................3

Deutsch.......................................................................................................................... 25

Italiano............................................................................................................................ 48

Français......................................................................................................................... 70

Español.......................................................................................................................... 92

Português.................................................................................................................... 115

Čeština......................................................................................................................... 137

Dansk............................................................................................................................159

Nederlands................................................................................................................. 181

Polski............................................................................................................................ 203

Svenska....................................................................................................................... 225

Suomi............................................................................................................................247

български................................................................................................................... 269

Magyar......................................................................................................................... 292

Română....................................................................................................................... 314

Türkçe...........................................................................................................................336

Slovenský jazyk......................................................................................................... 358

Slovenski..................................................................................................................... 380

Hrvatski........................................................................................................................ 402

Ελληνικά...................................................................................................................... 424

2

Table of contents

Specifications on page 3 Startup on page 18

General information on page 3 Standard operations on page 19

Installation on page 8 Maintenance on page 23

Keypad on page 16

Expanded manual version

For additional information, refer to the expanded version of this manual, which is available on the

manufacturer's website.

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions (W x D x H) 22 x 40 x 36 cm (8.7 x 15.7 x 14.2 in.)

Weight 4 kg (8.8 lb)

Power requirements 100–240 VAC, 50/60 Hz

Altitude 2,000 m (6,562 ft) maximum

Operating temperature 15 to 35 °C (59 to 95 °F)

Relative humidity 20 to 80%, non-condensing

Storage temperature –5 to 40 °C (23 to 104 °F)

Installation category II

Pollution degree 2

Certifications Safety IEC/EN 61010-1; EMC IEC/EN 61326-1

EMC requirements This product is intended to be used in a domestic or

basic electromagnetic environment

Warranty 1 year (EU: 2 years)

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

English

3

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This symbol, if noted on the instrument, references the instruction manual for operation and/or safety

information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and

indicates that care must be taken to prevent damage with the equipment.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

Certification

C A U T I O N

This equipment is not intended for use in residential environments and may not provide adequate protection to

radio reception in such environments.

Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

4

English

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

Product overview

The instrument operates with digital and analog sensors. Measurement applications are installed on

the instrument to automate the measurement process. Instructions show on the display when user

intervention is required.

1 Keypad 6 Beaker 11 Sensor holder

2 Display 7 Syringe protection cover 12 Pump 2 input/output

3 Sensor storage tubes 8 Syringe input/output 13 Pump 1 input/output

4 USB port

1

9 Tube clips 14 Pump access cover

5 Tube holder 10 Syringe

1

A second USB port is found on the rear of the instrument, but the instrument recognizes only

one USB storage device connection at a time.

English 5

Note: Depending on the model, there will be 1 or 2 syringes and syringe input/output ports, and 0, 1 or 2 pumps.

Refer to Table 1.

Table 1 Instrument configurations

Model Syringes Pumps

AT1102 1 0

AT1112 1 1

AT1122 1 2

AT1222 2 2

Instrument connections

Use the USB port on the side of the instrument for the USB applications key supplied with the

instrument. Use the USB port on the rear of the instrument to connect to a printer, mouse, keyboard

or a USB hub.

1 24 V external power supply port 4 External pump port 7 USB port

2 Sensor 1 port 5 External propeller port 8 Ethernet port

3 Sensor 2 port 6 Serial port

Product components

Make sure that all components have been received. Refer to the packing list in the box. If any items

are missing or damaged, contact the manufacturer or a sales representative immediately.

6

English

Figure 1 Contents of the instrument box

Note: For identification, the outlet tube from the syringe is fitted with a blue marker.

1 Instrument 3 Sensor storage tubes (3x) 5 Power cord

2 Tube holder (1 for each syringe

position on the instrument)

4 Power supply

English 7

Figure 2 Contents of the application box

1 Beakers (5 x 50 mL and 5 x 150 mL) 7 Syringe holding ring (1 for each syringe)

2 Tube with anti-diffusion tip (if necessary for the

application)

8 Syringe (refer to Table 1 on page 6 for quantity)

3 Conical adapters (quantity depends on application) 9 USB applications key

4 Magnetic stir bars 10 Glass bottles (not in all application kits)

5 Legacy sensor adapter (not in all application kits) 11 Bottle caps (type and quantity depends on

application)

6 Sensor (type and quantity depends on application)

Installation

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

N O T I C E

This is a class A product. There may be potential difficulties in ensuring electromagnetic compatibility in other

environments, due to conducted as well as radiated disturbances. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate measures.

N O T I C E

Network and access point security is the responsibility of the customer that uses the wireless instrument. The

manufacturer will not be liable for any damages, inclusive however not limited to indirect, special, consequential

or incidental damages, that have been caused by a gap in, or breach of network security.

The instrument is available in different configurations (refer to Table 1 on page 6). This manual

supplies instructions for the installation of an instrument with one syringe and one pump. Adjust the

installation procedure as applicable to accommodate the number of syringes and pumps in the

instrument.

8

English

Installation guidelines

• This instrument is for indoor use only.

• The power supply connector on the rear panel must be easily accessible so the power can be

disconnected quickly in case of emergency.

• Keep the instrument away from temperature extremes, including heaters, direct sunlight and other

heat sources.

• Put the instrument on a stable and level surface in a well ventilated place.

• Make sure that there is at least 15 cm (6 in.) of space on all sides of the instrument to prevent

electrical parts from overheating.

• Do not operate or keep the instrument in dusty, damp or wet locations.

• Always keep the surface of the instrument and all accessories dry and clean.

Connect to AC power

D A N G E R

Electrocution hazard. If this equipment is used outdoors or in potentially wet locations, a Ground Fault

Circuit Interrupt (GFCI/GFI) device must be used for connecting the equipment to its main power

source.

C A U T I O N

Electrical shock and fire hazards. Make sure that the supplied cord and non‐locking plug meet the

applicable country code requirements.

W A R N I N G

Fire hazard. Use only the external power supply that is specified for this instrument.

1. Connect the power cord to the power supply.

2. Connect the power supply to the instrument (refer to Instrument connections on page 6).

3. Connect the power cord to an electrical outlet.

Install the syringe

Before syringe installation, set the instrument power to on. Push the power button on the front of the

instrument. Make sure that the startup sequence shows on the display. The syringe holder lowers to

its operating position.

Note: Ignore any warning messages related to missing applications that show on the display.

The sensor holder has two positions: one over the magnetic stirrer and the second at 180° to the

right. Move the sensor holder away from the instrument to the second position.

Refer to the illustrated steps that follow.

C A U T I O N

In step 6, tighten the syringe using the metallic part at the top. Do not hold the glass section of the syringe. Do not

tighten too much.

To install a second syringe, do steps 5 through 7 again.

English

9

10 English

Install the sensor storage tubes

Put the three sensor storage tubes into the holder that is on the side of the instrument (refer to

Product overview on page 5). Keep the sensor in a storage tube when not in use.

Install the stir bar and the beaker

Add the stir bar to the beaker, and then attach the beaker to the sensor holder.

Prepare the tubes

Remove any bends in the end of the tubes.

Connect the tubes

Arrow symbols identify the inlet and outlet ports for the syringe and the pump connections. The “up”

arrow is the outlet port. The “down” arrow is the inlet port. Turn the tube connectors on the inlet and

outlet ports of the syringe and pump until they click.

English

11

The syringe outlet tube has a blue ring on it. If anti-diffusion tips are necessary, remove the pre-

installed outlet tube from the syringe and install the tube from the application kit with the pre-installed

anti-diffusion tip.

Push the outlet tubes into the tube holder slots so that they are correctly attached.

Install the sensor

Install the legacy adapter

Go to Connect the sensor on page 13 if no legacy adapter is included in the application kit.

1. Connect the measuring, reference and temperature sensors to the legacy adapter.

2. Make sure that the instrument display shows the Home screen. Connect the legacy adapter cable

to a sensor socket on the rear panel of the instrument.

12

English

1 Temperature sensor 2 Reference sensor 3 Measuring sensor

3. The legacy adapter commissioning wizard automatically starts. Follow the instructions that show

on the display. Select the parameter based on the connected sensor.

Option Description

pH Select this parameter if the connected sensor is a pH analogic sensor.

Metal/RedOX/Color Select this parameter if the connected sensor is a Pt-Pt (metallic) analogic sensor or

PTM450/OPT300 sensor.

ISE Select this parameter if the connected sensor is an ion selective sensor.

Refer to the application documentation to enter the related information for the selected

parameter.

Refer to the full user manual for additional information about how to reset the Legacy adapter or

change the sensor name.

Connect the sensor

Use a conical adapter to hold the sensor tightly in the sensor holder.

Connect the sensor to an available sensor port on the rear of the instrument. After the sensor is

connected, make sure that the sensor icon shows in the banner at the top of the display.

N O T I C E

Make sure that the sensor tip is 5 to 10 mm above the top of the magnetic stir bar to prevent any contact with the

bar during operation.

Refer to the illustrated steps that follow.

English

13

Install the titrant and the reagent

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

14 English

N O T I C E

This is only applicable to instruments with two syringes installed.

It is recommended to install the applications (refer to Install the applications on page 18) before installing the

titrant. Applications using titrant from syringe 1 are loaded on line 1 of the home screen (refer to Home screen

on page 17) and applications using titrant from syringe 2 are loaded on line 2. After the applications are

installed, the correct titrant can be connected to the applicable syringe.

Optional: Fill a desiccant cartridge with an applicable desiccant. Put the desiccant cartridge into the

adapter on the titrant bottle cap. Refer to the illustrated steps that follow, step 1.

Loosen the tube connector on the bottle cap. Push the inlet tube through the connector. Make sure

that the end of the tube is at the bottom of the bottle. Tighten the connector on the bottle cap.

Use the same procedure to connect the second titrant bottle if a second syringe is installed on the

instrument.

Refer to the "Application Note" on the USB applications key to identify the correct pump to connect to

the reagent bottle. Refer to the illustrated steps that follow.

English 15

Tidy the work area

Attach the tubes to the instrument with the clips on the electrovalve and the sensor holder. Refer to

the illustrated steps that follow.

User interface and navigation

Keypad

1 Power 3 Selection keys 5 Home key

2 Printer 4 Navigation keys

Key Description

Power Sets the instrument power to on or off. Push the key for 2 seconds to set the power to off.

Printer The printer key only operates if a printer is connected to the instrument. Sends the data

currently shown on the display to a connected printer when pushed. A sound is heard if the

current display cannot be printed. A graph is automatically printed at the end of the

measurement, if the option is selected (Settings > Options).

Selection keys

(contextual)

Used to select options shown above them in the footer bar. The options available are

applicable to the current operation (e.g. calibration, measurement, etc.).

Navigation keys Scrolls through menus and data, enter numbers and letters, enter checkbox settings and set

options for the syringe and the pump.

Home Push this key at any time to go directly to the home screen. A sound is heard if the key is

disabled (e.g. during a calibration or measurement).

16 English

Home screen

1 Available options from this screen 5 Screen name

2 If two syringes are installed, shows applications for

syringe 2

6 Information icons (refer to Table 2)

3 Applications for syringe 1 7 Option available by pushing the selection key below

4 Screen icon 8 Arrow keys available for use in the screen

Table 2 shows the information icons that can be shown in the header bar.

Table 2 Information icons

Icon Description

A printer is connected to the instrument

A USB key is connected to the instrument

A sensor is connected to sensor port 1

A sensor is connected to sensor port 2

The data log file is full. Refer to Manage the data log on page 22 for the options available to manage the

data log file.

A measurement is in operation using the PC software. The keyboard is locked.

English 17

Startup

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Personal injury hazard. Never use the instrument without the syringe cover installed.

Configure the instrument

1. From the main menu, select Settings.

2. Select an option, then push Select.

Option Description

Applications Changes, makes copies, exports and removes application data. Make sure that the

duplication function does not make more than five applications for each syringe installed.

Operators Adds, changes and removes operators.

Date + Time Sets the instrument date and time.

Brightness Sets the brightness of the display.

Sounds Sets the sound options.

Language Sets the language.

Network Give a name to the instrument. This name is used to connect the instrument to a PC. If a

printer is connected, this name is printed on the hard-copy output. Restart the instrument

if the name is changed.

Legacy settings Specify the sensor data when the legacy adapter is used.

Info Shows information about the instrument and the attached hardware.

Restore Defaults Sets the instrument to the default configuration.

Options Sets the application parameters view to expert mode. When the instrument is set to off,

sets the syringe to empty into the titrant bottle. Changes the temperature display unit.

Prints the measurement and derivative curves if a printer is connected. Specify if a

balance is connected. Specify if a propeller stirrer is connected.

Security Change the password and specify which options are password protected.

3. Push Back.

Install the applications

Use the supplied USB key to install the applications. The instrument can install a maximum of five

applications for each syringe installed. For two syringes, the installed applications shown on the top

line of the display refer to syringe one and the installed applications shown on the second line refer to

syringe two.

1. Push Home to go to the main menu.

2. Connect the USB key to the USB port on the side of the instrument. The applications on the USB

key show on the display.

3. Push the arrow keys to highlight and select an application to install. Push the left or right arrow

key to select it. Do this step again to select additional applications to install.

18

English

4. Push Import to install the selected applications.

5. Push OK to complete the installation. The installed applications show on the home screen.

Note: To install more applications, push Home to go to the home screen, then remove the USB key and

reconnect it.

Prepare the instrument for measurement

1. From the home screen, select Purge. All attached devices are listed.

2. Select All elements to purge all the attached devices, or select one device to purge. Push

Select. Air is removed from the device and filled with liquid from the bottle.

3. Push OK when the operation has completed.

4. Make sure that there are no air bubbles in the device. Do step 2 again if there are any air

bubbles.

5. Select the next device to purge if individual devices are being selected.

6. Push Exit when all the tubes are filled with reagent and the device has no air bubbles.

Note: If a few small air bubbles can be seen on the inner wall and/or piston of the syringe, they can be left

without effecting system performance.

Standard operations

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Personal injury hazard. Never use the instrument without the syringe protection cover in place.

C A U T I O N

Chemical exposure hazard. Never remove the stir bar from the beaker before the end of a titration.

Calibration

Calibrate the sensor

1. From the home screen, select Calibration, then push Electrode calibration.

2. If more than one sensor is installed, push the up and down arrow keys to highlight the sensor to

use, then push Select.

3. If more than one application includes calibration parameters for the sensor, push the up and

down arrow keys to highlight the application to use, then push Select. Calibration information

shows on the display.

4. If necessary, select an icon for more information or to change some data.

Option Description

Electrode Shows more information about the sensor.

English 19

Option Description

Operator Changes the operator ID. Select from a list of applicable operators.

Buffer or Standard Shows more information about the buffer set or standard.

5. Do the instructions that show on the display, then push Start to start the calibration. Calibration

data shows on the display.

6. If the default stirring speed needs to be adjusted, push the up and down arrow keys to increase or

decrease the speed.

Note: This adjustment only applies to the current operation. The standard default stirring speed for the

calibration is not changed.

7. Select Stop at any time to stop the calibration. Results are then calculated from the calibration

data available before Stop is selected.

8. For pH sensors only:

Option Description

Yes Continue with the next calibration buffer solution in the sequence.

No Stop the calibration. The calibration can still be validated if at least one buffer calibration was

successful.

9. When the calibration is complete, push the left and right arrow keys to see the different

measurement views.

10. Push Reject or Validate.

Option Description

Reject Select Cancel to go back to the result display or Confirm to reject the calibration and use the

default or previous calibration value.

Validate The calibration is accepted and the new values stored.

Calibrate the titrant

1. From the home screen, select Calibration, then push Titrant calibration.

2. If more than one titrant is installed, push the up and down arrow keys to highlight the titrant to

calibrate, then push Select.

3. If more than one application contains a titrant calibration method, push the up and down arrow

keys to highlight the application to use, then push Select.

4. Calibration information shows on the display. If necessary, select an icon for more information or

to change some data.

Option Description

Information Shows more information about the calibration.

Operator Changes the operator ID. Select from a list of applicable operators.

5. Fill a beaker with the recommended standard amount that shows on the display. If necessary,

add more of the solvent specified in the application note until the sensor is correctly installed in

the sample.

6. Carefully put a magnetic stir bar into the beaker. Make sure there is no liquid spill.

7. Attach the beaker to the sensor holder.

8. Make sure that the icon at the bottom of the display is highlighted. Do the instructions that

show on the display adjacent to this icon. Refer to Connect the sensor on page 13 to make sure

that the tubes and sensor are correctly aligned.

9. Push Start to start the calibration. Calibration data shows on the display.

20

English

La pagina si sta caricando...

Hach TitraLab AT1000 Series Basic User Manual

Questo manuale è adatto anche per

Hach TitraLab AT1000 Series Basic User Manual

in altre lingue

Documenti correlati

Altri documenti