Denon DN-S3500 Manuale del proprietario

TABLE TOP SINGLE CD / MP3 PLAYER

DN-S3500

OPERATING INSTRUCTIONS

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

ISTRUZIONI PER L’USO

INSTRUCCIONES DE OPERACION

GEBRUIKSAANWIJZING

BRUKSANVISNING

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2. Retain Instructions – The safety and operating instructions

should be retained for future reference.

3. Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions

should be followed.

5. Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

6. Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8. Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or

sold with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory

recommended by the

manufacturer.

9. A product and cart

combination should be

moved with care. Quick

stops, excessive force,

and uneven surfaces may

cause the product and cart

combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

11. Power Sources – This product should be operated only

from the type of power source indicated on the marking

label. If you are not sure of the type of power supply to

your home, consult your product dealer or local power

company. For products intended to operate from battery

power, or other sources, refer to the operating instructions.

12. Grounding or Polarization – This product may be equipped

with a polarized alternating-current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

13. Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and

the point where they exit from the product.

15. Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA 70, provides information with regard to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. See Figure A.

16. Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

17. Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

18. Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

19. Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the product.

20. Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

21. Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any way,

and

f) When the product exhibits a distinct change in

performance – this indicates a need for service.

22. Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

23. Safety Check – Upon completion of any service or repairs

to this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

24. Wall or Ceiling Mounting – The product should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

25. Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock to

persons.

IMPORTANT TO SAFETY

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

1. Handle the power supply cord carefully

Do not damage or deform the power supply cord. If

it is damaged or deformed, it may cause electric

shock or malfunction when used. When removing

from wall outlet, be sure to remove by holding the

plug attachment and not by pulling the cord.

2. Do not open the rear cover

In order to prevent electric shock, do not open the

top cover.

If problems occur, contact your DENON DEALER.

3. Do not place anything inside

Do not place metal objects or spill liquid inside the

system.

Electric shock or malfunction may result.

Please, record and retain the Model name and serial

number of your set shown on the rating label.

Model No. DN-S3500

Serial No.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

NOTE:

This CD player uses the semiconductor laser. To allow

you to enjoy music at a stable operation, it is

recommended to use this in a room of 5°C (41°F) ~

35°C (95°F).

LABELS (for U.S.A. model only)

CERTIFICATION

THIS PRODUCT COMPLIES WITH DHHS RULES 21

CFR SUBCHAPTER J APPLICABLE AT DATE OF

MANUFACTURE.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR

REFOR-MANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT BE

ADJUSTED OR REPAIRED BY ANYONE EXCEPT

PROPERLY QUALIFIED SERVICE PERSONNEL.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

This Class B digital apparatus meets all requirements

of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la classe B respecte

toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTERODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE

LA PRISE ET POUSSER JUSQU’ AU FOND.

• FOR CANADA MODEL ONLY

• POUR LES MODELE CANADIENS

UNIQUEMENT

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.

UNDGÅ UDSAETTELSE FOR STRÅLING.

VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ

KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA

ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1

YLITTÄVÄLLE NÄKYMÄMTTÖMÄLLE LASERSÄTEILYLLE.

VARNING– OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA

BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN

UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING SOM

ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

,

CLASS 1

LASER

PRODUCT

,

,,

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product, to which this declaration relates, is in

conformity with the following standards:

EN60065, EN55013, EN55020, EN61000-3-2 and

EN61000-3-3.

Following the provisions of 73/23/EEC, 89/336/EEC

and 93/68/EEC Directive.

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß

dieses Produkt, auf das sich diese Erklärung

bezieht, den folgenden Standards entspricht:

EN60065, EN55013, EN55020, EN61000-3-2 und

EN61000-3-3.

Entspricht den Verordnungen der Direktive

73/23/EEC, 89/336/EEC und 93/68/EEC.

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité

que l’appareil, auquel se réfère cette déclaration,

est conforme aux standards suivants:

EN60065, EN55013, EN55020, EN61000-3-2 et

EN61000-3-3.

D’après les dispositions de la Directive 73/23/EEC,

89/336/EEC et 93/68/EEC.

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo

prodotto, al quale la nostra dichiarazione si riferisce,

è conforme alle seguenti normative:

EN60065, EN55013, EN55020, EN61000-3-2 e

EN61000-3-3.

In conformità con le condizioni delle direttive

73/23/EEC, 89/336/EEC e 93/68/EEC.

QUESTO PRODOTTO E’ CONFORME

AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad

que este producto al que hace referencia esta

declaración, está conforme con los siguientes

estándares:

EN60065, EN55013, EN55020, EN61000-3-2 y

EN61000-3-3.

Siguiendo las provisiones de las Directivas

73/23/EEC, 89/336/EEC y 93/68/EEC.

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid

dat dit produkt, waarop deze verklaring betrekking

heeft, in overeenstemming is met de volgende

normen:

EN60065, EN55013, EN55020, EN61000-3-2 en

EN61000-3-3.

Volgens de bepalingen van de Richtlijnen 73/23/EEC,

89/336/EEC en 93/68/EEC.

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna

produkt, vilken detta intyg avser, uppfyller följande

standarder:

EN60065, EN55013, EN55020, EN61000-3-2 och

EN61000-3-3.

Enligt stadgarna i direktiv 73/23/EEC, 89/336/EEC

och 93/68/EEC.

CAUTION:

•To completely disconnect this product from the

mains, disconnect the plug from the wall socket

outlet.

When setting up this product, make sure that the

AC outlet you are using is easily acceptable.

PRECAUCIÓN:

• Para desconectar completamente este producto

de la alimentación eléctrica, desconecte el

enchufe del enchufe de la pared.

Al ajustar este producto, asegúrese de que la

toma de salida de CA que esté utilizando sea

fácilmente aceptable.

VOORZICHTIGHEID:

• Om de voeding van dit product volledig te

onderbreken moet de stekker uit het stopcontact

worden getrokken.

Let er bij het plaatsen van dit product op dat het

te gebruiken stopcontact goed bereikbaar is.

FÖRSIKTIHETSMÅTT:

• Koppla loss stickproppen från eluttaget för att

helt skilja produkten från nätet.

Vid installationen av produkten ska du se till att

eluttaget den ansluts till är nära utrustningen.

VORSICHT:

• Um dieses Gerät vollständig von der

Stromversorgung abzutrennen, trennen Sie bitte

den Netzstecker von der Wandsteckdose ab.

Stellen Sie bei der Aufstellung dieses Gerätes

sicher, dass die zu verwendende Wechselstrom-

Steckdose leicht zugänglich ist.

PRECAUTION:

• Pour déconnecter complètement ce produit du

courant secteur, débranchez la prise de la prise

murale.

Lors de l’installation de ce produit, assurez-vous

que la prise CA que vous utilisez est compatible.

ATTENZIONE:

• Per scollegare definitivamente questo prodotto

dalla rete di alimentazione elettrica, togliere la

spina dalla relativa presa.

Durante l’installazione, assicurarsi che la presa in

CA utilizzata sia facilmente raggiungibile.

A NOTE ABOUT RECYCLING:

This product’s packaging materials are

recyclable and can be reused. Please

dispose of any materials in accordance

with your local recycling regulations.

When discarding the unit, comply with

your local rules or regulations.

Batteries should never be thrown away or

incinerated but disposed of in accordance with your local

regulations concerning chemical wastes.

ÜBER DAS RECYCLING:

Das Verpackungsmaterial dieses Produktes ist für das

Recycling geeignet und kann wieder verwendet werden.

Bitte entsorgen Sie alle Materialien in Abhängigkeit von

Ihren örtlichen Vorschriften über das Recycling.

Falls das Gerät entsorgt werden muss, beachten Sie die

örtlichen Vorschriften und Gesetze. Die Batterien dürfen

nicht verbrannt und auch nicht in den Hausmüll

geworfen; bitte geben Sie die Batterien gemäß örtlichen

Bestimmungen an den Sammelstellen oder

Sondermüllplätzen ab.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont

recyclables et peuvent être réutilisés. Veuillez disposer

de tout matériau conformément aux réglements de

recylage locaux. Quand l’appareil est mis au rancart,

suivez le règle local ou le loi concernant.

Les piles ne doivent jamais être jetées ou incinérées,

mais mises au rebut conformément aux réglements

locaux concernant les déchets chimiques.

NOTA RELATIVA AL RICICLAGGIO:

I materiali di imballaggio di questo prodotto sono

riutilizzabili e riciclabili. Smaltire i materiali conformemente

alla normative locale sul riciclaggio. Per smaltire l

’

unità,

osservare la normativa in vigore nel luogo di utilizzo.

Non gettare le batterie, né incenerirle, ma smaltirle

conformemente alla normativa locale sui rifiuti chimici.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son

reciclables y se pueden volver a utilizar. Disponga de

estos materiales siguiendo los reglamentos de reciclaje

de su localidad. Cuando se deshaga de la unidad, cumpla

con las reglas o reglamentos locales.Las pilas nunca

deberán tirarse ni incinerarse.

Deberá disponer de ellas siguiendo los reglamentos de

su locali-dad relacionados con los desperdicios químicos.

EEN AANTEKENING WAT BETREFT HET RECYCLEREN:

Het inpakmateriaal van dit product is recycleerbaar en kan

opnieuw gebruikt worden. Er wordt verzocht om zich van

elk afvalmateriaal te ontdoen volgens de plaatselijke

voorschriften. Volg voor het wegdoen van de speler de

voorschriften voor de verwijdering van wit- en bruingoed op.

Batterijen mogen nooit worden weggegooid of verbrand,

maar moeten volgens de plaatselijke voorschriften

betreffende chemisch afval worden verwijderd.

EN KOMMENTAR OM ÅTERVINNING:

Produktens emballage är återvinningsbart och kan

återanvändas. Kassera det enligt lokala

återvinningsbestämmelser. När du kasserar enheten ska

du göra det i överensstämmelse med lokala regler och

bestämmelser.

Batterier får absolut inte kastas i soporna eller brännas.

Kassera dem enligt lokala bestämmelser för kemiskt

avfall.

• Use compact discs that include the mark.

CD’s with special shapes (heart-shaped CD’s, octagonal

CD’s etc.) cannot be played on this set.

Attempting to do so may damage the set. Do not use

such CD’s.

• Benutzen Sie Compact Discs, die das Zeichen

tragen.

Speziell geformte CD’s (herzförmige CDs, achteckige

CDs, usw.) können auf dieser Anlage nicht abgespielt

werden.

Der Versuch derartige CDs abzuspielen kann die Anlage

beschädigen. Verzichten Sie auf die Benutzung solcher

CDs.

• Utiliser des disques compacts portant le logo .

Des CD avec des formes spéciales (CD en forme de

coeur, des CD octogonaux, etc.) ne peuvent pas être lus

sur cet appareil.

Le fait de l’essayer, risque d’endommager le lecteur. Ne

pas utiliser de tels CD.

• Utilizzare compact disc contrassegnati con .

Non è possibile eseguire in questa unità CD con forme

speciali (CD a forma di cuore, ottagonali, ecc.), poiché

possono danneggiare il prodotto. Non utilizzare tali CD.

• Use discos compactos con la marca .

En este equipo no es posible reproducir CDs con formas

especiales (CDs con forma de corazón, CDs octagonales,

etc.).

Si intenta hacerlo, el equipo podrá resultar dañado. No

use este tipo de CDs.

• Gebruik compact discs voorzien van het logo .

CD’s met speciale vormen (bijv. CD’s in de vorm van een

hart, achthoekige CD’s, enz.) kunnen met dit toestel niet

worden afgespeeld.

Wanneer u dit toch probeert, zal u het toestel

beschadigen. Speel dergelijke CD’s dus niet af.

• Använd CD-skivor med -märket.

Specialformade CD-skivor (hjärtformade, åttkantiga, m m)

går inte att spela på den här apparaten.

Utrustningen kan skadas om du försöker göra detta.

Använd inte CD-skivor av denna typ.

Disc

Residue

Rückstand

Résidu

Residuo

Residuos

Oneffenheid

Plastrester

• The disc may not play normally if there is residue

along the edges of the center hole.

• When using new discs in particular, use a pen, etc.,

to remove the residue.

• Die Disk kann nicht normal abgespielt werden, wenn

sich ein Rückstand entlang der Mittellochenden

befindet.

• Insbesondere, wenn Sie neue Disks benutzen, dann

entfernen Sie mit einem Stift, etc. den Rückstand.

• Le disque peut ne pas être lu normalements s’il y a

un résidu le long des bord du trou central.

• Lors de l’utilisation de nouveaux disques en

particulier, utiliser un stylo à bille, etc., pour enlever

le résidu.

• Il disco non viene eseguito in modo corretto se sono

presenti residuo ai bordi del foro centrale.

• Quando si utilizzano dischi nuovi, utilizzare una penna

o uno strumento simile, per rimuovere i residui.

• El disco no puede ser reproducido normalmente

debido a la terminación deficiente de los bordes del

agujero central.

• Para quitar estos residuos de material,

especialmente cuando vaya a re-producir discos

nuevos, utilice un bolígrafo, o algo similar.

• Het is mogelijk dat de disc niet normaal wordt

weergegeven als de randen van het middengat van

de schijf oneffenheden vertonen.

•Verwijder vooral bij gebruik van nieuwe discs de

oneffenheden met een pen of iets dergelijks.

• Det kan uppstå fel vid CD-avspelningen om det finns

plastrester kvar i mitthålet.

• Tänk på att bort dessa med en penna, e d, särskilt

om CD-skivan är ny.

NOTE ON USE / HINWEISE ZUM GEBRAUCH /

OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO

NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA

•Avoid high temperatures.

Allow for sufficient heat dispersion when

installed in a rack.

•Vermeiden Sie hohe Temperaturen.

Beachten Sie, daß eine ausreichend

Luftzirkulation gewährleistet wird, wenn

das Gerät auf ein Regal gestellt wird.

• Eviter des températures élevées

Tenir compte d’une dispersion de chaleur

suffisante lors de l’installation sur une

étagère.

• Evitate di esporre l’unità a temperature alte.

Assicuratevi che ci sia un’adeguata

dispersione del calore quando installate

l’unità in un mobile per componenti audio.

• Evite altas temperaturas

Permite la suficiente dispersión del calor

cuando está instalado en la consola.

•Vermijd hoge temperaturen.

Zorg voor een degelijk hitteafvoer indien het

apparaat op een rek wordt geplaatst.

• Undvik höga temperaturer.

Se till att det finns möjlighet till god

värmeavledning vid montering i ett rack.

• Keep the apparatus free from moisture,

water, and dust.

• Halten Sie das Gerät von Feuchtigkeit,

Wasser und Staub fern.

•Protéger l’appareil contre l’humidité, l’eau

et lapoussière.

•Tenete l’unità lontana dall’umidità,

dall’acqua e dalla polvere.

• Mantenga el equipo libre de humedad, agua

y polvo.

• Laat geen vochtigheid, water of stof in het

apparaat binnendringen.

• Utsätt inte apparaten för fukt, vatten och

damm.

•Do not let foreign objects into the apparatus.

• Keine fremden Gegenstände in das Gerät

kommen lassen.

• Ne pas laisser des objets étrangers dans

l’appareil.

• E’ importante che nessun oggetto è inserito

all’interno dell’unità.

• No deje objetos extraños dentro del equipo.

• Laat geen vreemde voorwerpen in dit

apparaat vallen.

• Se till att främmande föremål inte tränger in

i apparaten.

•Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Gehen Sie vorsichtig mit dem Netzkabel

um.

Halten Sie das Kabel am Stecker, wenn Sie

den Stecker herausziehen.

•Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Manneggiate il filo di alimentazione con

cura.

Agite per la spina quando scollegate il cavo

dalla presa.

•Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el

cordón de energía.

• Hanteer het netsnoer voorzichtig.

Houd het snoer bij de stekker vast wanneer

deze moet worden aan- of losgekoppeld.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas från el-uttaget.

• Unplug the power cord when not using the

apparatus for long periods of time.

•Wenn das Gerät eine längere Zeit nicht

verwendet werden soll, trennen Sie das

Netzkabel vom Netzstecker.

• Débrancher le cordon d’alimentation

lorsque l’appareil n’est pas utilisé pendant

de longues périodes.

• Disinnestate il filo di alimentazione quando

avete l’intenzione di non usare il filo di

alimentazione per un lungo periodo di

tempo.

• Desconecte el cordón de energía cuando no

utilice el equipo por mucho tiempo.

• Neem altijd het netsnoer uit het

stopkontakt wanneer het apparaat

gedurende een lange periode niet wordt

gebruikt.

• Koppla ur nätkabeln om apparaten inte

kommer att användas i lång tid.

• Do not let insecticides, benzene, and

thinner come in contact with the apparatus.

• Lassen Sie das Gerät nicht mit Insektiziden,

Benzin oder Verdünnungsmitteln in

Berührung kommen.

• Ne pas mettre en contact des insecticides,

du benzène et un diluant avec l’appareil.

• Assicuratevvi che l’unità non venga in

contatto con insetticidi, benzolo o solventi.

• No permita el contacto de insecticidas,

gasolina y diluyentes con el equipo.

• Laat geen insektenverdelgende middelen,

benzine of verfverdunner met dit apparaat

in kontakt komen.

• Se till att inte insektsmedel på spraybruk,

bensen och thinner kommer i kontakt med

apparatens hölje.

• Never disassemble or modify the apparatus

in any way.

•Versuchen Sie niemals das Gerät

auseinander zu nehmen oder auf jegliche

Art zu verändern.

• Ne jamais démonter ou modifier l’appareil

d’une manière ou d’une autre.

• Non smontate mai, nè modificate l’unità in

nessun modo.

•Nunca desarme o modifique el equipo de

ninguna manera.

• Nooit dit apparaat demonteren of op andere

wijze modifiëren.

•Ta inte isär apparaten och försök inte bygga

om den.

• Do not obstruct the ventilation holes.

• Die Belüftungsöffnungen dürfen nicht

verdeckt werden.

•Ne pas obstruer les trous d’aération.

• Non coprite i fori di ventilazione.

• No obstruya los orificios de ventilación.

• De ventilatieopeningen mogen niet worden

beblokkeerd.

• Täpp inte till ventilationsöppningarna.

* (For apparatuses with ventilation holes)

CAUTION

• Minimum distances around the apparatus for

sufficient ventilation.

• The ventilation should not be impeded by covering

the ventilation openings with items, such as

newspapers, table-cloths, curtains, etc..

• No naked flame sources, such as lighted candles,

should be placed on the apparatus.

• Attention should be drawn to the environmental

aspects of battery disposal.

• The use of apparatus in tropical and/or moderate

climates.

TOP PANEL DIAGRAM / OBERES BEDIENFELD-SCHEMA / SCHEMA DU PANNEAU SUPERIEUR / SCHEMA PANNEAU SUPERIEUR

DIAGRAMA DEL PANEL SUPERIOR / OVERZICHT VAN BOVENPANEEL / BILD ÖVER ÖVERSTA PANELEN

DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKAENGLISH

P

ARAMETER

P

S

P

US

H

O

N

/O

F

BTRIM

C

L

R

T

.

T

ET

O

E

C

H

O/

L

OOP

FLAN

G

E

R

FI

L

TE

L

R

BRAKE DUMP REVER

SE

PIT

CH

RANGE

K

EY AD

JUST

F

H

RE

V

.

V

PITCH/

V

/

OL

.

CUE

E

J

E

CT

DI

SC

REL

OOP

EXIT

/

M

O

D

E

FILE

S

EAR

CH

BTRIM

B

REL

A

Y

A

CON

T

.

T

!7

!6

@3

#7

$5

$1

$2

$3

$4

!0

o

u i #

8

#8 #

9

#9 $

0

$0 $

6

$6 #

6

#6 #

4

#4 #

1

#1

#2

#5

#3

#0

@9

@8

@7

@6

@5

!4

@1

!8

@0

!9

@4

@2

!1

!2

!5

!3

FRONT PANEL DIAGRAM / VORDERES BEDIENFELD-SCHEMA /

SCHEMA DU PANNEAU AVANT / SCHEMA PANNEAU AVANT / DIAGRAMA DEL PANEL

FRONTAL / OVERZICHT VAN VOORPANEEL / FRONTPANELEN

REAR PANEL DIAGRAM / HINTERES ANSCHLUSSFELD-SCHEMA /

SCHEMA DU PANNEAU ARRIERE / SCHEMA PANNEAU ARRIERE / DIAGRAMA DEL PANEL

POSTERIOR / OVERZICHT VAN ACHTERPANEEL / BAKPANELEN

q

reyt w

POWER ON OFF

DIGITAL OUT

L

R

LINE OUTFADER IN OUT

MEMO

q

r e y t w

• This unit can display text information on the display when

playing CD text discs which contain text information in

English category.

The CD text disc includes the mark shown at the right.

NOTE:

• This unit can provide a text display of the following

types of characters. Other types of characters will

result in “ ” being displayed.

•Alphabet

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Numbers

0123456789

• Symbols

•Bei der Wiedergabe von CD-Textdiscs, die

Funktionstasten in englischer Kategorie enthalten, kann

dieses Gerät auf dem Display Funktionstasten anzeigen.

Die CD-Textdiscs sind mit dem rechts dargestellten Logo

versehen.

HINWEIS:

• Dieses Gerät kann aus den nachfolgend aufgeführten

Zeichenarten bestehende Texte anzeigen. Bei anderen

Zeichenarten wird “ ” angezeigt.

•Alphabet

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Zahlen

0123456789

• Symbole

• Cet appareil peut afficher les textes d’information lors de

la lecture de CD qui comportent ces textes, dans la

catégorie anglaise.

Les CD avec texte se repèrent à la marque indiquée à

droite.

REMARQUE:

• Cet appareil permet l’affichage de textes composés

avec les types de caractère suivants. Tous les autres

types de caractère seront affichés ainsi “ ”.

• Alphabétiques

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Chiffres

0123456789

• Symboles

• Quest’unità può visualizzare dei testi sul display durante

la riproduzione di CD che contengono dei testi in inglese.

Il disco CD con testi include il marchio mostrato qui a

destra.

NOTA:

• Quest’unità è in grado di fornire una visualizzazione dei

testi usando i seguenti tipi di caratteri. Altri tipi di

caratteri causeranno la visualizzazione dell’indicazione

“ ”.

• Alfabeto

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Numeri

0123456789

• Simboli

SPACE

• Esta unidad puede mostrar información de texto en la

pantalla cuando se reproducen discos CD de Texto que

contengan información de texto en la categoría de Inglés.

Los discos CD de Texto incluyen la marca indicada a la

derecha.

NOTA:

• Esta unidad puede mostrar visualizaciones de texto de

los siguientes tipos de caracteres.Otros tipos de

caracteres harán que se visualice “ ”.

• Alfabeto

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Números

0123456789

•Símbolos

• Dit toestel kan tekstinformatie op het display tonen bij

het weergeven van CD-Text discs met tekstinformatie in

de categorie Engels.

Een CD-Text disc is voorzien van het logo rechts.

OPMERKING:

•Dit toestel kan de volgende tekens als tekst

weergeven. Voor andere types van tekens verschijnt

“ ” op het display.

•Alfabet

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Getallen

0123456789

• Symbolen

• Denna apparat kan visa text på displayen när du spelar

CD-textskivor innehållande information på engelska.

CD text-skivor bär märket som anges på höger sida.

OBSERVERA:

• Apparaten kan visa text med följande teckentyper. För

övriga tecken kommer “ ” att visas.

• Alfabetiska

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

• Siffror

0123456789

• Symboler

SPACE

1

ENGLISH

– TABLE OF CONTENTS –

z Main features .....................................................1

x Installing the platter, the scratch disc and the

slipmat / Connections.........................................2

c Part names and functions ............................3 ~ 5

v Compact discs....................................................6

b Basic operation...............................................6, 7

n Next Track...........................................................8

m Scratch................................................................9

, Seamless loop/Hot start/Stutter...................9, 10

. B trim................................................................10

⁄0 Sampler ............................................................11

⁄1 Auto BPM Counter/Effector .......................12, 13

⁄2 MP3 playback .............................................13, 14

⁄3 Platter effect.....................................................15

⁄4 Memo (Custom setting memory).....................16

⁄5 Preset ...............................................................17

⁄6 Specifications ...................................................18

• ACCESSORIES

Check that the following parts are included in addition to the main unit:

q Operating instructions ........................................1

w Connection cords for signal output (RCA) ..........1

e Aluminum platter ................................................1

r Slip Mat...............................................................1

t Scratch disc ........................................................1

1

MAIN FEATURES

Congratulations on your new purchase of the DN-

S3500. The DN-S3500 table top single CD/MP3 player

is equipped with a variety of advanced features,

functions and rich performance for unlimited

creativeness and showmanship.

Professional Structure and parts

1. Active Motor Platter

When playback is started, the Platter turns, feels

and reacts in the same way as with an analog

turntable.

The active Platter consists of the Motor-driven

Platter, Slip Mat and Scratch Disc just like an analog

turntable for true vinyl emulation. Beats can be

matched and scratching or cueing can be performed

with the same feeling as an analog turntable.

2. High Torque Direct Drive Motor

Denon’s all new in-house design Direct Drive

Motor with brushless construction delivers a

powerful start-up torque of 2.5 kg-cm, enabling

the platter to instantly reach full rotation speed

within 0.5 sec.

3. 33/45 R.P.M

You can adjust the platter speed to spin at 33 or

45 rpm, depending on your preference.

Features and Functions

With the implementation of a powerful DSP and large

memory capacity allows for many new controlling

features such as:

1. SCRATCH

Thanks to the active Platter and Scratch Disc, the

Scratch sound is comparable to analog turntables.

Furthermore, the Main Track and Samples can be

selected as the Scratch sound source at the touch

of a button.

2. MP3 PLAY BACK

It is possible to play MP3 and view files created in

the specified format found on page 13.

Files can be searched for easily either manually, or

by scanning or using a number of file search

functions (File search, File/Folder search, Artist

name search, Title name search, File name

search).

3. NEXT TRACK RESERVE

The next track can be selected while continuing to

play the current track for a seamless transition.

4. CROSS FADE

In conjunction with the Next Track feature, the

DN-S3500 can perform a smooth internal cross

fade when transitioning to the new track.

5. HOT START and STUTTER

The Hot Start function lets you start playback

immediately from a set point decided by you. Up

to two points can be set using the A1 and A2

buttons. The loaded Hot Starts can also be used

to “Stutter” those same points. When in Stutter

mode, momentary audio is triggered according to

the length of time of which these buttons are held

down and released.

6. SEAMLESS LOOP

With this function, any section on a disc can be

played repeatedly between A & B points with no

break in sound or limit in length. The DN-S3500

has a variety of looping options such as Exit,

Reloop and dual looping.

7. SAMPLER

On-board digital Sampler can record up to 15

seconds CD quality sound at 44.1kHz sampling

frequency. You can seamlessly loop this sample or

play it backwards (REVERSE). The pitch and

output level of a sample can be adjusted

independently.

The B point can be easily set or changed exactly

the same way as you would use with the A-B

Seamless Loop function.

The CD Seamless loop can be easily copied to

Sampler. This adds a whole new level of

CD/Sample remixing.

8. B TRIM

The B points for the Seamless Loop and the

Sampler can easily be adjusted using the Scratch

Disc. Adjustments can be made in real-time while

playing the live loop.

9. AUTO BPM COUNTER, BPM LOCK, MANUAL

TAP, and MANUAL BPM INPUT

In addition to the Auto BPM counter and Manual

Tap function, the DN-S3500 is also equipped with

a Lock function for temporarily locking the Auto

BPM counter. A Manual BPM Input function is

available too for inputting the known BPM value

directly by a Rotary knob, so the BPM setting can

be made easily.

10. ON BOARD EFFECT’S

Seven types of effectors are included.

ECHO/LOOP:

The ECHO and LOOP functions can be

selected. Looping for the feedback time (ECHO

LOOP) is possible by setting the feedback

number to “MAX”.

FLANGER:

The feedback time and feedback gain can be

selected.

FILTER:

One of three filters (LOW PASS, MID PASS and

HIGH PASS) can be selected and Individually

adjusted.

11. PLATTER MODE

Analog turntable-like playback can be simulated

using three Platter effects.

BRAKE:

Simulates a winding-down sound of a turntable

coming to a full stop slowly. (Slowing-down

time can be adjusted.)

DUMP:

Plays the sound backwards while continuing in

a forward motion without losing “elapse time”

when you return back to normal play.

REVERSE:

(Reverse) Plays the sound and spins the platter

backwards until you return to normal play.

12. MEMO (CD & MP3)

Various settings such as Cue Point, Hot Start, A-B

Loop, BPM, Pitch and Key Adjust can be saved to

the internal non-volatile memory for later recall.

Up to 5000 points are available.

In Addtion, memo data can be transferred into the

DN-S3500 from an another DN-S3500, DN-S5000,

DN-S3000 or DN-D9000.

13. PITCH/KEY ADJUST

PITCH:

Playback speed is adjusted with PITCH slider.

Adjustable pitch ranges are +/– 4, 10, 16, 24,

50, 100% (selectable live).

KEY ADJUST:

Keeps the original key even if the pitch playing

speed is changed with the PITCH slider.

14. DIGITAL OUT

The digital output for Main provides a true 100%

digital signal without any restrictions or limitations

regardless of pitch change or mode setting.

15. FADER START

The DN-S3500 FADER START controls are compatible

with our mixers and most other brand mixers.

16. SHOCKPROOF MEMORY

20 seconds of shock-proof memory guards

against audible interruptions due to external

mechanical shocks such as bumps or other hard

vibrations, which is especially helpful for the

mobile DJ as well as for nightclub-installed

applications.

17. PRESETS

It is possible to customise the machine to your

preference by saving your favourite setting to

internal memory. For items found in the presets,

please see page 17.

18. CD TEXT

19. CD-R/RW Play Back

This player can play CD-R/RW discs, but only if

they are finalized. Note however that depending

on the recording quality, the player may not be

able to play some finalized CD-R/RW discs.

20. Power on Play

The player can be set so that playback in the relay

mode starts when the power is turned on.

21. Plug Ins

From time to time, we will add new exciting

features or improve upon the current ones by free

firmware Plug Ins.

Please visit to www

.denondj.com ensure you

have the latest firmware version.

y Adaptor unit ........................................................1

• Scratch Disc adaptor (Adaptor (1)) ...................2

• 7”record adaptor (Adaptor (2)) .........................1

•Fixing Plate.......................................................1

• Screw (< head) ................................................3

2

ENGLISH

2

INSTALLING THE PLATTER, THE SCRATCH DISC AND

THE SLIPMAT / CONNECTIONS

(2) CONNECTIONS

1. Turn off the POWER switch.

2. Connect the RCA pin cords between the DN-S3500 outputs and inputs of your mixer.

3. If your mixer has Fader Start function such as our DENON Mixer, connect FADER jack to the mixer using 3.5

mm stereo mini cord.

POWER ON OFF

DIGITAL OUT

L

R

LINE OUTFADER IN OUT

MEMO

L

R

L

R

L

LINE1

FADER

PGM 1

FADER

LINE

OUT

(3) INSTALLATION

Please set up DN-S3500 horizontally.

(4) INSTALLING THE 7” (17cm) RECORD ADAPTOR

Your own 7” (17cm) vinyl record can be installed on this product by using the provided adaptor.

This original design grants you the freedom to use your favorite vinyl record for that ultimate analog turntable

feel.

*Make sure the record used is flat and not warped.

• 7” (17cm) record adaptor accessories

q Adaptor (2)........................................................1

w Screw (< head) ................................................3

e Fixing Plate .......................................................1

DN-X300

(1) INSTALLING THE PLATTER, THE SCRATCH DISC and THE SLIPMAT

• Accessories

1. Install the Platter on the taper boss of the motor.

2. Install the Slip Mat on the Platter.

3. Insert D hole of the Scratch Disc on the D shaft of

the Motor.

NOTE: The printed face is located on the Slip Mat

side.

4. Insert the Adaptor according to the direction of the

arrow.

NOTE: Please note the direction of insertion.

NOTE:

Depending on the RECORD you choose, friction

with the Slipmat may not be enough, which can

cause an undesired drag sound.

If so, use a different record that’s thicker or

heavier.

1. Set Adaptor (2) in the hole of 7” record.

2. Fix Plate with 3 screws. (< head).

3. Insert D hole of the Adaptor (2) on the D shaft of the

Motor.

4. Insert the Adaptor (1) on the Adaptor (2).

q Aluminum Platter..............................................1

w Scratch Disc......................................................1

e Slip Mat ............................................................1

r Adaptor (1)........................................................2

(One is for spare parts.)

Scratch Disc

(Groove side

DOWN)

D shaft

Slip Mat

Platter

Taper Boss

(Motor Unit)

Fig. 1

Scratch Disc

Adaptor (1)

Fig. 2

Fig. 3

Screw (< head)

Fixing Plate

7” (17 cm) record

Adaptor (2)

Fig. 1

Fig. 2

7” (17cm) Disc

Adaptor (2)

Adaptor (1)

Slip Mat

Adaptor (1)

CAUTIONS:

• Do not touch the motor unit.

• Do not turn on the power without Platter.

NOTE:

Please note the fall of Platter when you move DN-

S3500 after Platter is set.

3

ENGLISH

u PLAY/PAUSE button (13)

• This button will start or pause playback.

• Push once to start playback, once again to

pause playback, and once more to resume

playback.

i DISC EJECT button

• Push this button to eject the disc.

• The disc will not eject during playback.

Stop playback before pushing this button.

o CUE button

• Pushing this button in play mode will force the

track back to the position which playback

started. While in search mode, it makes new

Cue point. (Cue)

• In Cue mode, by pushing the CUE button makes

a Stutter sound from the Cue point. This is

called Stutter play. (Stutter)

!0 Platter/Scratch Disc

Use this vinyl scratch disc for manual search,

Pitch Bend and Scratch operations.

• Platter:

The Platter spins when playback of the source

select Scratch mode button is in the Main or

Sampler position and in play mode.

• Scratch Disc:

When the Scratch Disc is turning, Scratch

playback of the source selected (Main or

Sampler) starts.

NOTE:

The Platter does not spin when the Scratch

mode is set to the BEND/SEARCH mode.

(3) Top panel

CAUTION:

• Note that there are many buttons working two

different function selected by short time pushing

or long pushing (1 second or more). The mark

indicates short time push function and mark

indicates long time push function.

@0 (SAMP) STOP button

• Push this button while in Sampler record or

playback, Sampler to stop recording or playback.

• When the Sampler is in the stop status, the

STOP button can be used for Stutter playback.

@1

(SAMP) PITCH/VOL., B TRIM button

• PITCH/VOL.:

When this button is pressed, the SAMPLER

PITCH is selected. When pressed again, the

SAMPLER LEVEL is selected.

Pitch of Sampler and output level of Sampler

playback can be adjusted with the

PARAMETERS knob.

• B TRIM:

When this button is pressd for more than 0.5

sec, the Sampler B TRIM mode is selected.

@2 TITLE/ID3 button

• CD TEXT:

When there is CD text data, the CD text data is

displayed automatically or when the TITLE

button is pressed.

If no TEXT is available, the display will indicate

“No TEXT”.

• MP3:

When an MP3 file has ID-3 tag data, the title,

artist name and album name are selected and

displayed each time the TITLE button is

pressed.

@3 TIME, T.TIME button

• TIME:

A short push will display mode changes

between ELAPSED TIME and REMAIN TIME.

• T.TIME:

A long push, will display mode changes between

TRACK TIME and DISC TIME. (for CDDA)

• So, you can select display mode from four

modes, TRACK ELAPSED, TRACK REMAIN,

DISC ELAPSED and DISC REMAIN.

@4 MEMO, PRESET button

• MEMO:

The memo mode starts when this button is

pushed once, while in the Cue mode.

• PRESET:

When this button is pushed for more than 1 sec,

the PRESET mode menu is displayed.

The machine status must be in, CUE, PAUSE or

No Disc mode before entering the preset mode.

3

PART NAMES AND FUNCTIONS

(1) Front panel

q Disc loading slot

• Load the disc slowly, and release it once the

DN-S3500 starts grabbing the disc in.

NOTE:

Please clean the dirt of the label side of a disc

and start loading of the disc.

Dirty discs can cause the loading rollers to slip

upon insertion.

CAUTIONS:

• Do not load discs when the power is turned

off.

• Do not try to forcibly remove a disc once the

DN-S3500 has started to grab the disc.

• Do not load more than once disc at a time or

insert anything other than discs.

Otherwise the loading mechanism may be

damaged.

w POWER button (¢ON £OFF)

• Push this button to turn power on and off.

(2) Rear panel

CAUTION:

• Do not turn off the power while a disc is

loading or being ejected. Otherwise the

loading mechanism may be damaged.

e Analog output jacks

(LINE OUT)

• This is unbalanced RCA output jacks.

• Audio signals outputs.

r Fader start jack

• Use this when your mixer has the Fader Start

function.

t Digital output jack

• Digital data is available from this jack.

•Use 75 Ω/ohms pin cord for connection.

•We recommend you use braided wire type

shielded cable.

NOTE:

The playback level after analog conversion is set

to –6dB below the usual level to avoid digital

distortion.

y Memo jack (MEMO IN/OUT)

• Use this when you transfer the Memo data from

an another DN-S3500, DN-S3000, DN-S5000 or

DN-D9000.

!1 FLIP/CLR button

• FLIP:

Use this to select operating mode of A1 and A2

buttons, from Hot Start mode and Stutter mode.

The display will indicate “H/S” or “STR”.

• A1, A2 CLR:

If the A1 or A2 button is pushed while pushing

the FLIP button, you can clear the selected A

point.

By holding down just the FLIP button for more

than 1 sec, you can clear A1 and A2 points all at

once.

!2 A1, A2 button

• Using this button you can create a starting point

for Hot Start, Seamless Loop and Stutter.

!3 B button

• Use this to set the B point to create a Seamless

Loop after the A point has been set.

!4 EXIT/RELOOP button

• Use this to exit or return back again to the

Seamless loop playback. You can add variety to

looping with this function.

!5 B TRIM button

•When the button is pressed during playback,

the *B TRIM MODE is selected. *Only when a

seamless LOOP is set.

In the standby and pause modes, only the B

TRIM MODE can be selected.

!6 (SAMP) REV/CLR button

• (SAMP) REV:

Use this to select the sample play direction

forward and reverse. When select reverse REV

LED lights up.

• (SAMP) CLR:

If the SAMP button is pushed while pushing the

SAMP REV button, you can clear the SAMP

data.

Or, by holding down just the SAMP REV button

for more than 1 sec.

!7 SAMP button

• Push this button to record or play the Sampler

sound.

!8 (SAMP) B button

• Use this to set the Sampler loop B point.

!9 (SAMP) EXIT/RELOOP

• Use this to turn the Sampler Loop mode on and

off. Also acts as EXIT/RELOOP button for

Sampler Loop to exit or reloop.

CAUTIONS:

• Do not forcibly try to stop the Platter when it

is turning. Otherwise the moving Platter

mechanism may be damaged.

• If a problem with Platter rotation arises

when the Platter is turning, the Platter stops

turning and the pause mode is set.

4

ENGLISH

#1 PITCH BEND – button

#2 PITCH BEND + button

• Pushing these buttons will change main playing

speed temporarily.

•While pushing PITCH BEND + button, the

playing speed increases and speed decreases

while pushing PITCH BEND – button.

• When these buttons are release, the playing

speed returns to the previous speed.

#3 Pitch Slider

• Use this slider to adjust playing speed faster or

slower.

#4 PITCH, RANGE button

• Push this button to set the PITCH mode on and

off.

• RANGE:

Push this button for more than 1 sec to select

the pitch range. The pitch range can be selected

with the PARAMETERS knob from ±4, 10, 16,

24, 50 or 100%.

#5 KEY ADJUST button

• Push this button to set the KEY ADJUST mode

on and off.

#6 PLATTER SOURCE button

Select the source for Scratch playback and the

manual search/bend mode.

• MAIN:

This button lights up orange.

Manipulate the Main Track sound.

• SAMP.:

This button lights up green only if a sample is

loaded.

Manipulate the Sampler sound via the scratch

disc.

• BEND/SEARCH:

When this button is pushed again, the

BEND/SEARCH mode is selected.

When the Scratch Disc selector is set to

BEND/SEARCH during playback, it works as the

pitch bend function by turning the scratch disc.

When Scratch Disc is turned in the pause or

standby mode, it functions as the manual

search function. In Manual search, you can

move the CUE point around by one frame at a

time (1/75 second) with an audible frame-repeat

sound, da-da-da-da.

@5 CONT./SINGLE, RELAY button

• CONT./SINGLE:

A short tap of this button will toggle between 3

possible END modes for playback.

CONT. (continue: plays all tracks) SINGLE (stops

playing and ReCUE’s back to your original set

point), PLAYLOCK-see below.

• SINGLE PLAY LOCK:

SINGLE PLAY LOCK can be selected by

PRESET. When SINGLE PLAY LOCK is selected,

track selection during playback is disabled. This

prevents playback from stopping when the

Track Select Knob is turned accidentally during

playback. Play ending mode is the same as

single.

• RELAY:

You can turn on and off RELAY PLAY mode.

Relay playback is possible when two DN-

S3500s are connected by the MEMO in/out

jacks.

@6 FILE SEARCH MODE button

• MP3 DISC only:

When pushing this knob the file search

selection mode can be selected with the

PARAMETERS knob.

@7 TRACK/PARAMETERS knob

• TRACK:

When PARAMETERS LED is on, turn this knob

to select tracks.

By pushing this knob down while turning, the

tracks will change by 10 tracks at a time.

• PARAMETERS:

When the PARAMETER LED is flashing, turn

this knob to select and change the parameter

for items found in the Platter effects, Memo,

and Preset data, etc.

@8 NEXT TRACK button

•

If this button is pushed during playback, the NEXT

TRACK mode will be selected. The next track can

be selected with the PARAMETERS knob.

@9 FAST SEARCH (6)

QUICK JUMP button

#0 FAST SEARCH (7)

QUICK JUMP button

• QUICK JUMP:

When one of these buttons is tapped shortly,

the playback position jumps approximately 10

seconds in the forward (

7) or reverse (6)

direction. The jump time can be changed in the

preset mode.

• FAST SEARCH:

When one of these buttons is pressed and held

in, the disc is fast-searched in the forward (

7)

or reverse (

6) direction.

#7 SCRATCH direction select lever

Select the Scratch play direction.

• BOTH:

When the Scratch Disc is turned, the Scratch

sound is heard in both stroke directions.

• FWD:

When the Scratch Disc is turned, the Scratch

sound is heard in the forward direction only.

#8 BRAKE button

• Push this button to set the BRAKE.

#9 DUMP button

• Push this button to set the DUMP.

$0 REVERSE button

• Push this button to set the REVERSE.

$1 TAP, LOCK, AUTO, INPUT BPM

button

• TAP:

When you push this button repeatedly, the Auto

mode turns off and starts measuring your Beats

Per Minute (BPM) by tapping.

• LOCK:

When this button is pressed once while the

auto BPM counter is operating, the data

measured by the auto BPM counter is locked.

• AUTO:

When pushing the TAP button for 1 second,

activates AUTO BPM mode.

The measured BPM is displayed in the character

section of the display.

• INPUT BPM:

When the TAP button is pressed and held in for

more than 2 seconds, the BPM input mode is

set and the BPM value can be input directly with

the EFFECTS knob. When the tap button is

pressed again, the BPM input mode is turned

off and set.

NOTE:

If you select a new track, AUTO BPM mode

turns on automatically.

$2 ECHO/LOOP button

• The ECHO and ECHO LOOP functions can be

selected. The feedback time and feedback ratio

can be selected. Looping for the feedback time

(ECHO LOOP) is possible by setting the

feedback number to “MAX”.

$3 FLANGER button

• The feedback time and feedback gain can be

selected.

$4 FILTER button

• One of three filters (LOW PASS, MID PASS and

HIGH PASS) can be selected.

$5 EFFECTS knob

• Use this knob to set parameters of the internal

effector.

$6 PLATTER LED

• This vibrant blue bar provides platter modes at a

glance such as, Scratch Memory, Pitch Bend,

Frame Search and Loaded Disc.

5

ENGLISH

q Track, minute, second and frame

displays

• These displays indicate current position

information.

w Time mode indicators

• When the TIME button is pushed, the Time

mode indicator switches as follows:

ELAPSED:

Track’s elapsed time is displayed.

REMAIN:

Track’s remaining time is displayed.

T. ELAPSED:

The total elapsed time of disc is displayed.

T. REMAIN:

The total remaining time of disc is displayed.

e Play mode indicators

• When SINGLE indicator lights up, playback will

finish at end of current track.

• When CONT. indicator lights up, playback

continues until the end of the disc.

r BPM indicator

• Lights up when the BPM is displayed on the

pitch display.

t MP3 indicator

• Lights up when an MP3 disc is detected.

y Loop mode indicators

• DN-S3500 has Loop mode indicators which

consist of A , B and two arrows. A and B marks

indicate A and B points have been set.

•Two arrows indicate loop setting mode as

follows.

or Left arrow only on:

Hot Start mode

Both arrows on:

Seamless Loop mode

, Both arrows flashing:

Seamless Loop Playing

, Left arrow on, right flashing:

Exit play from Seamless Loop

u MP3 file search mode indicators

FILE:

FILE indicator appears in the display, when in

the FILE name search mode.

FOLDER:

FOLDER indicator appears in the display,

when in the FILE & FOLDER name search

mode.

TITLE:

TITLE indicator appears in the display, when

in the TITLE name search mode.

ARTIST:

ARTIST indicator appears in the display, when

in the ARTIST name search mode.

q w e r

!2

!1

y

!

0

iu

t

o

y

(4) Display

i Character display

•You can select the mode or function using

PARAMETERS knob following the short

message which is displayed on the character

display area.

• The character display indicates the operation,

mode name, data, etc., and displays such guide

messages as “Push/Play” means if “YES”,

push PARAMETERS knob. The display indicates

and marks sometime, note that

mark says you to turn PARAMETERS knob and

marks says to push PARAMETERS knob.

• The PARAMETERS LED flashes when you can

use PARAMETER knob, otherwise this knob

used for Track Selection.

o Play Position indicators

• Play position indicator:

The 30 dots indicate a visual track position

marker during normal play. The 10 Orange dots

indicate the play position during the reverse play

mode.

• End of Message:

When the time remaining to the end of the track

is less than the specified time, the EOM (End Of

Message) play position indicator flashes along

with the remaining time, notifying of the track

end.

✽The EOM time can be set in the presets.

!0 KEY ADJ. indicator

• KEY ADJ. indicator appears in the display when

the Key Adjust mode is ON.

!1 MEMO indicator

• MEMO indicator appears in the display when

there is a memo setting found for the current

playing track or the track at which the Cue

standby mode is currently set.

!2 Pitch display

• This indicator display the playback speed (pitch).

6

ENGLISH

5

BASIC OPERATION

Play and pause

•When the o CUE button is pushed during playback,

the track stops and returns to the original position of

which playback started from, the (Cue point). This

function is also called Back-Cue. With the Back-Cue

function, you can start from exactly same position.

The o CUE button illuminates solid red when DN-

S3500 is ready to start playback.

•You can set and change Cue point as follows.

• When you started playback.

•Track select finished.

• manual search.

Play and Cue

•

If you would like to start playback other from the

beginning of the track, you can move the Cue Point

using fast Search or the manual frame search function.

4

After you have found your

preferred Cue point, push

the o CUE button then a

new Cue point is set.

2

3

Turn the !0 Scratch Disc to

change Cue point. You can hear

the short sound of the current

Cue point.

CUE

•Turn the @7 TRACK knob.

• By pushing @7 TRACK knob down while turning, the

tracks will increment 10 at a time.

Select the track

Move the Cue point

1

You can move to the approximate playback

start position by @9 or #0 FAST SEARCH

buttons.

QUICK JUMP

• If the FAST SEARCH button is

tapped shortly, the playback

position jumps about 10

seconds.

The jump time can be selected in the preset

mode from 10, 20, 30 or 60 sec.

FAST SEARCH

• When the FAST SEARCH button is pressed

and held in, the disc is fast-searched.

QUICK JUMP

FAST SEARCH

•

Each push of the u PLAY/PAUSE (13) button

switches between playback and pause. PLAY/PAUSE

(

13) button illuminates solid green during playback

and flashs in pause.

•When the u PLAY/PAUSE (13) button is pushed

during play, the DN-S3500 pauses playback at that

point. Push u PLAY/PAUSE (

13) button once again

and playback resumes.

• When the Platter mode is set to MAIN, the Platter

turns when the Main Track is played. When the

rotation of the Scratch Disc is stopped by your hand,

the sound pauses, and when your hand is released

playback resumes.

When the !0 Scratch Disc is turned in the

pause, Cue or frame repeat mode, it works as

the manual frame search function.

Push the #6 PLATTER SOURCE

button to set !0 Scratch Disc to

search mode. The PLATTER

SOURCE button LEDs will turn

off and the display will indicate

“FRAME Search”.

SOURCE

4

COMPACT DISCS

1. Precautions on handling compact discs

• Do not allow fingerprints, oil or dust to get on the surface of the disc.

If the disc is dirty, wipe it off with a soft dry cloth.

• Do not use benzene, thinner, water, record spray, electrostatic-proof chemicals, or silicone-treated cloths to

clean discs.

•

Always handle discs carefully to prevent damaging the surface; in particular when removing a disc from its

case or returning it.

• Do not bend the disc.

• Do not apply heat.

•Do not enlarge the hole in the center of the disc.

• Do not write on the label (printed side) with a hard-tipped implement such as a pencil or ball point pen.

• Condensation will form if a disc is brought into a warm area from a colder one, such as outdoors in winter.

Do not attempt to dry the disc with a hair dryer, etc.

2. Precautions on storage

• After playing a disc, always unload it from the player.

• Always store the disc in the jewel case to protect from dirt or damage.

• Do not place discs in the following areas:

(1) Areas exposed to direct sunlight for a considerable time.

(2) Areas subject to accumulation of dust or high humidity.

(3) Areas affected by heat from indoor heaters, etc.

7

ENGLISH

Power on play

• When “POWER ON PLAY” is set to “ON” at “⁄5

PRESET (10)”, playback starts from the first track on

the disc when the power is turned on.

Relay playback

• Relay Play function is a useful mode to continue

playback between two DN-S3500s.

•Connect the MEMO IN/OUT terminals between two

DN-S3500s.

1

Start Relay Play

q Push the RELAY

button for more than

1 sec to enable

Relay play mode.

You can set Relay

play mode as below.

• In the single play mode, when the one

player’s playback reaches end of track,

another DN-S3500 starts playing.

• In the continuous play mode, when all

tracks on one player are finished, another

DN-S3500 starts.

• The discs in two DN-S3500s can be

played alternately by setting both DN-

S3500 to the relay play mode.

/SINGLE

RELAY

CONT.

2

Stop Relay Play

w When the RELAY

button is pushed for

more than 1 sec

while in the relay

play mode, the relay

play mode is turned

off.

/SINGLE

RELAY

CONT.

P

ARAMETER

P

S

P

US

H

O

N

/O

F

REL

OOP

EXIT

/

M

O

D

E

FILE

S

EAR

CH

BTRIM

A2

B

RE

CON

T

.

T

q, w

2

0

Move the #3 Pitch Slider to adjust

the pitch. The current pitch setting

is displayed on the display.

Pitch decreases

Pitch increases

3

DN-S3500 has six pitch ranges, 4%, 10%,

16%, 24%, 50% and 100%.

When the #4 RANGE button

is pushed for more than 1 sec,

the pitch range can be selected

with the @7 PARAMETERS knob.

•When the @7 PARAMETERS knob is pushed

the pitch range is entered and the pitch range

selection mode is cancelled.

NOTE:

Only a max of 16% range for MP3 discs.

•With PITCH BEND function you can change pitch

temporary. DN-S3500 has two ways for this function

PITCH BEND buttons and Scratch Disc.

Pitch Bend

PITCH

RANGE

TRACK SEARCH

PARAMETERS

PUSH ON/OFF

1

3

PITCH BEND +/– buttons

• Push the #1 PITCH BEND – or #2 + button for

momentary change of pitch.

While holding these

buttons down, the pitch

continues to change up

to the limitation.

• After releasing the

PITCH BEND buttons,

playback pitch returns to slider setting.

Scratch Disc

•

When the Platter source is

set to BEND, the playback

speed can be changed by

turning !0 Scratch Disc during

playback. The display will

indicate “Pitch Bend” during this mode.

• The pitch increases gradually when the

Scratch Disc is turned clockwise and

decreases when turned counterclockwise.

• When you stop turning the Scratch Disc, the

playing speed returns to the previous pitch.

PITCH BEND

2

When the Platter source is set

to MAIN and the Platter is

turning, playback of the Main

source can be slowed

temporarily by lightly pressing

!0 Scratch Disc or PLATTER.

In addition, playback can be quickened

temporarily by pushing Scratch Disc or

PLATTER in the direction in which the Platter is

turning.

1

Push the #4 PITCH button to

PITCH LED lights up.

PITCH

RANGE

•With the Pitch slider you can adjust the playback

speed (Pitch).

• If you would not prefer to change key of sound, use

the Key Adjust function.

Adjusting the pitch and Key Adjust

4-1

KEY ADJUST ON

When the #5 KEY ADJUST button is pushed,

the Key Adjust function is turned on and lights

up “KEY ADJ.” in the display.

4-2

KEY ADJUST OFF

When the #5 KEY ADJUST button is pushed

again, the Key Adjust function is turned off.

8

ENGLISH

3

Track search start

r

When the CUE button is

pushed after selecting

the track, current

playback continues as

the next track is

searched for and the

standby mode is set.

When the standby

mode is set, the CUE button lights up and

the PLAY/PAUSE button flashes.

•

During this time, if a loop of 6 seconds or

less is actively looping, it will continue to

loop until PLAY is ultimately pressed.

If a loop is over 6 sec, you must first EXIT

from the loop in order to enter Next Tr

mode.

• The time display indicates the remaining

playback time for data in the memory

after CUE is pressed.

NOTE:

The amount of time for which playback of

the currently continuing track can be

continued is a maximum of 10 seconds

from the time searching for the next track

starts.

CUE

4

5

Next Track cross fade

✽The currently playing track can be faded

out when starting to play a different track.

The fade out time can be selected at

⁄5

PRESET “(3) Next Track”.

• If the PLAY/PAUSE button is not pushed

after standing by at the next track,

playback of the next track starts once all

of the currently playing playback data has

been played.

Next Track playback start

t

When the PLAY/PAUSE

button is pushed, the

current playback is

stopped and playback

of the next track starts.

6

NEXT TRACK

• It’s now possible to select the beginning of the next track to be played while continuing playback of the current

track without interrupting playback.

*Crossfade can also be used for a smooth transition.

1

2-1

Enter Next Track mode

q When the NEXT TRACK

button is pushed during

playback, the NEXT TRACK

function is turned on.

• When this mode is set,

CUE button blink.

• When the button is pushed again, the

NEXT TRACK mode is turned off.

Select the track

w Turn the PARAMETERS knob and select for

the next track to be played.

NEXT TRACK

TRACK SEARCH

PARAMETERS

PUSH ON/OFF

2-2

Select the MEMO

(Next track Memo function)

e The CUE point of MEMO can be selected

as the NEXT TRACK start point.

• When the NEXT TRACK happens to be

one where a MEMO has been previously

memorized, the MEMO indicator lights

up.

• If the MEMO button is pushed at this

time, the CUE point is memorized as the

NEXT TRACK & point to be selected.

• The MEMO will be canceled if another

track is selected by the PARAMETERS

knob or the MEMO button is pushed

again.

NOTE:

MP3 files with Memo’s are not supported

for this function.

T

ET

O

E

C

H

O/

L

OOP

FLAN

G

E

R

FI

L

TE

L

R

BRAKE

C

U

E

J

E

CT

DI

SC

r, i

t

e

P

ARAMETER

P

S

P

US

H

O

N

/O

F

EVERSE

PIT

CH

RAN

GE

K

EY ADJ

UST

F

H

M

O

D

E

FILE

S

EAR

CH

REL

A

Y

A

CON

T

.

T

q, y

w, u

6

Next Track Auto mode

y When the NEXT TRACK

button is pushed during

playback, the NEXT TRACK

function is turned on.

u

Press the PARAMETERS knob for 2 secouds,

then the NEXT TRACK AUTO mode is set.

Playback mode is set to the CONT. mode.

i When the CUE button is pressed, the NEXT

TRACK AUTO mode is started.

In the NEXT TRACK mode, the NEXT TRACK

button flashes.

NOTE:

If Playback is interrupted during this mode

by Pause, Cue, Hot Start or track change,

the Next Tr Auto Mode is cancelled and

normal playback resumes.

NEXT TRACK

9

ENGLISH

8

SEAMLESS LOOP/HOT START/STUTTER

P

O

WE

ON

O

F

P

ARAMETER

P

S

P

US

H

O

N

/O

FF

BTRIM

C

L

R

T

.

T

ET

O

S

A

M

P

.

P

B

RE

V

.

V

PITCH/

V

/

OL

.

REL

OOP

EXIT

/

M

O

D

E

FILE

S

EAR

CH

BTRIM

A2

B

REL

A

Y

A

CON

T

.

T

q, w, y r

t, y e, y

1

4

Setting the A point

(loading the Hot Start data)

q Push the A1 or A2 button to

set the A point. (Hot Start

data loading starts.)

• A1 and A2 buttons can be

used separately for each

Hot Start.

•

When an A point is set, the corresponding

A button and “ ” display lights up and

that button is set to the Hot Start mode.

• The BPM is set independently for each

Hot Start automatically.

Playing Seamless Loops

• When the B point for A1 is detected after

playback started from A1 point, playback

returns to A1 point with seamless. While

A1 to B looping, B point for A2 is ignored.

• When the B point for A2 is detected after

playback started from A2 point, playback

returns to A2 point with seamless. While

A2 to B looping, B point for A1 ignored.

3

-2

• If the B button is pushed during Seamless

Loop playback or after EXIT playback, the

B point moves to the point at which the

button was pushed.

• When the B point is set, the B and “ ”

indicators light up in the display.

A1

Seamless Loop/Hot Start/Stutter (A1, A2 buttons)

2

Starts Hot Start

w

When A1 or A2 button is

pushed, Hot Start playback

starts from the corresponding

A point.

A1

3-1

Setting the B point for Seamless Loop

e When the B button is

pushed after setting the A

point or after starting Hot

start playback, the B point is

set and Seamless Loop

playback starts from the A

point.

• The B button works with respect to the A

point.

B

5

Exit/Reloop

r In Seamless Loop playback,

you can force exit or return

to the loop.

EXIT:

During Seamless Loop

playback, push the EXIT/RELOOP button to

exit from loop. DN-S3500 continues

playback after the B point.

RELOOP:

When the EXIT/RELOOP button is pushed

after exit the loop, Seamless Loop playback

resumes from the A point instantly.

RELOOP

EXIT/

Operation display (refer to the

section describing the display)

7

SCRATCH

P

ARAMETER

P

S

P

US

H

O

N

/O

F

T

.

T

ET

E

C

H

O/

L

OOP

FLAN

G

E

R

FI

L

TE

L

R

BRAKE DUMP

REVER

SE

PIT

CH

RAN

GE

K

EY ADJ

UST

F

H

C

U

E

J

E

CT

DI

SC

REL

A

Y

A

q

w

e

You can Scratch in CD or Sampler mode.

3

Scratch Disc

e When MAIN is selected as

the Scratch mode and

Scratch Disc is turned by

hand, the Main Track (CD)

is being scratched.

When SAMPLER is selected as the Scratch

mode and Scratch Disc is turned by hand,

the sample is being scratched.

2

Select Scratch direction

w Select the direction for

scratching using the

SCRATCH direction select

lever.

B

O

T

H

FWD

1

Select Platter source

q

Select the source to be

scratched using the PLATTER

SOURCE button.

MAIN: The PLATTER SOURCE button

lights up in orange.

SAMPLER: The PLATTER SOURCE button

lights up in green.

(Only when a sample is loaded)

SOURCE

10

ENGLISH

9

B TRIM

P

ARAMETER

P

S

P

US

H

O

N

/O

FF

BTRIM

C

L

R

T

.

T

ET

O

ECHO/LOOP

RE

V

.

V

PITCH/

V

/

OL

.

REL

OOP

EXIT

/

M

O

D

E

FILE

S

EAR

CH

BTRIM

A2

B

REL

A

Y

A

CON

T

.

T

e w, r

q

r q

1

Seamless Loop:

q When the B TRIM button is

pressed during seamless

loop playback, the B TRIM

mode is turned on.

To cancel B TRIM mode,

press the B TRIM button again.

Sampler Loop:

q When the PITCH/VOL.

button is pressed for more

than 0.5 sec during Sampler

Loop playback, the B TRIM

mode is turned on.

3

2

• The Seamless Loop and Sampler B points can be fine-adjusted using the Scratch Disc.

•Trim the points during loop playback as a rehearsal.

B Trim

4

B TRIM

PITCH/VOL.

Select B point

w

The A button illumination

automatically flashes for the

last loop created or

accessed.

•

Press button A1 or A2.

The loop whose B point is to be adjusted is

selected.

A1

Trim B point

e Turn Scratch Disc slowly to

move the B point 1 frame

at a time.

• Range for trimming B point is limited as

follows.

B point for Loop:

Between 5 frames after A point and

disc end.

B point for Sampler:

Between 5 frames after A point and

Sampler end.

*MP3

Between 5 frames after A point and file

end.

Save the B point

r Push the A or SAMP button

again to save new B point,

and the unit automatically

exits from the B Trim mode.

A1

6

Stutter

• A1 and A2 points can be also used for

Stutter playback.

t To enable stutter playback,

push FLIP button for A1/A2

buttons, then “ ” display

turns off.

Press the FLIP button to

switch between the Hot

Start/Seamless Loop and Stutter modes.

7

Clear the A1/A2 point

y While pressing the FLIP/(CLR) button, push

the A1 or A2 button to clear the

corresponding A and B points.

Or push the FLIP button for more than 1

sec to clear both A1 and A2 points at once.

Quickly pressing the “FLIP” button first

and then A1, A2 or B buttons will clear

these points individually.

CLR

FLIP

A1

CLR

FLIP

11

ENGLISH

Adjust sound level

The Sampler playback sound level can be adjusted.

!3 Push the PITCH/VOL. button again when the pitch

input mode, the sound level input mode is set,

PARAMETERS LED flashes and the current

settings are displayed on the character display.

• Start Sampler playback.

!4 Turning the PARAMETERS knob can change the

output sound level.

!5 Push the PITCH/VOL. button again to turn the

sound level input mode off.

Adjust pitch

The Sampler playback pitch can be adjusted.

!1 Push the PITCH/VOL. button, the pitch input mode

is set, PARAMETERS LED flashes and the current

settings are displayed on the character display.

• Start Sampler playback.

!2 Turning the PARAMETERS knob can change the

pitch.

✽

When pushing down and turning the PARAMETERS

knob, you can change the pitch range 10 times

faster.

6

Exit and Reloop

u

The EXIT/RELOOP button

can be used same as

Seamless Loop function.

7

Reverse Play

i You can play the Sampled

sound in reverse by pushing

the REV button. In reverse

play mode REV LED lights

up and the platter spins

backwards.

• Reverse playback will take affect when

you push the SAMP button after reverse

mode has been turned on. To return to

normal forward playback, push the REV

button once again.

9

Clearing the Sampler data

!0 During the Sampler stop mode, press the

REV/(CLR) button, while pushing the SAMP

button to clear the Sampler.

•Or, by pushing the REV/(CLR) button for

more than. 1 sec, you can clear Sampler.

8

Moving Sampler B point

o When the B button is

pushed during Sampler

playback, the B point

moves to the point at which

the button was pushed, and

loop playback from point A starts.

RELOOP

EXIT/

CLR

REV.

B

SAMP.

CLR

REV.

BTRIM

C

L

R

T

.

T

ET

O

RE

V

.

V

PITCH/

V

/

OL

.

q, r, !0, !6, !7

i, !0

!1, !3, !5, !6

y, u

w, o, !6

e, t, !7

P

ARAMETER

P

S

P

US

H

O

N

/O

FF

REL

OOP

EXIT

/

M

O

D

E

FILE

S

EAR

CH

BTRIM

A2

B

REL

A

Y

A

CON

T

.

T

!2, !4

1

Record in Sampler

q When the SAMP button is

pushed in the standby or

play mode, the sound from

SAMP point is recorded to

Sampler memory up to 15

seconds.

• The SAMP button is flashing while

recording and a 15 sec REC countdown

display will appear. When the recording is

completed, the button turns off and the

corresponding SAMP B LED lights up.

• The remain time of the Sampler memory

is displayed in the character display.

4

Play Sampler sound

r Playback of the Sampler

sound starts when the

SAMP button is pushed

after recording has

stopped.

• Sampler playback continues looping.

When setting a B point, playback loops

between A and B point. Without a B point

the Sampler loops the whole recorded

length (about 15 seconds).

t To stop the Sampler sound

push the STOP button.

• Stutter playback of the

sample is possible when

the STOP button is

pushed repeatedly in the STOP mode.

SAMP.

Stop recording

e To stop the sampler

recording, press the STOP

button at any time prior to

15 sec.

• The EXIT/RELOOP LED

light to indicates Sampler Loop mode is

set automatically.

3

SAMP.

STOP

DN-S3500 has one Sampler of 15 seconds in length. This Sampler can also be looped and scratched during playback.

2

Setting B point

w When the B button is

pushed during Sampler

recording, the Sampler

Loop B point is set and the

loop mode turns on.

• Recording continues for approximately 15

seconds without stopping after set B

point.

• If the B point is not set, the recording end

point is set as your B point automatically.

Also EXIT/RELOOP LED light to indicates

Sampler Loop mode is set automatically.

B

Select Sampler Loop mode

You can select 1 of 3 playback modes for

Sampler when the Sampler is not playing.

Loop! (default):

Sampler playback continues with

looping.

(EXIT/RELOOP LED stays lit)

Single All!:

Sampler playback continues over B

point up to recording length.

(EXIT/RELOOP LED flashes)

Single B!:

Sampler playback stops at B point.

(EXIT/RELOOP LED turned off)

y

To select loop mode, push

EXIT/RELOOP button after

recording and before playing.

5

RELOOP

EXIT/

STOP

10

SAMPLER

Copy from A1/A2 sound

You can copy A1/A2 Seamless Loop into the Sampler

up to 15 sec.

!6 Copy from A1

• When the B button of the Sampler is pressed,

“SAMP

0 A1” and “Copy/Push Samp” are

displayed.

Then quickly push the SAMP button, the copying

is completed within seconds.

!7 Copy from A2

• When the STOP button is pressed, “SAMP

0

A2” and “Copy/Push Samp” are displayed.

Then quickly push the SAMP button, the copying

is completed within seconds.

NOTES:

•

You can not copy when the Sampler is already loaded.

•You can copy just your Hot Start A1/A2 points

(without a B point set) for up to 15 sec in the Cue

mode.

12

ENGLISH

11

AUTO BPM COUNTER

T

.

T

ET

O

E

C

H

O/

L

OOP

FLAN

G

E

R

RE

V

.

V

PITCH/

V

/

OL

.

q, w, e, t

P

ARAMETER

P

S

P

US

H

O

N

/O

FF

F

H

REL

OOP

EXIT/

M

O

D

E

FILE

S

EAR

CH

BTRIM

REL

A

Y

A

CON

T

.

T

r

1

BPM LOCK

The data measured by the

auto BPM counter is locked.

q Push the TAP button once

while auto BPM counter is

operating.

“BPM Lock” is displayed for 1 second.

3

2

AUTO BPM COUNTER

Beats per minute (BPM) of a track is measured automatically and displayed during playback or in Cue

standby mode.

Measured BPM values are synchronized with the effector parameters such as:(ECHO/LOOP and FLANGER

time)

• When Auto BPM COUNTER is off, pushing the TAP button for 1 second, reactivates the AUTO BPM

COUNTER to turn back on.

• If you change or select a new track, the old BPM is cleared and the Auto BPM Counter starts to detect

the new track automatically.

TAP

TAPPING

The interval when the TAP button is pushed

repeatedly is measured and BPM is calculated.

w When you push the TAP

button, the auto BPM

counter turns off.

Push the TAP button

repeatedly about 5~10

times according to the

beat.

MANUAL INPUT

The known BPM can be dialed in directly by the

numerical value.

e The BPM manual input mode is available

when the TAP button is pushed for more

than 2 sec. “Manual In” is displayed is the

character display.

r You can input BPM value

directly with the EFFECTS

knob.

t When the TAP button is

pushed again, the BPM

manual input mode is

saved and the BPM is

locked to that value for

that Track.

NOTE:

AUTO BPM COUNTER might not me able to be measured correctly according to the type of music.

*If this happens, please use the TAP feature.

TAP

AUTO BPM COUNTER/EFFECTOR

T

.

T

ET

E

C

H

O/

L

OOP

FLAN

G

E

R

FI

L

TE

L

R

q, e

r, y

u, o

w, t, i

P

ET

O

RE

CO

*2

*4

*6

*1

*3

*5

1-1

ECHO/LOOP ON

q When the ECHO/LOOP

button is pressed, the

echo/loop function is turned

on.

1-3

1-2

Set the parameters

w The echo/loop parameters can be selected

with EFFECTS knob and PARAMETERS

knob.

Echo Feedback number:

Turn the EFFECTS knob.

*1 The Echo Feedback

number is displayed in

the playback position

indicators.

Echo Time:

Turn the PARAMETERS knob.

*2 The Echo time is displayed in the

character display.

• When the EFFECTS knob is pressed, the

parameter display is swited to the normal

display.

•To return to the parameter display, press

or turn the EFFECTS knob.

One of the 7 effects can be selected.

ECHO/LOOP

DRY WET

EFFECTS

ECHO/LOOP

Select the LOOP mode

When the feedback number is set to the

maximum, loop playback with the specified

time begins. Other tracks can be selected or

the disc can be replaced for seamless play.

ECHO LOOP FADE OUT

• The parameter mode is turned off while the

echo loop is playing when the back cue or

NEXT TRACK is selected at the parameter

selection mode.

• When the new track is selected and playback

is started, echo loop playback stops by fade

out. An echo loop playback and a normal

playback can be smoothly replaced.

• The disc can also be ejected during Echo

Loop and replaced with a new disc without

interrupting the sound. Once a new track is

selected and PLAY is pushed, the echo loop

starts to automatically fade out.

EFFECTOR

1-4

ECHO/LOOP OFF

e If the ECHO/LOOP button

is pressed again, the

echo/loop function is turned

off.

ECHO/LOOP

DRY WET

EFFECTS

TRACK SEARCH

PARAMETERS

PUSH ON/OFF

•

ECHO LOOP mode can be used in many ways for

advanced remixing. For example, during ECHO LOOP

you can shorten the original feedback time to chop

the beats in half each time the PARAMETERS knob is

turned counter clockwise. Once the minimun

feedback time of 1/8 (or other) is reached, you can

push down the PARAMETERS knob to instantly return

back to the original ECHO LOOP sound. For even

more creative control, the Pitch Slider and Key Adjust

are functional with ECHO LOOP after it has been set.

13

ENGLISH

2-1

FLANGER ON

r When the FLANGER button

is pressed, the flanger

function is turned on.

2-2

Set the parameters

t The flanger parameters can be selected

with EFFECTS knob and PARAMETERS

knob.

FLANGER Gain:

Turn the EFFECTS knob.

*3

The FLANGER gain is

displayed in the playback

position indicators.

FLANGER Time:

Turn the PARAMETERS knob.

*4 The FLANGER time is displayed in the

charactor display.

• When the EFFECTS knob is pressed, the

parameter display is swited to the normal

display.

•To return to the parameter display, press

or turn the EFFECTS knob.

FLANGER

FLANGER OFF

y If the FLANGER button is

pressed again, the flanger

function is turned off.

3-1

FILTER ON

u When the FILTER button is

pressed, the filter function

is turned on.

3-2

Select the parameters

i The filter parameters can be selected with

EFFECTS knob and PARAMETERS knob.

Filter Frequency:

Turn the EFFECTS knob.

*5

The Filter frequency is

displayed in the playback

position indicators.

Filter types:

Turn the PARAMETERS knob.

*6 The Filter types is displayed in the

character displayed.

• When the EFFECTS knob is pressed, the

parameter display is swited to the normal

display.

•To return to the parameter display, press

or turn the EFFECTS knob.

FILTER

DRY WET

EFFECTS

DRY WET

EFFECTS

FLANGER

2-3

FILTER OFF

o If the FILTER button is

pressed again, the filter

function is turned off.

3-3

FILTER

The DN-S3500 can playback MP3 files via CD-R/RW media made according to the following conditions.

* MP3 disc’s made by formats other than below settings cannot be played back on our system.

* In most cases, you can find the below settings within the properties of your burners PC software.

Please refer to your manual or contact your software vendor for assistance regarding these settings.

NOTES:

• Depending on the type of MP3 encoding or writing software, with some files noise may be generated or

it may not be possible to play the file.

• Recordings you make are for your personal use and should not be used in ways infringing upon the

copyright holder as per copyright laws.

MP3 FORMAT

note #1 Cannot playback files in a folder located further from the specified Folder/directory hierarchical level.

note #2 The number of total folders is not limited, while the number of total files is limited.

note #3 If the number of files exceeds 999, the unit can play first 999 files, and no further files are recognized.

MP3 PLAYBACK

12

Disc Format

Applicable file extensions

ISO9660

Joliet

Romeo

CD-ROM sector format

Folder/directory hierarchical level

Max. number of Folders

Max. number of files

.mp3 .MP3 .mP3 .Mp3

Level 1(max. 8/”8.3” character style)

max. 64/64 character style

mode-1 only

max. 8 levels down (* note #1)

No limit (* note #2)

max. 999 files (* note #3)

Level 2 (max. 31/30 character style)

MP3 Format

MPEG-1

Encording

NOTE: .m3u Play List are not supported.

Audio Layer-3 32-320kbps, f/s 44.1kHz

C.B.R , V.B.R

V1.0, V1.1, V2.2, V2.3, V2.4

Disc Writing Method

Disc at Once and Track at Once

Multi Session

NOTE: Packet Write is not supported.

If the 1st session is CDDA ,you can

playback only CDDA track. If the 1st session

is MP3,you can playback only MP3 file.

Display

• The elapsed file playing time and the remaining file

playing time (for C.B.R files only) can be selected.

•

The file name display, folder name display and ID-3 tag

of (title/artist name/album name) can be displayed.

Each time the @2 TITLE button is pushed, the file and

folder name display, title display, artist name display

or album name display are selected.

NOTE:

Title, Artist and Album name utillzes the data of ID-3

tag.

It is not data of a file name.

If no ID-3 tag is found, the display will indicate “No

Data”.

Play, Pause and Cue

• Like with a normal CD, it is possible to play, pause,

back-cue, etc.

• Pitch range, 4%, 10%, 16%

NOTE:

When you back cue V.B.R.encoded files, the start

position returns to the head of file 00:00:00 rather

than where music is detected.

ID-3 Tag

TRACK SEARCH

PARAMETERS

PUSH ON/OFF

TRACK SEARCH

PARAMETERS

PUSH ON/OFF

14

ENGLISH

Select the file

Select the file search modes

For MP3 discs, the file search modes

described below can be selected by pushing

the @6 FILE SEARCH MODE button.

•

The file search mode is selected by turning

the @7 PARAMETERS knob and set by pushing

the knob.

2

File search (File.NO)

•When the @7 track select knob is turned, file

searching is performed in the order of the file

numbers.

•When the @7 track select knob is pushed in

and turned, file searching is performed 10

files at a time.

3

File/Folder search (Folder)

•When the @7 track select knob is turned, file

searching is performed in the order of the file

numbers.

•When the @7 track select knob is pushed in

and turned, folder searching is performed in

the order of the folder numbers.

4

Artist name search (Artist)

Title name search (Title)

If the artist name or title name is recorded in

the file name as described below, it is possible

to search in alphabetical order of artist or title

names.

• When recorded in order of artist name and

title name (Artist - title, (Artist)(Title),

[Artist][Title]) and with “-”, “()” or “[]”

between artist names and title names, it is

possible to search artist names and title

names in alphabetical order.

NOTES:

• These name search functions cannot be

selected unless the file names are recorded

in the specified format.

•Title and artist name use the data of a file

name. It is not data of ID-3 tag.

•When the artist name search or title name

search mode is selected and the @7 track

select knob is pressed in while turned, name

search is performed in the alphabetical order

of the names.

• If the @7 track select knob is turned after

searching in alphabetical order is finished, file

searching is performed in the order of the file

numbers from the name with the selected

letter.

• If the o CUE button is pushed after file

searching, the searched file is searchedfor

and the standby mode is set.

5

File name search (File_Name)

Files can be searched for by file name in

alphabetical order.

• When the file name search function is

selected and the @7 track select knob is

pushed in while turned, the file names are

search in alphabetical order.

• If the @7 track select knob is turned after

searching in alphabetical order is finished, file

searching is performed in the order of the file

numbers from the file name with the

selected letter.

• If the o CUE button is pushed after selecting

the file, the selected file is searched for and

the standby mode is set.

Manual search & Fast search

For only C.B.R files, manual searching and fast

searching can be performed.

NOTES:

•With manual searching and fast searching, it is only

possible to search within the selected file.

• Manual searching in the reverse direction is possible

up to the point 10 seconds before the point at which

searching starts.

• The searching speed may vary according to the file’s

compression rate, etc.

Scratch

Scratch playback is possible in the same way as with

normal CDs.

NOTE:

Scratching (back spinning) in the reverse direction is

possible up to the point 10 seconds before the point at

which reverse playback was started.

NOTE:

When the file name dose not correspond to the format

of 4, file name search is selected.

Seamless Loop/Hot start/Stutter

For only C.B.R files, hot starting, seamless loop

playback and stuttering can be performed in the same

way as with normal CDs.

NOTE:

The A and B points for the seamless loop must both

be set within the same file.

Platter Effect

Platter effect is supported in the same way as with

normal CDs.

NOTE:

Reverse playback is performed for a maximum of 10

seconds, after which playback returns to normal.

Memo

Memo is supported in the same way as with normal

CDs.

NOTES:

• Next track Memo function is not supported.

• MEMO CALL may not be completed according to

the file condition.

BPM ID3 Tag

If an MP3 file contains BPM ID3 Tag information, the

DN-S3500 will automatically read and LOCK the BPM

data accordingly. You can always return back to AUTO

BPM mode by pushing the TAP button for more than

1 sec.

NOTE:

May not be compatible with some software based

systems.

1

La pagina sta caricando ...

Denon DN-S3500 Manuale del proprietario

Denon DN-S3500 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti