Videotec ULISSE RADICAL Manuale utente

ENGLISH ITALIANO FRANÇAIS DEUTSCH

РУССКИЙ

EN

English - Instructions manual

IT

Italiano - Manuale di istruzioni

FR

Français - Manuel d’instructions

DE

Deutsch - Bedienungslanleitung

RU

Русский - Руководство по эксплуатации

ULISSE RADICAL

PTZ unit with integrated camera and lens

EN

English - Instruction manual

ENGLISH

ULISSE RADICAL

PTZ unit with integrated Kamera and lens

Instruction manual - English - EN

3MNVCUPKHXL_1625_EN

Contents

ENGLISH 1

1 About this manual ......................................................................................................... 6

1.1 Typographical conventions .................................................................................................................................. 6

2 Notes on copyright and information on trademarks .................................................. 6

3 Safety rules..................................................................................................................... 6

4 Identication .................................................................................................................. 9

4.1 Product description and type designation..................................................................................................... 9

4.2 Product marking ...................................................................................................................................................... 9

4.2.1 Checking the markings ......................................................................................................................................................... 9

5 Versions ........................................................................................................................10

5.1 LED illuminators .....................................................................................................................................................10

6 Preparing the product for use .................................................................................... 10

6.1 Safety precautions before use ...........................................................................................................................10

6.2 Unpacking ................................................................................................................................................................ 11

6.2.1 Removal of the protective packaging ............................................................................................................................ 11

6.2.1.1 How to open the housing ........................................................................................................................................................................ 11

6.2.1.2 Remove the protective packaging .......................................................................................................................................................11

6.3 Contents .................................................................................................................................................................... 12

6.4 Safely disposing of packaging material .........................................................................................................12

6.5 Preparatory work before installation .............................................................................................................. 12

6.5.1 Attaching the bracket ..........................................................................................................................................................12

6.5.2 Cables management ............................................................................................................................................................12

7 Installation ................................................................................................................... 13

7.1 Connecting the cables to the base ..................................................................................................................13

7.2 Fixing the base to the support ..........................................................................................................................14

7.3 Connector board description ............................................................................................................................ 14

7.4 Connection of the power supply line ............................................................................................................. 15

7.4.1 24Vac power line connection ............................................................................................................................................ 16

7.4.2 120Vac and 230Vac power line connection .................................................................................................................16

7.4.3 Connection of the alarm inputs, of the twilight switch and of the relays .........................................................17

7.5 Connection of the Ethernet cable....................................................................................................................17

7.6 Fixing the upper body ..........................................................................................................................................18

7.7 Counterweights installation ..............................................................................................................................18

7.8 LED illuminators installation .............................................................................................................................. 19

7.8.1 Counterweight removal ......................................................................................................................................................19

7.8.2 Fitting the illuminator on the bracket ............................................................................................................................ 19

7.9 Connection of the LED illuminators ................................................................................................................ 20

7.10 LED illuminator activation and adjustment instructions ...................................................................... 20

7.10.1 Description of the LED illuminator ...............................................................................................................................20

7.10.2 LED illuminator switching on threshold adjustment .............................................................................................21

7.10.3 LED illuminator power adjustment ..............................................................................................................................21

7.11 Fastening of the wiper blade ..........................................................................................................................22

8 Switching on ................................................................................................................23

EN - English - Instruction manual

4 MNVCUPKHXL_1625_EN

9 Conguration ...............................................................................................................24

9.1 Web interface ..........................................................................................................................................................24

9.1.1 Home Page ............................................................................................................................................................................... 24

9.1.2 User Controls page ................................................................................................................................................................25

9.1.3 Device Parameters Page ......................................................................................................................................................26

9.1.4 Device Statistics Page ..........................................................................................................................................................26

9.1.5 Network Conguration page ............................................................................................................................................26

9.1.6 User Conguration page ..................................................................................................................................................... 27

9.1.7 Movement Parameters page .............................................................................................................................................27

9.1.7.1 Autopan Page...............................................................................................................................................................................................28

9.1.7.2 Patrol Page ....................................................................................................................................................................................................28

9.1.7.3 Motions Recall Page ................................................................................................................................................................................... 28

9.1.8 Preset Parameters page .......................................................................................................................................................28

9.1.9 Preset Parameters page (Advanced) ...............................................................................................................................28

9.1.10 Digital I/O Page ....................................................................................................................................................................29

9.1.11 Washer page .........................................................................................................................................................................29

9.1.12 Camera Settings page .......................................................................................................................................................30

9.1.13 Tools Page ..............................................................................................................................................................................30

9.1.14 Factory Default .....................................................................................................................................................................31

9.2 VTTunnel ................................................................................................................................................................... 31

10 Accessories ................................................................................................................. 32

10.1 Washer ..................................................................................................................................................................... 32

10.1.1 Washing system connection ...........................................................................................................................................32

10.2 Wall mount bracket ............................................................................................................................................33

10.3 Parapet bracket .................................................................................................................................................... 33

10.4 Power supply with illuminator control ........................................................................................................33

11 Maintenance ..............................................................................................................34

11.1 Fuses replacement .............................................................................................................................................. 34

12 Cleaning ..................................................................................................................... 34

12.1 Window and plastic cover cleaning .............................................................................................................. 34

13 Disposal of waste materials ......................................................................................34

14 Troubleshooting ........................................................................................................ 34

15 Technical data ............................................................................................................ 35

15.1 General .................................................................................................................................................................... 35

15.2 Mechanical .............................................................................................................................................................35

15.3 Electrical .................................................................................................................................................................35

15.4 Communications .................................................................................................................................................35

15.5 Camera ....................................................................................................................................................................36

15.6 Lenses ...................................................................................................................................................................... 36

15.7 Environment..........................................................................................................................................................36

15.8 Certications ......................................................................................................................................................... 36

16 Technical drawings .................................................................................................... 37

Instruction manual - English - EN

5MNVCUPKHXL_1625_EN

1 About this manual

Read all the documentation supplied carefully before

installing and using this unit. Keep the manual in a

convenient place for future reference.

1.1 Typographical conventions

DANGER!

High level hazard.

Risk of electric shock. Disconnect the

power supply before proceeding with any

operation, unless indicated otherwise.

DANGER!

Hot surface.

Avoid contact. Surfaces are hot and may

cause personal injury if touched.

DANGER!

Mechanical hazard.

Risk of crushing or shearing.

CAUTION!

Medium level hazard.

This operation is very important for the

system to function properly. Please read

the procedure described very carefully and

carry it out as instructed.

INFO

Description of system specications.

We recommend reading this part carefully

in order to understand the subsequent

stages.

2 Notes on copyright and

information on trademarks

The quoted names of products or companies are

trademarks or registered trademarks.

3 Safety rules

CAUTION! The electrical system to which

the unit is connected must be equipped

with a 20A max automatic bipolar circuit

breaker. This circuit breaker must be of

the Listed type. The minimum distance

between the circuit breaker contacts must

be 3mm (0.1in). The circuit breaker must be

provided with protection against the fault

current towards the ground (dierential)

and the overcurrent (magnetothermal).

CAUTION! Hazardous moving parts. Keep

ngers and other body parts away.

CAUTION! Device installation and

maintaining must be performed by

specialist technical sta only.

CAUTION! For continued protection against

risk of re, replace only with same type and

rating of fuse. Fuses must be replaced only

by service personnel.

CAUTION! TNV-1 installation type. The

installation is type TNV-1, do not connect it

to SELV circuits.

CAUTION! In order to reduce the risk of re,

only use UL Listed or CSA certied cables

with sections greater than or equal to

0.14mm² (26AWG).

• The manufacturer declines all responsibility

for any damage caused by an improper use

of the appliances mentioned in this manual.

Furthermore, the manufacturer reserves the right

to modify its contents without any prior notice.

The documentation contained in this manual has

been collected with great care. The manufacturer,

however, cannot take any liability for its use. The

same thing can be said for any person or company

involved in the creation and production of this

manual.

EN - English - Instruction manual

6 MNVCUPKHXL_1625_EN

• Before starting any operation, make sure the

power supply is disconnected.

• Be careful not to use cables that seem worn or old.

• Never, under any circumstances, make any

changes or connections that are not shown in

this handbook. Improper use of the appliance

can cause serious hazards, risking the safety of

personnel and of the installation.

• Use only original spare parts. Non-original spare

parts could cause re, electrical discharge or other

hazards.

• Before proceeding with installation, check the

supplied material to make sure it corresponds

to the order specication by examining the

identication labels (4.2 Product marking, page 9).

• Installation category (also called Overvoltage

Category) species the level of mains voltage

surges that the equipment will be subjected to.

The category depends upon the location of the

equipment, and on any external surge protection

provided. Equipment in an industrial environment,

directly connected to major feeders/short branch

circuits, is subjected to Installation Category III. If

this is the case, a reduction to Installation Category

II is required. This can be achieved by use of an

insulating transformer with an earthed screen

between primary and secondary, or by tting UL

listed Surge Protective Devices (SPDs) from live

to neutral and from neutral to earth. Listed SPDs

shall be designed for repeated limiting of transient

voltage surges, suitable rated for operating voltage

and designated as follows: Type 2 (Permanently

connected SPDs intended for installation on the

load side of the service equipment overcurrent

device); Nominal Discharge Current (In) 20kA min.

For example: FERRAZ SHAWMUT, STT2240SPG-

CN, STT2BL240SPG-CN rated 120Vac/240Vac,

(In=20kA). Maximum distance between installation

and reduction is 5m.

• This device was designed to be permanently

secured and connected on a building or on a

suitable structure. The device must be permanently

secured and connected before any operation.

• A power disconnect device must be included

in the electrical installation, and it must be very

quickly recognizable and operated if needed.

• The separate protective earthing terminal provided

on this product shall be permanently connected

to earth.

• Connect the device to a power source

corresponding to the indications given on the

marking label. Before proceeding with installation

make sure that the power line is properly isolated.

The supply voltage should never exceed the limit

(±10%).

• Power supply must be provided with a SELV type,

24Vac, 8A isolated source derived from a double

isolation UL Listed transformer specially protected

in output.

• The appliance includes moving parts. Make sure

that the unit is positioned where it is inaccessible

under normal operating conditions.

• Attach the Dangerous Moving Parts label near the

device. (Fig. 3, page10).

• Do not use the appliance in the presence of

inammable substances.

• To connect the power supply line use the

appropriate junction-box (UPTJBUL). For further

information, refer to the product use and

installation manual.

Instruction manual - English - EN

7MNVCUPKHXL_1625_EN

• Do not allow children or unauthorised people to

use the appliance.

• Only skilled personnel should carry out

maintenance on the device. When carrying out

maintenance, the operator is exposed to the risk of

electrocution and other hazards.

• Use only the accessories indicated by the

manufacturer. Any change that is not expressly

approved by the manufacturer will invalidate the

guarantee.

• Before connecting all the cables make sure the

device is properly connected to the earth circuit.

• If the device has to be removed from the

installation, always disconnect the earth cable last.

• Take all necessary precautions to prevent the

apparatus from being damaged by electrostatic

discharge.

• The unit has been made for connection using a

3-pole cable. To make a correct connection to

the earth circuit, follow the instructions in this

handbook.

• Handle the unit with great care, high mechanical

stress could damage it.

• Make especially sure that the power supply line is

insulated at a sucient distance from all the other

cables, including lightning protection devices.

• If it is necessary to transport the device, this should

be done with great care. Abrupt stops, bumps and

violent impact could damage the unit or injure the

user.

EN - English - Instruction manual

8 MNVCUPKHXL_1625_EN

4 Identication

4.1 Product description and type

designation

ULISSE RADICAL is the rst Videotec ready to use

network Full HD PTZ camera system that integrates

exceptional factory-assembled combinations of

camera and lens, Full HD 1080p, 60fps and 1/2" CMOS

sensor, for day and night time broadcast quality video

of extended outdoor areas.

To meet the most demanding video surveillance

specications, this PTZ camera unit is supplied

with 18x or 33x lenses equipped with an advanced

autofocus that allows and automatically maintains

the focus on subjects at far distances with sharp

details.

ULISSE RADICAL is certied ONVIF Prole S and is

compatible with most VMS on the market.

The Videotec's PTZ ASSISTANT plug-in software

supports any VMS with the control of all special

functions such as wiper, washer pump, IR and Auto

Focus.

Powerful motors guarantee exceptionally smooth

tracking, even at a minimum speed of 0.02°/sec.

The performance remains optimal in complete

darkness thanks to powerful LED illuminators that

can reach distances of over 300m (985ft) with two

UPTIRN illuminators (10°, 850nm).

ULISSE RADICAL with 33x zoom features a Thermal

Compensation System and a Visible Cut Filter.

Due to its characteristics of accuracy, reliability and

robustness, this PTZ camera is the ideal solution for

the visual control of large outdoor areas, such as:

border patrol, harbour surveillance, long distance

perimeter surveillance, trac and highway control,

military installations.

4.2 Product marking

Pan & tilt devices have a label complying

with CE markings.

Fig. 1

The label shows:

• Model identication code (Extended 3/9 bar code).

• Supply voltage (Volt).

• Frequency (Hertz).

• Current consumption (Amps).

• Weatherproof standard (IP).

• Serial number.

4.2.1 Checking the markings

Before proceeding further with installation, make

sure the material supplied corresponds to the order

specication by examining the marking labels.

Never, under any circumstances, make any changes

or connections that are not shown in this handbook.

Improper use of the appliance can cause serious

hazards, risking the safety of personnel and of the

installation.

Instruction manual - English - EN

9MNVCUPKHXL_1625_EN

5 Versions

5.1 LED illuminators

The version with LED illuminators can only

powered at 24Vac.

The pan & tilt can be tted with bracket for 2

VIDEOTEC LED illuminators for night surveillance

(illuminators not included).

Fig. 2

For further information refer to the relative

chapter (7.8 LED illuminators installation,

page19).

6 Preparing the product for

use

Any change that is not expressly approved

by the manufacturer will invalidate the

guarantee.

The unit must not be dismantled or

tampered with. The only exceptions

are those concerning the assembly and

maintenance operations stipulated in this

manual.

6.1 Safety precautions before use

The appliance includes moving parts. Make

sure that the unit is positioned where it

is inaccessible under normal operating

conditions. Attach the warning label

supplied with the appliance, placing it near

the unit so that it can be seen easily.

Fig. 3

EN - English - Instruction manual

10 MNVCUPKHXL_1625_EN

6.2 Unpacking

When the product is delivered, make sure that the

package is intact and that there are no signs that it

has been dropped or scratched.

If there are obvious signs of damage, contact the

supplier immediately.

When returning a faulty product we recommend

using the original packaging for shipping.

Keep the packaging in case you need to send the

product for repairs.

Unpack the sunshield of the device, taking

care not to damage the housing.

6.2.1 Removal of the protective

packaging

Remove the protective packaging before installing

the device.

6.2.1.1 How to open the housing

Loosen the leak-proof screws placed on the sides and

lift the upper part of the housing.

Fig. 4

First of all tighten the two central screws as

shown in gure.

Fig. 5

After installation and wiring, close the

product again.

6.2.1.2 Remove the protective packaging

Open the housing and remove the protective

packaging.

Fig. 6

Instruction manual - English - EN

11MNVCUPKHXL_1625_EN

6.3 Contents

Check the contents to make sure they correspond

with the list of materials as below:

• Positioning unit

• Power supply base

• Accessories package:

• Serial adaptor

• Serial extension cable

• Allen wrenches

• Spacers

• Label

• Cable ties

• Ferrite

• Silicone sheath

• Reduction gaskets for cable glands

• Instruction manual

• Attachment plate for desiccant bag

• Bolts and screws

• Counterweights package:

• Counterweights

• Counterweights brackets

• Sunshield

6.4 Safely disposing of packaging

material

The packaging material can all be recycled. The

installer technician will be responsible for separating

the material for disposal, and in any case for

compliance with the legislation in force where the

device is to be used.

6.5 Preparatory work before

installation

6.5.1 Attaching the bracket

For installations subject to vibrations, only

use the parapet bracket.

Dierent types of supports are available (10

Accessories, page32). Choose a suitable bracket for

the installation and follow all the instructions in the

suggested chapter.

Take special care when attaching and

fastening down the apparatus. The

clamping system must be able to support

at least 4 times the weight of the entire

equipment, including P&T, lenses and

camera.

The device should be assembled vertically.

Any other position could impair the

performance of the appliance.

Do not attach the device upside down.

6.5.2 Cables management

The connection cables should not be

accessible from the outside. It is necessary

to fasten the cables securely to the support

in order to prevent excessive weight pulling

them out accidentaly.

You must use cables suited to the type of

installation.

Insert the cables into the support so that they

protrude by about 50cm.

50cm50cm

Fig. 7

EN - English - Instruction manual

12 MNVCUPKHXL_1625_EN

7 Installation

Never, under any circumstances, make

any changes or connections that are not

shown in this handbook. Failure to follow

the connection instructions that are given

in the handbook may create serious safety

hazards for people and for the installation.

Do not change the wiring in the product

as it is supplied to you. Failure to follow

this instruction may create serious safety

hazards for people and for the installation,

and will also invalidate the guarantee.

If using the washer kit, the nozzle support

should be installed before positioning

the pan & tilt and the wiring. For further

explanations see the specic handbook for

the kit.

Fig. 8

Inside the bottom cover there is a desiccant

bag that is used to prevent moisture

formation in the base and near the

connector boards. Remove the bag before

installation.

7.1 Connecting the cables to the

base

Insert the cables into the cable glands holding the

base at about 20cm from the support. Tighten the

cable glands. The cable glands are suitable for cables

with a diameter between 5mm and 10 mm.

Fig. 9

Pay attention to the xing. Tightening

torque: 5Nm.

For cables diameter from 3mm to 7mm use

the supplied gaskets.

Fig. 10

Instruction manual - English - EN

13MNVCUPKHXL_1625_EN

7.2 Fixing the base to the support

Use the screws and the washers supplied

with the base.

Once you have positioned the gasket (01), x the

base (02) onto the bracket (03) with screws (04),

serrated washers (05) and screw rings (06).

01

03

06

05

04

02

Fig. 11

01

03

06

05

04

02

Fig. 12

Align the 3 notches on the base with those on the

support as shown in the following gure.

Fig. 13

Apply a thread-locker on the holes of the

screws (Loctite 243®).

Pay attention to the xing. Tightening

torque: 6Nm.

7.3 Connector board description

CONNECTOR BOARD DESCRIPTION

Connector/

Component

Function

CN1 Board power supply

CN4 Signal cables

Ethernet Ethernet

F1 Fuse

F2 Fuse

Tab. 1

F1

CN1

F2

CN4

Ethernet

Fig. 14

EN - English - Instruction manual

14 MNVCUPKHXL_1625_EN

7.4 Connection of the power

supply line

Depending on the version, the device can be

provided with dierent power supply voltages. The

power supply voltage is indicated on the product

identication label. (4.2 Product marking, page9).

Electrical connections must be performed

with the power supply disconnected and

the circuit-breaker open.

When commencing installation make sure

that the specications for the power supply

for the installation correspond with those

required by the device.

Check that the power supply socket and

cable are adequately dimensioned.

Earth cable should be about 10mm longer

than the other two, so that it will not be

disconnected accidentally if pulled.

The power supply cable must be covered

by the silicone sheath (01) supplied. The

silicone sheath must be fastened with the

corresponding cable tie (02).

Fig. 15

CN1

N

L

a

01

02

Instruction manual - English - EN

15MNVCUPKHXL_1625_EN

7.4.1 24Vac power line connection

Cut the cables to the correct length and make the

connections. Connect the power supply to the

terminal: CN1.

CN1

24Vac 24Vac

a

Fig. 16

Connect the power supply cables as described in the

table below.

CONNECTION OF THE POWER SUPPLY LINE

Colour Terminals

Power supply 24Vac

Dened by the installer 24Vac

Yellow/Green

Tab. 2

7.4.2 120Vac and 230Vac power line

connection

Cut the cables to the correct length and make the

connections. Connect the power supply to the

terminal: CN1.

CN1

N L

GND

a

Fig. 17

Connect the power supply cables as described in the

table below.

CONNECTION OF THE POWER SUPPLY LINE

Colour Terminals

Power supply 230Vac

Blue N (Neutral)

Brown L (Phase)

Yellow/Green

Power supply 120Vac

Blue N (Neutral)

Brown L (Phase)

Yellow/Green

Tab. 3

EN - English - Instruction manual

16 MNVCUPKHXL_1625_EN

7.4.3 Connection of the alarm inputs, of

the twilight switch and of the relays

CAUTION! TNV-1 installation type. The

installation is type TNV-1, do not connect it

to SELV circuits.

CAUTION! In order to reduce the risk of re,

only use UL Listed or CSA certied cables

with sections greater than or equal to

0.14mm² (26AWG).

Standard version

O1 C1 O2 C2

V V

Fig. 18 Relay contact connection.

AL4

AL3

AL2

AL1

AGND

Fig. 19 Alarms connection.

Version with LED illuminators

CONNECTION OF THE ALARM INPUTS, OF THE TWILIGHT SWITCH

AND OF THE RELAYS

AL1, AL2, AL3,

AL4 e AGND

Self-powered alarm inputs referred to the AGND

shared terminal

O1-C1 e O2-C2 Clean output contacts, can be activated by alarm

or by user control

Tab. 4

Connect the twilight switch to the AGND

and AL1 terminals. AL1 is the default alarm

contact for the light sensitive switch.

7.5 Connection of the Ethernet

cable

Connect the ethernet cable to the relative connector

(Ethernet, 7.3 Connector board description, page14).

Ethernet

Fig. 20

Instruction manual - English - EN

17MNVCUPKHXL_1625_EN

7.6 Fixing the upper body

Fix the upper body (01) to the base (02) using the

xing screws (03) equipped with gaskets (04). Make

sure the base seal is present and in good condition

(05).

Pay attention to the xing. Tightening

torque: 4Nm.

02

03

05

04

01

Fig. 21

Fig. 22

There is one anchoring position between

the base and upper body. Align side

projections to obtain the correct

positioning.

7.7 Counterweights installation

Fasten the counterweights to the housing using the

screws and washers supplied.

Fig. 23

Apply a thread-locker on the holes of the

screws (Loctite 243®).

Pay attention to the xing. Tightening

torque: 16Nm.

EN - English - Instruction manual

18 MNVCUPKHXL_1625_EN

7.8 LED illuminators installation

To work properly both illuminators must be

installed together.

From Pan & Tilt, it is only possible to install

VIDEOTEC illuminators.

7.8.1 Counterweight removal

Undo the screws and remove the external

counterweights.

Fig. 24

7.8.2 Fitting the illuminator on the

bracket

Identify the front holes on the counter-weight

bracket.

Fig. 25

Place the xings of the illuminator (01) on those of

the bracket (02).

01

02

01

02

Fig. 26

Tighten the screws and the washers previously

removed.

Fig. 27

Pay attention to the xing. Tightening

torque: 6Nm.

La pagina sta caricando ...

Videotec ULISSE RADICAL Manuale utente

Videotec ULISSE RADICAL Manuale utente

in altre lingue

Documenti correlati

Altri documenti