Analog way Smart MatriX LE Manuale utente

version 4.00

USER MANUAL

MatriX LE

Smart

THANK YOU

Thank you for choosing Analog Way. By following these simple steps, you should be able to operate the

powerful Smart MatriX LE (SMX100).

TABLE OF CONTENTS

INTRODUCTION

1-1. SMART MATRIX LE OPERATING MODE

1-2. USEFUL TERMS AND DEFINITIONS

1

4

5

HARDWARE INSTALLATION

2-1. SAFETY INSTRUCTION

2-2. UNPACKING AND INSPECTION

2-3. RACKMOUNT INFORMATION

2-4. CABLE & ADAPTOR INFORMATION

2-5. HARDWARE SPECIFICATIONS

5

10

11

CONNECTING THE SMART MATRIX LE

3-1. CONNECTING THE SMART MATRIX LE

3-2. THE SMART MATRIX LE REAR PANEL

20

21

20

Input specications

Output specications

Communication specications

Environmental specications

Pin outs

HDCP compliance

Overview

Inputs #1 - #6

DVI Inputs #1 - #2

SD/HD-SDI Inputs #1 - #2

Outputs #1 and #2

1

OPERATING THE SMART MATRIX LE

4-2. THE SMART MATRIX LE MENU

4-3. WORKING WITH THE SMART MATRIX LE

4-1. THE SMART MATRIX LE FRONT PANEL

25

27

28

29

Overview

On/Off button

Menu screen

Menu scroll knob

Control section

Menu navigation

Home menu

Operating modes

Reseting default values

Smart MatriX color codes

• Settings in Native Matrix Mode

Source Input selection

Output selection settings

Audio conguration

Input selection settings

Working with Native Matrix Mode

Working with Cut, Fade or Transitions

Source Output selection

Working with Audio

Working with DSK

HOME MENU

REMOTE CONTROL SOFTWARE

5-1. THE SMART MATRIX LE RCS

40

34

40

RCS presentation

How to use the RCS

Software installation

Serial connection

Ethernet connection

Software overview

2

5-2. WORKING WITH THE RCS

43

Operating Mode

Source input conguration

Source output conguration

Keying/Titling

Working with Audio

Creating Presets

Audio conguration

Working with Presets

OPTIONAL REMOTE CONTROL SYSTEMS

6-1. AXION 2- Ref. ARC200

6-2. ORCHESTRA - Ref. ORC50

6-3. REMOTE KEYPAD - Ref. RK-300

6-4. TRIPLE REMOTE KEYPAD - Ref. TRK-800

46

48

47

49

HOW TO CONTACT US

INFORMATION ON DISPOSAL

54

CONTACT INFORMATION

54

WARRANTY AND SERVICES INFORMATION

53

8-1. ANALOG WAY LIMITED WARRANTY

8-2. SERVICES AND RMA

53

EXAMPLES AND TIPS

7-1. ABOUT EXAMPLES

7-2. EXAMPLE

7-3. EXTERNAL PROGRAMMING

50

51

52

3

INTRODUCTION

1-1. THE SMART MATRIX LE OPERATING MODE

Native Matrix Mode

Before you start setting up your Smart MatriX LE for the rst time, be sure you know what you actually want

to do with it. The Smart MatriX LE offers one operating mode, which results in a versatile video production

tool for live event staging and xed installation applications.

* NOTE * : We recommend resetting the device to its default values every time you set up your shows or

events (see the “Operating The Smart MatriX LE” chapter, p25).

This mode turns your Smart MatriX LE into a true 10 x 2 scaled matrix, while preserving seamless switching

capabilities. Main and Preview outputs can be set to different resolutions and rates. Switching between any

of the inputs can be done with the various effects (Cut, Fade, Slides…) and synchronized on both outputs.

KEYING: a “Key” is an electronic process whereby an image is electronically superimposed over another

source or background, by cutting out either a color (chroma key), or its brightness or luminance levels (Luma

Key). Keys are typically used for titles, logos and special effects.

Smart MatriX LE allows to use a live source with green or blue background and to key it over any other live

input.

1-2. USEFUL TERMS AND DEFINITIONS

BACKGROUND: a “Background” is a source, typically originating from a computer. Smart MatriX LE enables

you to work with live background sources - visually in back of all other sources.

LAYER: a “Layer” is an image display element (such as a PIP window, Key, Logos or Background) that has

an associated visual priority — either in front (or in back) of another layer.

The Smart MatriX LE can view 1 live layer.

4

CAUTION:

All of the safety and operating instructions should be read before the product is operated and should be

maintained for further reference. Please follow all of the warnings on this product and its operating instructions.

• WARNING: To prevent the risk of electric shock and re, do not expose this device to rain, humidity,

intense heat sources (such as heaters and direct sunlight). Slots and openings in the device are provided

for ventilation and to avoid overheating. Make sure the device is never placed near a textile surface that

could block the openings. Also keep away from excessive dust, vibrations and shocks.

• POWER: Only use the power supply indicated on the device of the power source. Devices equipped with

a grounding plug should only be used with a grounding type outlet. In no way should this grounding be

modied, avoided or suppressed.

• POWER CORD: The device is equipped with a main switch [On (I) /Off (O)]. The Switch ON and OFF is

initiated by the main switch.

Caution: The power cord constitute the only mean to totaly disconnect the equipment

from the main power.

Apply the following guidelines :

- The equipment connected to the network must have a release system easily

accessible and located outside the unit.

- Unplug the power cord, do not pull on the power cord but always on the plug itself.

- The outlet should always be near the device and easily accessible.

- Power supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them.

If the power supply cord is damaged, unplug the device. Using the device with a damaged power supply cord

may expose your device to electric shocks or other hazards. Verify the condition of the power supply cords

once in a while. Contact your dealer or service center for replacement if damaged.

• CONNECTIONS: All inputs and outputs (except for the power input) are TBTS dened under EN60950.

• SERVICING: Do not attempt to service this product yourself by opening or removing covers and screws

since it may expose your device to electric shocks or other hazards. Refer all problems to qualied

service personnel.

• OPENINGS: Never push objects of any kind into this product through the openings. If liquids have been

spilled or objects have fallen into the device, unplug it immediately and have it checked by a qualied

technician.

HARDWARE INSTALLATION

SAFETY INSTRUCTIONS

2-1. SAFETY INSTRUCTIONS

5

An de mieux comprendre le fonctionnement de cet appareil nous vous conseillons de bien lire toutes les

consignes de sécurité et de fonctionnement de l’appareil avant utilisation. Conservez les instructions de

sécurité et de fonctionnement an de pouvoir les consulter ultérieurement. Respectez toutes les consignes

marquées dans la documentation, sur le produit et sur ce document.

• ATTENTION: An de prévenir tout risque de choc électrique et d’incendie, ne pas exposer cet appareil à

la pluie, à l’humidité et aux sources de chaleur intense.

• INSTALLATION: Veillez à assurer une circulation d’air sufsante pour éviter toute surchauffe à l’intérieur

de l’appareil. Ne placez pas l’appareil sur ou à proximité d’une surface textile susceptible d’obstruer

les orices de ventilation. N’installez pas l’appareil à proximité de sources de chaleur comme un

radiateur ou une poche d’air chaud, ni dans un endroit exposé au rayonnement solaire direct, à des

poussières excessives, à des vibrations ou à des chocs mécaniques. Ceci pourrait provoquer un mauvais

fonctionnement et un accident.

• ALIMENTATION: Ne faire fonctionner l’appareil qu’avec la source d’alimentation indiquée sur l’appareil.

Les appareils doivent être obligatoirement connectés sur une source équipée d’une mise à la terre efcace.

En aucun cas cette liaison de terre ne devra être modiée, contournée ou supprimée.

• CORDON D’ALIMENTATION: Les appareils sont équipés d’un interrupteur général (Marche I / Arrêt

O), la mise en tension et la mise hors tension se fait en actionnant cet interrupteur général. Attention:

le cordon d’alimentation constitue le seul moyen de débrancher l’appareil totalement de l’alimentation

secteur. Pour être certain que l’appareil n’est plus alimenté, ce cordon doit être débranché de la prise

murale.

Appliquer les consignes suivantes :

- Le matériel relié à demeure au réseau, doit avoir un dispositif de sectionnement facilement accessible

qui doit être incorporé à l’extérieur de l’appareil.

- Débrancher le cordon d’alimentation de la prise murale si vous prévoyez de ne pas utiliser l’appareil

pendant quelques jours ou plus.

- Pour débrancher le cordon, tirez-le par la che. Ne tirez jamais sur le cordon proprement dit.

- La prise d’alimentation doit se trouver à proximité de l’appareil et être aisément accessible.

- Ne laissez pas tomber le cordon d’alimentation et ne posez pas d’objets lourds dessus.

Si le cordon d’alimentation est endommagé, débranchez-le immédiatement de la prise murale. Il est

dangereux de faire fonctionner un appareil avec un cordon endommagé; un câble abîmé peut provoquer un

risque d’incendie ou un choc électrique. Vériez le câble d’alimentation de temps en temps. Contactez votre

revendeur ou le service après-vente pour un remplacement.

• CONNEXIONS: Toutes les entrées et sorties (exceptée l’entrée secteur) sont de type TBTS (Très Basse

Tension de Sécurité) dénies selon EN 60950.

• RÉPARATION ET MAINTENANCE: L’utilisateur ne doit en aucun cas essayer de procéder aux opérations

de dépannage, car l’ouverture des appareils par retrait des capots ou de toutes autres pièces constituant

les boîtiers ainsi que le dévissage des vis apparentes à l’extérieur, risquent d’exposer l’utilisateur à des

chocs électriques ou autres dangers. Contactez le service après-vente, votre revendeur ou s’adresser à

un personnel qualié uniquement.

• OUVERTURES ET ORIFICES: Les appareils peuvent comporter des ouvertures (aération, fentes, etc...),

veuillez ne jamais y introduire d’objets et ne jamais obstruer ses ouvertures. Si un liquide ou un objet

pénètre à l’intérieur de l’appareil, débranchez immédiatement l’appareil et faites-le contrôler par un

personnel qualié avant de le remettre en service.

INSTRUCTIONS DE SECURITE

6

Allo scopo di capire meglio il funzionamento di questa apparecchiatura vi consigliamo di leggere bene

tutti i consigli di sicurezza e di funzionamento prima dell’utilizzo. Conservare le istruzioni di sicurezza e di

funzionamento al ne di poterle consultare ulteriormente. Seguire tutti i consigli indicati su questo manuale

e sull’apparecchiatura.

• ATTENZIONE: Al ne di prevenire qualsiasi rischio di shock elettrico e d’incendio, non esporre

l’apparecchiatura a pioggia, umidità e a sorgenti di eccessivo calore.

• INSTALLAZIONE: Assicuratevi che vi sia una sufciente circolazione d’aria per evitare qualsiasi

surriscaldamento all’interno dell’apparecchiatura. Non collocare l’apparecchiatura in prossimità o su

superci tessili suscettibili di ostruire il funzionamento della ventilazione. Non installate l’apparecchiatura

in prossimità di sorgenti di calore come un radiatore o una fuoruscita d’aria calda, né in un posto esposto

direttamente ai raggi del sole, a polvere eccessiva, a vibrazioni o a shock meccanici. Ció potrebbe

provocare un erroneo funzionamento e un incidente.

• ALIMENTAZIONE: Far funzionare l’apparecchiatura solo con la sorgente d’alimentazione indicata

sull’apparecchiatura. Le apparecchiature queste devono essere obbligatoriamente collegate su una

sorgente fornita di una efciente messa a terra. In nessun caso questo collegamento potrà essere

modicato, sostituito o eliminato.

• CAVO DI ALIMENTAZIONE: Gli apparecchi con un interrutore (commutatore) generale

(Accesso I : Speuto 0), accendere ou spagnere l’apparecchio si fa usando l’interrutore.

Attenzione: il cavo di alimentazione è il solo modo di disconnettere l’apparecchio dell’alimentazione.

Per assicurarsi che totalemente l’apparecchio non è più collegato, il cavo deve essere disconesso della

presa murale.

Seguire le instruzioni seguenti :

- Il materiale collegato a residenza alla rete, deve avere un dispositivo di sezionamento facile da

raggiongere eche deve essere inserito all’esterno del apparecchio.

- Disconnettere l’apparecchiatura dalla presa murale se si prevede di non utilizzarla per qualche giorno.

- Per disconnettere il cavo tirare facendo forza sul connettore.

- La presa d’alimentazione deve trovarsi in prossimità dell’apparecchiatura ed essere facilmente

accessibile.

- Non far cadere il cavo di alimentazione né appoggiarci sopra degli oggetti pesanti.

Se il cavo di alimentazione é danneggiato, spegnere immediatamente l’apparecchiatura.

E’ pericoloso far funzionare questa apparecchiatura con un cavo di alimentazione danneggiato, un cavo

grafato puó provocare un rischio di incendio o uno shock elettrico. Vericare il cavo di alimentazione

spesso. Contattare il vostro rivenditore o il servizio assistenza per una sostituzione.

• CONNESSIONE: Tutti gli ingressi e le uscite (eccetto l’alimentazione) sono di tipo TBTS denite secondo

EN 60950.

• RIPARAZIONI E ASSISTENZA: L’utilizzatore non deve in nessun caso cercare di riparare l’apparecchiatura,

poiché con l’apertura del coperchio metallico o di qualsiasi altro pezzo costituente la scatola metallica,

nonché svitare le viti che appaiono esteriormente, poiché ció puó provocare all’utilizzatore un rischio di

shock elettrico o altri rischi.

• APERTURE DI VENTILAZIONE: Le apparecchiature possono comportare delle aperture di ventilazione,

si prega di non introdurre mai oggetti o ostruire le sue fessure. Se un liquido o un oggetto penetra

all’interno dell’apparecchiatura, disconnetterla e farla controllare da personale qualicato prima di

rimetterla in servizio.

INSTRUZIONI DI SECUREZZA

7

Um den Betrieb dieses Geräts zu verstehen, raten wir Ihnen vor der Inbetriebnahme alle Sicherheits

und Betriebsanweisungen genau zu lesen. Diese Sicherheits- und Betriebsanweisungen für einen

späteren Gebrauch sicher aufbewahren. Alle in den Unterlagen, an dem Gerät und hier angegebenen

Sicherheitsanweisungen einhalten.

• ACHTUNG: um jegliches Risiko eines Stromschlags oder Feuers zu vermeiden, das Gerät nicht Regen,

Feuchtigkeit oder intensiven Wärmequellen aussetzen.

• EINBAU: Eine ausreichende Luftzufuhr sicherstellen, um jegliche Überhitzung im Gerät zu vermeiden.

Das Gerät nicht auf und in Nähe von Textiloberächen, die Belüftungsöffnungen verschließen können,

aufstellen. Das Gerät nicht in Nähe von Wärmequellen, wie z.B. Heizkörper oder Warmluftkappe,

aufstellen und es nicht dem direkten Sonnenlicht, übermäßigem Staub, Vibrationen oder mechanischen

Stößen aussetzen. Dies kann zu Betriebsstörungen und Unfällen führen.

• STROMVERSORGUNG: Das Gerät nur mit der auf dem Gerät bezeichnete Stromquelle betreiben. Gerät

mit geerdeter Hauptstromversorgung muss an eine Stromquelle mit efzienter Erdung angeschlossen

werden. Diese Erdung darf auf keinen Fall geändert, umgangen oder entfernt werden.

• NETZKABEL: Da die Geräte über einen Hauptschalter (An I/ Aus 0) verfügen, erfolgt die Stromversorgung

und -unterbrechung über diesen Hauptschalter.

Achtung: Das Netzkabel stellt die einzige Möglichkeit dar, das Gerät vollständig vom Netzanschluss

zu trennen. Um sicherzustellen, dass das Gerät nicht mehr versorgt wird, muss dieses Kabel aus der

Netzsteckdose ausgesteckt werden.

Bitte beachten Sie die folgenden Hinweise :

- Wenn Geräte dauerhaft am Netz bleiben, müssen sie über eine leicht zugängliche Trennvorrichtung

verfügen, die außen am Gerät angebracht sein muss.

- Das Kabel mittels dem Stecker herausziehen. Niemals am Stromkabel selbst ziehen.

- Die Steckdose muß sich in der Nähe des Geräts benden und leicht zugänglich sein.

- Das Stromkabel nicht fallen lassen und keine schweren Gegenstände auf es stellen.

Wenn das Stromkabel beschädigt ist, das Gerät sofort abschalten. Es ist gefährlich das Gerät mit einem

beschädigten Stromkabel zu betreiben; ein abgenutztes Kabel kann zu einem Feuer oder Stromschlag

führen. Das Stromkabel regelmäßig untersuchen. Für den Ersatz, wenden Sie sich an Ihren Verkäufer

oder Kundendienststelle.

• ANSCHLÜSSE: Bei allen Ein- und Ausgängen (außer der Stromversorgung) handelt es sich, gemäß EN

60950, um Sicherheits Kleinspannunganschlüsse.

• REPARATUR UND WARTUNG: Der Benutzer darf keinesfalls versuchen das Gerät selbst zu reparieren,

die Öffnung des Geräts durch Abnahme der Abdeckhaube oder jeglichen anderen Teils des Gehäuses

sowie die Entfernung von außen sichtbaren Schrauben zu Stromschlägen oder anderen Gefahren für den

Benutzer führen kann. Wenden Sie sich an Ihren Verkäufer, Ihre Kundendienststelle oder an qualizierte

Fachkräfte.

• ÖFFNUNGEN UND MUNDUNGEN: Die Geräte können über Öffnungen verfügen (Belüftung, Schlitze,

usw.). Niemals Gegenstände in die Öffnungen einführen oder die Öffnungen verschließen. Wenn eine

Flüssigkeit oder ein Gegenstand in das Gerät gelangt, den Stecker herausziehen und es vor einer neuen

Inbetriebnahme von qualiziertem Fachpersonal überprüfen lassen.

SICHERHEITSHINWEISE

8

Para comprender mejor el funcionamiento de este aparato, le recomendamos que le acuidadosamente todas

las consignas de seguridad y de funcionamiento del aparato antes de usarlo. Conserve las instrucciones de

seguridad y de funcionamiento para que pueda consultarlas posteriormente. Respete todas las consignas

indicadas en la documentación, relacionadas con el producto y este documento.

• CUIDADO: Para prevenir cualquier riesgo de choque eléctrico y de incendio, no exponga este aparato a

la lluvia, a la humedad ni a fuentes de calorintensas.

• INSTALACIÓN: Cerciórese de que haya una circulación de aire suciente para evitar cualquier

sobrecalentamiento al interior del aparato. No coloque el aparato cerca ni sobre una supercie textil que

pudiera obstruir los oricios de ventilación. No instale el aparato cerca de fuentes de calor como radiador

o boca de aire caliente, ni en un lugar expuesto a los rayos solares directos o al polvo excesivo, a las

vibraciones o a los choques mecánicos. Esto podría provocar su mal funcionamiento o un accidente.

• ALIMENTACIÓN: Ponga a funcionar el aparato únicamente con la fuente de alimentación que se indica

en el aparato. Los aparatos deben estar conectados obligatoriamente a una fuente equipada con una

puesta a tierra ecaz. Por ningún motivo este enlace de tierra deberá ser modicado, cambiado o

suprimido.

• CABLE DE ALIMENTACIÓN: Los equipos incluyan interruptor general de alimentación (Encender I /

Apagar 0), la puesta en marcha o desconexión se realiza por medio de este interruptor.

El cable de alimentación constituye el único medio de desconectar el aparato totalmente de la red eléctrica.

Para estar seguro de que el aparato no está más alimentado, este cable debe de ser desconectado de la

toma de corriente.

Aplicar las siguientes consignas:

- El material conectado a residencia a la red informática, debe de tener un dispositivo de seccionamiento

fácilmente accesible que debe de ser incorporado al exterior del aparato.

- Desconectar el aparato del enchufe mural si no piensa utilizarlo durante varios días.

- Para desconectar el cable, tire de la clavija. No tire nunca del cable propiamente dicho.

- El enchufe de alimentación debe estar cerca del aparato y ser de fácil acceso.

- No deje caer el cable de alimentación ni coloque objetos pesados encima de él.

Si el cable de alimentación sufriera algún daño, ponga el aparato inmediatamente fuera de tensión. Es

peligroso hacer funcionar este aparato con un cable averiado, ya que un cable dañado puede provocar un

incendio o un choque eléctrico. Verique el estado del cable de alimentación de vez en cuando. Póngase

en contacto con su distribuidor o con el servicio de posventa si necesita cambiarlo.

• CONEXIONES: Todas las entradas y salidas (excepto la entrada del sector) son de tipo TBTS (Muy Baja

Tensión de Seguridad) denidas según EN 60950

• REPARACIÓN Y MANTENIMIENTO: Por ningún motivo, el usuario deberá tratar de efectuar operaciones

de reparación, ya que si abre los aparatos retirando el capó o cualquier otra pieza que forma parte de

las cajas o si destornilla los tornillos aparentes exteriores, existe el riesgo de producirse una explosión,

choques eléctricos o cualquier otro incidente. Contacte el servicio de posventa, a su distribuidor o dirigirse

con personal cualicado únicamente.

• ABERTURAS Y ORIFICIOS: Los aparatos pueden contener aberturas (aireación, ranuras, etc.). No

introduzca allí ningún objeto ni obstruya nunca estas aberturas. Si un líquido o un objeto penetra al

interior del aparato, desconéctelo y hágalo revisar por personal cualicado antes de ponerlo nuevamente

en servicio.

INSTRUCCIONES DE SEGURIDAD

9

2-3. RACKMOUNT INFORMATION

2-2. UNPACKING AND INSPECTION

1 x Smart MatriX LE (SMX100)

1 x Power supply cord.

2 x DVI male to HD15 female and DVI-D female

Breakout Cable

1 x HD15 to 5 BNC cable

1 x Ethernet cross cable (for device update)

1 x Set of 3 audio 5 pin screw terminals

1 x RCS - Remote Control Software (PC only) *

1 x User manual (PDF version) *

1 x Quick Start Guide *

* Download on our website: www.analogway.com/

2-4. CABLE AND ADAPTOR INFORMATION

A large choice of cables and adaptors are compatible with the Smart MatriX LE. To nd which are to be used

in your setup, please refer to the Hardware Specications chapter. Please contact your distributor for a list of

available cables and connectors for your Smart MatriX LE.

!

Tabletop mounting: The Smart MatriX LE can be used directly on a table, the unit is equipped with 4 handy

anti-slip rubber feet.

Rack mounting: The Smart MatriX LE is compatible with a 19” enclosure. Please follow the instructions

below to install the device in a 19” rack.

Place the device in your rack. Attach the device to the rack by using 4 screws through the front panel holes

(screws not included).

Rear xing is also recommended, in particular for permanent installations. The Smart MatriX LE is equipped

with drill holes designed for compatibility with most rackmount braces.

Connect all of the cables of the device and attach them to the rack with the help of tie wraps.

IMPORTANT:

- The openings in the side and rear panels of the device are for cooling. Do not cover these openings to

avoid cutting air circulation.

- Be sure that no weight in excess of 2 kg (4.4 Lbs.) is added onto the Smart MatriX LE.

- The maximum ambient operating temperature should not exceed 40°C (104°F).

- The rack and all mounted equipment in it must be reliably grounded according to national and/or local

electrical standards.

Dismantling front handles of the device could invalidate warranty on after sales services of your

Smart MatriX LE. It is strongly advised to avoid using front handles as rests for your Smart

MatriX LE, they are designed for manipulation purposes only.

If required, front handles of the device can be dismantled, but with caution.The original screws removed

must not be reintroduced to their location without handles in place. Substancial damages can occur,

including risk of electric shock from the main voltage. Only M4x12mm screws can be used. They are

supplied with the unit.

10

WARNING !

If required, front handles of the device can be dismantled,

but with caution.

The original screws removed must not be reintroduced to

their location without handles in place.

Substantial damages can occur, including risk of elec-

tric shock from the mains voltage.

Only M4x12mm screws can be used.

(They are supplied with the unit)

2-5. HARDWARE SPECIFICATIONS

Description of the input formats supported by the device.

• SDTV

• EDTV

• HDTV (RGB or YUV)

Standard Size Frame Frequency Line Frequency

NTSC 525/480i 59.94Hz / 60Hz 15.735 KHz

PAL 625/576i 50Hz 15.625 KHz

SECAM 625/576i 50Hz 15.625 KHz

Standard Size Frame Frequency Line Frequency

480p 525/480i 59.94Hz / 60Hz 31.47 KHz

576p 625/576i 50Hz 31.25 KHz

Standard Size Frame Frequency Standard

720p 1280x720 50Hz / 59.94Hz / 60Hz SMPTE 296M

1035i 1920x1035 59.94Hz / 60Hz SMPTE 260M

1080i 1920x1080 50Hz / 59.94Hz / 60Hz SMPTE 274M

1080p 1920x1080 23.97Hz / 24Hz / 25Hz / 29.97Hz / 30Hz SMPTE 274M

1080sF 1920x1080 50Hz / 59.94Hz / 60Hz SMPTE 274M

1080p 1920x1080 50Hz / 60Hz HDTV

• INPUT FEATURES

Inputs Signal Connector EDID

1 HD15#1 YES

2 Analog SDTV HD15#2 YES

3 Analog EDTV HD15#3 NO

4 Analog HDTV HD15#4 NO

5 Analog Computer DVI#1: ANALOG PART NO

6 DVI#2: ANALOG PART NO

7 Digital EDTV

Digital HDTV

Digital Computer

DVI#1: DIGITAL PART YES

8 DVI#2: DIGITAL PART YES

9

3G / HD / SD-SDI

BNC#1 NO

10 BNC#2 NO

11

• EDID

SETTINGS AND INPUT FUNCTIONS

The EDID is available on inputs #1 & #2 and #7 & #8. The user can modify the EDID choosing from a list of

predened formats and frequencies.

Analog DVI-D SDI

Settings / Functions 1 2 3 4 5 6 7 8 9 10 11 12

Auto Settings

YES YES YES YES YES YES YES YES N/A N/A N/A N/A

Auto Framing

YES

1

YES

1

YES

1

YES

1

YES

1

YES

1

NO NO NO NO NO NO

Blanking Settings

YES YES YES YES YES YES NO NO NO NO NO NO

Cropping

YES YES YES YES YES YES YES YES YES YES YES YES

Optimization

YES

1

YES

1

YES

1

YES

1

YES

1

YES

1

NO NO NO NO NO NO

Under/Overscan

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

YES

2

Aspect Ratio Settings

YES YES YES YES YES YES YES YES YES YES YES YES

Aspect Input Output

YES YES YES YES YES YES YES YES YES YES YES YES

Color Settings

YES YES YES YES YES YES YES YES YES YES YES YES

Advanced settings

YES YES YES YES YES YES NO NO NO NO NO NO

2:2 Pulldown

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

YES

3

3:2 Pulldown

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

YES

4

1/ Analog Computer Input or Analog Video Input (EDTV or HDTV only) 2/ Only Vidéo Input

3/ Only interlaced 50 Hz 4/ Only interlaced 59.94 Hz to 60 Hz

• COMPUTER FORMATS

Format Size Reduced Blankings Subsampling

VGA 640x480

800x480 800x480

SVGA 800x600

WVGA 848x480

XGA 1024x768

1152x864 1152x864

1280x600 1280x600

720p RGB 1280x720

WXGA 1280x768

800p RGB 1280x800

960p RGB 1280x960

SXGA 1280x1024

SWXGA 1360x768

1360x1024 1360x1024

1366x768 1366x768

DILA4/3 1364x1024

SWXGA+ 1366x800

SXGA+ 1400x1050

900p RGB 1440x900

1600x900 1600x900

UXGA 1600x1200

WSXGA+ 1680x1050

1080p RGB 1920x1080 YES

WUXGA 1920x1200 YES

1920x1440 1920x1440 YES

2K 2048x1080 YES

QXGA 2048x1536 YES

The Smart MatriX LE recognizes the following computer formats (Subsampled formats will be displayed with

a degraded quality. For a pixel clock > 165 MHz).

12

Input specications

• ANALOG COMPUTER

Connectors: Inputs #1 to #4: female HD15. Inputs #5 & #6: female DVI-I

(analog pins).

Line frequency: Up to 130 kHz (165 MHz Max pixel rate).

Resolution: Up to 1600x1200 @ 165Mhz, 1920x1200px

(RB, Max V size: 1200px, Max H size 2048px).

Sync. types: RGBHV, RGB/S, RGsB (Sync On Green).

Levels: R, G, B = 0.7 Vp/p.

H & V Sync = TTL.

Composite Sync = TTL and 0.3 V (negative).

SOG (Sync On Green) = 0.3 V.

Impedance: R, G, B = 75 ohms.

H = 75 ohms or Hi-Z.

V = Hi-Z.

• RGB/S - RGsB VIDEO

Connectors: Inputs #1 to #4: female HD15. Inputs #5 & #6: female DVI-I (analog pins).

Frequency: 15.625 kHz - 50 Hz (625 lines).

15.734 kHz - 60 Hz (525 lines).

Levels: R, G, B = 0.7 Vp/p.

SYNC. = 0.3 Vp/p or TTL (negative).

Impedance: RGB = 75 ohms.

SYNC. = 75 ohms or Hi-Z.

• COMPONENT

Connectors: Inputs #1 to #4: female HD15. Inputs #5 & #6: female DVI-I (analog pins).

Frequency: 15.625 kHz - 50 Hz (625 lines).

15.734 kHz - 60 Hz (525 lines).

Levels: Y = 1 Vp/p (0.7 V Luma + 0.3 V Sync.).

Cr / Pr & Cb / Pb = 0.7 Vp/p.

Impedance: 75 ohms.

• HDTV - HD-YUV

Connectors: Inputs #1 to #4: female HD15. Inputs #5 & #6: female DVI-I

(analog pins).

Formats: 720p/576p (60Hz), 1080i (50/60Hz), EDTV.

Levels: Y = 1 Vp/p (0.7 V + sync.).

Cr / Pr & Cb / Pb = 1 Vp/p (0.7 V + sync.).

Sync.: Tri-level: ±0.3V (positive/negative).

Bi-level: 0.3V (negative).

Impedance: 75 ohms.

or

13

or

• S.VIDEO

Connectors: Inputs #1 to #4: female HD15. Inputs #5 & #6: female DVI-I

(analog pins).

Standard: PAL/SECAM: 15.625 kHz - 50Hz - 625 lines.

NTSC (3.58 - 4.43 MHz): 15.734 kHz/60Hz/525 lines.

Levels: Y = 1 Vp/p (0.7 V Luma + 0.3 V Sync.).

C = 0.3 Vp/p (Chroma Burst).

Impedance: 75 ohms.

• COMPOSITE VIDEO

Connectors: Inputs #1 to #4: female HD15. Inputs #5 & #6: female DVI-I

(analog pins).

RCA.Standard: PAL / SECAM: 15.625 kHz - 50 Hz - 625 lines.

NTSC (3.58 - 4.43 MHz) : 15.734 kHz/60 Hz/525 lines.

Level: 1 Vp/p (0.7 V Luma + 0.3 V Sync.).

Impedance: 75 ohms.

• DVI (Digital Video Interface)

Connector: DVI Inputs #1 & #2: female DVI-I (digital pins).

Line frequency: Up to 130 kHz (165 MHz Max pixel rate).

Format: Digital Visual Interface (DVI)-TMDS single link.

Resolution: Up to 1600x1200 @ 165Mhz, 1920x1200px

(RB, Max V size: 1200px, Max H size 2048px).

• SD-SDI

Connector: SDI Inputs #1 to #2: female BNC.

Formats: SMPTE 259M-C.

Data rate: 270 Mbps serial digital.

Impedance: 75 ohms.

• HD-SDI

Connector: SDI Inputs #1 to #2: female BNC.

Formats: 720p @ 50 / 59.94 & 60 Hz.

1035i @ 50 / 59.94 & 60 Hz.

1080i @ 50 / 59.94 & 60 Hz.

1080p @ 23.97 / 24 / 25 / 29.97 / 30 / 50 / 59.94 & 60 Hz.

1080sF @ 50 / 59.94 & 60 Hz.

Data rate: 1.5 Gbps serial digital - SMPTE 292M (Level A).

2.97 Gbps serial digital - SMPTE 425M (Level A).

Impedance: 75 ohms.

14

• AUDIO

Input# Stereo Balanced Audio Connector

1

YES

YES Connectors Phoenix 5 pins

2

3

4

5

6

7

8

9

Non applicable (Embedded Audio SDI) Non applicable (Embedded Audio SDI)

10

AUX

YES Connectors Phoenix 5 pins

or

• ANALOG OUTPUTS

Connector: Outputs #1 & #2: female HD15, DVI-I (analog pins).

Resolutions:

Signals: RGBHV, RGBS and RGsB.

Levels: R, G, B = 0.7 Vp/p.

Sync. : Separate H & V = TTL (negative).

Composite = TTL (negative).

SOG = 0.3 Vp/p (negative).

Impedance: R, G, B = 75 ohms.

Output specications

FORMAT RATIO AVAILABLE REFRESH RATES

640 x 480 4 : 3 50Hz 60Hz 72Hz 75Hz

800 x 600 4 : 3 50Hz 60Hz 72Hz 75Hz

848 x 480 16 : 9 50Hz 60Hz 72Hz 75Hz

1024 x 768 4 : 3 50Hz 60Hz 72Hz 75Hz

1280 x 720 16 : 9 50Hz 60Hz

1280 x 768 15 : 9 50Hz 60Hz 72Hz 75Hz

1280 x 800 16 : 10 50Hz 60Hz 72Hz 75Hz

1280 x 1024 5 : 4 50Hz 60Hz 72Hz 75Hz

1360 x 768 16 : 9 50Hz 60Hz 72Hz 75Hz

1366 x 800 15 : 9 50Hz 60Hz 72Hz 75Hz

1400 x 1050 4 : 3 50Hz 60Hz 72Hz 75Hz

1440 x 900 16 : 10 50Hz 60Hz 72Hz 75Hz

1600 x 1200 4 : 3 50Hz 60Hz

1680 x 1050 16 : 10 50Hz 60Hz

1920 x 1080 16 : 9 50Hz 60Hz 72Hz 75Hz

1920 x 1080 B 16 : 9 50Hz 60Hz

1920 x 1200 16 : 10 50Hz 60Hz

2048 x 1080 19 : 10 50Hz 60Hz

or

15

• Connector: Balanced or unbalanced mono/stereo inputs

(all pin MCO male connector).

8 audio stereo inputs + 1 auxiliary.

Input #1 to #6: Unbalanced.

Aux. & input #7: Balanced.

Adjustable Level per input.

Vi = +15dBV max.

Zi = 40Kohms (Balanced).

L+

L-

R+

R-

UNBALANCED

LEFT

RIGHT

GROUND

4

MCO male connectors

Inputs #1 to #6: Balanced & unbalanced connection

Inputs DVI #1 to DVI #2: Balanced & unbalanced

connection

Input AUX: Balanced & unbalanced connection

AUDIO SETTINGS

Settings Availability

GAIN

YES: from -

∞

to + 18dB

Balanced Audio YES: Left and Right

• DVI (Digital Video Interface) OUTPUTS

Connector: Outputs #1 & #2: female DVI-I (digital pins).

Signal: Digital Visual Interface (DVI)-TMDS single link.

Resolutions:

FORMAT RATIO REFRESH RATE

640 x 480 4 : 3 50Hz 60Hz 72Hz 75Hz

800 x 600 4 : 3 50Hz 60Hz 72Hz 75Hz

848 x 480 16 : 9 50Hz 60Hz 72Hz 75Hz

1024 x 768 4 : 3 50Hz 60Hz 72Hz 75Hz

1280 x 720 16 : 9 50Hz 60Hz

1280 x 768 15 : 9 50Hz 60Hz 72Hz 75Hz

1280 x 800 16 : 10 50Hz 60Hz 72Hz 75Hz

1280 x 1024 5 : 4 50Hz 60Hz 72Hz 75Hz

1360 x 768 16 : 9 50Hz 60Hz 72Hz 75Hz

1366 x 800 15 : 9 50Hz 60Hz 72Hz 75Hz

1400 x 1050 4 : 3 50Hz 60Hz 72Hz 75Hz

1440 x 900 16 : 10 50Hz 60Hz 72Hz 75Hz

1600 x 1200 4 : 3 50Hz 60Hz

1680 x 1050 16 : 10 50Hz 60Hz

1920 x 1080 16 : 9 50Hz 60Hz 72Hz 75Hz

1920 x 1080 B 16 : 9 50Hz 60Hz

1920 x 1200 16 : 10 50Hz 60Hz

2048 x 1080 19 : 10 50Hz 60Hz

• AUDIO OUTPUT & OUTPUT #2

Connector: Output #1: Unbalanced

mono/stereo outputs (on 5-pin MCO male connector).

Vo max: Unbalanced = +15dBu (at 300Ω load).

Zo = 300Ω unbalanced.

G = 0 dB nominal.

16

Dimensions: W 480 x D 330 x H 44 mm

19”W x 13.8”D x 1.74”H

Weight: 4.5 kg / 11 lbs

(Compatible with a Standard 19” rack, Height = 1 U)

Cooling air ow from right side to left side.

Max ambient operating temperature: < 40°C (< 104°F).

Operating temperature: 0 to 40°C / +32°F to +104°F

Storage temperature: -40 to +70°C / -40°F to +158°F

Operating humidity: 10 to 80% (non condensing)

Input voltage range: 100-240 V, 50/60 Hz

Typical consumption: 140 W

CE Compliancy, test following:

- EN 55022: 2006 / A1: 2007,

- EN 55024: 1998 / A1: 2001 / A2: 2003,

- EN 61000-3-2: 2006,

- EN 61000-3-3: 1995 / A1: 2001 / A2: 2005

Safety, test following:

- IEC 60950-1: 2005,

- UL 60950-1: 2007,

- CAN/CSA-C22.2 NO. 60950-1

Power supply: IEC/EN/UL/CSA 60950-1, internal, autoswitching

Mechanical (in carton): Vibration: IEC60068-2-64

Free fall: IEC60068-2-32

RoHS, WEEE

Environmental specications

• COMMUNICATION PORTS

REMOTE RS-232

Connector: DB 9 female

Protocol: RS232

Data Rate: 9600 Bauds, 8 data bits, 1 stop bit, no parity bit,

no ow control by default.

DTR & RTS needed for upgrade.

• LAN

Connector: RJ45

Protocol: TCP (Transmission Control Protocol) or

UDP (User Datagram Protocol).

Ethernet: Base 10/100

Communication specications

17

Pin outs

• VGA

STANDARD VGA

1- Red 6- Red Return 11- ID Bit 0

2- Green 7- Green Return 12- ID Bit 1

3- Blue 8- Blue Return 13- H Sync

4- ID Bit 2 9- No Pin 14- V Sync

5- Test (Gnd) 10- Sync Return 15- ID Bit 3

• DIGITAL VISUAL INTERFACE DVI

1- TMDS Data 2- 7- DDC Data 13- Not used 19- TMDS Data 0 Shield

2- TMDS Data 2+ 8- Analog Vertical Sync 14- +5V (Power) 20- Not used

3- TMDS Data 2 Shield 9- TMDS Data 1- 15- Ground for (+5V) 21- Not used

4- Not used 10- TMDS Data 1+ 16- Hot Plug Detect. 22- TMDS Clock Shield

5- Not used 11- TMDS Data 1 Shield 17- TMDS Data 0- 23- TMDS Clock +

6- DDC Clock 12- Not used 18- TMDS Data 0+ 24- TMDS Clock-

C1- Analog Red Video (or Cr/Pr or C)

C2- Analog Green Video (or Y or Composite Video)

C3- Analog Blue Video (or Cb/Pb)

C4- Analog Horizontal Sync (or Composite Sync)

C5- Analog Common Ground Return

DDC = Display Data Chanel

TMDS = Transition Minimized differencial signal

• RS 232 CONNECTOR

1- NC 6- NC

2- Transmit data to PC (Tx1) 7- NC

3- Transmit data from PC (Rx1) 8- NC (or +12V. dc)

4- Receive data from display unit (Rx2) 9- Transmit data to display unit (Tx2)

5- Ground

• VESA DDC

1- Red 7- Green Return 13- H Sync

2- Green 8- Blue Return 14- V Sync

3- Blue 9- DDC+5 Volt supply 15- Data Clock (SCL)

4- ID Bit 2 0 10- Sync Return

5- Test 11- ID Bit

6- Red Return 12- Bi-directional data (SDA)

18

If you want to use HDCP content from your sources, be sure pluging HDCP compliant screens or projectors.

If it’s not the case, the output image could be disabled.

When displayingHDCP protected sources on non HDCP compliant equipment, the following message will be

displayed on the device VFD screen:

“Due to HDCP content, non HDCP screens cannot display protected sources”

Screen will go to black without displaying the HDCP input image, or partially layer out non HDCP content.

Concerning the DVI inputs, a specic feature allows enable/disable the HDCP receiver for the input chosen.

It can be very useful especially using a Mac:

Input Menu > DVI# > HDCP detection

The output status can provide you all information about the output in real time.

This feature is particularly needed when HDCP is used with long cable to be sure that the communication is

well handled.

HDCP compliance

NOTE : as part of our policy of continuous improvement, Analog Way reserves the right to make

design and specication changes for product improvements without prior notice. The performance

specication gures indicated are nominal values of production units. There may be some

deviations from these values in individual units.

!

19

La pagina sta caricando ...

Analog way Smart MatriX LE Manuale utente

Questo manuale è adatto anche per

Analog way Smart MatriX LE Manuale utente

in altre lingue

Documenti correlati

Altri documenti