Ohaus AX124 Manuale utente

Adventurer

TM

Balances

Instruction Manual

ADVENTURER BALANCES EN-1

TABLE OF CONTENTS

1. INTRODUCTION ....................................................................................................................3

1.1 Description ................................................................................................................................................... 3

1.2 Features ....................................................................................................................................................... 3

1.3 Definition of Signal Warnings and Symbols ................................................................................................. 3

1.4 Safety Precautions ....................................................................................................................................... 3

2. INSTALLATION .....................................................................................................................4

2.1 Unpacking .................................................................................................................................................... 4

2.2 Selecting the Location .................................................................................................................................. 4

2.3 Leveling the Equipment ................................................................................................................................ 4

2.4 Connecting Power ........................................................................................................................................ 5

2.5 Connecting the Interface .............................................................................................................................. 5

2.6 Initial Calibration ........................................................................................................................................... 5

3. OPERATION ..........................................................................................................................6

3.1 Overview of Display, Home Screen ............................................................................................................. 6

3.2 Principal Functions and Main Menu ............................................................................................................ 7

3.3 Overview of Parts and Features – Draft Shield Models ............................................................................... 8

3.4 Overview of Parts and Features – Non Draft Shield Models ....................................................................... 8

4. APPLICATIONS .....................................................................................................................9

4.1 Weighing ...................................................................................................................................................... 9

4.1.1 Item Settings .......................................................................................................................................... 10

4.1.2 Sample Name ......................................................................................................................................... 11

4.1.3 Save to USB ........................................................................................................................................... 11

4.2 Parts Counting............................................................................................................................................ 11

4.2.1 Item Settings .......................................................................................................................................... 12

4.3 Percent Weighing ....................................................................................................................................... 14

4.3.1 Item Settings .......................................................................................................................................... 14

4.4 Dynamic Weighing ..................................................................................................................................... 15

4.4.1 Item Settings .......................................................................................................................................... 15

4.5 Density Determination ................................................................................................................................ 16

4.5.1 Measuring the Density of a Solid Using Water (default) ........................................................................ 16

4.5.2 Measuring the Density of a Buoyant Material Using Water ................................................................... 17

4.5.3 Measuring the Density of a Solid Using an Auxiliary Liquid ................................................................... 17

4.5.4 Measuring the Density of a liquid using a Calibrated Sinker (not supplied) ........................................... 18

4.5.5 Measuring the Density of Porous Material Using Oil ............................................................................. 19

4.6 Check Weighing ......................................................................................................................................... 22

4.6.1 Item Settings .......................................................................................................................................... 22

4.7 Display Hold ............................................................................................................................................... 23

4.7.1 Display Hold ........................................................................................................................................... 23

4.7.2 Peak Hold ............................................................................................................................................... 23

4.7.3 Item Settings .......................................................................................................................................... 24

4.8 Totalization ................................................................................................................................................. 24

4.9 Formulation ................................................................................................................................................ 25

4.9.1 Item Settings .......................................................................................................................................... 25

4.10 Additional Features .................................................................................................................................... 26

4.10.1 Weigh Below .......................................................................................................................................... 26

5. MENU SETTINGS ................................................................................................................ 27

5.1 Menu Navigation ........................................................................................................................................ 27

5.1.1 Changing Settings .................................................................................................................................. 28

5.2 Calibration .................................................................................................................................................. 29

5.2.1 Calibration sub-menu (InCal models) ..................................................................................................... 29

5.2.2 Internal Calibration ................................................................................................................................. 29

5.2.3 Automatic Calibration ............................................................................................................................. 29

5.2.4 AutoCal™ Adjustment ............................................................................................................................ 30

5.2.5 Span Calibration ..................................................................................................................................... 30

5.2.6 Linearity Calibration................................................................................................................................ 31

5.2.7 Calibration Test ...................................................................................................................................... 31

5.3 Balance Setup ............................................................................................................................................ 31

5.3.1 Balance Set-up sub-menu ...................................................................................................................... 31

5.3.2 Language ............................................................................................................................................... 31

5.3.3 User Setting ............................................................................................................................................ 32

EN-2 ADVENTURER BALANCES

5.3.4 Filter Level .............................................................................................................................................. 32

5.3.5 Auto Zero Tracking ................................................................................................................................. 32

5.3.6 Auto Tare ................................................................................................................................................ 32

5.3.7 Graduations ............................................................................................................................................ 32

5.3.8 Date & Time ........................................................................................................................................... 33

5.3.9 Approved Mode ...................................................................................................................................... 33

5.4 Weighing Units ........................................................................................................................................... 34

5.4.1 Units Sub-menu ...................................................................................................................................... 34

5.5 Data Maintenance ...................................................................................................................................... 34

5.5.1 Data Maintenance sub-menu ..................................................................................................................... 34

5.6 Communication .......................................................................................................................................... 35

5.6.1 Communication Sub-menu ..................................................................................................................... 35

5.6.2 Baud Rate .............................................................................................................................................. 35

5.6.3 Transmission .......................................................................................................................................... 36

5.6.4 Handshake ............................................................................................................................................. 36

5.6.5 Print Output ............................................................................................................................................ 36

5.6.6 Auto Print ................................................................................................................................................ 36

5.6.7 Print Content .......................................................................................................................................... 36

5.6.8 Feed.. ..................................................................................................................................................... 36

5.6.9 Format.. .................................................................................................................................................. 36

5.6.10 Print Calibration Data.. ........................................................................................................................... 36

5.7 GLP and GMP Data ................................................................................................................................... 38

5.7.1 GLP Data Sub-menu .............................................................................................................................. 38

5.7.2 Header .................................................................................................................................................... 38

5.7.3 Balance Name ........................................................................................................................................ 38

5.7.4 User Name ............................................................................................................................................. 38

5.7.5 Project Name .......................................................................................................................................... 38

5.8 Factory Reset ............................................................................................................................................. 38

5.9 Lockout ....................................................................................................................................................... 38

6. LEGAL FOR TRADE (LFT) .................................................................................................. 39

6.1 Settings ...................................................................................................................................................... 39

6.2 Verification .................................................................................................................................................. 39

6.3 Sealing ....................................................................................................................................................... 39

7. PRINTING ............................................................................................................................ 40

7.1 Connecting, Configuring and Testing the Printer/Computer Interface ....................................................... 40

7.2 Output Format ............................................................................................................................................ 40

7.3 Printout Examples ...................................................................................................................................... 41

8. MAINTENANCE ................................................................................................................... 44

8.1 Calibration .................................................................................................................................................. 44

8.2 Cleaning ..................................................................................................................................................... 44

8.3 Troubleshooting ......................................................................................................................................... 44

8.4 Service Information .................................................................................................................................... 44

9. TECHNICAL DATA .............................................................................................................. 45

9.1 Specifications ............................................................................................................................................. 45

9.2 Drawings and Dimensions ......................................................................................................................... 54

9.3 Parts and Accessories ............................................................................................................................... 54

9.4 Communication .......................................................................................................................................... 55

9.4.1 Interface Commands .............................................................................................................................. 55

9.4.2 RS232 (DB9) Pin Connections ............................................................................................................... 56

9.5 The USB Interface ...................................................................................................................................... 56

10. SOFTWARE UPDATES ....................................................................................................... 57

11. COMPLIANCE...................................................................................................................... 58

ADVENTURER BALANCES EN-3

1. INTRODUCTION

1.1 Description

The Adventurer balance is a precision weighing instrument that will provide you with years of service if properly

cared for. The Ohaus Adventurer balances are available in capacities from 120 grams to 8,200 grams.

1.2 Features

Touch Controls: Quick, graphical access to all control

functions, over a dozen applications and many features.

1.3 Definition of Signal Warnings and Symbols

Safety notes are marked with signal words and warning symbols. These show safety issues and warnings. Ignoring

the safety notes may lead to personal injury, damage to the instrument, malfunctions and false results.

Signal Words

WARNING For a hazardous situation with medium risk, possibly resulting in injuries or death if not

avoided.

CAUTION For a hazardous situation with low risk, resulting in damage to the device or

the property or in loss of data, or injuries if not avoided.

Attention For important information about the product

Note For useful information about the product

Warning Symbols

General Hazard Electrical Shock Hazard



1.4 Safety Precautions

CAUTION: Read all safety warnings before installing, making connections, or servicing this

equipment. Failure to comply with these warnings could result in personal injury and/or

property damage. Retain all instructions for future reference.

 Verify that the AC adapter’s input voltage range and plug type are compatible with the local AC power

to be used.

 Make sure that the power cord does not pose a potential obstacle or tripping hazard.

 The balance is for indoor use only.

 Use the balance only in dry locations.

 Do not drop loads on the pan.

 Use only approved accessories and peripherals.

 Operate the equipment only under ambient conditions specified in these instructions.

 Disconnect the equipment from the power supply when cleaning.

 Do not operate the equipment in hazardous or unstable environments.

 Service should only be performed by authorized personnel.

 Do not position the balance such that it is difficult to reach the power connection.

Direct current

Alternating current

EN-4 ADVENTURER BALANCES

2. INSTALLATION

2.1 Unpacking

Carefully remove your Adventurer balance and each of its components from the package. The included

components vary depending on the balance model (see table below). Save the packaging to ensure safe storage

and transport. Please read the manual completely before installing and using the Adventurer balance to avoid

incorrect operation.

Included Components

 Balance

 Power Adapter

 Wind Ring (only for 0.1 mg and 1 mg models)

 Warranty Card

 Software Compact Disk

2.2 Selecting the Location

Avoid excessive vibrations, heat sources, air current, or rapid temperature changes. Allow sufficient space.

2.3 Leveling the Equipment

The Adventurer has a level bubble in a small round window beside the display.

To level the balance, adjust the 4 Leveling Feet until the bubble is centered in the

circle. See the Level Assist section below on information about how and which feet to

turn. Be sure the equipment is level each time its location is changed.

Level Assist

A level assist function is available to help leveling the Adventurer. There are two ways to access the function:

1. Weighing Application -> Item Settings -> Level Assist. See section 4.1.1 for more information.

2. Main Menu -> Balance Setup -> User Settings -> Level Assist. See section 5.3.3 for more information.

Rotate the feet according to the image above depending on the location of the level bubble until the bubble is

centered.

ADVENTURER BALANCES EN-5

2.4 Connecting Power

Connect the DC output connector to the power receptacle on the rear of the balance. Then connect the AC power

cord to a suitable electrical outlet.

CAUTION: For use with CSA certified (or equivalent approved) power source,

which must have a limited current output.

Attention: For optimal weighing performance, allow the balance to warm up for 60 minutes

prior to use.

2.5 Connecting the Interface

Use the built-in RS-232 Port to connect either to a computer or a printer with a standard (straight-through)

serial cable. Or connect using the scale’s USB port.

Interface connections on the rear of the balance: USB connection on the front of the balance:

.

USB1: Used to connect to PC only

USB2: Used to connect a USB flash driver only

RS232: Used to connect to PC or Printer

Note: For configuration and interface commands, see the Communication Menu Settings section.

For Connecting, Configuring and Testing the Printer/Computer Interface, and for sample Print Output Formats,

see the Printing section.

2.6 Initial Calibration

When the Balance is first installed, and when it is moved to another location, it must be calibrated to ensure

accurate weighing results. Most Adventurer Balances have built in AutoCal which can calibrate the balance

automatically and does not require calibration masses. If preferred, the balance can be manually calibrated with

external masses. Have the appropriate calibration masses available before beginning calibration. Refer to the

Calibration Section for masses and calibration procedure.

¤ AutoCal™

Fully automatic internal calibration system that assists with routine maintenance by automatically calibrating the

balance daily is available on most models.

Automatically calibrates the system when it senses a temperature change sufficient enough to affect weighing

accuracy (>1.5°C), or every 11 hours.

¤ External Calibration

Select precision models feature traditional external calibration in which external weights (user’s choice of calibration

weight values) are used to calibrate the balance to ensure accuracy.

USB1

RS232

USB2

EN-6 ADVENTURER BALANCES

3. OPERATION

3.1 Overview of Display, Home Screen

This equipment utilizes a touch-sensitive display with Touch areas and Buttons to control the equipment’s functions.

CONTROLS

Button

Action

Short Press (if powered Off): Turns on the scale

Long Press (if powered On): Turns off the scale

Note:

The balance will automatically power on when power is connected.

Short Press: Prints the present data to a printer or a computer.

Short Press: Perform Zero operation

Short Press: Perform Calibration operation

Short Press: Perform Tare operation

Main Application Screen

Application

Instructional Messages

Stability (*), Net (NET),

Gross (G) and/or center

of zero (>0<) indicators

Reference Fields

Application Buttons:

Functions vary by

application

Result Field: Information

varies by application

Touch g to change unit

Capacity and readability

ADVENTURER BALANCES EN-7

3.2 Principal Functions and Main Menu

Weighing: Press Zero to set the display to zero. Place an item on the pan. Display indicates gross weight.

Taring: With no load on the pan, press Zero to set the display to zero. Place an empty container on the pan

and press Tare. Add material to the container and its net weight is displayed. Remove container and

container’s weight appears as a negative number. Press Tare to clear.

Zero: Press Zero to zero the balance

MENU & SCREEN NAVIGATION

Touch Menu to open the menu list.

Calibration:

Touch to view calibration options.

Balance Setup:

Touch to view and change balance settings.

Weighing Units:

Touch to view and change weighing units.

Data Maintenance:

Touch to view data maintenance settings.

GLP and GMP Data:

Insert user data for traceability.

Factory Reset:

Touch to do a Factory reset of menu

settings.

Communication:

Touch to view COM Device Settings and

Print Settings.

Lockout:

Touch to view lockout options.

EN-8 ADVENTURER BALANCES

3.3 Overview of Parts and Features – Draft Shield Models

3.4 Overview of Parts and Features – Non Draft Shield Models

USB Host

USB Device

Power Input

RS232

LFT Switch

Adjustable Foot

Level Indicator

USB Host

Adjustable Foot

USB Device

LFT Switch

RS232

Power Input

Pan

Adjustable Foot

Pan

Wing Ring

Adjustable Foot

ADVENTURER BALANCES EN-9

4. APPLICATIONS

The balance can be configured to operate in various Application modes.

Touch the top left Application field (weighing in the example below):

The Adventurer Balance has 9 application modes, as follows:

Weighing

Parts Counting

Percent

Weighing

Dynamic

(Animal)

Weighing

Density

Determination

Check

Weighing

Display Hold

Totalization

Formulation

4.1 Weighing

Note: Before using any application, be sure the balance has been leveled and calibrated.

Use this application to determine the weight of items in the selected unit of measure.

Weighing

1. In the upper left portion of the home screen, select Weighing (this application is the default).

2. Press Tare or Zero if necessary to begin.

3. Place objects on the pan to display the weight. When stable, the * appears.

4. The resulting value is displayed in the main Display Line in the active unit of measure.

The WEIGHING Home screen

Main Display Line

Reference Fields

Application Buttons

Application Icon

Touch g to change unit

EN-10 ADVENTURER BALANCES

4.1.1 Item Settings

To view or adjust the current settings

Touch the

Item Settings

button. The Settings screen appears.

Minimum Weight: establish a minimum weight value to

be used to verify a reading. If an actual weight is below

the established Minimum Weight value, it is flagged by

a color change: yellow.

To adjust the Minimum Weight value, touch the

Minimum Weight

button.

A numeric input window appears.

Use the keys to enter the desired Minimum Weight,

then press Save.

The display reverts to the previous screen.

To return to the Weighing home screen, touch

Exit at the bottom of that screen.

Capacity Bar: When set to ON, a capacity bar is

displayed in the reference field. The capacity guide will

show the current weight as a percentage of balance

capacity.

If Capacity Bar is set to OFF, the reference field will

show Minimum Weight and Sample Name.

Weighing Units: Change the displayed unit. See

section 5.4 for more information

Note: Touching the weighing unit from application

home screen will also open the Weighing Units screen.

Filter Level: Change Filtering level. See section 5.3.4

for more information

GLP & GMP Data: See section 5.7 for more

information

Print settings: Change printing settings. See section 7

for more information.

Level Assist: Instructions on how to move the balance

feet to level the balance.

ADVENTURER BALANCES EN-11

4.1.2 Sample Name

Press this button to add a sample name. An alphanumeric input window appears. Press to alternate

between Lower and Upper case characters.

Lower Case: Upper Case:

Key in the desired sample name and press Save to save the name and return to weighing home screen.

4.1.3 Save to USB

Insert the USB flash drive into the USB slot located on the front of the balance. Next, press the Save to

USB button to save the data to the USB flash drive. Once saved, the button will momentarily change color

to orange.

Notes: The first time a USB flash drive is connected to the balance there might be some delay time

before the button Save to USB works. This is due to that the balance is creating the necessary

folders on the USB flash drive where the data will be stored.

The Density Determination and Check Weighing applications do not have a Save to USB button.

CAUTION:

The weighing data will be saved to USB every day. However, if different weighing modes are used the

data will be separately saved to individual files.

Depending on the USB drive used, all data might not be transferred from the balance or the display

might freeze. If this happens, unplug the USB flash drive and try another USB flash drive.

Ohaus takes no responsibility if data on USB flash drive is erased or if the USB flash drive breaks while

it is connected to the balance.

To minimize the risk of problems arising, Ohaus suggests using a high quality USB flash drive.

4.2 Parts Counting

Note: Before using any application, be sure the balance has been leveled and calibrated.

Use this application to count samples of uniform weight.

Parts Counting

1. In the upper left portion of the home screen, select Parts Counting

2. Press Tare or Zero if necessary to begin.

3. Place objects on the pan to display the weight. When stable, the * appears.

4. The resulting value is displayed in the main Display Line in pieces (PCS).

The Parts Counting Home screen

Main Display Line

Reference Fields

Application Buttons

Application

Icon

EN-12 ADVENTURER BALANCES

4.2.1 Item Settings

To view or adjust the current settings

Touch the

Item Settings

button. The Settings screen appears.

Samples: The sample size can be 1 to 10 000 pieces.

The default sample size is 10. Once a sample size is

changed, the balance will immediately open the

recalculate APW screen, expecting to establish a new

APW.

To adjust the sample size, touch the

Samples

button.

A numeric input window appears.

Use the keys to enter the desired sample size,

then press Save.

The next screen appears, with the message to place

the reference weight on the pan.

Place the reference weight on the pan, then touch

Accept to capture the value, the screen shows number

of pcs.

Establish an Average Piece Weight (APW):

Each time a new type of part is counted, the

nominal weight of one piece (Average Piece

Weight or APW) must be established using a

small quantity of pieces. This APW is stored

until replaced by another APW.

There are two methods to establish the APW

value:

1. The actual APW is known

2. The APW must be derived by weight. For

this case the current sample size will be used

ADVENTURER BALANCES EN-13

Set a known Average Piece Weight (APW)

To adjust the APW value directly, touch the

APW

button.

A numeric input window appears.

Key in the desired APW Weight, then press Save.

The display returns to the application home screen with the

new APW value in the reference field.

Set a new Average Piece Weight (APW) – Derived

To establish a new APW, place the reference weight on the pan

and press Accept to continue.

Note: The sample size that is displayed will be used.

To use a different sample size, change that first. (See above.)

The home screen shows the number of pieces at the new APW

Auto Optimization: When set to On, improves counting accuracy by re-calculating the piece weight

automatically as parts are added. Default is Off.

Notes:

APW Optimization occurs only when the number of pieces added to the pan is between one and three times the

number already on the pan.

If the APW is entered manually by the numeric keypad, APW auto optimization will not occur.

Print settings: Change printing settings. See section 7 for more information.

Note: The Save to USB button will only appear after a USB flash drive has been connected to the balance.

See section 4.1.3 for more information.

EN-14 ADVENTURER BALANCES

4.3 Percent Weighing

Note: Before using any application, be sure the balance has been leveled and calibrated.

Use Percent Weighing to measure the weight of a sample displayed as a percentage of a pre-established

reference weight.

The default (or last) reference weight is displayed.

Percent Weighing

1. In the upper left portion of the home screen, select Percent Weighing.

2. Place an object on the pan. The difference between the sample and the reference weight is displayed as a

percentage.

The Percent Weighing Home screen

Main Display Line

Reference Fields

Application Buttons

Application

Icon

4.3.1 Item Settings

To view or adjust the current settings

Touch the

Item Settings

button. The Settings screen

appears.

Recalculate Ref. Wgt: To establish a new

reference weight value, touch the recalculate

reference weight button.

Follow the screen instructions to establish a new

reference weight.

Alternatively, press the

Ref. Weight

button from

the Percent Weighing Recalculate Ref. Wgt

screen to establish a new reference weight

manually through a numerical keypad.

Print settings: Change printing settings. See section 7

for more information.

Note: The Save to USB button will only appear after a

USB flash drive has been connected to the balance.

See section 4.1.3 for more information.

ADVENTURER BALANCES EN-15

4.4 Dynamic Weighing

Note: Before using any application, be sure the balance has been leveled and calibrated.

Use this application to weigh an unstable load, such as a moving animal. Two different start/reset modes can be

selected: Manual (start and stop via key press) and Automatic (start and stop automatically).

Dynamic Weighing – Manual (default)

1. In the upper left portion of the home screen, select Dynamic Weighing

2. Place objects on the pan and press the Start button.

The Dynamic Weighing Home screen

Main Display Line

Reference Fields

Application Buttons

Application

Icon

3. The balance begins a countdown (averaging process). During the countdown, the information line

displays the time remaining.

If necessary, press Stop to quit.

4. When the countdown ends, the result line is displayed and held. Press Clear to clear the held weight and

return to the initial screen.

Note: Clear the pan before beginning a new Dynamic weighing cycle.

4.4.1 Item Settings

To view or adjust the current settings

Touch the

Item Settings

button. The Settings screen

appears.

Averaging Time: Set the averaging time to a value

between 1 and 99 seconds. Default is 5 seconds.

Automatic Mode: When set to On, the cycle begins

when an object is placed on the pan, and the held value

is automatically reset when the object is removed from

the pan.

Sample Name: Assign a name to the sample.

Print settings: Change printing settings. See section 7

for more information.

Note: The Save to USB button will only appear after a

USB flash drive has been connected to the balance.

See section 4.1.3 for more information.

EN-16 ADVENTURER BALANCES

4.5 Density Determination

Note: Before using any application, be sure the balance has been leveled and calibrated.

Use this application to determine an object’s density. Four types of density determination can be made:

1. Solids more dense than water

2. Solid less dense than water

3. Liquid density

4. Porous material (impregnated with oil)

The Density Determination Home screen

Main Display Line

Reference Fields

Function Buttons

Application

Icon

4.5.1 Measuring the Density of a Solid Using Water (default)

Press the Item Settings button to open the Density

Determination Settings screen.

Confirm the following Setups are selected:

 Density Type: Solid

 Auxiliary Liquid: Water

 Porous Material: Off

To adjust the water temperature value,

touch the Water Temp. button.

The balance calculates water density based on the water

temperature value entered.

Measure the actual water temperature using a precision

thermometer.

A numeric input window appears.

Enter the actual water temperature, then press Save.

To return to the Density Determination home screen,

touch Back.

Step 1 of 2 –

Weigh the

Sample in Air.

Press

Start

.

Follow screen

instructions,

then press

Accept

to store the dry

sample weight

(“in air”).

ADVENTURER BALANCES EN-17

Step 2 of 2 –

Weigh the

Sample

Submerged in

the Liquid.

Follow the

screen

instructions,

then press

Accept

to store the

sample weight

(submerged

in liquid).

Once the necessary weights have been determined, the density of the sample is displayed in g/cm

3

(along with the weight in air, weight in water) on the Application screen.

Press

Start

to reset all the weight values and restart the process.

4.5.2 Measuring the Density of a Buoyant Material Using Water

Press the Item Settings button to open Settings screen.

Confirm the following Setups are selected:

 Density Type: Solid

 Liquid Type: Water

 Porous Material: Off

Press

Back

to return to the Density Determination home

screen.

Follow the same procedure as Solid Material above, except

in Density Determination step 2, push the sample down

into the liquid until it is fully submerged.

4.5.3 Measuring the Density of a Solid Using an Auxiliary Liquid

To enable this feature, enter the Density Determination Setup menu and select the following:

Density Type: Solid; Liquid Type: Other; Porous Material: Off.

Confirm the default values displayed (Liquid Density, etc) are

correct.

To adjust the Liquid Density value, touch the Auxiliary liquid

button and select Other.

A numeric input window appears.

Key in the density in g/cm

3

, then press Save.

The display returns to the previous screen.

To return to the Density Determination home screen,

touch Back.

Begin the Density determination process as per above.

EN-18 ADVENTURER BALANCES

4.5.4 Measuring the Density of a liquid using a Calibrated Sinker (not supplied)

To enable this feature, enter the Density Setup menu and select the following; Density Type: Liquid.

Note: when the Density Type is set to Liquid, the Liquid type and Porous material selections are disabled.

The DENSITY DETERMINATION – LIQUID Home screen

Main Display Line

Reference Fields

Function Buttons

Application Icon

Confirm that the default value displayed (sinker volume) is

correct. To edit the default values, touch

Sinker Volume

.

To adjust the Sinker volume value, touch the

Sinker Volume

button.

A numeric input window is displayed.

Key in the desired value, then press Save.

The display returns to the previous screen with the new value

highlighted.

To return to the Density Determination home screen,

touch Back.

Press

Start

to start the process.

Step 1 of 2 – Weigh the Sinker in Air.

Follow the screen instructions, then press

Accept

to store the sinker weight (“in air”).

La pagina sta caricando ...

Ohaus AX124 Manuale utente

Ohaus AX124 Manuale utente

in altre lingue

Documenti correlati

Altri documenti