MTD H 15 Original Operating Instructions

jqa=mêçÇìÅíë=^âíáÉåÖÉëÉääëÅÜ~Ñí=√=p~~êÄêΩÅâÉå=√=dÉêã~åó

H15

FORM NO. 769-10094A

English . . . . . . . . . . . . . . . . . . . . . . . 4

(Original operating instructions)

Français . . . . . . . . . . . . . . . . . . . . . . 14

(Notice d’instructions d’origine)

Deutsch . . . . . . . . . . . . . . . . . . . . . . . 26

(Originalbetriebsanleitung)

Nederlands . . . . . . . . . . . . . . . . . . . . 37

(Originele gebruiksaanwijzing)

Italiano . . . . . . . . . . . . . . . . . . . . . . . 48

(Istruzioni per l’uso originali)

Español . . . . . . . . . . . . . . . . . . . . . . . 59

(Instrucciones de funcionamiento originales)

Svenska . . . . . . . . . . . . . . . . . . . . . . 70

(Originalbruksanvisning)

Dansk . . . . . . . . . . . . . . . . . . . . . . . . 80

(Originale driftsvejledning)

Norsk . . . . . . . . . . . . . . . . . . . . . . . . 90

(Originale driftsanvisningen)

Suomi . . . . . . . . . . . . . . . . . . . . . . . . 100

(Alkuperäinen käyttöohjekirja)

English Operating manual

4

Contents

Safe operating practices . . . . . . 4

Operating and display

elements . . . . . . . . . . . . . . . . . . 7

Installation manual . . . . . . . . . . . 7

Oil and petrol . . . . . . . . . . . . . . . 8

Operating . . . . . . . . . . . . . . . . . . 9

Maintenance and cleaning . . . . 10

Transportation . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . 13

Details on the rating plate

Enter all information on the rating

plate of your unit in the following

field. You can find the rating plate

near the engine.

These specifications are very

important for subsequent identi-

fication when ordering spare

parts and for customer service.

These and other details for your

appliance can be found on the

separate CE declaration of confor-

mity that forms an integral part

of these operating instructions.

Illustrations

Fold out the illustrated pages at the

start of the operating manual.

Graphical representations may

deviate in detail from the pur-

chased unit.

Safe operating practices

Using the unit correctly

This unit is designed exclusivly

– for use around the outside

of the house and in the garden

– for trimming lawn edges and small

or inaccessible areas of grass

(e.g. under bushes),

– for cutting wild growth, shrubs and

undergrowth,

– according to the descriptions and

safety instructions indicated in this

operating manual.

Any other use is not as intended.

Improper use is not covered by the

warranty and the manufacturer will

reject any liability.

The user is liable

for all injuries to third parties and

damage to their property.

Operate the unit only in the techni-

cal condition as stipulated and

delivered by the manufacturer.

Arbitrary changes to the unit will

exclude the manufacturer from any

liability for resulting injury and/or

damage.

Read all instructions before

operating

 Please read these instructions

carefully. Familiarise yourself

with the operation and handling

of the unit.

 Do not use this unit if you are

tired or ill or under the influence

of alcohol, drugs or medication.

 Do not permit persons under the

age of 16 to handle this unit or

perform other work on the unit,

such as maintenance, cleaning

or adjusting (local regulations

may specify the minimum age

of the user).

 This unit is not designed to be

used by persons (including

children) who have limited physi-

cal, sensory or mental abilities

or who have no experience and/

or knowledge of the unit, unless

they are supervised by a person

responsible for their safety

or they have been instructed by

the person how to use the unit.

 Children should be supervised

to ensure that they do not play

with the appliance.

 Check the unit before using it.

Replace damaged parts.

Check whether fuel is leaking

out. Ensure that all connections

are attached and tight.

Replace cutting attachment parts

which are cracked, flawed

or damaged in any other way.

Ensure that the cutting attach-

ment has been installed correctly

and attached securely.

Ensure that the guard for the

cutting attachment has been

attached correctly and is in the

recommended position.

If these instructions are not

followed, the user and bystan-

ders may be injured or the unit

damaged.

 Use only original replacement

lines which have a diameter

of 3.0 mm. Never use a metal-

reinforced string, wire, chain,

rope, etc.. These may break

off and become dangerous

projectiles.

 Always be aware of the risk of

injury to head, hands and feet.

 Depress the throttle.

It must automatically return

to the home position.

Perform all settings and/or

repairs before operating the unit.

 Before using the unit, always

clear the area which you want to

trim. Remove all objects such as

stones, broken glass, nails, wire

or string which could be ejected

or become entangled in the

cutting attachment.

Remove children, bystanders

and animals from the area.

Keep children, bystanders and

animals at a minimum distance

of 15 m; there is still a risk

of bystanders being hit by ejec-

ted objects. Bystanders should

wear eye protection. If somebody

approaches, immediately switch

off the engine and cutting attach-

ment.

Safety instructions

for petrol-driven units

Petrol is highly flammable and

the vapours may explode if ignited.

Take the following precautions:

 Store petrol in designated and

permitted containers only.

 Keep ignition sources away from

spilled petrol. Do not start the

engine until the petrol vapours

have evaporated.

 Before filling the tank, always

switch off the engine and leave

it to cool down.

Never remove the tank cap or fill

the tank while the engine is hot.

Before using the unit, ensure

that the tank cap is screwed

on tightly. Slowly unscrew the

tank cap to reduce the pressure

in the tank gradually.

Operating manual English

5

 Mix petrol and fill the tank

in a clean, well ventilated outdoor

area only where there are no

sparks or flames.

After switching off the engine,

slowly unscrew the tank cap.

Do not smoke while mixing petrol

or filling the tank. Immediately

wipe any spilled petrol off the

unit.

 Before switching on the engine,

carry the unit at least 10 m away

from the filling station.

While filling the tank or using

the unit, do not smoke and keep

sparks and naked flames out

of the area.

 Replace damaged exhausts,

fuel tanks, or filler caps.

Operating the unit

 Never start the unit and never

leave it running in a closed

room or building. The inhalation

of exhaust gases may be fatal.

Use the unit outdoors only.

 Wear eye and ear protection

when using the unit.

If working in a dusty environ-

ment, wear a face or dust mask.

A long-sleeved shirt is recom-

mended.

 Wear thick, long trousers, boots

and gloves.

Do not wear loose clothing,

jewellery, short trousers, sandals

and do not walk barefoot.

Pin your hair above your shoul-

ders. If required, wear a hair net.

 The cutting attachment cover

must always be attached when

you use the unit as a lawn

trimmer. Both trim lines must

be pulled out and the correct line

must be installed.

The trim line must not be pulled

out over the end of the cover.

 The unit has a clutch.

The cutting attachment stops

when the unit is running at no

load. If it does not stop, have

the unit adjusted by a mechanic

at your authorised dealer.

 Before switching on the unit,

ensure that line spool/cutting

blade cannot strike an object.

 Adjust the handle bar to your

height so that the you have

the unit under control.

 Operate the unit in daylight or

adequate artificial lighting only.

 Avoid starting the unit uninten-

tionally. Be ready to operate

the unit when you pull the starter

rope. User and unit must be in

a stable position when the unit

is started. Follow the Start/Stop

instructions.

 Use this unit for its designated

purpose only.

 Do not stretch too far over

the unit. Always have a secure

footing and keep your balance.

 When operating the unit, always

hold the unit firmly with both

hands. Always hold both sides

of the handle bar firmly.

 When operating the unit, always

wear the shoulder belt.

 Do not use the unit in adverse

weather conditions, e.g. if there

is a probability of rain or a storm.

 Never change the engine

settings preset at the factory.

 Keep away from naked flames,

avoid creating sparks and do not

smoke.

 Never operate the unit with

a defective ignition switch.

 Keep your hands, face and feet

away from all moving parts.

Do not touch the cutting attach-

ment while it is rotating and

do not attempt to stop it.



Do not touch the engine or

muffler. These parts become very

hot while the unit is being used.

They remain hot for a short time

even when the unit is switched

off.

 Do not let the engine run quicker

than required for cutting

or trimming of lawn edges.

Do not run the engine at high

speed when it is not cutting.

 Always switch off the engine

if you cannot start cutting

immediately or if you are moving

from one place to another.

 If unusual vibrations occur,

switch off the engine immedia-

tely. Check the unit for damage.

If the unit is damaged, contact

a specialist workshop.

 If you strike or ensnare a foreign

object, immediately switch

off the engine and check whether

the unit has been damaged.

Never use the unit with loose

or damaged parts.

 Before removing blockages

or performing other work on the

unit, switch off the engine and

remove the spark-plug terminal.

 Stop and switch the engine off

before performing maintenance

or repairs or before changing

cutting attachments.

Also pull out the spark-plug

terminal.

 Use only original spare parts

for repairs.

These parts can be purchased

from your authorised dealer.

 Never use parts, accessories

or attachments which are not

authorised for this unit.

Otherwise, the user may be

seriously injured and the unit

damaged. In addition, your

warranty may be deemed null

and void.

 Keep the unit clean and ensure

that there are no plants or other

objects caught between the

cutting attachment and guard.

 To reduce the risk of fire, please

replace damaged mufflers and

spark extinguishers and remove

grass, leaves, excess lubricants

and layers of soot from the

engine and muffler.

 Have all repairs carried out

by a specialist workshop only.

Working with the cutting

blade (depending on model)

 Before operating the unit, please

read all safety instructions

carefully.

 Always keep the handle bar

between the user and cutting

attachment.

 Never cut material if the cutting

blade is 75 cm or higher above

ground level.

English Operating manual

6

 The unit may recoil if the rotating

blade strikes an object which

cannot be cut immediately.

Recoils may be strong enough

to throw the unit and/or user

in any direction and may cause

the user to lose control of the

unit. Recoils may occur without

warning if the blade gets caught,

jams or locks. This can easily

happen in areas in which the

material to be cut is difficult

to see.

 Never use the undergrowth blade

to cut undergrowth thicker than

12.7 mm. Otherwise, violent

recoils may occur.

 When using the cutting blade,

the cutting attachment cover

must always be attached.

 Do not attempt to touch or stop

the blade while it is rotating.

 A rotating blade may cause

injuries, even when the engine

has been switched off or the

throttle has been released.

Hold the unit firmly until the blade

has come to a standstill.

 Do not run the engine at high

speed when it is not cutting.

 If you strike or ensnare a foreign

object, immediately switch

off the engine and check whether

the unit has been damaged.

Have the repair damaged before

continuing to use the unit.

Do not use the unit with a bent,

cracked or blunt blade.

Throw away bent, twisted,

cracked or broken blades.

 Do not sharpen the cutting blade.

The sharpened tip of the blade

may break off during operation.

This may result in serious

injuries. Replace the blade.

After operating the unit

 Clean the cutting blades with

a household detergent to remove

any remnants.

Lubricate the blade with machine

oil to prevent rust.

 Store and lock away the blade

securely to protect it from

damage and unauthorised use.

Other safety instructions

 As long as the tank still has petrol

in it, never store the unit in a buil-

ding where vapours could come

into contact with sparks or naked

flames.

 Leave the engine to cool down

before transporting or conveying

the unit. Attach the unit securely

for transportation.

 Empty the fuel tank before trans-

porting the unit.

 Store the unit in a dry condition,

locked away or high up to pre-

vent unauthorised use and

damage. Keep the unit away

from children.

 Never douse or splash the unit

with water or other liquids.

Keep the handle bar dry, clean

and dust-free.

Clean the unit after each use

and follow the instructions

for cleaning and storage.

 Dispose of waste petrol/oil

or any packaging remnants

in accordance with local

regulations.

 Keep this manual.

Read it frequently and use

it to instruct other users.

If you lend this unit to somebody

else, also include this manual.

Operating times

Observe the national/municipal

regulations concerning times

of use (if required, ask your local

authority).

Symbols on the appliance

This operating manual describes

safety and international symbols

and pictograms which may

be displayed on this unit.

Read this user handbook in order

to familiarise yourself with all

safety, installation, operating and

repair instructions.

Attention!

Before starting

up the unit, read

the operating

instructions!

Wear eye, hearing

and head protection.

While operating

this unit, wear heavy

duty boots and

protective gloves.

Keep third parties

away from the danger

area!

Ejected objects and

rotating parts may

cause serious injuries!

Risk of injury from

rotating parts!

Keep hands and feet

away from rotating

parts.

Beware of hot

surfaces!

Keep fire away from

the fuel tank!

Petrol/Oil!

Always use clean and

fresh lead-free petrol

for mixing petrol.

Use only authorised

oil according to the

operating manual

for mixing petrol.

Do not fill up with fuel

of specification E85!

Maximum rpm.

Do not let the unit

run more quickly than

the maximum rpm.

!

Operating manual English

7

Ignition switch

On /run/start

Ignition switch

Off/stop

Choke settings

Choke position

Operating position

Ensure that these symbols on the

unit are always in a legible state.

Symbols used in this manual

The following symbols are used

in this manual:

Danger

They refer to dangers which are

connected with the described

activity and which may result

in injury.

Caution

They refer to dangers which are

connected with the described

activity and which may result

in damage to property.

Note

Indicates important information and

application tips.

Operating and display

elements

Caution.

Damage to the appliance

This first describes the control and

display elements. Do not execute

any of the functions yet!

Fig. 1

1 Exhaust cover

2Spark plug

3 Starter handle

4 Tank cap

5 Intake pump/primer

6 Choke lever

7 Air filter cover

8 Handle bar

9 Upper drive shaft

10 Shaft coupling

11 Lower drive shaft

12 Cutting attachment cover

13 Line cutting blade

14 Line spool

15 Gearbox

16 Holder for cable harness

17 Throttle

18 Ignition switch

19 Throttle lock

20 Shoulder belt holder

21 Cutting blade with cutting

attachment cover *

22 Retaining bar *

23 Socket wrench *

24 Spacer for installation

of Trimmer-Plus accessory *

* depending on model

Installation manual

Danger

Risk of injury from engine being

started unintentionally.

Protect yourself from injury.

Before working on the engine:

– Switch off the engine.

– Wait until all moving parts have

come to standstill; the engine

must have cooled down.

– Remove spark-plug terminal.

Disposal instructions

Dispose of packaging remnants,

old units, etc., in accordance with

local regulations.

Installing and setting

the handle bar

Fig. 2a

 Remove the upper retaining plate

from the handle holder.

 Push cable harness holder onto

the right control handle.

 Insert right control handle into

the lower holder.

 Insert left control handle into

the lower holder.

 Attach upper retaining plate

and tighten the screws.

 Press cable harness into

the holders.

Installing/removing the lower

drive shaft

Fig. 2b

Installation

 Remove protective cap (optional)

from the shaft coupling and lower

drive shaft.

 Turn screw handle (1) on the shaft

coupling (2) anti-clockwise

to open the shaft coupling.

 Press release button (3)

on the lower drive shaft and push

the shaft into the shaft coupling

until the release button engages

in the retaining hole (4).

Note

If required, turn the lower drive

shaft slightly until the square shaft

and the holder of the upper drive

shaft mesh.

 Tighten screw handle (1)

on the shaft coupling clockwise.

Check that the lower drive shaft

is tight.

Removal

 Turn screw handle (1) on the shaft

coupling (2) anti-clockwise

to open the shaft coupling.

 Press release button (3) and

pull the lower drive shaft straight

out of the shaft coupling.

Adjusting the carrying

system (shoulder strap)

Fig. 3

 Place harness over your

shoulders.

 Close the catch on the abdominal

belt (1.). If required, readjust.

 Adjust abdominal belt

to the correct width (2.).

 Adjust shoulder belt

to the correct length (3.).

 Latch the hook of the carrying

system into the holder on the unit

(4.) and adjust the attachment

pad to a comfortable length (5.).

Note

Clip

A is used in an emergency

to release the appliance as quickly

as possible from the carrying

system.

To do this, pull the clip upwards.

English Operating manual

8

Attaching the cutting

attachment cover

Fig. 4

 Unscrew the screws (1) and

remove the clamp (2) from

the cutting attachment cover (3).

 Place cutting attachment cover

(3) on the lower drive shaft (4)

and attach the clamp (2) with

the screws (1).

Do not tighten the screws yet!

 Remove screw (5) from the gear-

box.

 Attach holder (6) to the gearbox

with the screw (5).

 Tighten the screws (1).

Attaching/removing

the line head

Attaching the line head

Fig. 5

 If attached, remove cutters

and blade attachment parts

beforehand. See Removing

the cutting blade.

 Push spacer (1) onto the drive

shaft (2). Align the 3 openings

in the spacer (3), the gearbox (4)

and the gear cover (5).

Note

If alignment is not correct, the line

head cannot be attached/removed!

 Insert retaining bar (6) through

the openings (3, 4, 5) in order

to secure the gearbox.

 While holding the retaining

bar (6), turn the line head (7)

anti-clockwise (to the left)

onto the drive shaft.

Tighten line head firmly!

Note

Ensure that the line head (7)

is seated correctly on the spacer

(1), i.e. centred and resting flat!

 Remove retaining bar from

the gear head.

Remove the line head

Fig. 6



Align the openings (3, 4, 5). Insert

retaining bar (6) through the

openings and hold in position.



Unscrew line head (7) clockwise

(to the right) off the drive shaft.

Attaching/removing the

cutting blade (depending

on model)

Attaching the cutting blade

Fig. 7

 If attached, remove the line head

beforehand. See Attaching/re-

moving the line head.

Note

When attaching the cutting blade

for the first time, remove the blade

attachment parts (blade holder (8),

retaining bell (9), nut (10))

if attached. See Removing

the cutting blade.

 Push spacer (1) onto the drive

shaft (2). Align the 3 openings

in the spacer (3), the gearbox (4)

and the gear cover (5) (Fig. 5).

Note

If alignment is not correct,

the cutting blade cannot

be attached/removed!

 Insert retaining bar (6) through

the openings (3, 4, 5) in order

to secure the gearbox.

 While holding the retaining bar

(6), attach the cutting blade (7)

with

blade holder (8), retaining

bell (9) and nut (10)

as follows:

– Push cutting blade (7) onto

drive shaft (2) and centre

on the spacer (1).

Note

Ensure that the cutting blade (7)

is seated correctly on the spacer

(1), i.e. centred and resting flat!

– Attach blade holder (8), retai-

ning bell (9) and nut (10).

Ensure that the blade holder is

seated correctly in the toothing!

– Tighten nut firmly anti-clock-

wise (to the left) – tightening

torque 37 Nm.

Note

– Before tightening, check again

that the cutting blade is seated

correctly.

– If you do not have a torque

wrench, tighten the nut firmly by

hand. Then tighten the nut anti-

clockwise (to the left) another

half turn using a ring spanner.

 Remove retaining bar from

the gear head.

 Remove guard (if fitted) from

the cutting blade.

Removing the cutting blade

Fig. 8



Attach guard (if available)

to the cutting blade.



Align the openings (3, 4, 5).

Insert retaining bar (6) through

the openings and hold in position.



Unscrew nut clockwise (to the

right).



Remove cutting blade (7), blade

holder (8) and retaining bell (9)

(Fig. 7).

Oil and petrol

Oil

Use quality oil only, API

classification TC (TSC-3) which

is offered for air-cooled two-stroke

engines.

Mix the oil for two-stroke engines

according to the instructions

on the container, 1:40 (2,5 %).

Petrol

Danger

Under certain conditions petrol

is extremely flammable and

explosive.

– Refuel only in a well ventilated

area and with the engine swit-

ched off. Do not smoke and

switch off all ignition sources

in the vicinity of the tank

or at the fuel storage depot.

– Do not overfill the fuel tank (there

must be no fuel in the inlet

nozzle). After filling up the tank,

ensure that the tank cap

is closed and secured.

– When filling up the tank,

do not spill any fuel.

Spilled fuel or petrol vapours may

ignite. If fuel has been spilled,

ensure that the area is dried

before the engine is restarted.

– Prevent repeated or prolonged

skin contact or inhalation

of the vapours.

!

Operating manual English

9

Caution

Do not fill up with fuel of speci-

fication E85. If fuel of specification

E85 (ethanol content >15 %) is

used, the engine may be damaged.

The use of an unauthorised fuel will

void the warranty.

See instructions on mixing

oil and petrol

Old and/or incorrectly mixed fuel

are the main reasons for the unit

not running properly.

Always use clean, fresh unleaded

petrol (no more than 60 days old,

minimum octane number 91 ROZ).

Follow exactly the instructions

for the correct petrol/oil mixture.

Correctly mix two-stroke engine oil

and lead-free petrol, 1:40 (2,5 %).

Do not mix directly in the tank.

Filling the tank

Fig. 1

 Remove tank cap (4).

 Fill fuel tank with petrol/oil

mixture. Never overfill!

 Close fuel tank tightly.

 Move the unit approx. 10 m from

the filling station/fuel container

before starting the engine.

Operating

Danger

Do not hook the shoulder strap onto

the unit until the engine has started.

 Mix petrol (gasoline) with oil.

Fill the tank with the mixture.

See Oil and petrol.

Starting the engine

Starting with a cold engine.

Fig. 9

 Press throttle lock (2) and press

the throttle (3) all the way and

hold in position.

Note

The throttle cannot be actuated until

the throttle lock has been pressed.



Move the ignition switch (1)

to the

I/

START

position.



Press the switch (4) down.

 Release throttle lock and throttle.

Note

Both levers remain locked in the

depressed position (cold start

position).

 Slowly and fully press intake

pump/primer (1) 6x (Fig. 10).

The fuel must be visible in the

pump. If this is not the case, keep

pressing until fuel is visible.

 Move choke lever (2) to position

(Fig. 10).

 Press the unit on the ground.

 Slowly pull on the starter cable

until it begins to resist.

Then pull quickly and forcefully

until the engine starts (Fig. 11).

After starting the engine, do not

let the pull-starter spring back,

but slowly guide it back.

 Leave the engine running

for approx. 1–2 minutes.

 Move choke lever (2) to position

(Fig. 10).

 Press throttle (3) and then

release to deactivate the cold

start lock (Fig. 9). The switch (4)

jumps automatically back to the

original position. The engine runs

at idling speed.

Note

The unit has warmed up adequa-

tely when the engine accelerates

without faltering.

Starting with a warm engine

 Move the ignition switch (1)

to the I/START position (Fig. 9).

 Move choke lever (2) to position

(Fig. 10).

 Press the unit on the ground.

 Slowly pull on the starter cable

until it begins to resist.

Then pull quickly and forcefully

until the engine starts (Fig. 11).

After starting the engine, do not

let the pull-starter spring back,

but slowly guide it back.

Note

If the engine does not start, move

the choke lever (2) to position .

When the engine has started,

move the choke lever (2) back

to position (Fig. 10).

Stopping the engine

Fig. 9

 Release throttle (3).

Leave the idling engine to cool

down.

 Move the ignition switch (1)

to the

0/STOP position.

Note

If the engine does not stop when

the ignition switch is actuated,

move the choke lever (2) to position

to force the engine to stop

(Fig. 10). Before using the unit

again, have the ignition switch

checked by a specialist workshop!

Holding the lawn trimmer

Before using the unit, place

yourself in the operating position

(Fig. 12). Check the following:

– The user is wearing eye protec-

tion and the correct clothing.

– The shoulder strap has been

set to the correct height.

– The handle bar has been set

in such a way that you can grip

it with both hands without having

to stretch out your arms.

– The unit is below waist height.

– Hold the cutting attachment

parallel to the ground so that

the vegetation to be cut can

easily be reached without the

user having to bend forward.

Setting the length

of the trimmer line

(depending on model)

You can release the trim line with

the bump knob cutting attachment

without stopping the engine.

To release more line, tap the

cutting attachment on the ground

(Fig. 13) while running the lawn

trimmer at a higher speed.

Note

The trim line should always

be at max. length.

The shorter the trim line becomes,

the more difficult it is to release.

Each time the head is bumped,

approx. 25 mm of cutting line are

released. A blade in the cutting

attachment cover cuts the line back

to the correct length if too much line

is released.

!

English Operating manual

10

It is best to bounce the bump head

on bare ground or hard earth.

If you attempt to release the trim

line in tall grass, the engine may

stall. Always keep the trim line fully

extended. The shorter the trim line

is, the more difficult it is to release.

Note

Do not run the bump head along

the ground.

The line may break by:

– becoming entangled with foreign

objects,

– normal material fatigue,

– attempting to cut thick-stalked

weeds,

– striking walls, garden fences, etc..

Tips for best trim results

– Keep the cutting attachment

parallel to the ground.

– Use only the tip of the line for

cutting, especially along walls.

If more than the tip is used for

cutting, the cutting capacity

is reduced and the engine may

overload.

– Cut grass which is taller than

20 cm from the top down in small

stages to prevent premature

wear of the line and engine

resistance.

– If possible, cut from left to right.

Cutting to the right improves

the cutting capacity of the unit.

Grass clippings are then ejected

by the user.

– Slowly move the lawn trimmer

at the required height in and

out of the cutting area.

Walk either forwards and back-

wards or from side to side.

Better results are achieved

by cutting shorter pieces.

– Cut dry grass and weeds only.

The service life of the cutting line

depends on the following:

– following of the previous cutting

tips,

– the vegetation which is to be cut,

– where it is cut.

For example, a line wears out

more quickly if it is cutting against

a house wall than around a tree.

Decorative cutting

You will receive a decorative cut if

you cut all vegetation around trees,

posts, fences, etc.

Rotate the whole unit until you

are holding the cutting attachment

at an angle of 30° to the ground

(Fig. 14).

Working with the cutting

blade (depending on model)

Before using the unit, place your-

self in the operating position

(Fig. 12). See Holding the lawn

trimmer.

Tips for working with the cutting

blade:

– Cut rhythmically.

– Stand firmly but comfortably

on the ground.

– Before you start cutting, set

the unit to full speed.

At full speed the blade has

maximum cutting force and will

therefore not jam so easily, stick

or cause blade impacts which

may result in serious injury

to the user or other persons.

– When cutting, move the upper

part of your body from right

to left.

– Always release the throttle and

reduce the engine to no load

when you are not cutting.

– Rotate the unit in the same

direction in which the blade

is cutting. This promotes cutting.

– Move one or two steps to the

next trimming area after swinging

back the unit and stand firmly

again.

Follow these instructions to prevent

vegetation from wrapping itself

around the blade:

– Cut at full speed.

– Swing from right to left into

the vegetation which

is to be cut (Fig. 15).

– When swinging back, avoid

vegetation which has just

been cut.

Using approved accessory

equipment from the

Trimmer-Plus range

Caution

Follow all instructions in the

manuals for the Trimmer-Plus

accessory equipment.

Notes

– Before installing the Trimmer-

Plus accessory equipment,

insert the spacer (24, Fig. 1)

into the shaft coupling (Fig. 30).

– The Trimmer-Plus accessory

equipment is installed/removed

in the same way as described

in the section Installing/

removing the lower drive shaft".

Maintenance and cleaning

Caution

Before working on the unit:

– Switch off the engine.

– Wait until all moving parts have

come to standstill; the engine

must have cooled down.

– Remove spark-plug terminal

from the engine to prevent

the engine from starting

unintentionally.

Have all repairs carried out

by a specialist workshop only.

At the end of the season have

the unit inspected and serviced

by a specialist workshop.

Do not splash the unit with water,

otherwise electric components may

be damaged. Clean the unit after

every use. Failure to clean the unit

can damage the materials and

cause malfunctions.

Installing the cutting line

(depending on model)

Always use a replacement cutting

line with a diameter of 3.0 mm.

If using a cutting line which has

a length other than the one indica-

ted, the engine may overheat

or misfire. There are two methods

of replacing the cutting line:

– Winding a new line onto

the spool

– Fitting a spool with a prewound

line

Operating manual English

11

Winding a new line onto

the spool

Fig. 16

 Press both retaining plates (1)

of the spool housing (2) and

remove the spool together

with spool cover (3).

Fig. 17

 Clean spool housing (1), spring

(2) and spool (3) together

with spool cover (4).

Use a clean cloth.

 Check the toothing (5) for wear

on the spool housing (1), the

spool (3) and on the spool cover

(4). If required, replace damaged

parts.

 Take approximately 3 metres

of new trim line and fold in half.

Note

Always use the specified line length!

The line may not be released

correctly if it is too long.

Fig. 18

 Insert the folded end of the trim

line into the retaining plate

of the spool.

 Wind the lines in tight, even

layers onto the lower and upper

halves of the spool.

Observe the winding direction

indicated on the spool!

Fig. 19

 Press the ends of the line into

the two opposing retaining slots.

Fig. 20

 Insert the spool into the spool

cover and feed the ends

of the line through the opposing

slots in the spool cover.

Fig. 21



Press pre-assembled unit (3) out

of the inner spool and spool cover

into the spool housing (2) until

the retaining plates (1) engage.

Fitting a spool with a prewound

line

Fig. 16

 Press both retaining plates (1)

of the spool housing (2) and

remove the spool together with

spool cover (3).

 Take spool out of the spool

cover.

Fig. 17

 Clean spool housing (1), spring

(2) and spool cover (4).

Use a clean cloth.

 Check the toothing (5) for wear

on the spool housing (1) and on

the spool cover (4). If required,

replace damaged parts.

Fig. 20

 Insert a new spool into the spool

cover and feed the ends of the

line through the opposing slots

in the spool cover.

Fig. 21

 Press pre-assembled unit (3)

out of the inner spool and spool

cover into the spool housing (2)

until the retaining plates (1)

engage.

Cleaning the air filter

Clean and lubricate the air filter

after every ten operating hours.

This is an important part of mainte-

nance. If the air filter is not serviced,

the warranty will be deemed

null

and void

.

Fig. 22

 Open air filter cover:

Press retaining plate (1) and

remove cover (2).

 Remove the air filter (3).

Fig. 23

 Wash the filter with detergent

and water. Flush out the filter

thoroughly, leave to drip and dry

completely.

Fig. 24

 Use adequately clean oil (SAE

30) to lubricate the filter easily.

Fig. 25

 Press on the filter to distribute

the oil and remove excess oil.

 Install filter.

 Attach air filter cover again,

ensuring that it engages.

Note

If the unit is used without the air

filter, the warranty will be voided.

Adjust carburettor

Fig. 26

The idle speed can be set with the

screw (1). This work may be carried

out by a specialist workshop only.

Replace petrol filter

(depending on model)

If required – This work may

be carried out by a specialist

workshop only.

Check/replace spark plug

Use only original spark plugs

or ones approved by the manu-

facturer.

The correct electrode gap

is

0.6–0.7 mm. Every 25 operating

hours take out the spark plug and

check its condition.

 Stop the engine and leave

it to cool down.

 Remove spark-plug terminal.

 Remove dirt from around

the spark plug.

 Unscrew spark plug to the left

with a spark plug wrench.

 Check/adjust the electrode

gap of

0.6–0.7 mm (Fig. 27).

Note

Replace a damaged, sooted

or dirty spark plug.

 Screw in spark plug and tighten

to a torque of 12.3–13.5 Nm.

Do not tighten too tightly.

Cleaning the exhaust

Fig. 28

Clean the area under the exhaust

cover (1) every 25 operating hours.

To do this, the exhaust cover must

be removed.

This work may be carried out

by a specialist workshop only.

Checking/topping up the

grease in the gearbox

Fig. 29

Check the level of grease in the

gearbox every 25 operating hours.

To do this, remove the screw (1).

If required, refill with a high-quality

lithium grease.

This work may be carried out

by a specialist workshop only.

English Operating manual

12

Cleaning the unit

Caution

Always keep the unit and venti-

lation slots clean and free of dirt.

Use a small brush for cleaning

the outside of the unit.

Do not use abrasive detergents.

Household cleaners which contain

aromatic oils such as pine oil

or lemon as well as solvents

such as kerosene may damage

the plastic housing and handle.

Wipe housing with a damp cloth

only.

Storage

 Never store the unit with fuel

in the tank or in a location where

petrol vapours may be ignited

by a spark or naked flame.

 Before storing the unit, leave

the engine to cool down.

 Store the unit in a dry, closed

room to prevent unauthorised

use or damage.

Keep the unit away from children.

Long-term storage

If the unit is to be stored for a pro-

longed period, proceed as follows:

 Drain all the fuel out of the tank

and pour into a container with

the same two-stroke mixture.

Do not use fuel which has been

stored for longer than 3 days.

 Start the engine and leave

running until it stops.

This ensures that there is no fuel

left in the carburettor.

 Leave the engine to cool down.

Take out the spark plug and pour

30 ml of a high-grade engine oil

or two-stroke oil into the cylinder.

Slowly pull the starter rope

to distribute the oil.

Reinstall the spark plug.

Note

Take out the spark plug and pour

all the oil out of the cylinder before

starting the unit after storage.

 Thoroughly clean the unit and

check for loose and damaged

parts.

Repair or replace damaged parts

and tighten loose screws, nuts

and bolts.

The unit can now be stored.

 Store the unit in a dry, closed

room to prevent unauthorised

use or damage.

Keep the unit away from children.

Transportation

 Before transporting the unit,

leave it to cool down.

 Empty the fuel tank before trans-

porting the unit.

Tank cap must be closed tightly.

 Secure the unit to prevent it from

shifting during transportation.

Warranty

The warranty regulations issued

by our company or the importer

are valid in all countries.

We shall repair any faults on your

unit free of charge in accordance

with the warranty, provided the fault

was due to defective materials

or manufacturing. If claiming under

the warranty, please contact your

seller or your nearest branch.

Operating manual English

13

Troubleshooting

If you have any further questions,

please contact your authorised

dealer on site.

Error Cause Remedial action

Engine does not start. Ignition switch set to 0/STOP. Set switch to I/START.

Fuel tank empty. Fill fuel tank.

Intake pump not pressed down

far enough.

Slowly press intake pump all the way down

10 times.

Engine flooded. Implement the starting process with

the choke lever in the operating position.

Old or incorrectly mixed fuel. Empty the tank/fill with fresh fuel mixture.

Dirty spark plug. Replace or clean spark plug.

Engine does not run constantly

at no load.

Air filter blocked. Clean or replace air filter.

Old or incorrectly mixed fuel. Empty the tank/fill with fresh fuel mixture.

Carburettor incorrectly adjusted. Have the carburettor adjusted

by a specialist workshop.

Petrol filter dirty. Have petrol filter replaced by a specialist

workshop.

Engine does not accelerate. Old or incorrectly mixed fuel. Empty the tank/fill with fresh fuel mixture.

Carburettor incorrectly adjusted. Have the carburettor adjusted

by a specialist workshop.

Strong vibrations. Damaged cutting tools or drive

parts.

Switch off the unit immediately.

Have defective parts replaced

by a specialist workshop.

Cutting head does release line. Cutting head entangled

with grass.

Stop the engine and clean the cutting

attachment.

No line in the cutting head. Wind up new line.

Spool jammed. Replace spool.

Cutting head dirty. Clean spool and spool housing.

Line fused together. Pull apart, take out the fused part and wind

up the line again.

Line twisted when wound up. Pull apart and wind up the line again.

Not enough line released. Tap the bump head and pull out the line

until 10 cm of line is outside the cutting

attachment.

Français Instructions de service

14

Sommaire

Pour votre sécurité . . . . . . . . . . 14

Éléments de commande

et d’affichage . . . . . . . . . . . . . . 18

Notice de montage . . . . . . . . . . 18

Huile et essence . . . . . . . . . . . 20

Service . . . . . . . . . . . . . . . . . . . 20

Maintenance et entretien . . . . . 22

Transport . . . . . . . . . . . . . . . . . 24

Garantie . . . . . . . . . . . . . . . . . . 24

Dépannage . . . . . . . . . . . . . . . 25

Indications sur la plaque

signalétique

Reportez dans l’encadré

ci-dessous toutes les indications

figurant sur la plaquette signalé-

tique de votre appareil.

Vous trouverez la plaquette

signalétique de cet appareil

à proximité du moteur.

Ces indications sont très importan-

tes car elles permettront ultérieure-

ment d’identifier et de commander

les pièces de rechange.

Le service après-vente a égale-

ment besoin de ces indications.

Vous trouverez ces indications

ainsi que d’autres sur l’appareil

dans la déclaration de conformité

CE, document séparé mais faisant

partie intégrante de la présente

notice d’instructions.

Illustrations

Dépliez les volets illustrés situés en

début de notice.

Dans le détail, les illustrations

graphiques peuvent différer

de l’appareil acheté.

Pour votre sécurité

Utilisation correcte

de l’appareil

Cet appareil est exclusivement

destiné à servir

– dans le domaine d’un jardin

domestique et jardin d’agrément,

– pour tondre les bords du gazon

ainsi que les surfaces gazonnées

de petite taille ou difficilement

accessibles (par exemple sous

les buissons),

– ainsi que pour tailler les plantes

sauvages, arbustives et les brous-

sailles,

– conformément aux descriptions

et consignes de sécurité figurant

dans la présente notice d’instruc-

tions.

Toute autre utilisation sera réputée

non conforme.

Toute utilisation non

conforme à l’usage prévu entra”ne

la perte du bénéfice de la garantie,

et le fabricant décline pour sa part

toute responsabilité.

L’utilisateur répond de tous les

dommages occasionnés à des tiers

et à leurs biens.

N’utilisez l’appareil que dans

l’état technique prescrit et livré

par le fabricant.

Toute modification arbitraire appor-

tée à l’appareil dégage le fabricant

de toute responsabilité envers

les dommages qui pourraient

en résulter.

Lire toutes les consignes

avant l’utilisation

 Veuillez lire ces consignes

attentivement et entièrement.

Familiarisez-vous avec l’utilisa-

tion et le maniement de l’appa-

reil.

 N’utilisez pas cet appareil si vous

êtes fatiguée ou malade, sous

l’empire d’alcool, de drogues,

ou sous l’effet de médicaments.

 Il est interdit aux personnes de

moins de 16 ans d’utiliser cet

appareil ou d’effectuer tous tra-

vaux dessus, dont par exemple

de maintenance, nettoyage,

réglage.

Des dispositions en vigueur

localement peuvent fixer

un âge minimum différent.

 Cet appareil n’est pas destiné

à l’usage par des personnes

(enfants compris) présentant des

aptitudes physiques, sensoriel-

les ou intellectuelles restreintes,

ou qui manquent de l’expérience

et / ou des connaissances

requises, sauf si elles sont

surveillées par une personne

chargée de leur sécurité,

ou si elles ont reçu de cette

dernière des instructions sur

la façon d’utiliser l’appareil.

 Il faudrait surveiller les enfants

pour être sûr qu’ils ne jouent

pas avec l’appareil.

 Examinez l’appareil avant de

l’utiliser. Remplacez les pièces

ab”mées. Vérifiez si du carburant

coule. Assurez-vous que tous

les éléments de liaison ont été

montés et fixés.

Remplacez les accessoires

de coupe qui se sont fissurés,

fêlés ou endommagés de quel-

que manière que ce soit.

Assurez-vous que l’accessoire

de coupe est correctement

incorporé et qu’il est bien fixé.

Assurez-vous que le couvercle

protégeant l’accessoire de coupe

ajouté est correctement fixé

et qu’il se trouve dans la position

recommandée.

Le non-respect de ces consignes

peut causer des blessures

à l’utilisateur et aux personnes

qui l’entourent, et endommager

l’appareil.

 Veuillez n’utilisez que des fils

de rechange d’origine présentant

un diamètre de 3,0 mm.

N’utilisez jamais de cordon

renforcé avec du fil métallique,

de fil métallique, cha”ne, câble

ou assimilé. Ils risqueraient

de se rompre et de devenir

des projectiles dangereux.

 Soyez en permanence conscient

du risque de blessures à la tête,

aux mains et aux pieds.

Instructions de service Français

15

 Appuyez sur la manette des gaz.

Elle doit automatiquement

revenir en position zéro.

Effectuez tous les réglages

ou réparations avant de vous

servir de l’appareil.

 Avant chaque utilisation, netto-

yez la zone sur laquelle vous

voulez couper les bordures.

Enlevez tous les objets tels que

les pierres, tessons de bouteilles,

clous, fils métalliques et mor-

ceaux de ficelles susceptibles

d’être catapultés ou de s’enche-

vêtrer dans l’accessoire

de coupe. Éloignez les enfants,

les badauds et les animaux

de la zone où vous travaillez.

Demandez aux deux premiers

de se tenir à une distance d’au

moins 15 mètres ; ils s’exposent

en effet à un risque résiduel

d’être atteints par les objets

catapultés. Les personnes vous

regardant devraient porter

des lunettes enveloppantes.

Si vous remarquez que

quelqu’un s’approche de vous,

éteignez immédiatement le mo-

teur et désactivez immédiate-

ment l’accessoire de coupe.

Consignes de sécurité pour

les appareils à moteur

à essence

L’essence s’enflamme avec une

facilité extrême.

Les vapeurs d’essence peuvent

littéralement exploser en s’enflam-

mant. Prenez par conséquent les

mesures de protection suivantes :



Ne rangez l’essence que dans

des bidons spécialement prévus

et homologués à cet effet.



Si de l’essence a été renversée,

ôtez-lui toute chance de s’enflam-

mer. Ne faites démarrer le moteur

qu’une fois que les vapeurs

d’essence se sont volatilisées.



Éteignez toujours le moteur

et laissez-lui toujours le temps

de refroidir avant de remplir

le réservoir.

N’enlevez jamais le bouchon

du réservoir d’essence et ne rem-

plissez jamais le réservoir tant

que le moteur est très chaud.

N’utilisez jamais l’appareil sans

avoir revissé le bouchon sur

le réservoir. Dévissez le bouchon

du réservoir lentement, pour

que la pression régnant dedans

diminue doucement.

 Mélangez et versez l’essence

dans un endroit propre et bien

aéré, où il n’y a aucun risque

de génération d’étincelles

ou de flammes. Ne dévissez

le bouchon du réservoir – lente-

ment – qu’après avoir éteint

le moteur. Interdiction de fumer

pendant que vous mélangez

de l’essence ou remplissez

le réservoir.

Si de l’essence a coulé sur

l’appareil, essuyez-le immédiate-

ment pour l’en débarrasser.

 Éloignez ensuite l’appareil

d’au moins 10 mètres du lieu

de remplissage avant de faire

démarrer le moteur.

Interdiction de fumer.

Pendant que vous remplissez

le réservoir avec de l’essence

ou utilisez l’appareil, veillez

à l’absence de toute source

d’étincelles et ou de flammes sur

la zone où vous vous trouvez.

 Remplacez le pot d’échappe-

ment, le réservoir ou le bouchon

du réservoir s’ils sont ab”més.

Pendant l’utilisation

 Si vous vous trouvez dans un

local ou un bâtiment fermés dans

les deux cas, ne faites jamais

démarrer l’appareil et ne le lais-

sez jamais marcher.

L’inhalation des gaz d’échappe-

ment peut être mortelle.

N’utilisez l’appareil qu’en plein

air.

 Portez des lunettes enveloppan-

tes et un casque anti-bruit lors-

que vous utilisez l’appareil.

Si vous travaillez dans un

environnement poussiéreux,

portez un masque de visage

ou un masque anti-poussière.

Le port d’une chemise à man-

ches longues est recommandé.

 Portez des pantalons longs

et épais, des bottes et des gants.

Ne portez pas de vêtements

flottants, de bijoux, shorts /

pantacourts, sandales, et n’uti-

lisez jamais l’appareil pieds nus.

Si vous portez-les cheveux

longs, rassemblez-les en chig-

non au dessus des épaules.

Portez le cas échéant un filet

à cheveux.

 Il faut que le capot de l’acces-

soire de coupe soit toujours fixé

lorsque vous utilisez l’appareil

comme coupe-herbe.

En service, les deux fils coupe-

herbe doivent se trouver

en position sortie et il faut avoir

installé le fil correct. Il ne faut

pas que le fil de coupe se trouve

tiré au-delà de l’extrémité

du couvercle.

 L’appareil présente un embra-

yage. Lorsque le moteur tourne

au ralenti, l’accessoire de coupe

ne tourne pas. S’il devait tourner

avec le moteur au ralenti, faites

vérifier l’appareil par un mécani-

cien de votre concessionnaire.

 Avant d’allumer l’appareil,

assurez-vous que la bobine

de fil / la lame de coupe n’entre

en contact avec aucun objet.

 Réglez le guidon sur votre taille

afin d’assurer une préhension

ferme de l’appareil.

 N’utilisez l’appareil que de jour

ou en présence d’un bon éclai-

rage artificiel.

 Évitez les démarrages du moteur

par inadvertance.

Lorsque vous tirez le cordon

du lanceur, soyez prêt à piloter

l’appareil. Au démarrage du mo-

teur, vous-même et l’appareil

devez vous tenir bien d’aplomb.

Veuillez tenir compte des instruc-

tions relatives au démarrage

et à l’arrêt.

 N’utilisez cet appareil que

conformément à sa destination.

 Ne vous mettez pas excessive-

ment en porte-à-faux.

Tenez-vous toujours bien

d’aplomb et maintenez

l’équilibre.

Français Instructions de service

16

 Pendant la marche de l’appareil,

tenez-le toujours fermement des

deux mains. Tenez toujours

le guidon des deux côtés.

 Pendant l’utilisation, portez

toujours la bandoulière.

 N’utilisez pas l’appareil par mau-

vais temps (p. ex. lorsqu’il

y a risque de pluie ou d’orage).

 Ne modifiez jamais les prérég-

lages du moteur effectués

en usine.

 Éloignez toute flamme nue,

ne provoquez pas d’étincelles

et ne fumez pas.

 N’utilisez jamais l’appareil

si son interrupteur d’allumage

est défectueux.

 Éloignez les mains, le visage

et les pieds de toutes les pièces

mobiles. Ne touchez pas l’acces-

soire de coupe tant qu’il tourne,

et ne tentez pas non plus

de le stopper.

 Ne touchez pas le moteur

et le silencieux.

Pendant l’utilisation, ces organes

deviennent très chauds.

Après avoir éteint le moteur,

ils demeurent encore très

chauds un peu de temps.

 Ne faites pas tourner le moteur

à un régime supérieur à celui

nécessaire pour tondre et couper

les bordures.

Ne faites pas tourner le moteur

à plein régime lorsque vous

ne tondez / coupez pas.

 Éteignez toujours le moteur lors-

que vous tardez à commencer

la tonte / coupe, ou lorsque vous

passez d’un endroit à traiter

au suivant.

 Si le moteur se met à vibrer

anormalement, éteignez-le

immédiatement.

Vérifiez si l’appareil s’est endom-

magé. Si c’est le cas, rendez-

vous dans un atelier spécialisé.

 Si l’accessoire de coupe percute

un corps étranger ou si ce corps

étranger s’enchevêtre dedans,

éteignez immédiatement le mo-

teur et vérifiez si cela a provoqué

des dégâts. N’utilisez jamais

l’appareil avec des pièces

mal fixées ou endommagées.

 Arrêtez toujours le moteur et dé-

branchez la cosse de la bougie

avant de supprimer les blocages

ou d’effectuer tous travaux sur

l’appareil.

 Avant d’effectuer une mainte-

nance, des réparations ou

de changer des accessoires

de coupe, arrêtez-vous et étei-

gnez le moteur.

Débranchez en plus la cosse

de la bougie.

 Pour réparer l’appareil, n’utilisez

que des pièces de rechange

d’origine. Vous pouvez vous

procurer ces pièces auprès

de votre concessionnaire.

 N’utilisez jamais des pièces

et accessoires divers qui n’ont

pas été homologués pour cet

appareil. Les conséquences

risquent d’être des blessures

graves pour l’utilisateur et un

endommagement de l’appareil.

En outre, le bénéfice de la

garantie est perdu en pareil cas.

 Maintenez l’appareil en parfait

état de propreté et veillez à ce

qu’aucune plante ou objet divers

ne se coince entre l’accessoire

de coupe et la tôle de protection.

 Pour réduire le risque de départ

de feu, veuillez s.v.p. remplacer

un silencieux ou un étouffeur

d’étincelles défectueux endom-

magé, enlevez l’herbe, les

feuilles, le lubrifiant en quantité

excessive et les couches

de suie présentes sur le moteur

et le silencieux.

 Veuillez confier l’ensemble

des réparations exclusivement

à un atelier spécialisé.

En cas de marche

avec la lame de coupe

(selon le modèle)

 Avant d’utiliser l’appareil, veuillez

lire les consignes de sécurité

attentivement et dans leur inté-

gralité.

 Veillez à ce que le guidon

se trouve toujours entre l’utilisa-

teur et l’accessoire de coupe.

 Lorsque vous utilisez une lame

de coupe, ne coupez JAMAIS

à une hauteur supérieure

à 75 cm.

 Des phénomènes de recul

peuvent se manifester lorsque la

lame en rotation percute un objet

impossible à trancher d’un coup.

Les réactions de recul peuvent

être suffisamment violentes pour

faire partir l’appareil et / ou son

utilisateur dans un direction quel-

conque et lui faire perdre

éventuellement le contrôle de

l’appareil. Les réactions de recul

peuvent se produire sans pré-

venir, lorsque la lame se plante

dans un objet, se coince ou se

bloque. Cela peut se produire

facilement dans des zones dans

lesquelles la visibilité sur les

matières à couper est mauvaise.

 Avec la lame à broussailles,

ne coupez aucun objet faisant

plus de 12,7 mm d’épaisseur.

Vous vous exposez sinon

à de violentes réactions de recul.

 Lorsque l’appareil sert équipé

de la lame de coupe, il faut tou-

jours que le capot de l’accessoire

de coupe soit monté.

 Ne tentez jamais de toucher

la lame ou de l’arrêter pendant

qu’elle tourne.



Une lame encore en train de tour-

ner peut provoquer des blessu-

res, même après avoir arrêté le

moteur ou relâché la manette des

gaz. Tenez l’appareil fermement

jusqu’à ce que la lame se soit

entièrement immobilisée.

 Ne faites pas tourner le moteur

à plein régime lorsque vous

ne tondez / coupez pas.



Lorsque vous percutez un corps

étranger ou si l’appareil s’y prend

dedans, éteignez le moteur

et vérifiez si des dégâts se sont

produits. Faites supprimer le

dommage avant de poursuivre

l’utilisation de l’appareil. N’utilisez

pas l’appareil si sa lame est

tordue, fissurée ou émoussée.

Jetez les lames tordues, voilées,

fissurées ou cassées.



N’aiguisez pas la lame de coupe.

Pendant l’utilisation, la lame

aiguisée peut se briser et provo-

quer des blessures graves.

Ceci peut provoquer des blessu-

res graves. Remplacez la lame

émoussée.

La pagina si sta caricando...

MTD H 15 Original Operating Instructions

MTD H 15 Original Operating Instructions

in altre lingue

Documenti correlati

Altri documenti