ProLights MINIECLFRFC Manuale utente

EN - IT

USER MANUAL

MANUALE UTENTE

FRESNEL PROIECTOR

MINIECLFRFC

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.02-07/19

1

MINIECLFRFC

Packing content

• MINIECLFRFC

• Barn doors

• Gel frame

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Technical drawing

1. 1 Operating elements and connections1. 1 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX mode3. 4 DMX mode

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Screen3. 6 Screen

3. 7 Advanced3. 7 Advanced

3. 8 Fixture information3. 8 Fixture information

3. 9 Master Slave3. 9 Master Slave

3. 10 Eects mode3. 10 Eects mode

3. 11 Static3. 11 Static

3. 12 Manual mode3. 12 Manual mode

3. 13 Connection of the DMX line3. 13 Connection of the DMX line

3. 14 Construction of the DMX termination3. 14 Construction of the DMX termination

3. 15 Channels DMX3. 15 Channels DMX

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement4. 2 Fuse replacement

4. 3 Trouble shooting4. 3 Trouble shooting

2

3

4

5

6

7

9

10

11

12

13

14

18

19

MINIECLFRFC

2

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with a temperature of over 40 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

3

MINIECLFRFC

- 1 - TECHNICAL DRAWING

Fig.1 - Technical drawing

Fig.2

1

6

7

9

8

5

2

3

4

5

8

9

MINIECLFRFC

4

1.1 OPERATING ELEMENTS AND CONNECTIONS

1. AIR OPENING

2. LOCKING KNOB for mounting bracket

3. MOUNTING BRACKET

4. BARN DOOR HOLDER for insertion and lock-

ing barn door

5. Rotary knob for manual focus

6. CONTROL PANEL with display, 4 button and

rotary knob used to access the control panel

functions and manage them

7. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only

8. Cable exible with 16A Shuko plug for con-

nection to a socket (100-240V~/50-60Hz)

9. Cable exible composed of a DMX IN (5-pole

XLR): 1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C,

5 N/C and DMX OUT (5-pole XLR): 1 = ground,

2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

Fig.3

5

MINIECLFRFC

- 2 - INSTALLATION

2.1 MOUNTING

MINIECLFRFC is designed for applications in exhibition areas, commercial spaces, museums, restaurant,

churches, and any other installation where size is an important factor. For xing, stable mounting clips are

required. The mounting place must be of sucient stability and be able to support a weight of 10 times

of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The

adjust the projector and use the knobs.

NOTE - To install the MINIECLFRFC projector, insert the clamp or a suitable clamp to x it to a suspended

system.

MINIECLFRFC

6

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn on the MINIECLFRFC connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then

the unit is ready for operation.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

CAUTION - Mains voltage must be switched o before mounting; maintenance.

3.2 BASIC

Access control panel functions using the four panel buttons land rotary knob located directly underneath

the LED Display (g.4).

MENU

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

Fig.4- Functions of the buttons

7

MINIECLFRFC

3.3 MENU STRUCTURE

MENU

1 CONNECT

ð

DMX Address

ð

Value (001-512)

DMX Mode

ð

Theater 1CH

ð

Amber Shift on Default: 2800K

Color Temperature (2800

~ 8000K)

Hue -025 ~ 025

Manual Color

Red 000 ~ 255,

Green 000 ~ 255

Blue 000 ~ 255

Lime 000 ~ 255

2CH

ð

Amber Shift on Default: 2800K

Color Temperature (2800

~ 8000K)

Hue -025 ~ 025

Manual Color

Red 000 ~ 255

Green 000 ~ 255

Blue 000 ~ 255

Lime 000 ~ 255

3CH

4CH 1

5CH

9CH 1

14CH

17Ch

Default: 9CH 1

ð

Tour 4Ch 2

6Ch

7Ch

9Ch 2

12Ch

2 SETUP

ð

Screen

ð

Back Light

Flip Display

Key Lock

ð

On

10S

20S

30S

No-Yes

Default: 10s

Default: No

3 ADVANCED

ð

Full On Mode

ð

HB

Studio

Defaul: Studio

Dimmer Mode

ð

O

Dimmer 1

Dimmer 2

Dimmer 3

Default: O

White Balance

ð

O Default: O

Adjust

ð

Red 125 ~ 255

Green 125 ~ 255

Blue 125 ~ 255

Lime 125 ~ 255

Led Frequency

ð

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Default: 1200Hz

Factory Reload

ð

No-Yes Default: No

MINIECLFRFC

8

4 INFORMATION

ð

Fixture Hours

Version

Temperature

UID

ð

0-9999

V1.0

**°C

15D00224****

5 STAND ALONE

ð

Master/Slave

ð

Master

Slave

Default: Slave

Eects

ð

Eect 1

Eect 2

Eect 3

Eect 4

Eect 5

ð

1 ~ 100 Default:

Eect1,Speed=100

Static

ð

Fixed Color

ð

R

G

B

L

RG

RB

RL

GB

GL

BL

RGB

RGL

RBL

GBL

RGBL

ð

Dimmer =

0 ~ 255

Default: RGBL

Color Tempera-

ture

2800K

3200K

4200K

5500K

6000K

8000K

ð

Dimmer =

0 ~ 255

Hue= -025

- 025

Default: 3200K

Dimmer: 255

ð

Manual Color

Mixer

ð

Red 000 ~ 255

Green 000 ~ 255

Blue 000 ~ 255

Lime 000 ~ 255

ð

000 ~ 255 Default: RGBL= 255

9

MINIECLFRFC

3.4 DMX MODE

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select Connect, then press the ENTER button to enter the

next menu.

• Press the UP / DOWN keys to select DMX Address, and press the button ENTER to conrm.

• Press UP/DOWN button to select the desired value (001 ~ 512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the MINIECLFRFC with a light controller, adjust the DMX start address for the rst a DMX

channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX chan-

nel, adjust the start address 33 on the MINIECLFRFC. The other functions of the light eect panel are then

automatically assigned to the following addresses. An example with the start address 33 is shown below:

Number

DMX channels

Address of

start (example)

DMX address

occupied

Next possible start address

for unit n ° 1

Next possible start address

for unit n ° 2

Next possible start

address for unit n ° 3

1 33 33 34 35 36

2 33 33-34 35 37 39

3 33 33-35 36 39 42

4 33 33-36 37 41 45

5 33 33 - 37 38 43 48

6 33 33-38 39 45 51

7 33 33 - 39 40 47 54

9 33 33 - 31 32 41 50

12 33 33 - 44 45 57 69

14 33 33 - 46 47 61 75

17 33 33 - 49 50 67 84

. . . . . . . . . . . .

DMX Address: 33 DMX Address: 48DMX Address: 38 DMX Address: 43

Fig.5 - Example 5 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

MINIECLFRFC

10

3.5 DMX CONFIGURATION

MINIECLFRFC is equipped with dierent DMX conguration.

• Press the button MENU so many times until shows DMX Mode, and press the button ENTER to conrm.

• Select the desired DMX mode and conguration (Theater: 1CH - 2CH - 3CH - 4CH 1 - 5CH - 9CH1 - 14CH - 17CH; Tour:

4CH 2 - 6CH - 7CH - 9CH 2 - 12CH) through the buttons UP/DOWN.

The tables on page 15, 16, 17 e 18 indicate the operating mode and DMX value.

3.6 SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select Set Up, then press the ENTER button to enter the

next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

On or choose another value to turn o the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select Yes to activate or No to dis-

able this function.

- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function

is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-

tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, UP,

DOWN, ENTER. Select Yes to activate or No to disable.

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.7 ADVANCED

You can change the parameters for the device by following these steps:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select the Advanced. Press the ENTER button to conrm.

• Press UP/DOWN button to select the desired option and press the ENTER button to conrm:

- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the

maximum value of the colors) or Studio mode with a automatic white balance.

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

- White Balance - To balance the white on each color. Select the color (Red, Green, Blue and Lime) and the

value (125 ~ 255) using the UP / DOWN button and press the ENTER button to conrm.

- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz ~ 25 KHz using the UP /

DOWN button and press ENTER to conrm the selection.

- Factory Reload - To reset the unit. Select Yes or No and select the UP / DOWN button to conrm.

Press the MENU button to go back or to meet the waiting time to exit the setup menu.

11

MINIECLFRFC

3.8 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Information, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Software Version - Through Temperature function you can display the temperature of the device.

- Temperature - Through Temperature function you can display the temperature of the device.

- UID - This option shows the RDM identication number.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.9 MASTER SLAVE

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Master/Slave and press ENTER to conrm

your choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Slave, if the unit is not connected to other units.

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.10 EFFECTS MODE

This xture has a built-in automatic program. To access this, please see the below instructions:

• To enter the Eects mode, press the ENTER button to access the menu.

• Press UP/DOWN button to select Stand Alone, then select Eect. Press ENTER to conrm

• Press UP/DOWN button to select the desired program Eect 1, Eect 2, Eect 3, Eect 4, Eect 5, then press

ENTER to conrm.

• Set the value (1 ~ 100), then press the ENTER button to conrm.

3.11 STATIC

The unit allows you to create congurations that can be set through the following procedure:

• To enter to Static mode, Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select Stand Alone, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Static and press ENTER to conrm your

choice.

• Through the UP/DOWN buttons select Fixed Color and press the ENTER button to conrm the desired

function.

• Set the colors (R, G, B, L, RG, RB, RL, GB, GL, BL, RGB, RGL, RBL, GBL, RGBL, 2800 K, 3200 K, 4200 K, 5500 K, 6000 K, 8000 K)

or value (000 ~ 255) through the UP/DOWN buttons, then press the ENTER button to conrm

• Press the MENU button repeatedly to exit the menu and to save the changes made.

NOTE: once the projector is connected to a power outlet, to directly access the Present Dimmer mode, simply

double click on the knob, rotating it. After that, choice the desired value.

MINIECLFRFC

12

3.12 MANUAL MODE

This mode allows to combine the colors (Red, Green,Blue and Lime).

• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button.

• Using UP/DOWN buttons Select Static, then press ENTER.

• Select Manual Color through the UP/DOWN buttons, then press the ENTER button.

• Select the color Red, Green,Blue and Lime through the UP/DOWN buttons, then press the ENTER button.

• Using UP/DOWN buttons, select the desired color value 000 ~ 255.

• Press the ENTER button to continue to the next color Red, Green,Blue and Lime.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

13

MINIECLFRFC

Fig.6

Fig.7

3.13 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.14 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

5 pin XLR connector

1 CHANNEL THEATER

MODE

FUNCTION DMX

Value

1 Ch

1

DIMMER

0~100% 000 - 255

5 CHANNELS THEATER

MODE

FUNCTION DMX

Value

5 Ch

1

DIMMER

0~100% 000 - 255

2

CTO

2800 K -3200K

3200 K-4200 K

4200 K-5500K

5500 K-6000K

6000 K-8000K

000 - 051

052 - 102

103 - 153

154 - 204

205 - 255

3

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

4

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

5

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

4 CHANNELS 1 THEATER

MODE

FUNCTION DMX

Value

4 Ch1

1

DIMMER

0~100% 000 - 255

2

CTO

2800 K - 3200 K

3200 K - 4200 K

4200 K - 5500 K

5500 K - 6000 K

6000 K - 8000 K

000 - 051

052- 102

103 - 153

154 - 204

205 - 255

3

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

4

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

2 CHANNELS THEATER

MODE

FUNCTION DMX

Value

2 Ch

1

DIMMER

0~100% 000 - 255

2

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

3 CHANNELS THEATER

MODE

FUNCTION DMX

Value

3 Ch

1

DIMMER

0~100% 000 - 255

2

CTO

2800 K - 3200 K

3200 K - 4200 K

4200 K - 5500 K

5500 K - 6000 K

6000 K - 8000 K

000 - 051

052 - 102

103 - 153

154 - 204

205 - 255

3

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

MINIECLFRFC

14

3.15 CHANNELS DMX

9 CHANNELS 1 THEATER

MODE

FUNCTION DMX

Value

9 Ch 1

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

LIME

0~100% 000 - 255

6

CTO

2800 K - 3200 K

3200 K- 4200 K

4200 K - 5500 K

5500 K - 6000 K

6000 K - 8000 K

No Function

000 - 042

043 - 084

085 - 126

127 - 168

169 - 210

211 - 255

7

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

8

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

9

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

14 CHANNELS THEATER

MODE

FUNCTION DMX

Value

14 Ch

1

DIMMER

0~100% 000 - 255

2

DIMMER FINE

0~100% 000 - 255

3

RED

0~100% 000 - 255

4

RED FINE

0~100% 000 - 255

5

GREEN

0~100% 000 - 255

6

GREEN FINE

0~100% 000 - 255

7

BLUE

0~100% 000 - 255

8

BLUE FINE

0~100% 000 - 255

9

LIME

0~100% 000 - 255

10

LIME FINE

0~100% 000 - 255

11

CTO

2800 K - 3200 K

3200 K- 4200 K

4200 K - 5500 K

5500 K - 6000 K

6000 K - 8000 K

No Function

000 - 042

043 - 084

085 - 126

127 - 168

169 - 210

211 - 255

12

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

13

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

14

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

15

MINIECLFRFC

6 CHANNELS TOUR

MODE

FUNCTION DMX

Value

6 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

LIME

0~100% 000 - 255

6

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

4 CHANNELS 2 TOUR

MODE

FUNCTION DMX

Value

4 Ch 2

1

RED

0~100% 000 - 255

2

GREEN

0~100% 000 - 255

3

BLUE

0~100% 000 - 255

4

LIME

0~100% 000 - 255

17 CHANNELS THEATER

MODE

FUNCTION DMX

Value

17 Ch

1

DIMMER

0~100% 000 - 255

2

DIMMER FINE

0~100% 000 - 255

3

STROBE

No Function (shutter open)

Strobe eect slow to fast

No Function (shutter open)

Random strobe eect slow to fast

No Function (shutter open)

000 - 030

031 - 100

101 - 130

131 - 200

201 - 255

4

CTO

2800 K - 3200 K

3200 K - 4200 K

4200 K - 5500 K

5500 K - 6000 K

6000 K - 8000 K

000 - 050

051 - 101

102 - 152

153 - 203

204 - 255

5

HUE

-25 to 0

No Function

0 to +25

000 - 126

127 - 127

128 - 255

6

CROSSFADE

0~100% 000 - 255

7

RED

0~100% 000 - 255

8

RED FINE

0~100% 000 - 255

9

GREEN

0~100% 000 - 255

10

GREEN FINE

0~100% 000 - 255

11

BLUE

0~100% 000 - 255

12

BLUE FINE

0~100% 000 - 255

13

LIME

0~100% 000 - 255

14

LIME FINE

0~100% 000 - 255

15

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

16

CTO ON COLORS

0~100% 000 - 255

17

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

MINIECLFRFC

16

7 CHANNELS TOUR

MODE

FUNCTION DMX

Value

7 Ch

1

DIMMER

0~100% 000 - 255

2

RED

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

BLUE

0~100% 000 - 255

5

LIME

0~100% 000 - 255

6

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

7

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

9 CHANNELS 2 TOUR

MODE

FUNCTION DMX

Value

9 Ch 2

1

RED

0~100% 000 - 255

2

RED FINE

0~100% 000 - 255

3

GREEN

0~100% 000 - 255

4

GREEN FINE

0~100% 000 - 255

5

BLUE

0~100% 000 - 255

6

BLUE FINE

0~100% 000 - 255

7

LIME

0~100% 000 - 255

8

LIME FINE

0~100% 000 - 255

9

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

12 CHANNELS TOUR

MODE

FUNCTION DMX

Value

12 Ch

1

DIMMER

0~100% 000 - 255

2

DIMMER FINE

0~100% 000 - 255

3

RED

0~100% 000 - 255

4

RED FINE

0~100% 000 - 255

5

GREEN

0~100% 000 - 255

6

GREEN FINE

0~100% 000 - 255

7

BLUE

0~100% 000 - 255

8

BLUE FINE

0~100% 000 - 255

9

LIME

0~100% 000 - 255

10

LIME FINE

0~100% 000 - 255

11

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

12

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

17

MINIECLFRFC

18

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Using a screwdriver, unscrew the fuse holder cap from the housing.

3. Remove the blown fuse and replace with a good fuse of the same type and rating.

4. Screw the fuse holder cap back in place and reconnect power

Fig.8

La pagina sta caricando ...

ProLights MINIECLFRFC Manuale utente

ProLights MINIECLFRFC Manuale utente

in altre lingue

Documenti correlati

Altri documenti