D.T.S. Illuminazione s.r.l.

Via Fagnano Selve 10/12/14

47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it http://www.dts-lighting.it

Le informazioni contenute in questo documento sono state attentamente redatte e

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

6 - IMPORTANT SAFETY INFORMATION ................................................................... 9

6.1 Fire prevention...................................................................................................... 9

6.2 Prevention of electric shock .................................................................................. 9

6.3 Protection against ultraviolet radiation .................................................................. 9

6.4 Safety ................................................................................................................... 9

6.5 Level of protection against the penetration of solid and liquid objects .................. 9

9.2 Protection against liquids .................................................................................... 16

9.3 Movement ........................................................................................................... 17

9.4 Risk of fire .......................................................................................................... 17

9.5 Forced ventilation ............................................................................................... 17

9.6 Ambient temperature .......................................................................................... 17

10 - MAINS CONNECTION ......................................................................................... 18

10.1 Protection ......................................................................................................... 18

11 - DMX SIGNAL CONNECTION .............................................................................. 19

11.1 DMX addresses ................................................................................................ 20

11.2 Selecting the DMX address .............................................................................. 20

20 - PERIODIC CONTROLS ....................................................................................... 32

Graphic symbols used on this manual:

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The unit is not for residential use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or

4- TECHNICAL FEATURES

over very long distances. A wide variety of gobos for unique mid-air effects is

available. In “Spot” mode, EVO offers striking brightness (over 45.000 Lux at 25

meters) and an extra-wide linear zoom (3,5° - 39°).

Thanks to its improved optics, EVO delivers razor-sharp gobo projections over the

whole zoom range. EVO features also include:

Cutting edge Color Synthesis featuring Linear CMT, Linear CTO, a 21-color palette

going from soft nuances to rich saturated colors, and analogue two-tone generation.

The exclusive circular 8-facet or linear Dyna-Prism system (D.T.S. patent pending),

capable of enhancing any gobo with spectacular animations and dynamic

kaleidoscopic effects never seen before.

television studios to theatres. The ultra-luminous multi-function EVO is perfect for

rental companies, who need compact feature-packed units that are easy to handle,

install and store.

EVO FPR

• Electronic ballast 90-260Vac 50-60 Hz • FPR (Free Pan Rotation) • Black finish

1.530.000 Lux at 5 m (Beam mode)

1.125.000 Lux at 5 m (Spot mode)

16-bit motorized wide-excursion linear zoom

Beam opening:

2° - 36° (Beam projection)

3.5° - 39° (Spot projection)

16-bit motorized linear focus

Linear dimmer / shutter / strobe (0,85 flash/sec to 10 flash/sec)

Effect glass filters

Frost filter

Linear CMY

Linear CTO

21-colour wheel

Two-tone generation

Dyna-Prism (D.T.S. Patent Pending)

Li-Fe backup battery for controlling the main parameters even when EVO is not

powered

LCD graphic display + 4 soft-keys (control / management / monitoring of the main

parameters)

RDM

Art-Net ready

‘FPR’ system (D.T.S. patent)

Pan: limitless rotation, in both directions;

360° rotation in 1.56 sec.; Tilt 270°: 1,5 sec.

Tri-phase stepper motor technology for ultra-fast silent movements

16-bit resolution

Selectable speed ranges

Pan / Tilt lock

Power supply

Power supply: POWERCON panel connectors (In/Out)

Operating ambient temperature

-10° / 40°

Internal safety devices

Overvoltage circuit protection and overtemperature circuit protection

International certifications

Safety: EN 60598-1: 1993

EN 60598-2-17: 1989

A1-A3: 1993

EMC: EN 55015

* 1 x XLR 5 Pins male cable connector (Code 0508B066)

* 1 x XLR 5 Pins female cable connector (Code 0508B065)

* 2 x Omega clamp with “Fast Lock” connection 1/4 turn (Code 02K00549)

• “C” Clamp G100 black / professional (max. load 200Kg) (Code 0521A015)

• Aliscaf Clamp (max. capacity load 100Kg) (Code 0521A008)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (Code

0521A010)

6- IMPORTANT SAFETY INFORMATION

- EVO uses a SIRIUS HRI 440W lamp.

The use of any other alternative lamp is not recommended and will null and void the

-High voltage is present inside the unit.

Unplug the unit prior to performing any function which involves touching the inside of

working order.

-Never look directly the lamp when it is on.

-The projector should always be installed with bolts, clamps and other tools that are

The ambient temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 20 minutes prior to attempting to

replace the lamp.

-Always wear suitable hand protection when handling the lamp.

-The projector is classified as an ordinary appliance and its protection level against the

penetration of solid and liquid objects is IP20.

We recommend the use of a safety cable or chain connected to the EVO and to the

suspension truss in order to avoid the fixture accidentally falling should the main fixing

point fail.

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

Pan: limitless rotation, in both directions; 360° rotation in 1.56 sec.; Tilt 270°: 1,5 sec.

Each fixture produces heat and must be installed in a well-ventilated place.

It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

You will note, on inspection, that the unit features various air inlets and cooling fans

located on both the base and head of the fixture.

These should, under no circumstances, be blocked or obstructed whilst the projector

is in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

EVO with electronic ballast operates at 90-260Vac 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 3,5 amps

at 230Vac, or 7,5 amps at 90Vac each unit connected.

Max 4 EVO Units @ 230Vac

Max 2 EVO Units @ 120Vac

FUSE

The use of a thermal magnetic circuit breaker is recommended for each EVO.

A good earth connection is essential for the correct operation of the projector.

The unit operates using the digital DMX 512 signal.

Connection between the mixer and the projector or between projectors must be carried

out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

For Installations where long distance DMX cable connections are needed, we suggest

to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

EVO can be used in 2 different DMX modes: 32 DMX control channels (Default) or 24

DMX control channels.

Here below is described the DMX channels addressing for the controller when EVO is

set to 32 and 24 DMX control channels:

32 channels mode (Default)

projector 6 A121

This procedure require a base knowledge of computer applications and Windows

Hyperterminal program. Please refer to an authorised D.T.S. service centre.

To update the software version of EVO you need:

- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)

- USB-DMX Driver for the D.T.S. RED BOX interface

- “D.T.S. Firmware upgrade utility” program installed on the PC

- Latest software release available for EVO unit

4. Send the new software version into the unit by using “D.T.S. Firmware upgrade

utility” program.