Kathrein Satellite TV System UFD 515 Manuale utente

Categoria
Set-top box TV
Tipo
Manuale utente

Questo manuale è adatto anche per

Operating Manual
Order no.: 260 473
Preface
Preface
Dear Customer,
The following operating manual will help you obtain the best optimal use from the
extensive features of your new satellite receiver.
We have written this operating manual as comprehensibly as possible and as con-
cise as necessary. A brief lexicon containing specialised terms not easily translat-
able has been appended at the end of this manual. To further assist you in your
search for a specific term, we have also added an index.
We have taken the environment into account with the mains switch. Therefore,
during longer pauses separate your receiver from the mains, in order to save en-
ergy. During short pauses, you should switch the receiver to standby with the re-
mote control, so the least amount of energy is used.
We wish you a great reception and much enjoyment with your new satellite re-
ceiver.
Your,
KATHREIN-Team
If you have any unexpected problems with your receiver, please contact your spe-
cialist supplier through our hotline.
Tel: (08031) 18 47 00
Fax: (08031) 18 46 76
Important Notes:
With regard to the programme allocation of the satellites and transponders,
changes always occur. In such cases, it is necessary to carry out new pro-
gramme settings, although factory pre-programming is always in accordance with
the respective, newest developments.
You can gather the details for the new setting from teletext on SAT 1, the internet,
or respective magazines. Refer to the section "Changing frequency" for more in-
formation.
Your receiver has been equipped with the newest respective Software at the fac-
tory. We are always trying to adjust the Software to the desires of our customers
and the state-of-the-art technology. Refer to section "Software and programme
lists update," for more information.
3
Contents
Contents
Preface ...............................................................................................................................................................3
Contents ............................................................................................................................................................4
Safety instructions ...........................................................................................................................................7
Important notes regarding operation ..............................................................................................7
Extended absence / thunderstorms............................................................................................................ 7
Mains lead .................................................................................................................................................. 7
Cleaning ..................................................................................................................................................... 7
Children-at-play .......................................................................................................................................... 7
Repairs ....................................................................................................................................................... 7
Connections................................................................................................................................................ 7
Place of installation..................................................................................................................................... 8
Ventilation................................................................................................................................................... 8
Humidity, exposure to sunlight, heat .......................................................................................................... 8
Mains voltage ............................................................................................................................................. 8
Grounding................................................................................................................................................... 8
Control, displays and connection...................................................................................................................9
View of front panel ..............................................................................................................................................9
View of rear panel ..............................................................................................................................................9
Front panel controls and displays.......................................................................................................................9
Rear panel controls and displays .......................................................................................................................9
Remote control handset keys ...........................................................................................................................10
Command of the remote control ...................................................................................................................11
Operating instructions ...................................................................................................................................12
Menu concept ...................................................................................................................................................12
Button functions ................................................................................................................................................12
Alphanumeric entries ........................................................................................................................................12
Alphanumeric assignments of number buttons on the remote control .............................................................13
Language selection - OSD ...............................................................................................................................13
Connection and start-up ................................................................................................................................14
To connect receiver ..........................................................................................................................................14
Sat IF connection...................................................................................................................................... 14
Preconditions for receiving digital signals ................................................................................................ 14
Presetting receiving system ..................................................................................................................... 14
LNB-supply voltage .................................................................................................................................. 15
TV and video recorder connection ........................................................................................................... 15
Audio connection ...................................................................................................................................... 15
Inserting batteries in the remote control................................................................................................... 15
First time installation......................................................................................................................................16
The first steps ...................................................................................................................................................16
Factory setting of receiver ................................................................................................................................16
On screen displays.........................................................................................................................................17
Important screen displays.................................................................................................................................17
TV channel identifier................................................................................................................................. 17
Teletext ................................................................................................................................................. 17
Radio channel indicator............................................................................................................................ 17
Error message .......................................................................................................................................... 17
TV programme list .................................................................................................................................... 17
Radio programme list ............................................................................................................................... 18
Programme selection .....................................................................................................................................19
Selecting a TV programme...............................................................................................................................19
Reception status....................................................................................................................................... 19
TV programme selection by number entry .......................................................................................................20
Switching over to radio programme..................................................................................................................20
4
Contents
Reception status - radio ........................................................................................................................... 20
Selecting a radio programme by number entry ........................................................................................ 21
Common Interface ..........................................................................................................................................22
Timer settings .................................................................................................................................................23
VPS signal ........................................................................................................................................................23
Programme overview .....................................................................................................................................24
EPG ..................................................................................................................................................................24
Full EPG............................................................................................................................................................24
EPG timer programming........................................................................................................................... 24
Sound settings................................................................................................................................................25
Setting the volume............................................................................................................................................25
Stereo and two-channel sound reproduction....................................................................................................25
AC3 ...................................................................................................................................................................25
Mute.......................................................................................................................................................... 25
Programme list................................................................................................................................................26
Selecting programmes last received ................................................................................................................26
Favourite Programmes .....................................................................................................................................26
Programme assortment ....................................................................................................................................27
To delete a programme ....................................................................................................................................27
To add a programme manually.........................................................................................................................28
Adding/removing satellites............................................................................................................................30
Setting up a satellite .........................................................................................................................................30
To enter a satellite name ..................................................................................................................................30
Remove satellite ...............................................................................................................................................31
Password.........................................................................................................................................................32
Factory setting .......................................................................................................................................... 32
Entering a password................................................................................................................................. 32
Parental lock............................................................................................................................................. 33
Operation from the front panel......................................................................................................................34
Backup operation..............................................................................................................................................34
Setting system parameters............................................................................................................................35
System parameters...........................................................................................................................................35
Parental lock............................................................................................................................................. 35
System information................................................................................................................................... 35
Local time / timer ...................................................................................................................................... 35
Timer menu .............................................................................................................................................. 36
Summer time ............................................................................................................................................ 36
TV type ..................................................................................................................................................... 36
Picture format ........................................................................................................................................... 36
Screen ...................................................................................................................................................... 36
A/V mode .................................................................................................................................................. 36
OSD colour ............................................................................................................................................... 37
OSD trans................................................................................................................................................. 37
Installation menu ............................................................................................................................................38
LNB configuration ..................................................................................................................................... 38
Oscillator frequency L.O. ...................................................................................................................... 38
Changing the oscillator frequency ........................................................................................................ 39
Operation .............................................................................................................................................. 39
Standby................................................................................................................................................. 39
Receiving two satellites ........................................................................................................................ 39
DiSEqC setting...................................................................................................................................... 40
Antenna settings....................................................................................................................................... 40
Satellite search ......................................................................................................................................... 40
TP set-up/search ...................................................................................................................................... 41
5
Contents
Transponder selection .......................................................................................................................... 41
DiSEqC (UFO) Set-up .............................................................................................................................. 42
22-kHz signal ........................................................................................................................................ 42
Tone burst and DiSEqC signal ............................................................................................................. 42
Tone Burst ............................................................................................................................................ 43
DiSEqC ................................................................................................................................................. 43
DiSEqC Repeat..................................................................................................................................... 43
UFO mini............................................................................................................................................... 43
Remote frequency................................................................................................................................. 43
UFO micro............................................................................................................................................. 43
Factory setting .......................................................................................................................................... 44
Video recorder connection ............................................................................................................................45
Recording .........................................................................................................................................................45
Playback ...........................................................................................................................................................45
Software and programme lists update .........................................................................................................46
Data transfer from receiver to receiver ........................................................................................................47
Preparation .......................................................................................................................................................47
Transferring programme lists ................................................................................................................... 47
Transferring operating software ............................................................................................................... 47
Technical annex..............................................................................................................................................48
Technical features ............................................................................................................................................48
Technical data ..................................................................................................................................................49
Accessories ......................................................................................................................................................50
Scart socket assignments.................................................................................................................................50
Switchover VHS/S-VHS ........................................................................................................................... 50
Connection examples .......................................................................................................................................51
Connection arrangement 1: ...................................................................................................................... 51
Connection arrangement 2: ...................................................................................................................... 52
Glossary, abbreviations .................................................................................................................................53
Short technical lexicon ..................................................................................................................................54
Service .............................................................................................................................................................56
6
Safety instructions
Safety instructions
Important notes regarding operation
The following section contains important information relating to the operation, place
of installation and connecting-up of the receiver.
Read these notes carefully before putting the unit into operation.
Extended absence / thunderstorms
Always switch the unit off via its mains switch (at front left on unit) during periods of
extended absence or at the onset of thunderstorms. This also applies to any other
equipment that is connected to the receiver.
However, take into account any possible timer programming and switch the unit on
again in good time prior to the recording time.
Mains lead
Make certain that the mains lead (power supply lead) is undamaged. Never put the
unit into operation if the mains lead is damaged.
Cleaning
Withdraw the mains plug before cleaning the unit. Use a dry cloth for cleaning.
Clean the surface only and nothing else.
On no account open the housing. There is a risk of electric shock if components
within the unit are touched.
Children-at-play
Pay attention that children do not insert objects into the ventilation slots. There is a
risk of mortal danger due to electric shock.
Repairs
If your receiver needs repairing or changes to settings, get qualified specialists to
carry this out. Unauthorised opening and attempts at repairs entail loss of guaran-
tee.
The unit’s electrical safety can be affected by improper tampering with it.
The manufacturer’s liability excludes accidents occurring to the user when the unit
is opened.
Connections
The unit may be rendered inoperative or not work properly if the connections are
not wired up properly.
7
Safety instructions
Important notes for siting and installation.
Place of installation
Every electronic device generates heat. The rise in temperature, however, lies
within a safe range. Slight colour changes may occur to sensitive furniture surfaces
and veneers over the course of time due to the constant effect of heat. In conjunc-
tion with treated furniture surfaces, the unit’s rubber feet can likewise give rise to
changes in colour. Where necessary, place the unit on a suitable pad.
Ventilation
The heat that is generated in this unit is dissipated quite adequately. Never install
the receiver in a cabinet, shelf or rack with inadequate ventilation. Never close off
the cooling slots on the unit.
Do not place objects on top of the unit. Maintain a clearance of at least 10 cm
above the unit so that the heat generated within the unit is conducted away without
obstruction.
Humidity, exposure to sunlight, heat
Protect the unit against humidity, drips and splashing.
Do not place the unit close to radiators nor expose it to direct sunlight.
Mains voltage
Operate the receiver only from a 230V / 50 Hz mains voltage.
The unit must not be connected to the mains and switched on until after the con-
nections have been set up for the antenna and TV set.
Grounding
The parabolic antenna is to be grounded in accordance with regulations. The rele-
vant local and/or German VDE regulations are to be complied with here.
8
Control, displays and connection
Control, displays and connection
This section contains a brief description of all the control elements, displays and
connections. The key symbols presented here are also used when describing op-
erating sequences.
View of front panel
(Flap folded down)
View of rear panel
IF INPUT DIGITAL
920-2150MHz
14/18V max. 400mA
22kHz
VCR
AUX
UFD 515 260473
TV
IF OUTPUT
DiSEqC 1.1
DATA I/O
AC 88V-264V~
50/60 Hz
max.30W
Elektroschock-Gefahr!
Nicht öffnen
L
R
AUDIO VIDEO
DIGITAL
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9
Front panel controls and displays
Rear panel controls and displays
1 On/Off switch (with mains separation)
2 Menu button to call up or exit from menus
or submenus
3 Indicator to confirm remote control signal
4 Select-button
to confirm a selection
5 Power indicator
6 Standby indicator
7 Cursor keys to step through menus and
programmes, and for adjustment of the vol-
ume (corresponds to the remote control)
8 LED display (4-charachter 7-segment dis-
play) for display of programme position and
time
9 Common Interface for Pay-TV cards
10 Pressure catch for front flap
Open by lightly applying pressure on the
upper right-hand side
1 Audio output
2 Cinch sockets, left and right channel
2 Dolby Digital-output (AC3)
3 Video output (FBAS)
4 Scart socket TV connection
5 Scart socket VCR/AUX connection
6 DATA socket
Interface for serial data transmission
(Service)
7 Satellite IF signal input
Output of the LNB supply voltage and con-
trol signals (22-kHz and DiSEqC 1.1)
8 Satellite IF signal output
Output for a analogue secondary receiver.
The Sat IF signal is looped through.
9 Mains voltage supply line
9
Control, displays and connection
Remote control handset keys
A / B
M
F L
O K
T V
M
Calls up main menu
e
Power On -
Standby
A
Switch over of the
remote control
F
Calls up favourite
cate
g
ories
L
Last programme and
exit
T
Setting scart
connection
Radio Off
-
+
Volume /
Menu entries
O
Confirmation of the
submenus and main
entries
R
Radio On/Off
z
Programm-
informationen
i
Calls up
programme list
o
u
Programme selection
/ Selection of
submenus and menu
entries
l
Mute (On/Off)
1...2
Numerical input for
programmes, parental
lock, LO frequency
etc.
s
Sound selection
menu / Mono
language selection
10
Command of the remote control
Command of the remote control
The remote control features 2 command sets, making it possible to operate
2 receivers independently of each other in one room (not together with a twin
receiver).
Note For this purpose, program one receiver on the command set 1 and the second
receiver on the command set 2.
· Switch on receiver 1 and receiver 2 off with the power switch
Þ Press and hold the
Abutton.
Þ Enter "901" with the number buttons.
· To adopt the code, press the
ebutton to switch receiver 1 to standby and
then switch off the device with the power switch.
· Switch on receiver 2.
Þ Press and hold the
Abutton.
Þ Enter "902" with the number buttons.
· To adopt the code, press the ebutton to switch receiver 2 to standby and
then back into operation. Now switch on receiver 1 again.
Þ Press and hold the
Abutton.
Þ Enter "903" with the number buttons.
Note When carrying out the first two settings, the remote control must be directed at the
respective receiver (when switched on).
By pressing the
Abutton, you can now switch between the two command sets A
and B (toggle function) and alternately operate both receivers.
Command set 1 is always active as the on-delivery setting.
Note If you are operating only one receiver and the active command set is switched over
by mistake so that this receiver can no longer be operated, the remote control can
be easily switched back to command set 1. For this purpose, follow the procedure
described above.
11
Operating instructions
Operating instructions
Menu concept
The menu concept is based on a logical operation sequence.
Note: Coloured backgrounds are used to emphasise the selected menus, submenus and
menu items as well as the parameters to
be set. The menus are to a large extent
self-explanatory. You will find information
relating to the selected menu point in the
information box displayed under the menu.
Press the
M to select the main menu
and press the
ou buttons to
select the submenus.
Press
O to access the submenus. The
items in the submenus are selected
by pressing the
ou buttons.
The settings allocated to specific menu items are executed either by pressing the
-+ buttons or the number buttons.
Press
L or M to exit the main menu, submenus and menu items.
Button functions
i is a changeover button (main channel list or favourite list) with menu function.
Press
L to exit the setting.
T
is a changeover button. Identifier self-deleting.
s
is a switch-on button with menu functions. Press the button again to exit
z is a switch-on button with menu functions. Press the button again to exit.
F is a switch-on button with menu functions. Press the button again to exit.
R is a function selection button. Press once again to change function.
l is a function selection button. Press once again to change function.
Alphanumeric entries
Use the number buttons to enter the programme and satellite names. They pro-
duce numbers and letters in the name fields of the corresponding menus. Position
the bar cursor on the name field. The first position automatically assumes a dark
background. You can now also enter letters with the number buttons by pressing
the corresponding button several times. For example, Q, Z and — are additionally
allocated to the "1" button (see table on next page).
12
Operating instructions
Alphanumeric assignments of number buttons on the remote control
Button 1 X 2 X 3 X 4 X
1
1
Q
Z
-
2
2
A
B
C
3
3
D
E
F
4
4
G
H
I
5
5
J
K
L
6
6
M
N
O
7
7
P
R
S
8
8
T
U
V
9
9
W
X
Y
0
0
SPACE
Language selection - OSD
To select the language for the on-screen menus press:
M C ou C menu language C -+ C English C M
The available languages are German, English, French, Italian, Spanish,
Portuguese, Dutch, Greek and Turkish.
13
Connection and start-up
Connection and start-up
The following section is specifically intended for the specialist dealer. You only
need to read this section if you are carrying out the installation yourself.
You will find sample configurations in the section "Connection examples".
First, carry out all installation work before connecting the receiver to the mains
power supply.
Refer to the information provided in the section "Safety instructions“.
To connect receiver
Sat IF connection
Connect the Sat-IF input of the receiver to the satellite receiving system (satellite
dish).
Use a coaxial cable with a standard F connector for this purpose.
If you need to fit the F-connector onto the cable,
strip the cable insulation as shown in the diagram (you will need to fold back
the braid) and
·
· slide the F-connector onto the cable, then turn it clockwise until it locks.
When fitting the connector make sure that no wires of the shield braid make con-
tact with the inner conductor. This could otherwise cause a short-circuit.
The quality of the reception signal depends on a good connection!
Preconditions for receiving digital signals
Make sure that your satellite antenna system is equipped with at least one univer-
sal LNB to facilitate digital reception in the high band range.
Presetting receiving system
The control signals for conventional receiving systems (satellite dishes) are preset,
i.e. 14/18 V for polarisation changeover and 22 kHz switching signal for LOW/HIGH
band changeover on multifeed reception systems.
The presetting will need to be changed in the installation menu, menu point "DiS-
EqC" if UFO or tone burst switching matrices are used in the receiving system.
Refer to the section "Installation menu, DiSEqC menu“ for this purpose.
It is important that you observe the application information provided for the matrix
used.
14
Connection and start-up
LNB-supply voltage
If the feed system (LNB) is powered by an external supply voltage and the LNB
supply voltage is not used for switching over polarity (e.g. Kathrein feed system
UAS 330), the LNB supply of the receiver must be set to "OFF" (see section "In-
stallation menu, LNB configuration“).
TV and video recorder connection
Use a SCART cable to connect the satellite receiver (TV SCART) and TV set. ·
·
·
·
If your TV set is equipped for stereo output, you can receive the sound in stereo via
the SCART connection.
Also use a SCART cable to connect the satellite receiver (VCR/AUX SCART)
and the video recorder.
Audio connection
If you wish to reproduce the sound via a hi-fi system, connect a corresponding
Cinch cable from the audio Cinch sockets on the receiver to the input sockets on
your hifi system.
The digital output is designed to facilitate connection to a Dolby Digital System.
Inserting batteries in the remote control
Remove the cover on the battery compartment on the underside of the remote con-
trol.
Insert the two supplied batteries in the remote control. Ensure correct polarity
of the batteries, the + and – markings are indicated inside the battery com-
partment.
Slide the cover back into the casing and lock in position.
Used batteries are special waste! Therefore, do not throw batteries into the house-
hold waste but rather deposit them at a collection depot for old batteries!
15
First time installation
First time installation
The first steps
Connect the receiver to the mains power supply.
Switch on the receiver by pressing the power button at the front of the unit.
You will see "- - - -“ in the LED display, afterwards "0000."
The operation indicator LED lights up red, the receiver is now in standby mode.
Switch on your TV set.
Switch on the receiver by pressing the
ebutton on the remote control.
The yellow LED at the front end of the receiver flashes every time a button on the
remote control is pressed.
You will see the factory preset programme on your TV screen. An information bar
indicating the programme provider, the time, the timer settings, the programme
status and the programme title will be displayed in the bottom section of the screen
provided the corresponding data are transmitted. The number of the programme
memory appears in the LED display.
The red standby indicator extinguishes.
You can now receive the TV and radio programme preset at the factory and select
them by pressing the
ou buttons. Press the Rand oubuttons to
select radio programmes. Press the
Ror Tbutton to return to TV programmes.
Refer to the section " Programme lists – TV/radio" for information on how to set up
and save other TV and radio programmes.
The reception status last set always reappears when the receiver is switched on.
If the message "bad or no signal" appears on the screen in addition to an on-
screen display indicating the programme last received, you will need to check the
system installation and/or the receiver settings. If this problem only applies to indi-
vidual programme slots, the problem may be due to an interruption in the transmis-
sion signal or a fault in the receiving system (cable or satellite system).
In this case, first check the connection configuration and then check whether the
basic settings of you receiver are correct for your system. In the case of doubt,
have a specialist do this for you.
Factory setting of receiver
Your receiver is pre-programmed to receive the ASTRA and HotBird satellites. You
will normally need to make no further settings. To receive both satellite systems or
other satellites you will require a multifeed arrangement with at least two LNBs in
front of the satellite dish if you are not connected to a communal or party system.
Please ask your provider.
Before you change the basic settings of your receiver, note down the settings in
the form provided at the end of this User's Guide. In doing so, you will be able to
restore the original settings at any time.
16
On screen displays
On screen displays
Important screen displays
The receiver functions are controlled by a microprocessor and extensive software.
The following explanations are intended to improve understanding of all proce-
dures and to minimise the risk of mistakes.
TV channel identifier
The channel identifier is displayed for several seconds every time the channel is
changed or by pressing the
Obutton.
The
I indicates that a channel is received
even if no picture can be seen (e.g. radio).
The film symbol indicates a TV channel
with the selected programme shown next
to it and whether teletext is received. The current time, start time and end time of
the current programme are shown on the next line provided these data are trans-
mitted. The + in the third line stands for the programme selection from the main
programme list. If the favourite list is selected, you will see the "apple" symbol at
this point. This is followed by the set sound reproduction mode (depending on the
direction of the symbolised sound waves, mono left, mono right or stereo can be
set, the digit indicates the number of sound channels). The programme title is
shown in the box on the right.
Teletext
Transmitted teletext is processed from the receiver - also for encrypted signals - for
the television set.
Radio channel indicator
The identifier for the set radio channel has
the same configuration. A music note
appears in the upper right-hand corner
indicating a radio channel. Programme
times and text are displayed only if the
corresponding data are transmitted with
the signal.
Error message
"Bad or no signal" indicates that there is a
fault in the reception system or in the re-
ceiver settings or the transponder is not
transmitting. Instead of the
I the channel
identifier shows a satellite antenna to-
gether with the message "bad or no
signal". Check the SAT-IF connection and
the LNB configuration. As an aid, refer to
the list of service settings provided at the end of this User's Guide.
TV programme list
Press the ibutton to show the pro-
gramme list. A + for the main programme
list or the "apple" symbol is indicated at
the top left. The list can be changed by
pressing the button again. Information
relating to the received satellites, the
polarisation, the symbol rate, scrambling,
17
On screen displays
favourite or standard programme and the parental control is provided in the column
below the symbol. The column on the left contains information relating to the chan-
nel, the programme provider and whether the programme is normally scrambled.
The required programme can be selected with the bar cursor and confirmed by
pressing the
Obutton.
Radio programme list
See above. The same applies to the radio programme list.
18
Programme selection
Programme selection
This section describes how you select analogue and digital TV programme with
your receiver and how you can set the required volume. This description of the
functions assumes that the receiver has been connected correctly.
If you wish to connect the receiver yourself, please read the section "Connection
and start-up" beforehand.
Selecting a TV programme
Reception status
The following information describes how to select other channels and shows what
the on-screen displays look like.
After switching on the receiver, simply
press the
oubuttons in order to se-
lect other TV programmes in their
ascending or descending order in the
channel memory.
Every time you press the button, an on-
screen display shows you the selected programme together with the time, the pro-
gramme start and end times as well as the programme title in the information box
provided these data are transmitted together with the signal.
By pressing the
Obutton, you can leave
this information box permanently dis-
played or switch it off by pressing the
button once again.
You will receive the "channel scrambled"
message for scrambled channels.
Here, you need an authorised card -PCMCIA- or Smart card of the respective Pay-
TV provider (refer to CA module).
A further option of selecting a different
programme is to press the
ibutton. The
TV programme list is now displayed. In the
left column, it will provide information
relating to the received satellites, the
transponder and its transmission fre-
quency, the polarisation, the symbol rate
and the scrambling. The programme
number, the programme broadcaster and
the type of reception signal (free to-
air/scrambled) is shown on the right.
With the
oubuttons you jump to the next programme, with the
-+ buttons you jump to the neighbouring page or with the buttons on the remote
control enter the programme number (Ch). Confirm your selection by pressing the
Obutton. Press the Lbutton to exit the programme list and remain in the al-
ready set programme.
19
Programme selection
TV programme selection by number entry
You can select a different TV programme during a current TV programme by enter-
ing the programme location number.
Use the number buttons
1to 0for the purpose of entering the programme lo-
cations.
Example You wish to select the TV programme "DSF". This programme is stored under the
programme location number 015. (The order of TV programmes is defined in the
programme memory and therefore only serves as an example here.)
To select this programme, press the numbers
1and 5one after the other. The
receiver waits for about 3 seconds for entry of the next number.
Follow the same procedure for all other programmes – i.e. also programmes with
three-digit programme location numbers. You do not have to enter leading zeros.
Switching over to radio programme
You can switch over from a TV programme to a radio programme.
Press the
Rbutton on the remote control for this purpose.
The receiver switches over to the programme location of the radio programmes last
set. You can return to the TV programme by pressing the same button or
T. The
corresponding display relating to the received programme, i.e. as when selecting
the TV programmes, appears on the screen. The LCD display shows a small "r"
together with the programme location number.
The screen will be blanked out after several seconds.
Reception status - radio
After the switch-over of the receiver, simply press the oubuttons to select
other radio channels in their ascending or descending order in the channel mem-
ory.
Every time you press the button, an on-
screen display shows you the selected
programme together with the time, the
programme start and end times as well as
the programme title in the information box
provided these data are transmitted
together with the signal.
By pressing the
Obutton, you can leave this information box permanently dis-
played or switch it off by pressing the button once again.
A further option of selecting a different
programme is to press the
ibutton. The
radio programme list is now displayed. In
the left column, it will provide information
relating to the received satellites, the
transponder and its transmission fre-
quency, the polarisation, the symbol rate
and the scrambling. The programme
number, the programme broadcaster and
the type of reception signal (free to-
air/scrambled) is shown on the right.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57

Kathrein Satellite TV System UFD 515 Manuale utente

Categoria
Set-top box TV
Tipo
Manuale utente
Questo manuale è adatto anche per