Tyan S2882 Manuale utente

1

http://www.TYAN.com

Thunder K8S Pro

///

S2882

Revision 1.02

manual may be reproduced or translated without prior written consent from TYAN

Computer Corp.

All registered and unregistered trademarks and company names contained in this manual

are property of their respective owners including, but not limited to the following.

TYAN, Thunder K8S Pro are trademarks of TYAN Computer Corporation.

AMD, Opteron, and combinations thereof are trademarks of AMD Corporation.

AMI, AMIBIOS8 are trademarks of American Megatrends Inc.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE,is a trademark of SuSE AG.

Linux is a trademark of Linus Torvalds

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Broadcom

®

is a trademark of Broadcom Corporation and/or its subsidiaries

ATI and Rage XL are trademarks of ATI Corporation

Silicon Image is a trademark of Silicon Image, Inc.

Information contained in this document is furnished by TYAN Computer Corporation and

has been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability

whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for a particular purpose

or merchantability. TYAN retains the right to make changes to product descriptions and/or

specifications at any time, without notice. In no event will TYAN be held liable for any

direct or indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this document.

http://www.TYAN.com

2

Table of Contents

Before you begin… Page 4

Chapter 1: Introduction

Congratulations Page 5

Hardware Specifications Page 5

Software Specifications Page 6

Chapter 2: Board Installation

2.00 Board Image Page 8

2.01 Block Diagram Page 9

2.02 Board Parts, Jumpers and Connectors Page 10

2.03 Gigabit LAN_1 Front Panel LED Header (J1) and Gigabit LAN_2

Front Panel LED Header (J2)

Page 12

2.04 Front Panel Connector (J6) Page 12

2.05 Clear CMOS Jumper (J8) Page 13

2.06 SMBus_0 Connector (J11) Page 13

2.07 USB Connector Headers (J12) Page 14

2.08 10/100 LAN front Panel LED Header (J17) Page 14

2.09 Chassis Intrusion Connector (J19) Page 15

2.10 ZCR Connector (J22) Page 15

2.11 COM2 Header (J23) Page 16

2.12 PCI-X Bridge B (PCI 1 & PCI 2) PCI-X Speed Select Jumper (J24 /

J39)

Page 16

2.13 PCI-X Bridge A (PCI 3 & PCI 4) force PCI Mode Jumper (J41) Page 17

2.14 Keylock Enable/Disable Jumper (J42) Page 17

2.15 PCI-X Bridge A (PCI 3 & PCI 4 & SCSI7902 & BCM5704) PCI-X

Speed Select Jumper (J43)

Page 18

2.16 SMDC Connector (J45) Page 18

2.17 Onboard VGA Enable / Disable Jumper (J46) Page 19

2.18 Onboard Gigabit Ethernet Enable / Disable Jumper (J52) Page 19

2.19 Onboard 10/100 Ethernet Enable / Disable Jumper (J60) Page 20

2.20 ZCR Card Connector Select Jumper (J61) Page 20

2.21 CPU_1 Fan Connector (P1_FAN) (J5) Page 21

2.22 CPU_2 Fan Connector (P2_FAN) (J47) Page 21

2.23 FAN 1 Chassis Fan Connector (J44) Page 22

2.24 FAN 2 Chassis Fan Connector (J48) Page 22

2.25 FAN 3 Chassis Fan Connector (J4) Page 23

2.26 FAN 4 Chassis Fan Connector (J9) Page 23

2.27 FAN 5 Chassis Fan Connector (J3) Page 24

2.28 OEM Reserved Connectors and Jumpers Page 24

2.29 Installing the Processor(s) Page 25

2.30 Heatsink Retention Frame Installation Page 25

2.31 Thermal Interface Material Page 26

2.32 Heatsink Installation Procedures Page 27

2.33 Finishing Installing Heatsink Page 28

2.34 Tips on Installing Motherboard in Chassis Page 29

2.35 Installing the Memory Page 30

2.36 Attaching Drive Cables Page 32

2.37 Installing Add-In Cards Page 34

2.38 PCI Riser Cards Supported on S2882 K8S Page 35

2.39 Connecting External Devices Page 35

2.40 Installing the Power Supply Page 36

2.41 Finishing Up Page 36

http://www.TYAN.com

3

Chapter 3: BIOS

3.00 BIOS Setup Utility Page 37

3.01 BIOS Menu Bar Page 38

3.02 BIOS Legend Bar Page 38

3.03 BIOS Main Menu Page 39

3.04 BIOS Advanced Menu Page 40

3.05 BIOS PCI/PnP Menu Page 54

3.06 BIOS Boot Settings Menu Page 56

3.07 BIOS Security Menu Page 62

3.08 BIOS Chipset Setting Menu Page 63

3.09 BIOS Power Menu Page 69

3.10 BIOS Exit Menu Page 70

Chapter 4: Diagnostics Page 71

Appendix I: Glossary

Page 72

Appendix II: SMDC Information

Page 77

Technical Support

Page 78

http://www.TYAN.com

4

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder K8S Pro motherboard

1x 34-Pin floppy drive cable

1x LVD SCSI cable (if optional SCSI included)

4 x SATA cable

2 x SATA Drive Power Adapter

2 x Ultra-DMA-133/100/66 IDE cable

1 x Cable set: 9-pin Serial and 25-pin Parallel

1 x Thunder K8S Pro user’s manual

1 x Thunder K8S Pro Quick Reference guide

1 x TYAN driver CD

1 x SCSI driver diskette (if optional SCSI included)

1x Silicon Image SiI3114 SATA RAID driver diskette

1x Silicon Image SiI3114 SATA Link driver diskette

1 x I/O shield

2 x CPU Retention Frame

If any of these items are missing, please contact your vendor/dealer for replacement

before continuing with the installation process.

http://www.TYAN.com

5

Chapter 1: Introduction

Congratulations

You are now the owner of the ideal solution for rackmount servers, large computer

clusters, or pedestal server needs. The Tyan Thunder K8S Pro features support for Dual

AMD Opteron processor(s), two channel Gigabit Ethernet, one 10/100 Ethernet and Serial

ATA (SATA).

Remember to visit TYAN’s Website at http://www.TYAN.com

. There you can find

information on all of TYAN’s products with FAQs, online manuals and BIOS upgrades.

Hardware Specifications

Processor

● Dual

µ

PGA 940-pin ZIF sockets

● Supports up to two AMD Opteron

™

processors

● Onboard VRM, 4-phase PWM

● 128-bit DDR dual-channel memory

controller integrated in CPU

Chipset

● AMD-8131

™

HyperTransport

™

PCI-X

Tunnel

● AMD-8111

™

HyperTransport

™

I/O Hub

● Winbond W83627HF Super I/O chip

● Analog Devices ADM1027 Hardware

Monitoring IC

Memory

● 128-bit DDR dual-channel memory bus

● Total eight 184-pin 2.5-Volt DDR DIMM

sockets (4 on CPU1 and 4 on CPU2)

● Supports up to 16 Gigabyte Registered

DDR

● Supports ECC type memory modules

● Supports PC3200

*

, PC2700, PC2100

and PC1600 DDR

* NOTE:

With Opteron 246 C-stepping

CPU and above.

Expansion Slots

● 2 Independent PCI-X buses from AMD-

8131

−

PCI-X bridge A supports 64-bit

100 / 66 / 33 MHz with two 3.3-Volt

PCI-X slots

−

PCI-X bridge B supports 64-bit 133 /

100 / 66 / 33 MHz with two 3.3-Volt

PCI-X slots

● One legacy 32-bit 33MHz PCI slot (5v)

from AMD-8111

● Total of five usable slots

Integrated Enhanced IDE

Controller

● Provides two IDE dual-drive ports

for up to four IDE devices

● Supports up to ATA-133 IDE

devices

Integrated I/O

● One floppy, Two serial (one

header and one connector), and

one parallel header

● PS/2 KB/Mouse connectors

● Total four USB connections (2 I/O

panel, rear connectors and 2 USB

headers)

System Management

● Total six 3-pin fan headers with

tachometer monitoring

● Three fan headers with PWM

control

● 2-pin Chassis Intrusion header

● Temperature, voltage and fan

monitoring

Integrated SATA Controller

● Silicon Image SiI3114 SATA RAID

● Supports SATA 1.0 Specification

● Supports 4 channel SATA port for

up to four SATA devices

● Supports RAID 0, 1, 0+1

● Connected to legacy 32-bit 33MHz

PCI bus

http://www.TYAN.com

6

Integrated PCI Graphics

● ATI



Rage

TM

XL PCI graphics controller

● 8MB Frame Buffer of video memory

Integrated LAN Controllers

● Two Broadcom

®

BCM5704C dual-

channel Gigabit Ethernet controller

● Two RJ-45 LAN connectors with LEDs

● Connected to PCI-X Bridge A

● Three Front Panel LED headers

● One Intel

®

82551QM 10/100 Ethernet

controller (Optional)

● Stacked USB 1.1 (two) ports and RJ45

LAN port on top

Intelligent Platform Management

Interface Header

● Tyan Server Management Daughter

cards (optional); supports features

listed below via IPMI header

● QLogic™ Zircon Baseboard

Management Controller (BMC) based

on powerful ARM7 technology

● Tailored for IPMI highest 1.5 Spec.

● Supports KCS and BT styles

● Flexible Windows or Linux Management

Solution

● Supports RMCP and SNMP protocols

● Supports ASF standard and EMP

● I

2

C serial multi-master controllers and

UARTs

● Built-in IPMB connector

● Remote power on/off and reset support

(IPMI-over-LAN)

Integrated Dual Channel SCSI

(manufacturing option)

● Adaptec AIC7902W Dual-

Channel U320 SCSI controller

● Connects to PCI-X Bridge A

Adaptec



Zero Channel RAID

ready

BIOS

● AMI

®

BIOS 8.0 on 4Mbit LPC

Flash ROM

● Supports ACPI 1.0b & 2.0

● PnP, DMI2.0, WfM2.0 Power

Management

● Power Management S1, S4 and

S5 support

Form Factor

● Extended ATX footprint

(13” x 12” 330.2 x 304.8 mm)

● EPS12V (24pin + 8pin) power

connectors

● 4-pin auxiliary power connector

● Serial (one) and VGA (one)

connectors

● Stacked USB 1.1 (two) ports and

RJ45 LAN port on top

● Stacked PS/2 keyboard and

mouse connectors

● Two RJ-45 side-by-side LAN

connectors with LEDs

Regulatory

● FCC Class B (Declaration of

Conformity)

● European Community CE

(Declaration of Conformity)

Software Specifications

OS (Operating System) Support

Microsoft Windows NT 4.0 + Service Pack 6A

Microsoft Windows 2000

Microsoft Windows XP

Microsoft Windows Server 2003

SuSE Server 8.0 for AMD-64

Turbo Linux for AMD-64

Red Hat 7.3, 8.0, and 9.0

Other distributions of Linux pending validation

TYAN reserves the right to add support or discontinue support for any OS with or without

notice.

http://www.TYAN.com

7

Chapter 2: Board Installation

Precaution: The Thunder K8S Pro supports EPS12V power supplies (24-pin/8-pin) and

will not operate with any other types.

DO NOT

USE

ATX 2.x, ATX12V or ATXGES power supplies as they will damage the

board and void your warranty.

How to install our products right… the first time

The first thing you should do is read this user’s manual. It contains important information

that will make configuration and setup much easier. Here are some precautions you

should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic

bag. Unplug the power from your computer power supply and then touch a

safely grounded object to release static charge (i.e. power supply case). For the

safest conditions, TYAN recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or

flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory

modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag

that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis,

as well as installing the processor, memory, disk drives and cables.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.TYAN.com

8

2.00 – Board Image

This picture is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above

picture.

The following page includes details on the vital components of this motherboard.

http://www.TYAN.com

9

2.01

–

Block Diagram

Thunder K8S Pro S2882 Block Diagram

AMD

Opteron

TM

Processor

AMD

AMD-8131

AMD

AMD-8111

Winbond

W83627F/HF

LPC Super I/O

Floppy Disk Drive

Intel-82551

10/100

(Optional)

16x16 Hyper Transport@1600MT/s

AMD Chipset

LPC

AMD

Opteron

TM

Processor

32-Bit/33MHz

ATI RAGE XL

8MB

Silicon Image

SiI3114

16x16 Hyper Transport@1600MT/s

PCI

Slot

ADM1027

Hardware

monitor

LPC

ROM

PS/2 Keyboard &

Mouse

Parallel Port x 1

EIDE(ATA/133) x2

USB 1.1 x2

LINK 0B

OUT

IN

OUT

LINK 0A

LINK 1

8x8 ncHyper Transport@400MT/s

IN OUT

2 to header

IN

200-333MT/s

144-Bit

184 pin

DIMM0

184 pin

DIMM1

184 pin

DIMM2

184 pin

DIMM3

Adaptec

AIC-7902 SCSI

BCM5704C

Gigabit LAN

64-Bit/100/66MHz

PCI-X Slot

(PCI4 / ZCR)

SO-DIMM144

(ZCR)

PCI-X Slots

184 pin

DIMM2

184 pin

DIMM1

184 pin

DIMM0

184 pin

DIMM3

144Bit

USB 1.1 x 2

USB Ports: 2 to backplane

200-333MHz

4 X Serial ATA

RAID Ports

150MB/s

Serial Port x 2

64-Bit/133/100MHz

*ZCR support with Adaptec

PCI or SO-DIMM ZCR card

(Optional)

http://www.TYAN.com

10

2.02 – Board Parts, Jumpers and Connectors

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1 (Bottom)

LAN3 (Top)Optional

KB(Bottom)

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)

J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

http://www.TYAN.com

11

Jumper Function Settings

J1 / J2

Gigabit Ethernet LAN_1 &

LAN_2 Front Panel LED Header

See Section 2.03 for pinout

configuration

J6

Front Panel Connector

See Section 2.04 for pinout

configuration

J8 Clear CMOS Jumper

1-2 Close:

Normal mode (Default)

2-3 Close: Clear CMOS mode

J11 SMBus_0 Connector

See section 2.06 for pinout

configuration

J12

USB Connector header

For front or rear chassis mount USB

connectors

J17

10/100 Ethernet LAN3

Front Panel LED Header

See Section 2.08 for pinout

configuration

J19

Chassis Intrusion Connector

See Section 2.09 for pinout

configuration

J22

SO-DIMM Socket See Section 2.10

J23

COM2 Header See Section 2.11 for pinout

J24 / J39

PCI-X Bridge B (PCI 1 & PCI 2)

PCI-X Speed Select Jumper

133MHz: J24 & J39 open (Default)

100MHz: J24 close; J39 open

66MHz: J24 & J39 close

J41

PCI-X Bridge A (PCI3 & PCI4)

force PCI Mode Jumper

Open

: PCI-X mode (Default)

Close: PCI mode

J42

KEYLOCK

Keylock Enable/Disable Jumper

Open: Enable PS/2 keyboard

(Default)

Close: Disable PS/2 keyboard

J43

PCI-X Bridge A (PCI 3 & PCI 4 &

SCSI7902 & BCM5704) PCI-X

Speed Select Jumper

Open: up to PCI-X 100MHz (Default)

Close: PCI-X 66MHz

J45 SMDC Connector See Appendix II SMDC information

J46

Onboard VGA Enable/Disable

Jumper

1-2 Close: Enable (Default)

2-3 Close: Disable

J52

Onboard Gigabit Ethernet

Enable/Disable Jumper

Open: Disable

Close: Enable (Default)

J60

Onboard 10/100 Ethernet

Enable/Disable Jumper

1-2 Close: Enable (Default)

2-3 Close: Disable

J61

(Optional)

ZCR Card Connector Select

Enable/Disable Jumper

1-2 Close: PCI4 slot Enable

2-3 Close

: SO-DIMM Connector

Enable (Default)

P1_FAN

(J5)

CPU_1 Fan Connector With speed, MAX 2.0A

P2_FAN

(J47)

CPU_2 Fan Connector With speed, MAX 2.0A

FAN1

(J44)

Chassis Fan Connector With speed control, MAX 3.0A

FAN2

(J48)

Chassis Fan Connector With speed control, MAX 2.0A

FAN3

(J4)

Chassis Fan Connector With speed control, MAX 3.0A

FAN4

(J9)

Chassis Fan Connector With speed, MAX 2.0A

FAN5

(J3)

Chassis Fan Connector With speed, MAX 2.0A

http://www.TYAN.com

12

Jumper Legend

OPEN - Jumper OFF without jumper

CLOSED - Jumper ON with jumper

2.03 –Gigabit LAN_1 Front Panel LED Header (J1) and

Gigabit LAN_2 Front Panel LED Header (J2)

14

Pin_4 Pin_3 Pin_2 Pin_1

Green -

Green +

Yellow -

Yellow +

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W836 27HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W836 27HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

Green LED solid= 10Mb link

Green LED flashing= 10Mb activity

Yellow LED solid= 100Mb link

Yellow LED flashing= 100Mb activity

Both LED Solid= Gigabit link

Both LED flashing= Gigabit activity

2.04 – Front Panel Connector (J6)

2 1

18 17

PWR-LED

RESET

INFRARED

HD-LED

POWER

SPEAKER /

BUZZER

Function PIN PIN Function

Speaker- /

Buzzer-

18 17 NC

Buzzer+

16 15

IRTX

NONE

14 13

GND

Speaker+ 12 11 IRRX

NC

10

9

+5V

GND

8 7

Reset SW+

PWR+

6 5

GND

Power LED-

4 3

HDD LED-

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD -8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bottom)

Mou se(Top )

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

Power

LED+

2 1

HDD LED+

http://www.TYAN.com

13

2.05 – Clear CMOS Jumper (J8)

3

1

Default

3

1

Clear

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1 (Bott om)

LAN3 (Top)Optional

KB( Bottom )

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

You can reset the CMOS settings by

using this jumper if you have forgotten

your system/setup password or need to

clear system BIOS setting.

-

Power off system and disconnect

both power connectors from the

motherboard

-

Use jumper cap to close Pin_2 and

Pin_3 for several seconds to Clear

CMOS

-

Put jumper cap back to Pin_1 and

Pin_2 (default setting)

Reconnect power & power on system

2.06 – SMBus_0 Connector (J11)

Pin # Signal Description

4

NC

3 SMBUS_CLK

2 GND

1

4

1

SMBUS_DATA

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bottom

)

LAN3

(

Top

)

Optional

KB(Bottom)

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

Use this connector to connect external

SMBUS devices

http://www.TYAN.com

14

2.07 – USB Connector Headers (J12)

1

9

2

10

Signal

Description

Pin # Pin #

Signal

Description

+5V

1 2

+5V

Data -

3 4

Data -

Data + 5 6 Data +

GND

7 8

GND

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1 (Bott om)

LAN3 (Top)Optiona l

KB(Bot tom)

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX- A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI- B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX- A

PCIX- B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

GND

9 10

GND

2.08 – 10/100 LAN Front Panel LED Header (J17)

41

Pin_1 Pin_2 Pin_3 Pin_4

Yellow +

Yellow -

Green +

Green -

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD -8111

PRI-IDE

SEC- IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bottom)

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Opti ona l)

J6

J41

1

J61

Green LED solid= 10Mb link

Green LED flashing= 10Mb activity

Yellow LED solid= 100Mb link

Yellow LED flashing= 100Mb activity

http://www.TYAN.com

15

2.09 – Chassis Intrusion Connector (J19)

1

Pin-1

Intrusion detection

Pin-2

GND

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

For use with chassis that support

this feature

2.10 – SO-DIMM Socket (J22)

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD -8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1 (Bott om)

LAN3 (Top)Optional

KB( Bottom )

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Opti ona l)

J6

J41

1

J61

This socket is capable of accepting the

Adaptec Zero Channel RAID card.

Compatible with Adaptec ASR-2015S

(ZCR)

http://www.TYAN.com

16

2.11 – COM2 Header (J23)

1 9

2 10

Signal

Description

Pin# Pin#

Signal

Description

NC/KEY

10 9

GND

(Ground)

RI (Ring-

Indicator)

8 7

DTR (Data-

Terminal-

Ready)

CTS (Clear-

to-Send)

6 5

TX

(Transfer-

Data)

RTS

(Request-

to-Send)

4 3

RX

(Receive-

Data)

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top )

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

DSR (Data-

Set-Ready)

2 1

DCD

(Data

Carrier

Detect)

2.12 – PCI-X Bridge B (PCI 1 & PCI 2) PCI-X Speed Select Jumper (J24 / J39)

Speed

1

133MHz J24 / J39

100MHz J39 J24

66MHz J24 / J39

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

Allows PCI-X Bridge B to operate at up

to 133MHz (For use with one PCI-X

133 device)

Tyan recommends using PCI-X Slot

1 for 133MHz support

http://www.TYAN.com

17

2.13 – PCI-X Bridge A (PCI 3 & PCI 4) force PCI Mode Jumper (J41)

1

OPEN

(Default)

Allows PCI 3 and PCI 4 to operate in

PCI-X Mode

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED

To force PCI 3 and PCI 4 to operate in

PCI compatible mode. Close this

jumper if the card you are using does

not support PCI-X.

2.14 – Keylock Enable/Disable Jumper (J42)

1

OPEN

(Default)

Enable PS/2 keyboard

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED

Disable PS/2 keyboard

http://www.TYAN.com

18

2.15 – PCI-X Bridge A (PCI 3 & PCI 4 & SCSI7902 & BCM5704) PCI-X Speed Select

Jumper (J43)

1

OPEN (Default)

Allows PCI-X Bridge A (PCI 3 & PCI 4

& SCSI7902 & BCM5704) to operate

at up to 100MHz

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optional

KB(Bott om)

Mouse (Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2 _LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED

Sets PCI-X Bridge A (PCI 3 & PCI 4 &

SCSI7902 & BCM5704) to operate at

a maximum 66MHz

Note

: Due to the PCI-X specifications

it will be necessary to set this bus to

66MHz if a 133/100MHz PCI-X card is

added to this bus.

2.16 –SMDC Connector (J45)

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD -8111

PRI-IDE

SEC-IDE

Winb ond

W83627HF

BT1

AMD

AMD-8131

USB1 (Bott om)

LAN3 (Top)Optional

KB( Bottom )

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI-B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Opti ona l)

J6

J41

1

J61

Connect Server Management Daughter

Card (SMDC) (Ref. Appendix II)

Compatible with Tyan M3289 (SMDC)

http://www.TYAN.com

19

2.17 – Onboard VGA Enable/Disable Jumper (J46)

3

1

CLOSED: 1 - 2 (Default)

To enable onboard ATI Rage XL

Graphic chip

3

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD- 8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bott om

)

LAN3

(

Top

)

Optiona l

KB(Bott om)

Mouse(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI- B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED: 2 - 3

To disable onboard ATI Rage XL

Graphic chip

2.18 – Onboard Gigabit Ethernet Enable/Disable Jumper (J52)

1

OPEN

To disable onboard Gigabit Ethernet

(Both ports)

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD-8111

PRI-IDE

SEC-IDE

Winbond

W836 27HF

BT1

AMD

AMD-8131

USB1 (Bot tom)

LAN3 (Top)Optional

KB(Bo ttom)

Mou se(Top)

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT 1

FDD

SCSI

7902

COM2

SCSI-A SCSI -B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED

(Default)

To enable onboard Gigabit Ethernet

(Both ports)

http://www.TYAN.com

20

2.19 – Onboard 10/100 Ethernet Enable/Disable Jumper (J60)

13

CLOSED: 1 – 2

(Default)

To enable onboard 10/100 Ethernet

3

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD -8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bottom

)

LAN3

(

Top

)

Optional

KB(Bottom)

Mou se(Top )

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI- B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED: 2 – 3

To disable onboard 10/100 Ethernet

2.20 –ZCR Card Connector Select Jumper (J61) (Optional)

3

1

CLOSED: 1 – 2

To enable PCI4 slot is capable of

accepting the Zero Channel RAID

card

3

1

J55

KB-MS

J54

USB1

CPU2_FAN

J29

J3

FAN5

BIOS

AMD

AMD -8111

PRI-IDE

SEC-IDE

Winbond

W83627HF

BT1

AMD

AMD-8131

USB1

(

Bottom

)

LAN3

(

Top

)

Optional

KB(Bottom)

Mou se(Top )

1

LAN1_LED

USB2

SATA4

SATA3

CPU2

PCIX-A

PCI5

CMOS

CH-A

J47

J12

J8

J50

LAN2

J58

LAN1

J57 (COM1)J56 (VGA)

CPU1

1

J44

FAN 1

SATA2

SATA1

LAN1/2

LAN3

ATI

RAGE XL

LPT1

FDD

SCSI

7902

COM2

SCSI-A SCSI- B

1

J9

FAN4

INTRUDER

LAN3_LED

CH-B

LAN2_LED

J5

CPU1_FAN

J48

FAN 2

KEYLOCK

PCIX-A

PCIX-B

ZCR J22

1

J45

SMDC

Bz1

J23

J4

FAN3

J17

J19

J1

J2

J24

J39

J46

J43

J11

J60

J52

1

PCI4 PCI3 PCI2 PCI1

J25

(Optional)

J6

J41

1

J61

CLOSED: 2 – 3

(Default)

To enable SO-DIMM Socket (J22) is

capable of accepting the Zero

Channel RAID card

La pagina sta caricando ...

Tyan S2882 Manuale utente

Questo manuale è adatto anche per

Tyan S2882 Manuale utente

in altre lingue

Documenti correlati

Altri documenti