Kong 911 Armor Manuale utente

EN

Regulation (EU)

2017/745

911 ARMOR

880.07

2

Original version in Italian dated 17/10/2023

Download the digital version - Scarica la versione digitale

880.07 911 ARMORwww.kong.it

3

Original version in Italian dated 17/10/2023

INDEX

1 - SYMBOLS AND SUPPORT 4

1.1 Symbols 4

1.2 Technical assistance 4

2 - GENERAL INFORMATION 5

3 - TECHNICAL FEATURES 6

3.1 Part terminology and materials 6

3.2 Technical data 7

3.3 Optional components and spare parts 7

4 - SPECIFIC INFORMATION 9

4.1 Application 9

4.2 Assembly 9

4.3 Positioning and immobilising the patient 11

4.4 Transporting the patient 12

5 - MAINTENANCE AND REPAIR 14

5.1 General Information 14

5.2 Maintenance 14

5.3 Repair 14

6 - STORAGE 15

7 - CHECKS, INSPECTIONS AND REVISIONS 16

7.1 Checks 16

7.2 Inspections 16

7.3 Revisions 16

8 - DURATION AND WARRANTY 17

8.1 Duration 17

8.2 Disposal 17

8.3 Warranty 17

8.4 Law obligations 17

9 - LABELLING AND SYMBOLS 18

9.1 Medical Device Label 18

9.2 Symbols 18

10 - DOCUMENTS 19

10.1 Inspections and servicing register 19

10.2 Maintenance and repair records 20

10.3 EU Declaration of conformity 21

11 - LIST OF APPLIED AND REFERENCE STANDARDS 22

11.1 Applied standards 22

11.2 Standards used as reference 23

4

Original version in Italian dated 17/10/2023

CHAPTER

For the sake of comfort and clarity while reading this manual, below are the symbols used

for handling important warnings for a proper and safe use of the device.

1.1

SYMBOLS

REQUIREMENT FOR PROPER USE

It identiﬁes the presence of information for proper use of the device.

INFORMATION REQUIREMENT

It identiﬁes the presence of useful and general information which guides

the reader towards a conscious use of the device and/or performance of

actions.

It identiﬁes that the Medical Device is manufactured, designed and produ-

ced in compliance with the provisions of the General Safety and Perfor-

mance Requirements of Regulation (EU) 2017/745 (Class I medical device,

in compliance with classiﬁcation rule 1 as indicated in the attachment VIII).

1

SYMBOLS

AND SUPPORT

For information please contact Kong Customer Support Service by:

- telephone +39 0341 630506

- fax +39 0341 641550

- email: [email protected]

or write to KONG S.p.A. – Via XXV Aprile, 4 – 23804 Monte Marenzo LC - ITALY.

To facilitate support operations, please always communicate or state the serial number (SN)

indicated on the label ﬁxed to the Medical Device.

1.2

SUPPORT

880.07 911 ARMORwww.kong.it

5

Original version in Italian dated 17/10/2023

Warning: not suitable for

use in an ATEX environment

(Directive 94/9/CE)

The information provided by the manufacturer

(hereinafter referred to as information)

must be read and clearly understood by

the user prior to using the Medical Device

(MD hereafter). The information regards the

description of the features, performance,

assembly, disassembly, maintenance,

preservation, disinfection, etc. of the device.

Even though the information offers tips on

use, this information shall not be considered

as a user manual under actual conditions of

use.

WARNINGS AND

LIMITATIONS OF USE:

- this device shall be strictly used by people

who are physically ﬁt, trained (instructed

and taught) to use the device and with

speciﬁc experience regarding moving

the patient or, during training activities,

by people under direct supervision of the

trainers/ supervisors who guarantee the

safety thereof,

- do not use the device before fully reading

and understanding this user manual,

- strictly follow the manufacturer’s

information, improper use of the device is

hazardous,

- modifying and/or repairing the device is

strictly forbidden,

- all checks described in chapter 7

must be carried out prior to and

after using the device. In case of any

doubt on the efficiency of the device,

the user must replace it immediately,

- non-compliant use, deformations, falls,

wear, chemical contamination, exposing

textile/plastic components/devices

to temperature below -30°C or above

2

GENERAL INFORMATION

+50°C and metal components/devices to

temperatures exceeding 100°C are some

examples of causes that can reduce, limit

and end the life of the device,

- Prior to any rescue operation, be keen

not to exceed the capacity indicated in

paragraph 3.3,

- in order to reduce risks of exposure to /

transmission of infectious diseases, clean

and disinfect the device as indicated in

chapter 5,

- improper use of the patient immobilisation

systems can jeopardise the safety of the

patient,

- always check the compatibility of the

devices used alongside the device by

consulting the relative manufacturer’s

information,

- use of spare parts or optional components

different from the ones indicated in

paragraph 3.4 can be hazardous,

- do not expose the device to sources of heat

and at contact with chemical substances.

Reduce exposure to direct sunlight as

much as possible. At low temperatures

and in the presence of humidity, formation

of ice could reduce ﬂexibility and increase

cutting and abrasion-related risks on

textile and synthetic devices,

- Report to the manufacturer and the

competent authority of the member

state where the user and / or patient is

established any serious incident occurring

in relation to the MD.

All our devices are tested/ checked piece

by piece in compliance with the procedures

laid down by the Quality System certiﬁed

in accordance with the UNI EN ISO

9001 standard. Laboratory tests, testing,

information and standards do not always

reproduce the practical result. Thus, the

results obtained under the actual conditions

of use of the device in the natural environment

may differ, even considerably at times.

The best information lies in the continuous

practical use under the supervision of skilled/

expert/qualiﬁed people.

CHAPTER 2

6

Original version in Italian dated 17/10/2023

A – Aluminium alloy frame, can be disassembled into two parts,

B – Protective shells made of HDPE,

C – Polyurethane foam mats,

D – Polyester webbing for physically securing patient,

E – Polyester webbing for ﬁxing the mats,

F – ARIES hanging kit.

Fig.1

F

B

A

B

D

E

D

C

TECHNICAL

FEATURES

3.1 TERMINOLOGY AND MATERIALS OF THE PARTS

CHAPTER 3

880.07 911 ARMORwww.kong.it

7

Original version in Italian dated 17/10/2023

3.2 TECHNICAL DATA

Length without handles: 198 cm

Width: 60 cm

Overall weight (ﬁg.1): 9,6 kg

Capacity: 300 kg*

Fig.2

3.3 OPTIONAL COMPONENTS AND SPARE PARTS

3.3.1 Optional components

The methods of connection and use of the optional components are deﬁned in the relative

user instructions.

880060KITKK HANDLE KIT

Handles with quick coupling for carrying the stretcher.

X4

*For helicopter hoisting and lowering operations, given the 1:14 safety factor, the capacity

is reduced to 150 kg.

8

Original version in Italian dated 17/10/2023

C – Mats.

3.3.2 Spare parts

C

Fig.5

Fig.3

880020300KK FLOK-IT

Floating kit for stretchers, made of three cylinders of different lenghts (1 m for the sides - 0,4

m head side) , each of one equipped with two fastening straps with quick release buckles.

Fig.4

880.07 911 ARMORwww.kong.it

9

Original version in Italian dated 17/10/2023

4.2 ASSEMBLY

The “911 ARMOR” stretcher is a MD particularly suitable for recovering and transporting a

patient, which may also be immobilized on the “X-TRIM” spinal boards or the vacuum mattress

“VACUUM.” All decisions regarding movement and immobilization of the patient, as well as

the duration of these operations, the methods to be adopted and use in conjunction with other

devices, must be taken and implemented by expert, trained personnel only.

The ARIES hanging kit (F), makes the “911 ARMOR” stretcher capable of being lifted by

helicopter.

Assemble the two parts of the structure in the following steps:

a) bring the two halves closer together

(ﬁg. 6),

Fig.6

SPECIFIC

INFORMATION

4.1 INTENDED USE

CHAPTER 4

10

Original version in Italian dated 17/10/2023

b1

b2

b) lift the two parts centrally and insert the pins into the cylinders (ﬁg. 7),

c) fully tighten the two ring nuts (ﬁg. 8).

Fig.7

Fig.8

880.07 911 ARMORwww.kong.it

11

Original version in Italian dated 17/10/2023

4.3 POSITIONING AND SECURING THE PATIENT

With the stretcher positioned on a ﬂat, stable surface:

a) unhook the buckles and open the securing straps (ﬁg. 9),

b) lay the patient in the stretcher, hook on the buckles and tension the straps until they secure

the patient (ﬁg. 10).

This procedure must also be used for patients immobilized on the “X-TRIM” spinal board or on

the “VACUUM” vacuum mat.

Avoid prolonged contact of the patient’s skin with the fabrics of the device

Fig.9

Fig.10

12

Original version in Italian dated 17/10/2023

4.4 TRANSPORTING THE PATIENT

Fig.11

Before any recovery operation, make sure that the weight does not exceed

the capacity deﬁned above!

The “911 HIVE” stretcher is suitable for use in the following modes of use:

• Manual transport (ﬁg. 11)

• Transport with the handles (ﬁg. 2)

with kit 880060KITKK (optional components)

• Lifting and lowering with rescue devices (ﬁg. 12)

with the 880070100KK ARIES hanging kit

• Hoisting and lowering with helicopters (ﬁg. 12)

with the 880070100KK ARIES hanging kit

• Transport on slopes (sec. 4.4.2)

• River transportation (ﬁg. 4)

with the 880020300KK FLOK-IT kit (L)

880.07 911 ARMORwww.kong.it

13

Original version in Italian dated 17/10/2023

4.4.1 Connection with the included hanging kit

a) Connect the hanging kit to the appropriate holes on the side of the stretcher using the

eight connectors, while respecting the head-foot coupling indicated on the webbing,

b) screw the connector nuts in completely.

Fig.12

Fig.13

4.4.2 Transport on slopes

For lowering and retrieving on slopes up to 45°, it is possible to connect the restraining rope

to the head of the stretcher, taking care to connect the two highlighted points (ﬁg. 13) with

appropriate devices so as to distribute the load equally. Any knots or connecting devices

are at the discretion and responsibility of the stretcher operators, who must be properly

trained.

H

14

Original version in Italian dated 17/10/2023

Repair shall be strictly carried out by the manufacturer.

The user is allowed to replace the parts mentioned in paragraph 3.4.2 only,

with new and genuine parts.

The “ARMOR” stretcher is made of material which is highly resistant to wear and external

agents. Despite this, the use conditions require maintenance operations and even repair in

particular conditions.

MAINTENANCE

AND REPAIR

5.1 GENERAL INFORMATION

5.2 MAINTENANCE

5.3 REPAIR

CHAPTER 5

Maintenance and repair operations must be recorded in a special register,

an example of which is indicated in chapter 10.

The maintenance operations that must be carried out by the user are,

in order:

a) cleaning: after every use, wash with warm (max. 40 C) potable water, possibly adding a

neutral detergent (e.g. Marseille soap). Rinse and leave to dry in a shaded place, away

from direct sources of heat,

b) disinfection, when deemed necessary or after prolonged inactivity (more than 21 days),

preceded by cleaning: wipe with a clean cloth , soaked in a water solution of sodium

hypochlorite (bleach) with a 0,1% concentration (1000 ppm). When blood or other bodily

ﬂuids are present, the recommended concentration of sodium hypochlorite is 0,5%

(5000ppm).

880.07 911 ARMORwww.kong.it

15

Original version in Italian dated 17/10/2023

After cleaning, any disinfection and drying operations, keep the product and its accessories

in a place that is dry (relative humidity 40-90%), cool (temperature 5-40° C) and safe

(avoid UV radiation), chemically neutral (absolutely avoid salty and/or acid environments),

away from sharp edges, sources of heat, humidity, corrosive substances or other possible

jeopardising conditions.

Do not store this device wet!

6 STORAGE

CHAPTER 6

16

Original version in Italian dated 17/10/2023

Before and after every use, check the device and ensure that:

- it is appropriate for the use it was intended for,

- it has not been subjected to mechanical deformations and it neither has cracks nor shows

signs of wear,

- the textile parts do not have cuts, burns, chemical products residues, excessive hair,

wear, in particular check areas at contact with the metal components (buckles, rings, etc.);

- the markings, including labels, are legible.

The device must be inspected at least once a year, starting from the date of ﬁrst use, by

expert personnel trained and approved by KONG S.p.A. The date of the ﬁrst use and the

outcome of the inspection must be recorded in the Inspections and Servicing Register,

regarding which an example is indicated in chapter 10.

The device must be serviced by KONG S.p.A., or by expert personnel trained and approved

by KONG S.p.A. if:

- any malfunctions are detected,

- the result of the pre and post use check or of the inspections is negative.

The outcome of the servicing must be recorded in the Inspections and Servicing Register,

regarding which an example is indicated in chapter 10.

The revised device is guaranteed for one year from the revision date.

CHECKS, INSPECTIONS

AND REVISIONS

7.1 CHECKS

7.2 INSPECTIONS

7.3 REVISIONS

CHAPTER 7

880.07 911 ARMORwww.kong.it

17

Original version in Italian dated 17/10/2023

DURATION

AND WARRANTY

Carefully read the “Warnings and limitations of use” paragraph in chapter 2.

The duration of this device depends on the outcome of the at least one-yearly inspection

(paragraph 7.2) and possible servicing.

The suspension, even if not used, has a maximum duration of 10 years from the date of

manufacture indicated on the label.

8.1 DURATION

Follow the rules in force in the country of use and the waste disposal procedures of the

reference hospital facility for proper disposal.

8.2 DISPOSAL

The manufacturer guarantees the compliance of the device with the regulations in force

at the time of production. Warranty covering defects is limited to defects regarding raw

materials and manufacturing defects. The warranty does not cover normal wear, oxidation,

damage caused by non-compliant use and/or in competition, improper maintenance,

transportation, preservation or storage. Warranty will be immediately deemed null and void

should the device be modiﬁed or tampered with. Validity corresponds to the legal validity

of the country where the device was sold, as from the date of sale, by the manufacturer.

No claims shall be raised against the manufacturer once the aforementioned period has

expired. Any repair or replacement request under warranty must be accompanied by a

proof of purchase. Should the defect be recognised, the manufacturer undertakes to repair

or, replace or refund the device at his discretion. The manufacturer shall not be held liable

beyond the invoice price of the device in any case whatsoever.

8.3 WARRANTY

Important: any devices that have not passed the pre-use, post-use and

periodic inspection must be eliminated and made unusable.

CHAPTER 8

Professional and free time activities are often regulated by special national laws which can

impose limits and/or obligations concerning the use of these devices. The user has the

obligation to know and apply such laws which could provide for limits different from those

indicated in this information.

8.4 LAW OBLIGATIONS

18

Original version in Italian dated 17/10/2023

UDI

MD

ITALY

2022 / 01

880.07 - MOD. 911 ARMOR

(01)08023577071237(21)1234561234

KONG S.p.A.

Via XXV Aprile, 4

I - 23804 MONTE MARENZO (LC) - ITALY

Tel. +39 0341 630506

123456 1234

LABELLING

AND SYMBOLS

CHAPTER 9

Identiﬁcation and traceability

9.1 MEDICAL DEVICE LABEL

9.2 SYMBOLS

Any changes to the positioning of the symbols does not change the content thereof.

Manufacurer's identification

Product identification code

Unique serial number

Country, year and month of production.

Unique Device Identifier

Medical Device

Consult the user manual

Compliant with Regulation (EU) 2017/745

UDI

MD

ITALY

YYYY / MM

Manufacurer's identification

Product identification code

Unique serial number

Country, year and month of production.

Unique Device Identifier

Medical Device

Consult the user manual

Compliant with Regulation (EU) 2017/745

UDI

MD

ITALY

YYYY / MM

Information and safety

Data matrix UDI

Readable with the Apps:

iGepir - BarValid - Barcode Scanner

880.07 911 ARMORwww.kong.it

19

Original version in Italian dated 17/10/2023

STRETCHER – Class I MD

REF. 880.07 MOD. 911 ARMOR

UDI-DI 08023577071237 SN

Date of ﬁrst use

INSPECTIONS AND SERVICING

DATE I/S Description Outcome Supervisor

DOCUMENTS

CHAPTER

10

10.1 INSPECTIONS AND SERVICING REGISTER

20

Original version in Italian dated 17/10/2023

STRETCHER – Class I MD

REF. 880.07 MOD. 911 ARMOR

UDI-DI 08023577071237 SN

Date of ﬁrst use

10.2 REGISTRO MANUTENZIONI E RIPARAZIONI

INSPECTIONS AND SERVICING

DATA M/R Description Outcome Supervisor

La pagina sta caricando ...

Kong 911 Armor Manuale utente

Kong 911 Armor Manuale utente

in altre lingue

Documenti correlati

Altri documenti