DTS FOS 100 POWER FULL RGBM Manuale utente

Made in Italy

FOS 100 POWER SOLO

FOS 100 POWER

User’s Manual rel 1.2 GB

D.T.S. Illuminazione s.r.l. – ITALY

http://www.dts-lighting.it

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i

diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto

per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche, funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked.

However, no responsibility will be taken for any errors. All rights are reserved and this

document cannot be copied, photocopied or reproduced, in part or completely, without

prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any

of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec

le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles

reproduit, dans sa totalité ou partiellement, sans le consentement préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline toute

responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamente redactadas

y controladas. Con todo, no se asume ninguna responsabilidad por eventuales

inexactitudes. Todos los derechos han sido reservados y este documento no puede ser

copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorización escrita

de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los productos

o de los circuitos descritos.

3

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- MAIN ELECTRICAL CHARACTERISTICS 6

6- ACCESSORIES 7

7- IMPORTANT SAFETY INFORMATION 10

7.1 Fire prevention

7.2 Prevention of electric shock

7.3 Safety

8- INPUT / OUTPUT CONNECTIONS 11

9- DMX SIGNAL CONNECTION 13

9.1 DMX Addresses

9.2 Selecting the DMX address

10- FIRMWARE UPDATING 15

11- DISPLAY FUNCTIONS 16

12- SERVICE MENU 20

13- DMX PROTOCOL 22

4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT

ON INFLAMMABLE SURFACES”

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE DEVICE

AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

F

!

10cm

5

4- TECHNICAL FEATURES

OVERVIEW

FOS 100 POWER is the most powerful model in the FOS line of compact LED bars,

designed for lighting and colouring large surfaces with a homogeneous projection.

FOS 100 POWER is ideal in a variety of applications, either indoor or outdoor, such as:

lighting building facades, monuments, public and commercial spaces; creating uniform

background colours and cycloramas, etc.

FOS 100 POWER is available in two versions.

FOS 100 POWER FULL COLOUR: 24 x Full Colour (RGBW) LEDs;

FOS 100 POWER RGBW: 96 x RGBW LEDs.

Three dedicated lenses sets (Spot, Medium flood, Wide flood) are available for each

model.

LED Technology

FOS 100 POWER FULL COLOUR:

24 x Full Colour (RGBW) LEDs; 7.028 Lux at 3 m;

16 million colours; linear colour temperature 2800°K – 6500°K

FOS 100 POWER RGBW:

96 x RGBW LEDs (24 x Red, 24 x Green, 24 xBlue, 24 x White); 10.528 Lux at 3 m;

16 million colours; linear colour temperature 2800°K – 6500°K

No infrared emission; no ultraviolet emission

LEDs average lifespan: 100.000 hours

Optical group

3 lenses sets available (Spot, Medium flood, Wide flood)

Control

Via any DMX lighting console (FOS 100 POWER SOLO)

Protection

IP65 protection level against the penetration of solids and liquids

Construction

FOS units are made on aluminium and steel

Connections

M16 male connector + cable (length 30 cm) connection system between Power supply

and LED bar (All versions).

POWERCON + XLR 5 poles cable connectors (FOS 100 POWER SOLO IP20);

HARTING 5 poles cable connector (FOS 100 POWER SOLO IP65)

Power supply

Electronic full range power supply AC 90-260V 50 / 60 Hz

Integrated power supply / LED controller (FOS 100 POWER SOLO)

(Z10 POWER IP20 or Z10 POWER IP65);

External dedicated Z40 power supply / LED controller (FOS 100 POWER)

6

Product codes:

03.LB030S.26.FW10 FOS 100 POWER SOLO IP20 FULLWHITE NARROW GREY SILVER

03.LB030S.26.FW25 FOS 100 POWER SOLO IP20 FULLWHITE MEDIUM GREY SILVER

03.LB030S.26.FW40 FOS 100 POWER SOLO IP20 FULLWHITE WIDE GREY SILVER

03.LB030S.FW10 FOS 100 POWER SOLO IP20 FULLWHITE NARROW BLACK

03.LB030S.FW25 FOS 100 POWER SOLO IP20 FULLWHITE MEDIUM BLACK

03.LB030S.FW40 FOS 100 POWER SOLO IP20 FULLWHITE WIDE BLACK

03.LB030S.F10 FOS 100 POWER SOLO IP20 FULLRGBW NARROW BLACK

03.LB030S.F25 FOS 100 POWER SOLO IP20 FULLRGBW MEDIUM BLACK

03.LB030S.F40 FOS 100 POWER SOLO IP20 FULLRGBW WIDE BLACK

03.LB030S.T10 FOS 100 POWER SOLO IP20 RGBW NARROW BLACK

03.LB030S.T25 FOS 100 POWER SOLO IP20 RGBW MEDIUM BLACK

03.LB030S.T40 FOS 100 POWER SOLO IP20 RGBW WIDE BLACK

03.LB031S.26.FW10 FOS 100 POWER SOLO IP65 FULLWHITE NARROW GREY SILVER

03.LB031S.26.FW25 FOS 100 POWER SOLO IP65 FULLWHITE MEDIUM GREY SILVER

03.LB031S.26.FW40 FOS 100 POWER SOLO IP65 FULLWHITE WIDE GREY SILVER

03.LB031S.FW10 FOS 100 POWER SOLO IP65 FULLWHITE NARROW BLACK

03.LB031S.FW25 FOS 100 POWER SOLO IP65 FULLWHITE MEDIUM BLACK

03.LB031S.FW40 FOS 100 POWER SOLO IP65 FULLWHITE WIDE BLACK

03.LB031S.F10 FOS 100 POWER SOLO IP65 FULLRGBW NARROW BLACK

03.LB031S.F25 FOS 100 POWER SOLO IP65 FULLRGBW MEDIUM BLACK

03.LB031S.F40 FOS 100 POWER SOLO IP65 FULLRGBW WIDE BLACK

03.LB031S.T10 FOS 100 POWER SOLO IP65 RGBW NARROW BLACK

03.LB031S.T25 FOS 100 POWER SOLO IP65 RGBW MEDIUM BLACK

03.LB031S.T40 FOS 100 POWER SOLO IP65 RGBW WIDE BLACK

03.LB031.26.FW10 FOS 100 POWER IP65 FULLWHITE NARROW GREY SILVER

03.LB031.26.FW25 FOS 100 POWER IP65 FULLWHITE MEDIUM GREY SILVER

03.LB031.26.FW40 FOS 100 POWER IP65 FULLWHITE WIDE GREY SILVER

03.LB031.FW10 FOS 100 POWER IP65 FULLWHITE NARROW BLACK

03.LB031.FW25 FOS 100 POWER IP65 FULLWHITE MEDIUM BLACK

03.LB031.FW40 FOS 100 POWER IP65 FULLWHITE WIDE BLACK

03.LB031.F10 FOS 100 POWER IP65 FULLRGBW NARROW BLACK

03.LB031.F25 FOS 100 POWER IP65 FULLRGBW MEDIUM BLACK

03.LB031.F40 FOS 100 POWER IP65 FULLRGBW WIDE BLACK

03.LB031.T10 FOS 100 POWER IP65 RGBW NARROW BLACK

03.LB031.T25 FOS 100 POWER IP65 RGBW MEDIUM BLACK

03.LB031.T40 FOS 100 POWER IP65 RGBW WIDE BLACK

5- MAIN ELECTRICAL CHARACTERISTICS (FOS 100 POWER SOLO)

Input Voltage Range : Vin 90 - 260 Vac

Frequency : 50 / 60 Hz

Power Consumption Range : 10 - 200 W

Power Factor (Pf) : 0.95 electronic PFC controller

Efficiency : 90% typical

Control Input:

Control Signal : DMX 512

Dimming System : Constant Current PWM

Address Range : DMX 512 channels addressable by display

7

6- ACCESSORIES

As standard (IP20)

1 x User’s Manual

1 x POWERCON IN male cable connector (FOS 100 POWER SOLO)

(D.T.S. Code: 0520P014)

1 x POWERCON OUT male cable connector (FOS 100 POWER SOLO)

(D.T.S. Code: 0520P029)

1 x XLR 5 poles male cable connector (D.T.S. Code: 0508B028)

1 x XLR 5 poles female cable connector (D.T.S. Code: 0508B027)

1 x Joint/spacer (D.T.S. Code: 00M09519.46 black finish; 00M09519.44 grey finish) with

2 x knobs (D.T.S. Code: 0511P014)

As standard (IP65)

1 x User’s Manual

1 x HARTING 5 poles male cable connector (D.T.S. Code: 02LD0093.1)

1 x Joint/spacer (D.T.S. Code: 00M09519.46 black finish; 00M09519.44 grey finish) with

2 x knobs (D.T.S. Code: 0511P014)

Optional (on request)

Lenses set Spot (FOS 100 POWER FULLCOLOUR) (D.T.S. Code 03.LK.107)

Lenses set Medium flood (FOS 100 POWER FULLCOLOUR) (D.T.S. Code 03.LK.108)

Lenses set Wide flood (FOS 100 POWER FULLCOLOUR) (D.T.S. Code 03.LK.109)

Lenses set Medium flood (FOS 100 POWER RGBW) (D.T.S. Code 03.LK.114)

Lenses set Wide flood (FOS 100 POWER RGBW) (D.T.S. Code 03.LK.115)

G60 ‘’C’’ Clamp (Max. load 50 Kg) *Black (D.T.S. Code 0521A004)

G50 ‘’C’’ Clamp (Max. load 10 Kg) *Black (D.T.S. Code 0521A012)

M16 female (9 poles) cable connector (D.T.S. Code 0508B106)

M16 male (9 poles) cable connector (D.T.S. Code 0508B105)

Z40 Power supply / LED controller (FOS 100 POWER) (D.T.S. Code 03.LA.120)

8

1

6

0

m

140 mm

DIMENSIONS

FOS 100 POWER SOLO

Unit Dimensions Packing Dimensions

(LxWxH) (LxWxH)

990 x 100 x 84,5 mm 1060 x 160 x 200 mm

Weight Weight

7 Kg 8,5 Kg

990 mm

100 mm

8

4

,

5

m

9

FOS 100 POWER

Unit Dimensions Packing Dimensions

(LxWxH) (LxWxH)

990 x 56 x 84,5 mm 1060 x 160 x 200 mm

Weight Weight

5,5 Kg 7 Kg

1

6

0

m

140 mm

990 mm

56 mm

8

4

,

5

m

10

7- IMPORTANT SAFETY INFORMATION

7.1 Fire prevention:

Never locate the fixture on any flammable surface.

Minimum distance from flammable materials: 10 cm.

Minimum distance from the closest illuminable surface: 10 cm.

7.2 Prevention from electric shock:

High voltage is present inside the unit.

Unplug the unit prior to performing any operation which involves touching the inside of

the unit.

This equipment must be grounded, do not connect to non-grounded supplies.

The use of a thermal magnetic circuit breaker is recommended for each FOS 100

POWER SOLO unit.

Use only AC supplies 90-260V, 50 / 60 Hz.

FOS 100 POWER SOLO (IP20) should never be located in position exposed to rain or in

areas of extreme humidity.

A good air ventilation is essential for proper equipment work.

7.3 Safety:

The external surface of the unit may exeed 50°C; never handle the unit until at

least 5 minutes have elapsed since the unit was turned off.

Never install the unit in an enclosed area lacking sufficient air flow.

The ambient temperature should not exeed 40°C and should not be lower than -10°C.

F

!

10cm

11

8- INPUT / OUTPUT CONNECTIONS

FOS 100 POWER SOLO (IP20)

Mains 90-260 V AC

50-60 Hz input Powercon

Female panel connector

DMX IN/OUT

XLR 5 pins Male / Female

Panel Connectors

Mains 90-260 V AC

50-60 Hz output Powercon

Female panel connector

MAX load:

230 V AC

= 10 FOS 100 POWER SOLO

100 V AC = 5 FOS 100 POWER SOLO

M16 LED input

Male cable connector

M16 LED output

Female panel connector

12

FOS 100 POWER (IP65)

M16 LED input

Male cable connector

13

9- DMX SIGNAL CONNECTION (FOS 100 POWER SOLO):

The unit operates using a digital DMX 512 signal.

Connection between the controller and the unit or between units must be carried out

using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the DMX connector chassis.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

unit to the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

If the display showing the DMX address flashes, then one of the following errors has

occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to

use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between

pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the

DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N D A R D

D M X 5 1 2

UNIT 1

UNIT 2

UNIT 3

14

9.1 DMX addresses

FOS 100 POWER SOLO (all models) can be used in seven different modes: 10 DMX

channels mode (default), 6 DMX channels mode (Shutter + Dimmer + RGBW), WALL

mode (6 DMX channels; for use with DTS Wall mounted DMX controller 0514L007),

M4CH mode (5 DMX channels; Dimmer + RGBW), RGBW mode (4 channels), 1 DMX

channel mode or CUSTOM DMX mode (not yet implemented).

If you want to use the FOS 100 POWER SOLO in 10 channels mode, select the 10 CH

mode from the MODE menu and set the following addresses on the mixer:

Projector 1 A001

Projector 2 A011 If you want to select the next projector, just add “10”

Projector 3 A021

….. A….

projector 6 A051

If you want to use the FOS 100 POWER SOLO in “WALL” mode, select the “WALL”

mode from the MODE menu and set the following addresses on the mixer: (To be used

only with DTS Wall mounted DMX controller 0514L007)

Projector 1 A001

Projector 2 A009

Projector 3 A017

….. A….

projector 6 A041

9.2 Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers on

the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing

and the projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more

quickly and you get a faster selection.

If you want to select the next projector, just add “8”.

DTS Wall mounted DMX controller 0514L007 assign

8 DMX channels per unit even if some channels are

not used

15

10- FIRMWARE UPDATING

Warning:

This procedure require a base knowledge of Windows computer applications.

Please refer to an authorised D.T.S. service centre.

To update the software version of the FOS 100 POWER SOLO you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface.

D.T.S. Firmware upgrade utility program.

(The driver and the installation procedure are available in our web site

www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit

software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using D.T.S. Firmware upgrade

utility program.

!

16

11- DISPLAY FUNCTIONS

The FOS 100 POWER SOLO display panel shows all the available functions . Using

these functions, it is possible to change some of the parameters and add some

functions. Changing the D.T.S. setting can vary the functions of the unit so that it does

not respond to the DMX 512 signal used to control it. Carefully follow the instructions

below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

Software version 4.0.7

DOWN

UP

ENTER

MENU

REVERSE DISPLAY

Reverses display's reading depending

on the mounting position (On the

ground or suspended).

DISPLAY STAND BY

To turn off the display (after 5 seconds)

or leave it always on.

Up

-

Down

MENU

ENTER

Up

-

Down

Up-Down

Up-DownENTER

ENTER

Up-Down

ENTER

6 CHANNELS

Up-Down

ENTER

Up-Down

Up-DownENTER

ENTER

Up-Down

ENTER

AUX MODE

Up-Down

ENTER

Show Custom settings

Up-Down

ENTER

Dimmer + RGBA

Up-Down

ENTER

.

ENTER

Up

-

Down

MENU

ENTER

6 CHANNELS

Up

-

Down

Up-Down

ENTER

Default DMX Mode = 10 CH

10 CHANNELS

Up-Down

Floor

Position

Suspension

Position

Display

OFF

Display

Always ON

DMX MODE

To select DMX mode : 10 DMX

channels mode (default), 6 DMX

channels mode (Shutter + Dimmer +

RGB), WALL mode (6 DMX channels;

for use with DTS Wall mounted DMX

controller 0514L007), M3CH mode

(4 DMX channels; Dimmer + RGB),

RGB mode (4 channels), 1 DMX

channel mode.

AUX mode let you activate an

external ON -OFF control on IR

connector.

CUSTOM DMX mode let you set the

parameters for Shutter, Dimmer, Red,

Green, Blue, Ctc, Macro and Function

to the desired DMX channels.

(not yet implemented)

MACRO Function enables

channel mapping macro

rainbow effects

STD (default)

Custom mode enabled

Parameters Setting

on Custom Mode

External ON – OFF

control on IR connector

Standard mode

enabled (Default)

Extended mode enabled:

Rainbow effects on MACRO

channel

M4CH(5 CHANNELS)

RGBA(4 CHANNELS)

1 CHANNEL

17

Boost mode activated

Boost mode deactivated

LED

RGBA Min/Max,

Smooth and

Compression levels

values settings

RGBA MINIMUM VALUES

This menu allow to select

the minimum levels for

Red, Green, Blue and

Amber

RGBA MAXIMUM

VALUES

This menu allow to select

the maximum levels for

These settings have priority

on Master Dimmer

SMOOTH VALUE

This menu allow to select the

value

of the delay ( in milliseconds) for

RGB and Dimmer channels

reaction to DMX or Program

variation.

Off=25 ms delay (Fast response)

20=250 ms delay (Slow response)

COMPRESSION

This menu allow to select

between

Linear courrent output or

Quadratic courrent output

for LEDs

Default = Linear

BOOST DRIVING

This menu allow to increase

the LED’s current from

350mA to 500 mA

Range = Off-20

Default = 4

20 = 250 ms

Smooth response to DMX

variation

Off = 25 ms

Instant response to DMX

variation

Linear=Linear

current output

Quadratic=Linear

light output

With BOOST active, the

LED’s current is set to

500mA

(30%more gain).

Default = Activated

Range =

610 Hz -10 KHz

Default = 610

Default=0

Default=100

Default=0

Default=100

Default=0

Default=100

Up

-

Down

MENU

ENTER

Up

-

Down

Up

-

Down

Up

-

Down

ENTER

Up

-

Down

ENTER

Up

-

Down

Up

-

D

own

ENTER

Up

-

Down

Up

-

Down

ENTER

Up

-

Down

Up

-

Down

ENTER

Up

-

Down

Up

-

Down

ENTER

Up

-

Down

ENTER

Up

-

Down

ENTER

18

AUTOMATIC MODE

Automatic demo game without

DMX controller

ChPr

Chase with 16 steps

previously created in REC

MODE

Speed and Wait time

selectable by user

CUPr

RGB values selectable by

user

Rainbow (rAIn)

Rainbow colours effect.

Speed time selectable by user

CU01-CU16

Color Macros as on DMX

channel 8 (Macro)

WHITE MACROS

16 macros for White color

from 2800 to 6500 ° K

DIMMER

Dimmer level selectable by

user as on DMX channel 2

(Dimmer)

Dimmer level is active for all

the programs and macros

SHUTTER

Shutter level selectable by

user as on DMX channel 1

(Shutter)

Shutter level is active only for

CU01/CU16 and Wh01/Wh16

macros

ESC

Esc from Automatic Mode

Menu

19

u

DMX Recorder Mode

For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit

a further 3 DMX channels are needed.

So that in RECORDER mode ( via DMX) the unit will need 13 channels to be correctly programmed.

The three new DMX channels are:

- DMX channel 11 = SCENES channel

From 0-10 = no function ( r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

- DMX channel 12 = EDIT channel:

From 0-19 = no function

From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to

record the selected scene.

From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as

last scene.

With the channel REC it is possible to record the selected scene as last scene.

- DMX channel 13 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has

been recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only once you

have decided to save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel between 235-

255), in playback mode all 16 scenes will be played through even if not programmed

INFRARED MODE

Infrared remote control.

By activating Ir MODE, it will be possible to navigate

through the unit functions by using the D.T.S. infrared

remote control.

D.T.S. Code :0514L008

ENTER

MENU

Up-Down

ENTER

.

Up-DownENTER

ENTER

Default = OFF

Default = White 1

Default = 255

ENTER

Up-Down

ENTER

MENU

Up-Down

ENTER

.

Up-Down

MENU

Up

-

Down

ENTER

Up-DownENTER

MENU Up-Down

ENTER

REC MODE

In DMX Recorder Mode, it is possible to create

and store the scenes of the ChPr by using an

external DMX controller.

The unit must be setted to 10 channels MODE

NOTE:

External infrared remote

sensor needed.

D.T.S. Code :03.LA.016

Up-DownENTERENTER

MENU

Up-Down

ENTER

SLAVE MODE

Slave mode for ChPr program.

All slave units will be synchronised with master unit,

running their own Chpr program.

FAN SPEED CONTROL

Internal Fan Speed control selectable by

user.

Range: OFF - 24 volt Default : 24 volt

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it will be possible to select

one of the 16 preprogrammed WHITE cues that

will then ran if DMX signal is missing or

not available.

Useful for Emergency EXIT illumination on

public areas.

20

12 - SERVICE MENU

For technical personnel only

To operate this menu:

-Connect the unit to the main

-While reset is running, press the MENU and ENTER keys at the same time.

CHANNELS

This menu allow to set 3 channels or 4 channels LEDs output mode

3 LEDs channels output mode = Not Used on FOS 100 POWER SOLO

4 LEDs channels output mode = Default

PRODUCT MODEL SELECTION:

- FOS 100 POWER = Default

- TITAN PLUS = only for TITAN PLUS unit

- DELTA 8= only for DELTA 8 unit

EXIT

Exit from hidden menu.

AUTOMATIC OPERATION (AUTO):

FOS 100 POWER SOLO can work in automatic mode without a DMX controller. First of

all connect the projectors with a DMX cable (picture below). A maximum quantity of 32

slave units can be connected to the same Master unit.

MASTER SLAVE 1 SLAVE 2 SLAVE 32

To activate Auto mode on the first unit, use the menu to run through the different modes

until AUTO appears on the display, and press enter.

Now it is possible to choose between the different pre-programmed games (CUPr-RAIn-

CU01/CU16-Wh01/Wh16) or ChPr which is user programmable through REC mode. To

confirm game activation press ENTER on the selected GAME.

CUPr-RAIn-CU01/CU16-Wh01/Wh16

The first unit that will work as a Master should be placed in Automatic mode (AUTO), the

other units have to be placed 10 channels DMX mode (MODE 10 CH) and the DMX

address should be set at A001. For RaIn (rainbow) game it is possible to select the

speed for the colour changhing (SPEE).

DIMMER function (in AUTOMATIC MODE) is active for all the programs.

La pagina sta caricando ...

DTS FOS 100 POWER FULL RGBM Manuale utente

Questo manuale è adatto anche per

DTS FOS 100 POWER FULL RGBM Manuale utente

in altre lingue

Documenti correlati

Altri documenti