MyBinding QUANTUM P70IX Manuale utente

GBC Quantum P70iX

Production Grade Punch

Instruction Manual

Quantum™ P70iX

Operator Manual

Manual de

uso

Manuel

d’utilisation

Bedienhandbuch

Bedienhandb

uch

Manuale oper

atore

Handleiding

US/Canada – 230V 50/60 Hz

Assembly Number 7707010

EE.UU./Canadá – 230 V 50/60 Hz

Número de Ensamblaje 7707010

Canada/É.-U. – 230V 50/60 Hz

Numéro d’assemblage 7707010

2 to 26

28 to 51

53 to 76

USA/Kanada – 230V 50/60 Hz

Baugruppennr. 7707010

US/Canada – 230V 50/60 Hz

Gruppo numero 7707010

VS/Canada – 230V 50/60 Hz

Assemblagenummer 7707010

78 to 101

103 to 126

128 to 151

Table of Contents

Section Page

Safety Information

Safety Messages 3

Important Safeguards 4

Service 5

Cleaning 5

Main Cordset Selection 6

FCC Rules, Electrical Interference 7

Service and Equipment Maintenance Agreement 7

1. Introduction

Introduction 8

Unpacking and Setup 8

2. Getting to Know your Quantum P70iX

Paper Static 9

Limitations 10

Plastic Cover Stock 11

3. Operation

Operating Controls 12

4. Options and Accessories

Die Set 13

Die Set Storage 14

5. Graphical User Interface

Home Screen Introduction 15

Home Screen Commands 16

Speed Command 17

Select Saved Job 18

Create a New Job, Punch Edge 19

Create a New Job, Side Edge 20

Create a New Job, Punch Die 21

Create a New Job, Change Die 22

Screen Information, Job Running 23

Screen Information, Stop Command 24

6. Maintenance

Slug Bin (Chad Container) 25

Punch Pins 25

Service 25

Troubleshooting 25

7. Specifications

Specifications Quantum P70iX 26

2

Safety Information

SAFETY MESSAGES

The safety of you and others is very important to GBC. Important safety mes-

sages and information are contained within this manual as well as on the

machine itself. Please be certain to carefully read and understand all of these

before operating the machine.

!

The safety alert symbol precedes each safety message in this Operating

Instruction Manual. This symbol indicates a potential personal safety

hazard that could hurt you or others, as well as cause product or property

damage.

The following pictorial is found on the

Quantum P70iX:

!

CAUTION:

This means you could fall and be injured if you try to stand or

sit on the conveyor belts.

!

WARNING:

This means you can be seriously injured by crushing and

cutting, moving parts. Do not operate without guards in place. Do

not

attempt to defeat any of the safety interlock switches.

!

WARNING:

This means you can be seriously injured by the covers falling

on you. Keep your hands and other body parts away to avoid getting them

crushed or cut.

3

Safety Information

SAFETY MESSAGES continued

!

WARNING: This means you can be seriously injured by crushing

and cutting, moving parts. Do not operate without guards in place.

Do not attempt to defeat any of the safety interlock switches.

The following symbols appear on this product, and their meaning is as follows:

I

Means the electrical power is “ON”.

O

Means the electrical power is “OFF”.

IMPORTANT SAFEGUARDS

• Use the Quantum P70iX only for its intended purpose of punching paper and

covers according to the indicated specifications.

• Retain this Operating Instructions manual for later use.

!

CAUTION: IN CASE OF EMERGENCY, USE THE POWER CORD AS A

MAIN DISCONNECT.

4

Safety Information

IMPORTANT SAFEGUARDS continued

• The

Quantum P70iX

must be connected to a supply voltage corresponding

to the electrical rating of the machine operating instructions (also listed on

the serial number label).

• The socket-outlet shall be located near the equipment and shall be easily

accessible.

• The grounding plug is a safety feature and will only fit into the proper ground-

ing-type power outlet. If you are unable to insert the plug into an outlet, con-

tact a qualified electrician to have a suitable outlet installed. Do not alter the

plug on the end of the cordset (if provided) of the Quantum P70iX. It was

provided for your safety.

• Unplug the Quantum P70iX before moving the machine or whenever the

machine is not in use for an extended period of time.

• Do not operate the Quantum P70iX if the machine has a damaged power

supply cord or plug. Do not operate the machine after any malfunction, if liq-

uid has been spilled into the machine, or it the machine has been damaged

in any way.

• Do not overload electrical outlets beyond their capacity. To do so can result in

fire or electrical shock.

• Do not attempt to bypass the safety interlocks, if you do so you may be

injured

SERVICE

Do not attempt to service your Quantum P70iX yourself. Contact an authorized

GBC service representative for any required repairs or major maintenance for

your Quantum P70iX.

There are NO user-serviceable parts inside the machine. To avoid potential per-

sonal injury and/or property or machine damage.

!

DO NOT REMOVE THE MACHINE’S SIDE COVERS AND TOP

COVERS.

CLEANING

You may clean the exterior of the Quantum P70iX using a soft, damp cloth. Do

not use detergent or solvents as damage to the machine may occur.

5

Safety Information

MAIN CORDSET SELECTION

(THE FOLLOWING NOTE APPLIES ONLY TO EUROPEAN UNITS)

!

CAUTION: WHEN CHOOSING A DETACHABLE LINE CORD FOR USE

WITH YOUR Quantum P70iX, ALWAYS OBSERVE THE FOLLOWING

PRECAUTIONS

The cordset consist of three parts; the attachment plug, cordage and appliance

inlet. Each of these components must have European regulatory approvals for

safety.

The following minimum electrical ratings for the specific cordset are published

for safety purposes. DO NOT USE CORDSETS THAT DO NOT MEET THE

FOLLOWING MINIMUM ELECTRICAL REQUIREMENTS.

PLUG:

3 amperes, 250 volts, 50/60 Hz, Class 1, 3 conductor, European safety

approved.

CORDAGE:

Type H05VV-F3G0.75, Harmonized ( < HAR> ). The “< >” sym-

bols indicate cordage approved to appropriate European standard (NOTE:

“HAR” may be substituted for approval mark of European safety agency, which

approved the cordage. An example would be “ < VDE > “).

APPLIANCE CONNECTOR:

3 ampere, 250 volts, 50/60 Hz, European safety

approved, Type IEC 320. The cordset shall not exceed 3 meters in length.

A

cordset with component electrical ratings greater than the minimum

specified

electrical ratings may be substituted.

6

Safety Information

FCC RULES, ELECTRICAL INTERFERENCE

(THE FOLLOWING NOTE APPLIES ONLY TO THE U.S. UNITS.)

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the Operator Manual, may cause

harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his/her own expense.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY

!

APPROVED BY GENERAL BINDING CORPORATION COULD VOID

YOUR AUTHORITY TO OPERATE THE EQUIPMENT.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numerique dela classe A est conforme a la norme NMB-003 du

Canada.

SERVICE AND EQUIPMENT MAINTENANCE AGREEMENT

By purchasing the P70iX you have invested in a highly capable punching

machine that will give you years of reliable service. To help protect this invest-

ment be certain to take advantage of the GBC Equipment Maintenance

Agreement (EMA). The EMA provides your P70iX with proper ongoing mainte-

nance and care, helping to ensure the years of quality performance and long life

built into the machine. Without an EMA, a charge for parts and labor would

result from every normal maintenance or repair service call. An EMA for your

P70iX eliminates this possibility by providing you with a low, fixed annual cost for

protecting your valuable machine investment. For full details about purchasing

an EMA, consult with your GBC Sales Representative or contact:

General Binding Corporation

500 Bond Street

Lincolnshire, IL 60069

Or Call: 1-800-790-7787

A GBC Authorized Technician must perform all service and maintenance unless it

is operator maintenance in accordance with the P70iX Automatic Punch

User

Guide. Use of the P70iX Automatic Punch in any manner not in accordance

with

the GBC P70iX User Guide is not recommended and may void your warranty

or

maintenance contract

Trained operators and regular operator maintenance of the P70iX A can opti-

mize performance and minimize service calls.

7

1. Introduction

INTRODUCTION

The Quantum P70iX is designed to meet the unique requirements of the digital

print marketplace. It is designed to support all commonly required punching pat-

terns, including three-hole, comb, VeloBind, Twin-Loop wire, and Color Coil.

Custom die patterns are also available. This new system is designed to deliver

the quick changeover requirements of the short-run digital printer.

Virtually all set-ups are quickly and easily accomplished from the digital print

display panel, overcoming a major time-consuming aspect of traditional produc-

tion punches. Die changes can be accomplished in a short time without tools.

The system is pre-programmed with all common paper sizes, and can store 20

custom jobs.

The P70iX is designed to handle a wide range of media. It can handle sheet

sizes from 5 1/2” x 5 1/2” to 9” x 12”, including mixed paper-weights and cover

stocks. Another key feature is the system’s ability to process intermixed index

tabs without any special adjustments.

The P70iX incorporates GBC’s new “stack processing” technology, which is

designed to reduce operator labor cost. This new architecture allows the system

to process a 14” stack (3,500 sheets 20# bond) without operator attendance.

The P70iX offers a maximum throughput speed of 60,000 sheets per hour.

The Quantum P70iX is GBC’s revolutionary new, near-line, high-speed Digital

Production Punch. It sets up in minutes and keeps up, side-by-side, with banks

of today’s fastest digital print engines.

These instructions have been prepared to acquaint you with the Quantum P70iX

punch and it’s operation. Please read them carefully. Keep these operating

instructions for future reference.

UNPACKING AND SETUP

The Quantum P70iX punch must be installed by a qualified GBC Technician.

Your Technician will ensure that the system is properly leveled and ready to run.

8

2. Getting to Know your Quantum P70iX

PAPER STATIC

External factors can affect performance of your P70iX. These factors include

customer requirements for hole quality, throughput materials (paper/transparen-

cies/covers), toner coverage on the printed page, and environmental factors.

Static in the paper can result in poor performance. If your P70iX runs a fresh

ream of clean white paper but has trouble with your printed job, it may be due to

static. The following tips might help you to correct this problem.

Suggestions for static: If you’re P70iX Automatic Punch is having trouble

running certain jobs, it may be due to excessive static build-up in the

paper. Here are some suggestions that may help to minimize the static

effect.

1. Fan the paper before loading it into the P70iX. Do not jog the paper; this

will only cause more static build-up.

2. Slow the speed down on the P70iX. This will give the paper more time to

settle down into the die.

3. Consider the purchase of a room humidifier to add moisture into the air.

Dry air helps to produce more static.

4. Move your punching operation to an environmentally controlled room.

5. Pay close attention to seasonal conditions. Procedures you follow in the

hot humid days may need to be modified during dry winter months when

static is most common.

6. Consider storing your unwrapped paper jobs in very large Tupperware

type containers to retain the moisture. Using these containers along with

humidor type products can actually reintroduce moisture into the paper

that was lost during the fusing process.

7. Contact your copier/printer service department and enquire as to the

possibility of lowering your fuser temperature.

9

2. Getting to Know your Quantum P70iX

LIMITATIONS

To ensure your satisfaction, please take a moment to understand the following

application limitations.

• Tabs must have a 1/4” shoulder. Without this shoulder, the paper lift cannot

be properly tapped into the punch die, resulting in poor hole registration.

• When running mixed stocks, you must ensure the dimensions are consistent.

One stock smaller than the other will prevent proper hole registration.

• Very slippery paper or cover stocks may not run in the P70iX. Test small stacks

at slower speeds and/or smaller lift sizes before committing to a large job.

• Cover stocks mixed with paper usually run best at slower speeds.

• If a very straight output stack is important for a particular job, select speed

one or two for improved stack quality.

• When running cover stock alone, performance is best at slower speeds.

• Improper loading of stack will result in feeding problems. Take care to justify

the stack against the input door and the right stacking registration bracket.

• Some specialty papers (NCR paper for example) will show handling marks.

• The punched edge of a stack will be taller than when it went in. With some

papers, paper sizes and die set combinations; you may want to reduce the

input stack to prevent slumping, instability or excessive height.

• Excessive paper curl can result in poor feeding or jams. You can identify

excessive paper curl when you see more than 1/4" of curl 2" from the paper

edge. If curl is not excessive, you will have best results with the curl down.

For our purposes, curl down is defined as the outside front edges are down

and the middle is up.

10

2. Getting to Know your Quantum P70iX

PLASTIC COVER STOCK

The Quantum P70iX is capable of handling and punching some types of clear

cover stock materials. In fact, every Quantum P70iX is tested with clear covers

before it leaves the factory. The following guidelines will help you to understand

the capabilities of the Quantum P70iX system. In cases where your particular

clear cover stock is not suitable to run through the Quantum P70iX, you may

w

ant to try separating the clear covers from the book contents and punching the

clear covers using a GBC Magnapunch heavy duty table top punch.

• For clear cover stocks to work in the GBC Quantum P70iX, they require the

body found in GBC Premium covers, which are 10-mil and 14-mil thickness.

• Clear covers must be run intermixed. The photo sensors used on the

Quantum cannot detect clear covers.

• When running mixed stocks, you must ensure the dimensions are consistent.

One stock smaller than the other will prevent proper hole-registration.

• With a smaller lift size the punch is more likely to pick a single clear cover.

Lift size settings 5-7 work best.

• It is best to run a job containing clear cover stocks at a slower speed. GBC

recommends 75 LPM for most jobs.

• Clear covers produce more static sticking than other stock, ambient condi-

tions will affect performance.

• If a clear cover is picked alone, the punch may shut down with a false jam.

This is due to the inability of the optical sensors to see some clear cover

stocks. In this event, the stock will not be damaged. Simply press the green

button to continue.

11

3. Operation

OPERATION CONTROLS

2

3

1

1. Ergonomic

Workflow:

load, unload and pro-

gram from the same

side without any w

asted

steps.

Loading and unloading

stack can be safely

accomplished while the

machine is punching.

2. Die Set Changes:

are completed without

tools and only take sec-

onds to perform.

3. Fully Digital:

push button set-up

and

operation. With

simple

steps to recall up to

24

custom jobs.

12

4. Options and Accessories

DIE SETS

The GBC Quantum P70iX Automatic Punch is capable of punching a variety of hole

patterns commonly used in binding today, by simply changing the Die Set. Die sets

can be changed in seconds without tools.

A significant feature of the Quantum P70iX is that it uses GBC Magnapunch Die Sets.

If you include a Magnapunch in your paper punch work station, you will enjoy the

flexability and versility of diesets that can be used in either punch platform. Some jobs

or parts of jobs may be better suited for the table top paper punch.

Please note: The PB Plastic Bind with multiple adjust depth of punch Magnapunch Die

Set is not suitable for use in the automatic paper handling system utilized by the

Quantum.

The Die Sets currently available are listed below. Your GBC Sales Representative can

provide you with price and availability, or contact the GBC Call Center at 1-800-723-

4000. For more information, visit GBC’s website at www.gbcconnect.com.

Each punching style listed below requires a separate die set for the Quantum P70iX.

Quantum P70iX Automatic Punch - Die Sets Product Code

PB Plastic Bind – Deepest Fixed Back Gauge, .187” 7707230

PB Plastic Bind – Middle Fixed Back Gauge, .141” 7707220

PB Plastic Bind – Shallow Fixed Back Gauge, .094” 7707210

W3 Twin Loop Wire - 3:1 Round 7708350

W3 Twin Loop Wire - 3:1 Square 7708360

W2 Twin Loop Wire - 2:1 Rectangular 7708330

W2 Twin Loop Wire - 2:1 Round 7708320

C4 Color Coil – 4:1 Oval .2475 7707290

C4 Color Coil – 4:1 Round .2475 Pitch 7708300

C4 Color Coil - 4:1 Round .250 Pitch 7708310

Color Coil Heavy Duty C4 Oval Quantum Dieset 7707300

VB VeloBind 11 inch 7708340

Ring Binder 2-4 Standard 5/16” Diameter Hole (Europe) 7708390

Ring Binder 3-5-7 5/16” Diameter Hole (U.S.) 7708380

GBC offers a full suite of binding equipment and supplies to meet your binding needs.

In addition Custom Die Sets are available for the Quantum P70iX. For additional

information, consult with your GBC Sales Representative.

IMPORTANT: A decal on the handle of each interchangeable die set indicates the

punching pattern.

13

4. Options and Accessories

DIE SET STORAGE

GBC Die Set Storage Cabinet

#7703207

is an excellent way to store all of your

interchangeable die sets for the Quantum P70iX (see figure 3). This special

product securely holds three die sets, protecting them from dirt, dust, and acci-

dental damage. Contact your sales representative for information on obtaining a

Die Set Storage Cabinet.

Figure 3

!

CAUTION: POSSIBLE PINCH POINT HAZARD. WHEN INSTALLING

DIE SETS INTO YOUR Quantum P70iX, ALWAYS KEEP FINGERS AND

BODY PARTS OUT OF THE MACHINE’S DIE SET SLOT AND AWAY

FROM ALL AREAS OF THE DIE SET EXCEPT FOR THE FINGER

GROOVE IN THE DIE SET’S HANDLE. FAILURE TO OBSERVE THESE

PRECAUTIONS MAY RESULT IN INJURY.

14

5. Graphical User Interface

HOME SCREEN INTRODUCTION

GBC QUANTUM PUNCH

90 LPM

7

MODE

PROOF

UNLOAD

JOB MANAGER

LANGUAGE

1 2 3

4 5 6

7 8 9

0 OK

The Home Screen is the starting point for operation of the Quantum P70iX. At

this screen, you are able to see the job that the Quantum is ready to run. In the

example above, the Quantum is setup to run the following job:

• A paper size of 8.5” x 11” with punching on the 11” side.

• A lift thickness of “7” which is approximately 7 sheets of 24 pound paper.

• The speed is set at 90 LPM (lifts per minute).

• Punching holes using a PB (Plastic Bind) die with a back gauge of .141”.

• The Quantum is also operating with the controls in English.

If these job settings are acceptable, you may start your job by simply:

• Loading your paper on the input belts.

• Pressing the green start button ( ).

15

5. Graphical User Interface

HOME SCREEN COMMANDS

GBC QUANTUM PUNCH

90 LPM

7

MODE

PROOF

UNLOAD

JOB MANAGER

LANGUAGE

1 2 3

4 5 6

7 8 9

0 OK

MODE:

allows you to select between Automatic or Manual. Automatic Mode

means the Quantum will continue to run non-stop as long as you place paper on

the Input Belts and remove the punched stack of paper from the Output Belts.

The Manual Mode means the Quantum will stop before it takes the next paper

stack in for processing. This mode is helpful if you want to start a new job that

requires different settings such as a different Die Set, or a different paper size.

PROOF: you can run a few lifts of your job and have the Quantum stop. This

feature enables you to check the hole positioning and pattern to ensure the setup

is the job you intended.

UNLOAD: means that when pressed, the job currently inside of the Quantum

will

exit. This is helpful if you need to start a job over again for some reason.

JOB MANAGER: will take you to the Job Manager screen where a different job

can be selected or created.

LANGUAGE: you may select between English, Spanish, French and German.

16

5. Graphical User Interface

SPEED COMMAND (LPM)

GBC QUANTUM PUNCH

90 LPM

7

MODE

PROOF

UNLOAD

JOB MANAGER

LANGUAGE

1 2 3

4 5 6

7 8 9

0 OK

You have constant control of the Speed by controlling the LPM or Lifts Per

Minute and the size of each Lift by adjusting the number of sheets per Lift.

Lifts Per Minute (LPM) is controlled by pressing the Left – Right arrow buttons

above the numeric key pad. You will see the number change in the window. The

example above reads “90 LPM”. The choices are 60, 75, 90 and 105 LPM.

NOTE:

You would choose a lower speed for harder to handle media such as

jobs with heavier than normal curl or heavier than normal toner coverage.

Lift command (sheets punched per stroke).

The size of the lift is controlled by pressing the Up – Down arrows above the

numeric key pad. The numbers roughly equal the number of sheets of 24 pound

bond paper that would be picked at this setting. This feature does not actually

count sheets however and you should not expect the lift to be exactly this quan-

tity. The example shown is of a lift size of “7”

NOTE:

You would choose a lower lift for harder to handle media such as jobs

with heavier than normal curl or heavier than normal toner coverage.

17

5. Graphical User Interface

SELECT A SAVED JOB

JOB MANAGER — USE ARROWS

GO JOB 1

VIEW 13-24

EDITOR HOME

1 2 3

4 5 6

7 8 9

0 OK

At the Job Manager Screen you are able to scroll between saved jobs (1 – 12) by

simply pressing the right-left and/or the up/down buttons. In the example above,

JOB 1 has been highlighted. To select this job and continue, simply press

“GO JOB 1”

button.

Other Job Manager Features:

• VIEW

13-24: press to select a job #13 to #24.

• HOME:

press to return directly to the Home screen.

• EDIT:

a current job or create a new job,

Scroll to the job you wish to Edit, or,

Scroll to an unused job. In the example above, Job 12 is unused.

Press the EDITOR button.

18

5. Graphical User Interface

CREATE A NEW JOB: Select a punch edge

EDITOR

0 . . 9

USE ARROWS T

O

CHANGE

OTHER

SIZES

ACCEPT

ESCAPE

SAVE

GO TO NEXT

SETTING

NO CHANGE

GO BACK

DATA OK

STORE

1

1 2 3

ESCAPE SAVE

ACCEPT

4 5 6

7 8 9

0 OK

To Edit an exiting job or create a new job, press the up – down arrows to select

the desired setting. In the example above, the Punch Edge paper dimension has

been selected and currently reads 11”.

Alternatively, the dimension can be entered directly using the numeric ke

ypad.

The machine will automatically toggle between inches and millimeters depend

-

ing on the size of the number entered.

The min-max range for the punch edge is 5.50” to 12.00” (139.7 mm to

304.8

mm). If at this time you entered 140 and 305, the system would

automatically

recognize the dimensions as 140 millimeters (mm).

Once the desired punch edge dimension appears on the display, press the

“ACCEPT”

button.

19

La pagina sta caricando ...

MyBinding QUANTUM P70IX Manuale utente

Questo manuale è adatto anche per

MyBinding QUANTUM P70IX Manuale utente

in altre lingue

Documenti correlati

Altri documenti