CET LFM40AN Manuale del proprietario

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 1

CET

VISUALIZED FREQUENCIMETER

WITH ANALOG OUTPUT

Type:

LFM40AN

PROGRAMMABLE DIGITAL VISUALIZATOR OF

ROTATIONS WITH 4 DIGITS, INPUT SUITABLE FOR

MONO DIRCTIONAL COUNTING AND ANALOG

OUTPUT

The period counter model LFM40AN is a

frequencymeter that calculate and displays continually

the impulses frequency of the input and give to the

output a direct current referred to the frequency showed.

For its characteristics and versatility this instrument can

be used as tools counter, speed survey and where is

necessary to control linear speed or rotation speed of

motor trees with an external system.

GENERAL CHARACTERISTICS

PROGRAMMABLE PARAMETERS

• Frontal keyboard in polycarbonate (antiscratch, antioil,

antacid).

• IP65 protection degree

• Accessible parameters with key software

• Removable terminals connection.

• Execution DIN 48 x 96.

• Recessed assembly.

• Special retaining brackets.

• Multiplier Factor

• Divisor Factor

• Time Base

• Display Reset Time

• Display Adjournment Time

• Analog Output Adjournment Time

• Input for Electromechanical or Logic Contacts

• Reset Key

• Decimal Point

• Initial Scale of the Analog Output

• Full Scale of the Analog Output

TECHNICAL CHARACTERISTICS

• POWER SUPPLY IN ALTERNATE CURRENT

• POWER SUPPLY IN DIRECT CURRENT

• POWER SUPPLY TOLERANCE

• ABSORPTION

• OPERATING TEMPERATURE

• CLIMATIC CONDITIONS

• COUNTER AND TOTALIZER VISUALIZATION

• MULTIPLICATION FACTOR OF THE INPULSES IN INPUT

• DIVISOR FACTOR OF THE INPULSES IN INPUT

• TIME BASE

• INPUT TYPE

• MAXIMUM COUNT FREQUENCY

• MINIMUM TIME FOR INPULSES COUNT

• CUT OFF FREQUENCY FOR ELECTROMECHANICAL

INPUTS

• ANALOG OUTPUT

• RESOLUTION OF THE ANALOG OUTPUT

• MAXIMUM LOAD RESISTENCE

• AUXILIARY INPUT SUPPLY

•

PROGRAMMED DATA MEMORY

: single power 24 - 110 - 230 Vac (50 / 60 Hz).

: single power 24 Vdc

: +10% - 15%.

: 2 W - 3 VA.

: -5 °C + 55 °C.

: U.R. 95 % a 40 °C (without condensate).

: 4 digits, display high 14mm.

: programmable from 1 to 10000.

: Programmable between 1 / 60 / 3600.

: suitable for electromechanical contacts, amplified proximity

and encoder, NPN and PNP

: up to 25 KHz with Duty Cycle=50%.

: 0,25 mSec.

: about 30 Hz.

:

: 0 – 20mA or 4 – 20mA or 10VDC

: 16 bit analog conversion (65536 levels)

: lower than 600 Ohm

: 24 Vdc - 80 mA available on terminals.

: Static (no battery)

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 2

FRONTAL KEYBOARD DESCRIPTION

ø

YELLOW

The key 'LEFT ARROW' in normal operating phase visualizes, blinking, all the programming executed without the

limitation of the insertion code. The time of scansion of the programming is given from the pressure of the same key.

It exits automatically from this phase after 5 sec of the last pressure of the same key.

In programming phase it moves the cursor of the figure towards left of a step, than at the beginning it is on the right

side first one on the. At the end it resumes from the first one to right.

ù

YELLOW

The key 'UP ARROW' in normal operating phase visualizes the totalizer of impulses.

In programming phase it increases the value of the blinking figure.

ú

BLUE

The key 'PRG' pressed for 2 sec. allows to enter in the programming phase, visualizing on display

C.0000.

In the programming phase, pressing key 'PRG' impulsively, it exits from the programming phase. The

instrument exits automatically from the programming phase, 60 sec. after the pressure of the last key.

û

RED

The key 'ENT/RES' in normal phase of counting has the 'RESET' function, with the modalities to it

attributed in the programming phase.

In programming phase it confirms and memorizes the visualized data and passes to the successive

function. If it has arrived to list end it resumes from the beginning.

INPUTS / OUTPUTS DESCRIPTION

DC POWER

(input 1-2) 24V DC Power Supply of the instrument.

AC POWER

(input 3-4) AC Power Supply of the instrument; it can be to 24 - 110 - 230 VAC according to demand.

12 (24) VDC - 80mA

(input 5 - 6) 12 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and amplified

proximity.

INPUT

(input 7) Input of count adapted for electromechanical and logical contacts, encoder and 3 wires proximity

amplified, configurable in Positive (PNP) and Negative (NPN) logic by the dip switches on the rear.

DISPLAY DESCRIPTION

----

When the device is switched on and when there are no impulses in its input, the device

visualize 4 horizontal bars.

Pressing the key ù the totalizer of impulses will be visualized for 5 sec.

Toì

9999

The totalizer visualizes all the impulses that the instrument counts from its input IN1.

It can be resetted through frontal key RES only or from RESET input when it is visualized on

the display

.

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 3

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key PRG for about 2 sec. On the display appears:

Cod

000

GROUP 1

:

in order to approach the parameters of group 1, insert code

101

and press

ENT

¾Æ

0001

F.M. = 4 digits multiplier, programmable from 1 to 10000. This parameter allows to multiply

the number of the input impulses, showing them on the display in an other format. If it

programmed = 0 it means programmed 10000.

Attention: the variation of the value of the multiplying modifies automatically the value of the

count and the totalizer.

¾¼

0001

F.d. = 4 digits divisor, programmable from 1 to 10000. This parameter allows to divide the

number of the input impulses, showing them on the display in an other format. If it programmed

= 0 it means programmed 10000.

Attention: the variation of the value of the multiplying modifies automatically the value of the

count and the totalizer.

ºÌ

60

b.t. = Time Base.

This programming allows to select in which time base shows on the display the measure in

input. There are three scales:

1 = Time Base: seconds, measure visualization in seconds (ex. Meters/seconds)

60 = Time Base: minutes, measure visualization in minutes (ex. Liters/minutes)

3600 = Time Base: hours, measure visualization in hours (ex. Bottles/hour)

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 4

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.

In order to approach the programming, proceed in the following way:

- Press key

PRG

for about 2 sec. On the display appears:

Cod

000

GROUP 2

:

in order to approach the parameters of GROUP 3, insert code

020

and press

ENT

Ìê

01

t.r. = Reset time of the display.

This parameter allows to program the maximum time from the last impulse after that the

instrument reset the display, showing the four horizontal bars. If programmed = 0, with no

impulses in input the instrument shows the last calculated value. If the programmed time is

lower than the time between the impulses, the instrument shows the four horizontal bars.

This parameter is useful to indicate when a plant is in stop or when there are no

impulses in input or when the impulses source is damaged. It’s programmable

between 1 (instantaneous) and 99 seconds.

Ìç Ç1

Updating time of the analog output.

This parameter allows to program the delay time of the data adjournment on the

analog output. It’s programmable between 0 (instantaneous) and 9,9 sec

¼¼ O1

d.d. = Updating time of the display.

This parameter allows to program the delay time of the data adjournment on the

display. It’s programmable between 0 (instantaneous) and 99 sec

1æ F

1æ

5

Input Fast - Slow.

This programming allows to set the count input to read signals coming from electromechanical

contacts (relays, switches etc.) or from logical signals like proximity switches transistor and

encoder.

In = F. sets the input to read digital signals up to 28 KHz.

In = S. sets the input to read electromechanical signals up to 25 Hz.

rËon

Operation of the RESET Key; this programming enable and disable the RESET working of

the frontal RES key during the operation, as in the following modes:

RS.on. = executes the RESET of the visualized parameter

RS.oF. = RESET working of the RES key excluded.

R ÁË

0001

I.S. = Initial Scale of the Analog Output

This programming selects the value corresponding to the Initial Scale of the Analog

Output. It’s programmable between 0 and 9999.

R¾Ë

9999

F.S. = Full Scale of the Analog Output

This programming selects the value corresponding to the Full Scale of the Analog

Output. It’s programmable between 0 and 10000. If it set to 00000 the value is

10000.

¼È O

¼È 4

d.P. = Programming of the Decimal Point

This programming allows to add a decimal point to the visualization on the 4 digits, in order to

obtain counts with various resolutions.

d.p. = 0 Decimal Point excluded; visualization 9999

d.p. = 1 Decimal Point on the second display from right; visualization 999,9

d.p. = 2 Decimal Point on the third party display from right; visualization 99,99

d.p. = 3 Decimal Point on the fourth display from right; visualization 9,999

d.p. = 4 Floating Point.

¹È È

¹È ê

A.P. = Activation mode of the programmed parameters.

With this programming is possible to activate the executed programming directly to the exit of

the programming or, when exited of the programming, after a RESET (with frontal key or from

rear input).

A.P. = P. Activation of the parameters to the exit of the programming.

A.P. = r. Activation of the parameters to the exit of the programming after a RESET.

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 5

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 6

Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 7

DECLARATION OF ‘CE’ CONFORMITY

CE NORMATIVE CONFORMITY

Borgolavezzaro, October , 03rd 2005

The building firm:

CET s.r.l

Head office:

Strada Statale 211, Km 53,550

28071 Borgolavezzaro (No) ITALIA

Tel. 0039 - 0321 - 885301 Fax. 0039 - 0321 - 885560

declare that the products:

type :

Visualized Digital Period Counter

model:

LFM40AN

use class:

Industrial

are in conformity with the following normative:

EN55011

ENV50141

ENV50204

EN61000-4-2

EN61000-4-4

The constructor :

CET s.r.l.

________________________________

Signature

CET s.r.l.

Vers. 1.0

LFM 40AN

Pag. 8

CONNECTIONS

INPUT SIGNALS

TTL LOGIC TTL LOGIC

NPN PNP

NPN PROGRAMMING PNP PROGRAMMING

AMPLIFIED PROXIMITY AND

ENCODER – 24 Vdc

NPN PNP

CONTACT CONTACT

OVERALL DIMENSIONS (mm)

FRONT SIDE

REAR DRILL TEMPLATE

CET

CETCET

CET

CETCET

CET

s.r.l.

Strada Statale 211 Km 53,550

28071 Borgolavezzaro - NO - ITALY

Tel : ++39 0321-885180/885301/885807

Fax : ++39 0321-885560

info@cet-italy.com

www.cet-italy.com

Agent :

48

96

ENT

RES

PROG

L1

L2

6325

Electronic counter

LFM

CET

139

115

9

15

44x92

REMOVABLE

TERMINALS

RETAINING

BRACKETS

10

MAX

93

45

7

6

7

5

6

7

5

7

PROX

ENCOD

5

7

6

PROX

ENCOD

5

7

6

92

44

1 2 3 4 5 6 7

-

+

24 VDC AC

POWER POWER

+

-

24 Vdc

80mA

1

2

3

4

5

6

7

INPUT

1

2

3

ANALOG

OUTPUT

GND

CET LFM40AN Manuale del proprietario

CET LFM40AN Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti