Denon D-M37 Manuale del proprietario

Marca: Denon

Modello: D-M37

Categoria: Lettore CD

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

RCD-M37

CD RECEIVER

RCD-M37

Owner’s Manual

Manuel de l’Utilisateur

Manual del usuario

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.



$-"44

-"4&3

130%6$5





Copyrights / Droits d’auteur / Derechos de Autor

• It is prohibited by law to reproduce, broadcast, rent or play discs in

public without the consent of the copyright holder.

• La reproduction, la diffusion, la location, le prêt ou la lecture

publique de ces disques sont interdits sans le consentement du

détenteur des droits d’auteur.

• De acuerdo con las leyes está prohibido reproducir, emitir, alquilar

o interpretar discos en público sin la autorización del propietario de

los derechos de autor.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY

ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.

Laser Class (IEC 60825-1:2001)

IMPOTANT SAFETY

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug does not ﬁt into

your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

speciﬁed by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

15. Batteries shall not be exposed to excessive heat such as sunshine, ﬁre or

the like.

CAUTION:

• The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, tablecloths, curtains,

etc.

• No naked ﬂame sources, such as lighted candles, should be

placed on the unit.

• Observe and follow local regulations regarding battery disposal.

• Do not expose the unit to dripping or splashing ﬂuids.

• Do not place objects ﬁlled with liquids, such as vases, on the

unit.

ATTENTION:

• La ventilation ne doit pas être gênée en recouvrant les ouvertures

de la ventilation avec des objets tels que journaux, rideaux, tissus,

etc.

• Aucune ﬂamme nue, par exemple une bougie, ne doit être placée

sur l’appareil.

• Veillez à respecter les lois en vigueur lorsque vous jetez les piles

usagées.

• L’appareil ne doit pas être exposé à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant du liquide, par exemple un vase,

sur l’appareil.

PRECAUCIÓN:

• La ventilación no debe quedar obstruida por haberse cubierto las

aperturas con objetos como periódicos, manteles, cortinas, etc.

• No debe colocarse sobre el aparato ninguna fuente inﬂamable sin

protección, como velas encendidas.

• A la hora de deshacerse de las pilas, respete la normativa para el

cuidado del medio ambiente.

• No exponer el aparato al goteo o salpicaduras cuando se utilice.

• No colocar sobre el aparato objetos llenos de líquido, como

jarros.

CAUTION:

To completely disconnect this product from the mains, disconnect

the plug from the wall socket outlet.

The mains plug is used to completely interrupt the power supply to

the unit and must be within easy access by the user.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur,

débranchez la prise de la prise murale.

La prise secteur est utilisée pour couper complètement

l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder

facilement.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación

eléctrica, desconecte el enchufe del enchufe de la pared.

El enchufe de la alimentación eléctrica se utiliza para interrumpir por

completo el suministro de alimentación eléctrica a la unidad y debe

de encontrarse en un lugar al que el usuario tenga fácil acceso.

ESPAÑOLENGLISH FRANCAIS

ENGLISHFRANCAISESPAÑOL

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC Information (For US customers)

1. PRODUCT

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

product may not cause harmful interference, and (2) this product must accept any interference received, including

interference that may cause undesired operation.

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modiﬁcation not expressly approved by DENON may void your authority, granted by the FCC, to use the product.

3. NOTE

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this product does cause harmful interference to radio or

television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the product into an outlet on a circuit different from that to which the receiver is connected.

• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for

help.

III

• Avoid high temperatures.

Allow for sufﬁcient heat dispersion when

installed in a rack.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur

sufﬁsante lors de l’installation sur une

étagère.

• Evite altas temperaturas.

Permite la suﬁciente dispersión del calor

cuando está instalado en la consola.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el

cordón de energía.

• Keep the unit free from moisture, water,

and dust.

• Protéger l’appareil contre l’humidité, l’eau

et la poussière.

• Mantenga el equipo libre de humedad,

agua y polvo.

• Unplug the power cord when not using the

unit for long periods of time.

• Débrancher le cordon d’alimentation

lorsque l’appareil n’est pas utilisé pendant

de longues périodes.

• Desconecte el cordón de energía cuando

no utilice el equipo por mucho tiempo.

* (For apparatuses with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• No obstruya los oriﬁcios de ventilación.

• Do not let foreign objects into the unit.

• Ne pas laisser des objets étrangers dans

l’appareil.

• No deje objetos extraños dentro del

equipo.

• Do not let insecticides, benzene, and

thinner come in contact with the unit.

• Ne pas mettre en contact des insecticides,

du benzène et un diluant avec l’appareil.

• No permita el contacto de insecticidas,

gasolina y diluyentes con el equipo.

• Never disassemble or modify the unit in

any way.

• Ne jamais démonter ou modiﬁer l’appareil

d’une manière ou d’une autre.

• Nunca desarme o modiﬁque el equipo de

ninguna manera.

NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS

SOBRE EL USO

ESPAÑOLENGLISH FRANCAIS



ENGLISH

Accessories ······················································································2

Cautions on Handling ·····································································2

Cautions on Installation ·································································2

Main Features ·················································································2

Discs ·································································································2

Discs usable on the RCD-M37 ·······················································2

Holding Discs ·················································································3

Loading Discs ·················································································3

Cautions on Loading Discs ·····························································3

Cautions on Handling ·····································································3

Cautions on Storing Discs ······························································3

Cleaning Discs ···············································································3

About the Remote Control Unit ····················································3

Inserting the Batteries ····································································3

Operating Range of the Remote Control Unit ································4

Part Names and Functions ·····························································4

Front Panel ·····················································································4

Display ···························································································5

Rear Panel ······················································································5

Remote Control Unit ······································································6

Preparations ····················································································8

Cables Used for Connections ························································8

Using the AM Loop Antenna ··························································8

Assembling the AM Loop Antenna ················································8

Speaker Connections ·····································································9

Connecting the Speaker Cables ·····················································9

Connecting the Playback Components ······································ 10

Control Dock for iPod ··································································· 10

Connecting the Recording Components ···································· 10

CD Recorder / MD Recorder / Tape deck······································ 10

Connections to Other Devices ····················································· 10

Antenna Terminals ········································································ 10

USB Port ······················································································ 11

Connecting the Power Cord ························································· 11

Once Connections are Completed ·············································· 11

Turning the Power On ·································································· 11

Setting the Current Time (24-Hour Display) ······························· 12

Timer Playback··············································································22

Setting the Timer ··········································································22

Sleep Timer Playback ···································································23

Preparations ·················································································· 13

Turning the Power On ·································································· 13

Loading Discs ···············································································13

Operations Possible During Playback ········································· 13

Adjusting the Master Volume ······················································· 13

Input Source Switching ································································ 13

Adjusting the Tone ········································································ 13

Turning the Sound Off Temporarily (Muting) ································· 13

Switching the Display’s Brightness ·············································· 13

Listening with Headphones ·························································13

CD Playback ··················································································14

Playing CDs ·················································································· 14

Playing Repeatedly <Repeat Playback> ·······································14

Playing Random Order <Random Playback> ······························· 14

Playing Tracks in the Desired Order <Program playback> ············15

Switching the Display ··································································· 15

Playback of MP3 and WMA Files ················································· 15

About the MP3 and WMA Formats That Can be Played ·············· 15

Playing MP3 and WMA Files ························································ 16

TUNER Playback ··········································································· 17

Tuning in Broadcast Stations ························································ 17

Automatically Presetting FM Stations (Auto Preset) ···················· 17

Presetting FM/AM Stations Manually ·········································· 17

Listening to Preset Stations ························································· 18

Naming the Currently Tuned in Broadcast Station ························18

iPod

Playback ·············································································18

Preparations ·················································································18

Listening to Audio ········································································19

Disconnecting the iPod ································································19

Playing a Portable Audio ······························································19

Connecting a Portable Player ·······················································19

Playing the Portable Player ··························································· 19

USB Playback ················································································20

Playable USB Memory Formats ···················································20

Basic Operation ············································································20

Convenient Functions ··································································24

Auto Power On ·············································································24

Auto Function Selector Function ··················································24

Last Function Memory ·································································24

Resetting the Microprocessor ······················································24

Using an Optimizing Filter ····························································24

Getting Started

Connections

n Contents

Setup

Playback Setting the Timer

Other Functions

Troubleshooting ····························································· 25

Speciﬁcations ·································································· 26



ENGLISH

Connections Setup Playback Setting the Timer Other Functions Troubleshooting Speciﬁcations

• Before turning the power switch on

Check once again that all connections are correct and that there are

no problems with the connection cables.

•

Power is supplied to some of the circuitry even when the unit is

set to the standby mode. When traveling or leaving home for long

periods of time, be sure to unplug the power cord from the power

outlet.

• Sufﬁciently ventilate the place of installation

If the unit is left in a room full of the smoke from cigarettes, etc., for

long periods of time, the surface of the optical pickup could get dirty,

in which case it will not be able to read the signals properly.

• About condensation

If there is a major difference in temperature between the inside of

the unit and the surroundings, condensation (dew) may form on

the operating parts inside the unit, causing the unit not to operate

properly.

If this happens, let the unit sit for an hour or two with the power

turned off and wait until there is little difference in temperature

before using the unit.

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If so, move

the mobile phone away from this unit when it is in use.

• Moving the unit

Turn off the power and unplug the power cord from the power

outlet.

Next, disconnect the connection cables to other system units before

moving the unit.

•

Note that the illustrations in these instructions may differ from the

actual unit for explanation purposes.

Note:

For proper heat dispersal, do not install this unit in a conﬁned

space, such as a bookcase or similar enclosure.

b Note

Wall

q Music CDs

Discs marked with the logotype below can be played in this unit.

w CD-R/CD-RW

Discs Usable on the RCD-M37

1. High quality ampliﬁer stressing sound quality

Equippd with 30 W + 30 W (6 Ω/ohms) high quality ampliﬁer

circuits.

2. Tone control and SDB control

Separate bass and treble tone controls for adjusting the tone to your

tastes and Super Dynamic Bass (SDB) circuit for producing powerful

bass sound even when the volume is low.

Source direct position provided for turning off the SDB and tone

control circuitry to make the response ﬂat.

3. CD player for digital sound

Compact body integrating a CD section in addition to the FM/AM

tuner and ampliﬁer, allowing playback of CD-R/RW discs.

4. Playback of MP3 and WMA ﬁles

Supports playback of discs and USB memory devices on which MP3

and WMA ﬁles are recorded. The track name and artist name of the

currently playing track can be displayed on the set’s display.

The characters that can be displayed “Switching the Display”

(vpage 16)

5. Low standby power consumption

Designed with considerations on the environment, with the power

consumption when the power is in standby kept down to about 0.3 W.

Check that the following parts are supplied with the product.

q Remote control (RC-1097) ....................................................... 1

w R03/AAA batteries ................................................................... 2

e Power cord (Cord length: Approx. 6.6 ft / 2 m) ........................1

r AM loop antenna ..................................................................... 1

t FM indoor antenna .................................................................. 1

y Owner’s manual ......................................................................1

u Warranty (for North America model only) ................................1

i Service station list ................................................................... 1

Thank you for purchasing this DENON product. To ensure proper

operation, please read this owner’s manual carefully before using the

product.

After reading them, be sure to keep them for future reference.

Getting Started

q e r t

Getting Started

Accessories

Cautions on Handling

Cautions on Installation

Main Features

Discs



Connections Setup Playback Setting the Timer Other Functions Troubleshooting

ENGLISH

Speciﬁcations

Cautions on Handling

• Do not get ﬁngerprints, oil or dirt on discs.

• Take special care not to scratch discs when removing them from

their cases.

• Do not bend or heat discs.

• Do not enlarge the hole at the center.

• Do not write on the labeled (printed) surface with ball-point pens,

pencils, etc., or stick new labels on discs.

• Water droplets may form on discs if they are moved suddenly from a

cold place (outdoors for example) to a warm place, but do not try to

dry them off using a hairdryer, etc.

Cautions on Storing Discs

• Be sure to remove discs after using them.

• Be sure to store discs in their cases to protect them from dust,

scratches, warping, etc.

• Do not store discs in the following places:

1. Places exposed to direct sunlight for long periods of time

2. Dusty or humid places

3. Places exposed to heat from heating appliances, etc.

Cleaning Discs

• If there are ﬁngerprints or dirt on discs, wipe them off before using

the disc. Fingerprints and dirt can impair sound quality and cause

interruptions in playback.

• Use a commercially available disc cleaning set or a soft cloth to clean

discs.

Gently wipe the disc from the

inside towards the outside.

Do not wipe with a circular

motion.

NOTE

Do not use record spray, antistatic agents, or benzene, thinner or other

solvents.

Cautions on Loading Discs

• Only load one disc at a time. Loading two or more discs can damage

the unit or scratch the discs.

• Do not use cracked or warped discs or discs that have been repaired

with adhesive, etc.

• Do not use discs on which the sticky part of cellophane tape or labels

is exposed or on which there are traces of where labels have been

removed. Such discs can get caught inside the player and damage

it.

Inserting the Batteries

q Slide the rear lid in the

direction of the arrow and

remove it.

w Load the two batteries properly

as indicated by the marks in the

battery compartment.

e Put the rear cover back on.

Figure 1

• “00 Tr 00 : 00” is displayed if a disc that cannot be played is loaded.

• “00 Tr 00 : 00” is displayed if the disc is loaded upside-down or if no

disc is loaded.

Do not touch the signal surface.

Holding Discs

• Set the disc with the labeled side facing up.

• Make sure the disc tray is fully open when inserting the disc.

• Place the discs ﬂatly, 12 cm discs in the outer tray guide (Figure 1), 8

cm discs in the inner tray guide (Figure 2).

Loading Discs

12 cm disc

8 cm disc

Outer tray guide Inner tray guide

Figure 2

• Place 8 cm discs in the inner tray guide without using an adapter.

NOTE

Do not push the disc tray in by hand when the power is turned off.

Doing so could damage the set.

Getting Started

About the Remote Control Unit

NOTE

• Discs with special shapes (heart-shaped discs, octagonal discs, etc.)

cannot be played. Do not attempt to play them, as doing so can

damage the product.

• Some discs and some recording

formats may not be playable.

• Non-ﬁnalized discs cannot be

played.

b What is ﬁnalization?

Finalization is the process that

makes recorded CD-R/CD-RW discs playable on compatible

players.



ENGLISH

Connections Setup Playback Setting the Timer Other Functions Troubleshooting Speciﬁcations

q w e r t y u oi Q1

Q2Q3Q4

Q6 Q5

For buttons not explained here, see the page indicated in parentheses ( ).

Front Panel

q Power operation button

(ON/STANDBY) ······································································ (13)

w Power indicator ······································································ (13)

e USB port (USB) ······································································ (11)

r Display

t Portable jack (PORTABLE IN) ················································(19)

y Headphones jack (PHONES) ················································· (13)

u SOURCE button ····································································· (13)

i Revers-skip/Forward-skip buttons

(8/–, +/9) ································································· (14, 17)

o Master volume control knob

(VOLUME) ··············································································(13)

Q0 MENU/SET button ·························································· (12, 22)

Q1 SDB/TONE button ································································ (13)

Q2 BAND/Stop button (BAND/2) ········································ (14, 17)

Q3 Play/Pause button (1/3) ·······················································(14)

Q4 Disc tray open/close button (5) ··········································· (13)

Q5 Remote control sensor ···························································(4)

Q6 Disc tray ···················································································(3)

30°

NOTE

• Replace the batteries with new ones if the set does not operate even

when the remote control unit is operated close to the unit.

• The supplied batteries are only for verifying operation.

• When inserting the batteries, be sure to do so in the proper direction,

following the “q” and “w” marks in the battery compartment.

• To prevent damage or leakage of battery ﬂuid:

• Do not use a new battery together with an old one.

• Do not use two different types of batteries.

• Do not attempt to charge dry batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in

ﬂames.

• If the battery ﬂuid should leak, carefully wipe the ﬂuid off the inside

of the battery compartment and insert new batteries.

• Remove the batteries from the remote control unit if it will not be in

use for long periods.

Point the remote control unit at the remote sensor when operating it.

Operating Range of the Remote Control

Unit

NOTE

The set may function improperly or the remote control unit may not

operate if the remote control sensor is exposed to direct sunlight,

strong artiﬁcial light from an inverter type ﬂuorescent lamp or infrared

light.

Approx. 23 feet / 7 m

Getting Started

Part Names and Functions



ENGLISH

Connections Setup Playback Setting the Timer Other Functions Troubleshooting Speciﬁcations

y r

Rear Panel

q Monaural audio connector

(MONO OUT) ···············································(9)

w Speakers terminals ······································(9)

e AC inlet (AC IN) ·········································· (11)

r FM/AM antenna terminals ························ (10)

t DOCK CONTROL jack ································ (10)

y AUX1/AUX2

Analog audio connectors ·························· (10)

q w e r t y u i

q Information display

Various information is displayed here, depending

on the operation mode.

w 1: (the play indicator) lights when a disc is

playing.

3: (the pause indicator) lights when a disc is

pausing.

e SDB, TONE indicator ………………………(13)

r Reception mode indicator …………………(17)

t TOTAL indicator

Lights when the total number of tracks and total

time of the CD are displayed.

y Play mode indicator ·································· (14)

u Timer indicator ·········································· (23)

i F: Flashes when remote control signals are

received.

Display

Getting Started



Connections Setup Playback Setting the Timer Other Functions Troubleshooting

ENGLISH

Speciﬁcations

Remote Control Unit

Buttons Operable for All Functions (CD, TUNER, iPod and USB) Buttons Operable When the Function is Set to “CD”

The buttons listed at “Buttons Operable for All Functions” can also be used.

q DIMMER button ·········································· (13)

w Master volume control buttons

(VOLUME) ··················································· (13)

e SDB/TONE button ······································ (13)

r MENU/SET button ····································· (12)

t ON/STANDBY button ································· (13)

y SLEEP button ·············································· (23)

u MUTE button ·············································· (13)

i CLOCK button ············································· (12)

q Number buttons ········································· (14)

w PROG/DIRECT button ································ (15)

e RANDOM button ········································ (14)

r SOURCE button ·········································· (14)

t CD 1/3 button ············································ (14)

y FOLDER MODE button ······························· (16)

u TIME/DISPLAY button ································ (15)

i CLEAR/DEL button ····································· (15)

o REPEAT button ············································ (14)

Q0 Fast-reversing/Fast-forwarding buttons

(6, 7) ··················································· (14)

Q1 Reverse-skip/Forward-skip buttons

(8, 9) ··················································· (14)

Q2 Stop button (2) ··········································· (14)

Q3 Cursor buttons (uio p) ·························· (16)

Getting Started

NOTE

The DAB/RDS button cannot be used.



ENGLISH

Connections Setup Playback Setting the Timer Other Functions Troubleshooting Speciﬁcations

q Number buttons ········································· (18)

w SOURCE button ·········································· (17)

e TUNER button ············································· (17)

r CLEAR/DEL button ····································· (18)

t Tuning +, – buttons (TU+, TU–) ·················· (17)

y Channel +, – buttons (CH+, CH–) ··············· (17)

u Stop button (2) ··········································· (17)

i ENTER/MEMO button ································ (17)

o Cursor buttons (uio p) ·························· (17)

q Number buttons ········································· (21)

w RANDOM button ········································ (21)

e SOURCE button ·········································· (20)

r MENU/SET button ····································· (19)

t FOLDER MODE button ······························· (21)

y TIME/DISPLAY button ································ (19)

u REPEAT button ············································ (21)

i Fast-reversing/Fast-forwarding buttons

(6, 7) ···················································(21)

o Reverse-skip/Forward-skip buttons

(8, 9) ··················································· (21)

Q0 USB 1/3 button ········································· (20)

Q1 Stop button (2) ··········································· (21)

Q2 iPod 1/3 button ········································ (19)

Q3 ENTER/MEMO button ································ (19)

Q4 Cursor buttons (uio p) ·························· (19)

Q5 REMOTE/BROWSE button ························· (18)

Buttons Operable When the Function is Set to “TUNER”

The buttons listed at “Buttons Operable for All Functions” can also be used.

Buttons Operable When the Function is Set to “iPod”, “USB”

The buttons listed at “Buttons Operable for All Functions” can also be used.

Getting Started



ENGLISH

Getting Started Setup Playback Setting the Timer Other Functions Troubleshooting Speciﬁcations

Audio cables

Analog connections (stereo)

(White)

(Red)

Stereo pin-plug cable

Analog connections (subwoofer)

(Black)

Pin-plug cable

Speaker connections

Speaker cable

Signal direction

Audio signal:

Output

Input

Output

Nail, tack, etc.

NOTE

• Do not plug in the power cord until all connections have been

completed.

• When making connections, also refer to the owner’s manual of the

other components.

• Be sure to connect the left and right channels properly (left with left,

right with right).

• Do not bundle power supply cords together with connection cables.

Doing so can result in humming or noise.

Connections for all compatible audio signal formats are described

in this owner’s manual. Please select the types of connections

suited for the equipment you are connecting.

With some types of connections, certain settings must be made

on the RCD-M37. For details, refer to the instructions for the

respective connection items below.

Select the cables according to the equipment being connected.

Preparations

Cables Used for Connections

Using the AM Loop Antenna

n To use suspended on a wall

Suspend directly on the wall without assembling.

n To use standing alone

Use the procedure below to assemble.

Assembling the AM Loop Antenna

Bend in the direction of the arrow.

Insert into the hole.

Connections



Getting Started Setup Playback Setting the Timer Other Functions Troubleshooting

ENGLISH

Speciﬁcations

Check the left (L) and right (R) channels and the + (red) and – (black)

terminals on the set and the speakers to be used and interconnect

the cables to the same polarities.

(R) (L)

w q w q

Connecting the Speaker Cables

Peel off about 10 mm of the sheathing at

the tip of the cable, twist the core wire and

terminate it.

Turn the speaker terminal counterclockwise

to loosen it.

Insert the speaker cable’s core wire into the

base of the speaker terminal.

Turn the speaker terminal counterclockwise

to tighten it.

NOTE

• Use speakers with an impedance of 6 to 16 Ω/ohms. The protection

circuit may be activated if speakers with an impedance other than

speciﬁed are used.

• Connect the speaker cables in a way that they do not stick out of the

speaker terminals. The protection circuit may be activated if the core

wires touch the rear panel or screws or if the + and – sides touch.

• Never touch the speaker terminals while the power is on. Doing so

could cause electric shock.

Protector circuit

The protection circuit will be activated in the following cases:

• When the speaker cable's core wires are touching the rear

panel or screws or when the speaker cable’s + and – sides are

touching

• When the surrounding temperature is extremely high

• When the internal temperature rises due to extended use with a

high output

If this happens, unplug the power cord, then check the connections

of the speaker cables and input cables. If the set’s temperature

is extremely high, wait for it to cool off and improve surrounding

ventilation. After doing this, plug the power cord back in.

If the protection circuit is activated though there are no problems

in ventilation around the set or in connections, the set could be

damaged. Turn off the power, then contact a DENON servicing and

inquiry outlet.

Speaker SC-M37 (Supplied)

Subwoofer

with built-in

ampliﬁer

Connections

Speaker Connections

When using a banana plug

Tighten the speaker terminal ﬁrmly before inserting the banana

plug.

0

ENGLISH

Getting Started Setup Playback Setting the Timer Other Functions Troubleshooting Speciﬁcations

"4%/8

iPod

3- 3-

*/ 065

"6%*0

Control Dock for iPod CD Recorder / MD Recorder / Tape deck

Antenna Terminals

AM loop antenna

(Supplied)

FM indoor antenna

(Supplied)

Black White

CD recorder /

MD recorder /

Tape deck

Use a DENON Control Dock for iPod (ASD-1R or ASD-3N/3W, sold

separately ) to connect the set with an iPod.

• When using a Control Dock for iPod, the Control Dock for iPod must

be set. For details, refer to the operating instructions of the Control

Dock for iPod.

• To use an iPod, see “iPod

Playback” (vpage 18).

AM/FM

The AM and FM reception sensitivity depends on the place the antenna

is set and the direction in which it is set. Set it so that reception is

best.

Connections

Connecting the Playback

Components

Connecting the Recording

Components

Connections to Other Devices

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, speciﬁes that the cable

ground shall be connected to the grounding system of the building,

as close to the point of cable entry as practical.



Getting Started Setup Playback Setting the Timer Other Functions Troubleshooting

ENGLISH

Speciﬁcations

USB Port Connecting the Power Cord

NOTE

• Only use the supplied power cord.

• Be sure the power cord is unplugged from the power outlet before

connecting or disconnecting it to the AC IN.

Power cord (Supplied)

To household power outlet

(AC 120 V, 60 Hz)

Turning the Power On

(vpage 13)

NOTE

• It is not possible to connect and use a computer via the RCD-M37’s

USB port using a USB cable.

• For details about USB memory devices, see “Playable USB Memory

Formats” (vpage 20).

USB

Connections

Once Connections are

Completed

NOTE

• Make sure the AM loop antenna lead terminals do not touch metal

parts of the panel.

• Do not connect two FM antennas simultaneously.

n Connecting the AM loop antenna

Push the lever.

Insert the conductor.

Return the lever.



ENGLISH

Getting Started Connections Setting the Timer Other Functions Troubleshooting Speciﬁcations

<1/3><5>

ON/STANDBY

SOURCE

MENU/SET

SDB/TONE

8, 9

ON/STANDBY

[MUTE]

[o p]

[ENTER/MEMO]

8, 9

[VOLUME df]

MENU/SET

SDB/TONE

[CLOCK]

SOURCE

[DIMMER]

[CD 1/3]

Button located on both the main unit and the remote control

unit

BUTTON

Button only on the main unit

Button only on the remote control unit

[BUTTON]

Symbols used to indicate buttons in this manual

GExampleH Setting the current time to 10:15 am

Press ON/STANDBY to turn the power on.

Press [CLOCK].

The current time is displayed.

Press MENU/SET for over 1 second to set the manual

time setting mode.

The “hours” display ﬂashes.

Use 8, 9 or [o p] to set the “hours”.

Press MENU/SET or [ENTER/MEMO].

The “minutes” display ﬂashes.

Use 8, 9 or [o p] to set the “minutes”.

Press MENU/SET or [ENTER/MEMO].

The current time is set, and the normal display reappears.

TIME Adj AM12:00TIME Adj AM12:00

TIME Adj AM10:00TIME Adj AM10:00

TIME Adj AM10:15TIME Adj AM10:15

n Checking the current time when the power is on

Press [CLOCK].

When pressed again or if a different operation is performed, the

normal display reappears.

n Checking the current time when the power is set

to standby

Press MENU/SET or [CLOCK].

Press again to turn off display.

• Displaying the time when the power is set to standby consumes

electricity. To reduce electric consumption, turn the time display off.

• When the function is set to iPod, the current time cannot be set.

Setup Playback

Setup

Setting the Current Time

(12-Hour Display)



Getting Started Connections Setup Setting the Timer Other Functions Troubleshooting

ENGLISH

Speciﬁcations

Press [DIMMER].

b The display’s brightness switches each time the button is

pressed.

SDB

: Switches Super Dynamic Bass on and off.

BASS

: Adjusts the bass sound.

[Variable range]

–10dB

+10dB

TREBLE

: Adjusts the treble sound.

[Variable range]

–10dB

+10dB

S.DIRECT

: Turns SDB, bass and treble off.

Settings made upon purchase :

• SDB ·····················OFF • TREBLE ················ 0 dB

• BASS ·················· 0 dB • S. DIRECT ·············OFF

100 %

[Variable range]

VOLUME 00 ~ 45, VOLUME MAX

Press SOURCE to select the input source.

AUX1

(AUX1/Dock)

USB

TUNERCD

PORTABLE IN AUX2

b “AUX1/Dock” is displayed when a Control Dock for iPod is

connected to “AUX1”.

b “PORTABLE IN” is only displayed when connected.

Plug the headphones (sold separately) into the <PHONES>.

The sound from the speakers is automatically cut off.

In the stop mode, press <5> to open the disc tray.

b “Loading discs” (vpage 3).

Adjusting the Master Volume

n To close the disc tray

Press <5> again.

b The disc tray also closes when <1/3>, [CD 1/3] or SOURCE is

pressed.

NOTE

Do not place any foreign objects in the disc tray. Doing so could

damage it.

Either turn <VOLUME> or press [VOLUME df].

The volume level is displayed.

Input Source Switching

Select the item to be adjusted with SDB/TONE.

BASS

TREBLE

S.DIRECT

SDB

GAbout the displayH

When the SDB is on ∙∙∙∙∙∙∙∙∙∙∙∙ “SDB” is displayed.

When BASS or TREBLE is set to something other than 0 dB

∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ “TONE” is displayed.

Display the mode you want to adjust, then use 8,

9 and [o p] to turn on or off and to adjust the

tone.

b If no operation is performed for 5 seconds, the adjustment is

retained and the normal display reappears.

NOTE

Be careful not to set the volume too high when using headphones.

Adjusting the Tone

Turning the Sound Off Temporarily

(Muting)

Press [MUTE].

The “MUTE ON” is displayed.

Loading Discs

Listening with Headphones

[Selectable modes]

To cancel, press [MUTE] again.

(The mute mode is also canceled when the <VOLUME> control is

turned or a [VOLUME df] is pressed.)

Switching the Display’s Brightness

70 % 40 %

OFF

Playback

Turning the Power On

NOTE

• Power continues to be supplied to some of the circuitry even when

the power is in the standby mode. When leaving home for long

periods of time or when traveling, either press ON/STANDBY to turn

off the power, or unplug the power cord from the power outlet.

• Be sure to stop playback before turning the power off.

Press ON/STANDBY.

• The power turns on. Press again to set the power to standby.

• Power indicator

Standby ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙Red

Power on ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙Green

When the timer is set ∙∙∙∙∙∙∙∙∙∙∙∙Orange

n Completely turning off the power

Unplug the power cord from the wall outlet.

b Note that the time setting is cleared when the power cord is

unplugged from the outlet.

b The settings made for the various functions may be cleared if the

power cord is left unplugged from a power outlet for an extended

period of time.

Preparations

Playback

Operations Possible During

Playback



ENGLISH

Getting Started Connections Setup Setting the Timer Other Functions Troubleshooting Speciﬁcations

1/3

<BAND/

8, 9

SOURCE

[NUMBER]

[PROG/DIRECT]

[RANDOM]

[CD 1/3]

SOURCE

[REPEAT]

[CLEAR/DEL]

[6, 7]

[TIME/DISPLAY]

[2]

8, 9

Press [REPEAT].

Playback in the respective repeat mode starts.

In the stop mode, press [RANDOM].

The “RANDOM” indicator lights.

Press <1/3> or [CD 1/3].

The tracks start playing in random order.

(Single-track repeat)

: Only 1 track is played repeatedly.

ALL

(All-track repeat)

: All tracks are played repeatedly.

Repeat off (indicator turns off)

: Normal playback resumes.

Press <1/3> or [CD 1/3].

The “1” indicator lights and playback begins.

Single-track repeat All-track repeat

Repeat off

(indicator turns off)

n Stopping Playback

Press <BAND/2> or [2].

n Stopping Playback Temporarily

Press <1/3> or [CD 1/3].

The “3” is displayed.

b To resume playback, press <13> or [CD 1/3].

n Fast-Forwarding and Fast-Reversing (searching)

During playback, press and hold in [6, 7].

n Moving to the Beginning of Tracks (skipping)

During playback, press 8, 9.

b The disc is skipped the number of tracks equal to the number of

times the button is pressed.

b When pressed once in the return direction, playback returns to the

beginning of the currently playing track.

To Play the Desired Track

(Remote Control Unit Only)

Press [NUMBER] (0 ~ 9, +10) to select the track.

GExampleH : Track 4 : [4]

GExampleH : Track 12 : [+10], [2]

GExampleH : Track 20 : [+10], [+10], [0]

Playing Repeatedly <Repeat Playback>

Playing Random Order <Random Playback>

Button located on both the main unit and the remote control

unit

BUTTON

Button only on the main unit

Button only on the remote control unit

[BUTTON]

Symbols used to indicate buttons in this manual

Playing CDs

• If the function is set to something other than “CD”, press [CD 1/3]

to switch the function to “CD” and start playback ( vpage 24 “Auto

Function Selector Function”).

• The function can also be switched to “CD” using SOURCE.

[Selectable items]

NOTE

Random play cannot be set or canceled during playback.

Playback

n Canceling Random Playback

In the stop mode, press [RANDOM].

The “RANDOM” indicator turns off.

NOTE

When [REPEAT] pressed during random playback, the tracks are played

in a different random order after this turn.

CD Playback



Getting Started Connections Setup Setting the Timer Other Functions Troubleshooting

ENGLISH

Speciﬁcations

There are many music distribution sites on the Internet allowing you

to download music ﬁles in MP3 or WMA (Windows Media

Audio)

format. The music (ﬁles) downloaded from such sites can be stored on

CD-R or CD-RW discs and played on the RCD-M37.

“Windows Media” and “Windows” are registered trademarks or

trademarks in the United States and other countries of Microsoft

Corporation of the United States.

• Be sure to give ﬁles the extension “.MP3” or “.WMA”. Files with any

other extensions or with no extensions cannot be played.

• Recordings you have made should only be used for your personal

enjoyment, and as per copyright laws may not be used in other ways

without permission of the copyright holder.

File format

MPEG-1 Audio Layer-3

WMA (Windows Media Audio)

Playing Tracks in the Desired Order

Up to 25 tracks can be programmed.

In the stop mode, press [PROG/DIRECT].

The “PGM” indicator lights.

Use [NUMBER] (0 ~ 9, +10) to select the traks.

b GExampleH To program tracks 3, 12, 7 to play in that order:

Press [PROG/DIRECT], [3], [+10], [2], [7].

Press <1/3> or [CD 1/3].

Playback starts in the programmed order.

n Checking the order of the programmed tracks

In the stop mode, press 9 or 8.

The track numbers are displayed in the programmed order each

time the button is pressed.

n To clear the last track programmed

In the stop mode, press [CLEAR/DEL].

The last track programmed is cleared each time the button is

pressed.

n To clear one programmed track at a time

In the stop mode, use 9 or 8 to select the track to be

cleared, then press [CLEAR/DEL].

n Clearing the all programmed track

In the stop mode, press [PROG/DIRECT].

The “PGM” indicator turns off.

Playable MP3/WMA ﬁle

File format

Sampling

frequency

Bit rate Extension

MP3 32, 44.1, 48 kHz 32 ~ 320 kbps .MP3

WMA 32, 44.1, 48 kHz 64 ~ 160 kbps .WMA

When [REPEAT] is pressed, the tracks are played repeatedly in the

programmed order.

About the MP3 and WMA Formats That

Can be Played

CD-R and CD-RW discs created in the format described below can be

played.

Writing software format

ISO9660 level 1

b When written in other formats, it may not be possible to play the

disc properly.

Maximum number of playable ﬁles and folders

Total number of folders + ﬁles: 512

Maximum number of ﬁles in a folder: 255

Tag data

ID3-Tag (Ver.1x)

META-Tag (Compatible with title, artist and album names)

Playback

Press

[TIME/DISPLAY]

b The display switches each time the button is pressed.

Elapsed time of

currently playing track

Remaining time of

currently playing track

Switching the Display

Remaining time for

all remaining tracks

Playback of MP3 and WMA Files



ENGLISH

Getting Started Connections Setup Setting the Timer Other Functions Troubleshooting Speciﬁcations

(The “Not Support” is displayed.)

Note that depending on the software used for burning and other

conditions, some ﬁles may not play or display correctly.

<1/3>

MENU/SET

SOURCE

8, 9

[CD 1/3]

[TUNER]

SOURCE

MENU/SET

[TIME/DISPLAY]

8, 9

[CH –, CH +]

[REPEAT]

[TU –, TU +]

[2]

[FOLDER MODE]

[ENTER/MEMO]

[NUMBER]

[

uio p

]

Switching the Display

During playback, press [TIME/DISPLAY].

b The characters that can be displayed are as follows:

A to Z a to z 0 to 9

’ ( ) * + , - . / =

(space)

When “Folder Mode” is selected:

1FLD

: Only the selected track is played repeatedly.

FLD

: All the ﬁles in the selected folder are played repeatedly.

FLD

: Folder mode playback resumes.

When “Disc Mode” is selected:

“Playing Repeatedly <Repeat playback>” (vpage 14)

To Play Repeatedly

Press [REPEAT].

Playback starts in the respective repeat mode.

b The selectable repeat modes differ in the “Folder Mode” and the

“Disc Mode”.

When “Folder Mode” is selected:

When “Disc Mode” is selected:

Title/album display

[Selectable items]

Button located on both the main unit and the remote control

unit

BUTTON

Button only on the main unit

Button only on the remote control unit

[BUTTON]

Symbols used to indicate buttons in this manual

Playing MP3 and WMA Files

Load a CD-R or CD-RW disc containing music les in

the MP3 or WMA format into the disc tray (vpage

3).

Press [FOLDER MODE] and select “Folder Mode” or

“Disc Mode”.

GAbout the displayH

When “Folder Mode” is selected ∙∙∙∙∙“FLD” is displayed.

When “Disc Mode” is selected ∙∙∙∙∙∙∙∙“FLD” is not displayed.

Folder Mode :

All the files in the selected folder are played.

Disc Mode :

After the selected folder and files are played, all the files in all the

folders are played.

Use [ui] to select the folder to be played.

Use 8, 9 or [o p] to select the le to be

played.

Press <1/3> or [CD 1/3].

n To switch the Folder or File During Playback

• Folder

Use [ui] to select the folder.

• File

Use 8, 9 to select the ﬁle, or use [NUMBER] (0 ~ 9, +10) to

select the ﬁle number.

b The ﬁle numbers are set automatically when the disc is loaded.

File name display Title/artist display

Single-track repeat All-track repeat

Repeat off

(indicator turns off)

Single-track repeat Repeat of all the

tracks in the folder

Repeat off

n Setting random playback

“Playing Random Order <Random playback>” (vpage 14)

Programmed playback is not possible with MP3/WMA discs.

Playback

La pagina sta caricando ...

Denon D-M37 Manuale del proprietario

Marca: Denon

Modello: D-M37

Categoria: Lettore CD

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

RCD-M37

Scarica il pdf

rapporto

in altre lingue

English: Denon D-M37 Owner's manual

Denon D-M37 Manuale del proprietario

Questo manuale è adatto anche per

Denon D-M37 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti