Netgear WG311NAR Manuale utente

202-10091-03

February 2007

NETGEAR, Inc.

4500 Great America Parkway

Santa Clara, CA 95054 USA

NETGEAR 54 Mbps

Wireless PCI Adapter

WG311v3 User Manual

ii

v3.0, February 2007

Technical Support

Please refer to the support information card that shipped with your product. By registering your

product at http://www.netgear.com/register, we can provide you with faster expert technical

support and timely notices of product and software upgrades.

NETGEAR, INC. Support Information

Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support

information card.

E-mail: support@netgear.com

Website: http://www.netgear.com

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to

make changes to the products described in this document without notice.

NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit

layout(s) described herein.

or registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Microsoft and Windows are

registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product

names are trademarks or registered trademarks of their respective holders. Information is subject to change without

Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications

Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,

building materials and construction, and network overhead, lower actual data throughput rate.

Safety and Regulatory Notices

FCC Statement

The WG311 v3 has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of

the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

v3.0, February 2007

iii

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver’s

• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any change or modification to the product not expressly approved by Netgear could void the user’s

authority to operate the device.

FCC RF Radiation Exposure and SAR Statements

SAR Statement

The NETGEAR WG311 v3 has been tested for body-worn Specific Absorption Rate (SAR) compliance. The FCC has

established detailed SAR requirements and has established that these requirements have been met while installed in host

notebook computer.

RF Exposure Information

The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the

requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency

devices. This model meets the applicable government requirements for exposure to radio frequency waves. The highest

SAR level measured for this device was 0.74 W/kg.

Canadian Department of Communications Industry Canada (IC) Notice

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe B

est conforme à la norme NMB-003 et CNR-210 du Canada.

“To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from

windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to

licensing.”

“Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit être utilisé à

l’intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son

antenne d’émission) est installé à l’extérieur, il doit faire l’objet d’une licence.”

Europe – EU Declaration of Conformity

A printed copy of the EU Declaration of Conformity certificate for this product is provided in the WG311 v3 product

package.

Èesky

[Czech]

NETGEAR, Inc. tímto prohlašuje, že tento NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3

je ve shodì se základními požadavky a dalšími pøíslušnými ustanoveními

smìrnice 1999/5/ES.

Dansk

[Danish]

Undertegnede NETGEAR, Inc. erklærer herved, at følgende udstyr NETGEAR 54 Mbps

Wireless PCI Adapter WG311 v3

overholder de væsentlige krav og øvrige relevante krav i

direktiv 1999/5/EF.

Deutsch

[German]

Hiermit erklärt NETGEAR, Inc., dass sich das Gerät NETGEAR 54 Mbps Wireless PCI

Adapter WG311 v3 in Übereinstimmung mit den grundlegenden Anforderungen und den

übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

v3.0, February 2007

iv

Eesti

[Estonian]

Käesolevaga kinnitab NETGEAR, Inc. seadme NETGEAR 54 Mbps Wireless PCI

Adapter WG311 v3

vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist

tulenevatele teistele asjakohastele sätetele.

English Hereby, NETGEAR, Inc., declares that this NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3

is in compliance with the essential requirements and other relevant provisions

of Directive 1999/5/EC.

Español

[Spanish]

Por medio de la presente NETGEAR, Inc. declara que el NETGEAR 54 Mbps Wireless

PCI Adapter WG311 v3

cumple con los requisitos esenciales y cualesquiera otras

disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR, Inc. ΔΗΛΩΝΕΙ ΟΤΙ NETGEAR 54 Mbps Wireless

PCI Adapter WG311 v3

ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ

ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français

[French]

Par la présente NETGEAR, Inc. déclare que l'appareil NETGEAR 54 Mbps Wireless PCI

Adapter WG311 v3

est conforme aux exigences essentielles et aux autres dispositions

pertinentes de la directive 1999/5/CE.

Italiano

[Italian]

Con la presente NETGEAR, Inc. dichiara che questo NETGEAR 54 Mbps Wireless PCI

Adapter WG311 v3

è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti

stabilite dalla direttiva 1999/5/CE.

Latviski

[Latvian]

Ar šo NETGEAR, Inc. deklarç, ka NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3

atbilst Direktîvas 1999/5/EK bûtiskajâm prasîbâm un citiem ar to saistîtajiem noteikumiem.

Lietuviø

[Lithuanian]

Šiuo NETGEAR, Inc. deklaruoja, kad šis NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3

atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Nederlands

[Dutch]

Hierbij verklaart

NETGEAR, Inc. dat het toestel NETGEAR 54 Mbps Wireless PCI

Adapter WG311 v3

in overeenstemming is met de essentiële eisen en de andere relevante

bepalingen van richtlijn 1999/5/EG.

Malti

[Maltese]

Hawnhekk, NETGEAR, Inc., jiddikjara li dan NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3

jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-

Dirrettiva 1999/5/EC.

Magyar

[Hungarian]

Alulírott,

NETGEAR, Inc. nyilatkozom, hogy a NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3

megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv

egyéb elõírásainak.

Polski [Polish] Niniejszym NETGEAR, Inc. oœwiadcza, ¿e NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3

jest zgodny z zasadniczymi wymogami oraz pozosta³ymi stosownymi

postanowieniami Dyrektywy 1999/5/EC.

Português

[Portuguese]

NETGEAR, Inc. declara que este NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3

está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Slovensko

[Slovenian]

NETGEAR, Inc. izjavlja, da je ta NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 v

skladu z bistvenimi zahtevami in ostalimi relevantnimi doloèili direktive 1999/5/ES.

Slovensky

[Slovak]

NETGEAR, Inc. týmto vyhlasuje, že NETGEAR 54 Mbps Wireless PCI Adapter WG311

v3

spåòa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

v3.0, February 2007

v

Product and Publication Details

Suomi

[Finnish]

NETGEAR, Inc. vakuuttaa täten että NETGEAR 54 Mbps Wireless PCI Adapter WG311

v3

tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien

direktiivin muiden ehtojen mukainen.

Svenska

[Swedish]

Härmed intygar NETGEAR, Inc. att denna [utrustningstyp] står I överensstämmelse med

de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

1999/5/EG.

Model Number: WG311 v3

Publication Date: February 2007

Product Family: Wireless PCI Adapter

Product Name: NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3

Home or Business Product: Home

Language: English

Publication Part Number: 202-10091-03

v3.0, February 2007

vi

vii

v3.0, February 2007

Contents

About This Manual

Conventions, Formats, and Scope ................................................................................... ix

How to Use This Manual ...................................................................................................x

How to Print this Manual ....................................................................................................x

Chapter 1

Basic Setup

What You Need Before You Begin ..................................................................................1-1

Verify System Requirements ....................................................................................1-1

Observe Wireless Location and Range Guidelines ..................................................1-2

What Is in the Box ..........................................................................................................1-2

WG311 v3 Default Wireless Settings ..............................................................................1-2

Installation ......................................................................................................................1-3

Connecting to Wireless Networks and the Internet ........................................................1-7

WG311 v3 Icon Colors .............................................................................................1-8

The Smart Wizard Status Bar ...................................................................................1-8

WG311 v3 LED ........................................................................................................1-9

Removing the WG311 v3 Software ...............................................................................1-10

Upgrading the WG311 v3 Software ..............................................................................1-10

Chapter 2

Network Connections and Wireless Security

Disabling the Windows Zero Configuration Utility ...........................................................2-1

Understanding the Smart Wizard ...................................................................................2-2

Viewing Wireless Networks in Your Area ........................................................................2-2

Finding a Network ...........................................................................................................2-4

Profiles ............................................................................................................................2-5

Adding Profiles .........................................................................................................2-5

Setting up a Profile to Connect to an Access Point or Router ........................................2-6

Setting up a Computer-to-Computer (Ad Hoc) Profile ....................................................2-7

Starting a Computer-to-Computer (Ad Hoc) Network Connection ...........................2-9

viii

v3.0, February 2007

Wireless Security ..........................................................................................................2-10

Using Wireless Security Features ................................................................................2-10

Wireless Network Name (SSID) and Security Settings ................................................2-11

Setting up WEP Encryption Security ............................................................................2-12

Setting up WPA2-PSK Security ....................................................................................2-14

Setting up WPA-PSK Security ......................................................................................2-15

Advanced Settings ........................................................................................................2-16

Statistics Page ..............................................................................................................2-16

About Page ...................................................................................................................2-17

Chapter 3

Troubleshooting

Troubleshooting Tips ......................................................................................................3-1

Ad Hoc Mode is Not Working Correctly ..........................................................................3-3

Windows XP Occasional Connection Problems .............................................................3-3

Appendix A

Technical Specifications

Appendix B

Related Documents

ix

v3.0, February 2007

About This Manual

The NETGEAR

®

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual describes

how to install, configure and troubleshoot the NETGEAR 54 Mbps Wireless PCI Adapter WG311

v3. The information in this manual is intended for readers with intermediate computer and Internet

skills.

Conventions, Formats, and Scope

The conventions, formats, and scope of this manual are described in the following paragraphs:

• Typographical Conventions. This manual uses the following typographical conventions:

• Formats. This manual uses the following formats to highlight special messages:

• Scope. This manual is written for the WG311 v3 Wireless PCI Adapter according to these

specifications:

Italics Emphasis, books, CDs, URL names

Bold User input

Note: This format is used to highlight information of importance or special interest.

Tip: This format is used to highlight a procedure that will save time or resources.

Product Version NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3

Manual Publication Date February 2007

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

x

v3.0, February 2007

For more information about network, Internet, firewall, and VPN technologies, see the links to the

NETGEAR website in Appendix B, “Related Documents”.

How to Use This Manual

The HTML version of this manual includes the following:

• Buttons, and , for browsing forwards or backwards through the manual one page

at a time

• A button that displays the table of contents and an button. Double-click on a

link in the table of contents or index to navigate directly to where the topic is described in the

manual.

• A button to access the full NETGEAR, Inc. online knowledge base for the product

model.

• Links to PDF versions of the full manual and individual chapters.

How to Print this Manual

To print this manual you can choose one of the following several options, according to your needs.

• Printing a Page in the HTML View.

Each page in the HTML version of the manual is dedicated to a major topic. Use the Print

button on the browser toolbar to print the page contents.

• Printing a Chapter.

Use the PDF of This Chapter link at the top left of any page.

– Click the PDF of This Chapter link at the top left of any page in the chapter you want to

print. The PDF version of the chapter you were viewing opens in a browser window.

– Your computer must have the free Adobe Acrobat reader installed in order to view and

print PDF files. The Acrobat reader is available on the Adobe website at

http://www.adobe.com.

Note: Product updates are available on the NETGEAR, Inc. website at

http://kbserver.netgear.com/products/WG311 v3.asp.

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

xi

v3.0, February 2007

– Click the print icon in the upper left of the window.

• Printing the Full Manual.

Use the Complete PDF Manual link at the top left of any page.

– Click the Complete PDF Manual link at the top left of any page in the manual. The PDF

version of the complete manual opens in a browser window.

– Click the print icon in the upper left of the window.

Tip: If your printer supports printing two pages on a single sheet of paper, you can

save paper and printer ink by selecting this feature.

Tip: If your printer supports printing two pages on a single sheet of paper, you can

save paper and printer ink by selecting this feature.

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

xii

v3.0, February 2007

1-1

v3.0, February 2007

Chapter 1

Basic Setup

The NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 lets you connect a PC computer to

wireless networks. It is designed for PC computers running Microsoft Windows. For information

about product features and compatible NETGEAR products, see the NETGEAR website at

http://www.netgear.com.

This chapter describes how to install your WG311 v3 Wireless PCI Adapter and set up basic

wireless connectivity on your Wireless Local Area Network (WLAN). Advanced wireless network

settings are covered in Chapter 2, “Network Connections and Wireless Security”.

What You Need Before You Begin

You need to verify that your computer meets the minimum system requirements and get the

wireless network configuration settings of the WLAN where you will connect before you can

configure your wireless PCI adapter and connect.

Verify System Requirements

Before installing the WG311 v3 Wireless PCI Adapter, please make sure that these minimum

requirements have been met:

• Pentium

®

III class computer with an available PCI slot

•CD drive

• 20 Mbytes of free hard disk space

• Some versions of Windows may ask for the original Windows operating system installation

files to complete the installation of the WG311 v3 driver software

Note: Indoors, computers can connect to wireless networks at distances of several

hundred feet. Because walls do not always block wireless signals, others outside

your immediate area could access your network. It is important to take steps to

secure your network from unauthorized access. The WG311 v3 Wireless PCI

Adapter provides highly effective security features, which are covered in “Wireless

Security” on page 2-10. Deploy the security features appropriate to your needs.

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-2

v3.0, February 2007

Observe Wireless Location and Range Guidelines

Computers can connect over wireless networks indoors at a range which vary significantly based

on the physical location of the computer with the NETGEAR 54 Mbps Wireless PCI Adapter

WG311 v3. For best results, avoid potential sources of interference, such as:

• Large metal surfaces

•Microwaves

• 2.4 GHz Cordless phones

In general, wireless devices can communicate through walls. However, if the walls are constructed

with concrete, or have metal, or metal mesh, the effective range will decrease if such materials are

between the devices.

What Is in the Box

The product package should contain the following items:

• NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3

• Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3

• NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 Resource CD, including:

– Wireless Assistant

– Configuration Utility Software

– This Reference Manual

• Warranty card

• Support information card

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the

carton, including the original packing materials, in case you need to return the product for repair.

WG311 v3 Default Wireless Settings

If this is a new wireless network installation, use the factory default settings to set up the network

and verify wireless connectivity. If this is an addition to an existing wireless network, you will

need to identify the wireless network and wireless security settings that are already defined.

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-3

v3.0, February 2007

Your WG311 v3 Wireless PCI Adapter factory default basic settings are:

• Network Name Service Set Identification (SSID): Any (First available network)

• Network Mode (Infrastructure or Ad-hoc): Infrastructure

• Data security WEP, WPA2-PSK, or WPA-PSK encryption: Disabled

Installation

The instructions in this chapter explain how to install the WG311 v3 Wireless PCI Adapter to

connect to a network with an access point or router. Wireless security, advanced settings, and

Computer-to-Computer (Ad Hoc) instructions are covered in Chapter 2, “Network Connections

and Wireless Security”.

To install the WG311 v3 Wireless PCI Adapter:

1. First, install the NETGEAR software:

Insert the NETGEAR CD. If the CD main page does not appear, double click Autorun.exe on

the CD.

a. Click Install the Software. The Check for Updates window opens.

Note: In order for the WG311 v3 Wireless PCI Adapter to communicate with a

wireless access point or wireless adapter, all devices must be set up to use the

same wireless network name (SSID).

Figure 1-1

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-4

v3.0, February 2007

b. If you are connected to the Internet, click Check for Updates. If not, you can choose to

install from the CD.

c. Follow the Wizard steps and click Next to continue, and to install the software.

d. When the software has been installed the Connection Wizard prompts you to shut down

the computer.

2. Now, install the wireless PCI adapter.

e. Shut down your computer and unplug the power cord.

f. Open the case and insert your WG311 v3 into a PCI slot.

g. Connect the antenna to the adapter and position the antenna to the up position.

h. Close the case, plug the power cord back in, and restart your computer.

3. Use the Smart Wizard to set up your wireless PCI adapter.

a. Windows 2000, 98SE/ME users go to Step b. Windows XP or Vista users can set up the

wireless adapter either with the NETGEAR Smart Wizard (recommended) or the

Windows configuration utilities.

Figure 1-2

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-5

v3.0, February 2007

• NETGEAR Smart Wizard: Reveals more information about each network and

makes it easier to troubleshoot network connection problems.

• Windows configuration utilities: See the Windows documentation or “Using

Windows XP and Vista Wireless Configuration Utilities” at:

http://documentation.netgear.com/reference/enu/winzerocfg/index.htm

b. Click Next to accept the NETGEAR Smart Wizard.

You will be prompted to let the wizard help you connect to a network (recommended).

c. Click Next to accept.

Figure 1-3

Figure 1-4

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-6

v3.0, February 2007

4. Connect to a wireless network.

a. Select the wireless network from the drop-down list, and the wizard records your choice.

If the network uses security, then the Smart Wizard detects it.

b. Follow the Wizard steps for Security (if used) and for saving a Profile.

c. After you have reviewed the settings, click Finish.

The WG311 v3 icon appears in the system tray and on the desktop. The wizard

initiates your wireless connection. It could take up to a minute for your wireless

connection to be established.

Figure 1-5

Note: Hidden networks do not broadcast the Network Name (SSID). These

networks are in the drop-down list, but the Network Name (SSID) is blank.

Hidden

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-7

v3.0, February 2007

The Smart Wizard Settings page opens.

5. Use the status bar to verify your wireless connectivity.

For more details about connecting, see “Connecting to Wireless Networks and the Internet” on

page 1-7.

Connecting to Wireless Networks and the Internet

The WG311 v3 has indicators in three locations that show the status of your connection to a

wireless network and to the Internet:

• WG311 v3 Icon: After you install the WG311 v3 software, the icon appears on the

desktop and in the lower right of the Windows task bar. It is color coded to show the status of

the connection.

• Smart Wizard Status Bar: Clicking on the system tray icon opens the Smart Wizard. The

status bar at the bottom of the page shows details about your wireless and Internet connection.

See “The Smart Wizard Status Bar” on page 1-8.

• WG311 v3 Wireless PCI Adapter LED: The LED on the wireless PCI adapter shows the

network connection. Solid indicates a connection. The LED blinks when the wireless PCI

adapter is looking for a network association.

Figure 1-6

NETGEAR 54 Mbps Wireless PCI Adapter WG311 v3 User Manual

1-8

v3.0, February 2007

WG311 v3 Icon Colors

The WG311 v3 icon is on the desktop and in the Windows System Tray. The System Tray is

located on one end of the taskbar in the Microsoft Windows desktop.

The Smart Wizard Status Bar

Click the WG311 v3 icon to open the Smart Wizard so you can view the status bar. The Smart

Wizard Settings page opens. The status bar is located at the bottom of the Settings page.

The following table describes how to interpret the Smart Wizard status bar.

Color Condition Description

Red The wireless PCI adapter has

no connection to any other

wireless node.

The wireless PCI adapter is not able to link to any other

wireless node or the link is lost. Check your configuration or

try moving to a location where the wireless signal quality is

better.

Yellow The wireless PCI adapter has

a connection with another

wireless node.

The wireless link is weak. You may need to move to a better

spot, such as closer to the wireless access point. Also, look

for possible interference such as a 2.4 GHz cordless phone or

large metal surface.

Green The wireless PCI adapter has

a connection with another

wireless node.

The wireless PCI adapter has established good

communication with an access point and the signal quality is

strong.

Figure 1-7

Wireless

network

Connection status

Security

Find a Network

Channel

Throughput

Signal

strength

La pagina sta caricando ...

Netgear WG311NAR Manuale utente

Questo manuale è adatto anche per

Netgear WG311NAR Manuale utente

in altre lingue

Documenti correlati

Altri documenti