Canon XF205 Manuale del proprietario

PUB. DIE-0459-000C

HD Camcorder

Instruction Manual

COPY

2

Important Usage Instructions

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO DRIPPING OR

SPLASHING.

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE

RECOMMENDED ACCESSORIES ONLY.

COPYRIGHT WARNING:

Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be

contrary to copyright laws.

The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to

disconnect the plug in case of an accident.

CAUTION:

• Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries.

• Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.

CA-930 identification plate is located on the bottom.

Only for European Union and EEA (Norway, Iceland and Liechtenstein)

These symbols indicate that this product is not to be disposed of with your household

waste, according to the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC)

and/or national legislation implementing those Directives.

If a chemical symbol is printed beneath the symbol shown above, in accordance with the

Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in

this battery or accumulator at a concentration above an applicable threshold specified in the Battery

Directive.

This product should be handed over to a designated collection point, e.g., on an authorized one-for-one

basis when you buy a new similar product or to an authorized collection site for recycling waste electrical

and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste

could have a possible impact on the environment and human health due to potentially hazardous

substances that are generally associated with EEE. Your cooperation in the correct disposal of this product

will contribute to the effective usage of natural resources.

For more information about the recycling of this product, please contact your local city office, waste

authority, approved scheme or your household waste disposal service or

visit www.canon-europe.com/weee

, or www.canon-europe.com/battery.

COPY

3

REGIONS OF USE

XF200 / XF205 are in compliance (as of June 2014) with the radio signal regulations of the regions listed below. For

details on other regions where they can be used, make inquiries with the contacts listed on the back cover of this

instruction manual.

Statement on EC directive

REGIONS

Radio channels prohibited

for outdoor use

Australia, Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,

Estonia, Finland, France, Germany, Greece, Hong Kong S.A.R., Hungary,

Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,

Netherlands, New Zealand, Norway, Poland, Portugal, Romania, Slovakia,

Slovenia, Spain, Sweden, Switzerland, United Kingdom

Channels 36 to 64

Russia, Singapore Not prohibited

Hereby, Canon Inc., declares that this RF400 is in compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC.

Please contact the following address for the original Declaration of Conformity:

CANON EUROPA N.V.

Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands

CANON INC.

30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

Model

ID0039: XF205 ID0040: XF200

Complies with

IDA Standards

DB007671

This product is installed with the WLAN

module which is certified to standards

set by IDA Singapore.

COPY

4

Trademark Acknowledgements

• SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.

• CompactFlash is a trademark of SanDisk Corporation.

• The CF Logo is a trademark of CompactFlash Association.

• Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United

States and/or other countries.

• Apple, App Store, Mac OS, Final Cut Pro are trademarks of Apple Inc., registered in the U.S. and other

countries.

• IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

• Google, Android, Google Play, are trademarks of Google Inc.

• Avid, Media Composer and NewsCutter are trademarks or registered trademarks of Avid Technology, Inc. or

its subsidiaries in the United States and/or other countries.

• Wi-Fi is a registered trademark of the Wi-Fi Alliance.

• Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance.

• WPS as used on the camcorder's settings, onscreen displays and in this manual signifies Wi-Fi Protected

Setup.

• The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance.

• JavaScript is a trademark or registered trademark of Oracle Corporation, its affiliates or subsidiaries in the

United States and other countries.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.

• Other names and products not mentioned above may be trademarks or registered trademarks of their

respective companies.

• This device incorporates exFAT technology licensed from Microsoft.

• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT

COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED

MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2

PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET,

SUITE 300, DENVER, COLORADO 80206.

• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-

4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and

noncommercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4

compliant video. No license is granted or implied for any other use for MPEG-4 standard.

COPY

5

Highlights of the XF200 / XF205

The Canon HD Camcorder XF200 / XF205 is a compact-sized and highly portable camcorder that offers

superior video quality. The camcorder features a 1/2.84-type CMOS sensor and allows you to record in two

formats (MXF on CF cards or MP4 on SD cards). The following are some of the many features that will help you

turn your creative vision into reality.

HD Recording

1/2.84-type CMOS sensor and DIGIC DV 4 image

processor

The HD CMOS PRO sensor can capture video at an

effective pixel count of 2,910,000 pixels. Combined

with the advanced DIGIC DV 4 image processor and

the 20x wide-angle lens, it can deliver a center

resolution of 900 TV lines. Furthermore, thanks to

Canon’s high-sensitivity and noise reduction

technologies, you can get excellent video quality

with minimal noise even when recording in low-light

situations.

MXF and MP4 formats

You can choose the movie format according to your

workflow needs. You can record in MXF format

using the MPEG-2 Long GOP codec, in MP4 format

using the MPEG-4 AVC/H.264 codec, or in both

formats simultaneously. MXF clips are recorded as

Material eXchange Format (MXF files), compatible

with all major non-linear (NLE) editing software.

Flexible video and audio configuration

For MXF clips, the camcorder offers 3 resolution

sizes (1920x1080, 1440x1080 or 1280x720), 3

frame rate options and 3 bit rate options for a total

of 11 video configurations (A 55). Audio is

recorded as linear PCM audio using 2 or 4 channels

(A 96).

For MP4 clips, the camcorder offers 3 resolution

sizes (1920x1080, 1280x720 or 640x360), 2 frame

rate options and 5 bit rate options for a total of 5

possible video configurations (A 55).

Operability and Adaptability

Freely customizable compact design

The camcorder offers maximum operability for a

single camera operator. It features 3 separate rings

for independent focus, zoom and iris operation. The

camcorder’s side grip can be easily adjusted up to

120 degrees to let you use whatever camera angle

you need (A 35). Additionally, gain, shutter and iris

controls can be adjusted manually or automatically

giving you the freedom to decide to what extent you

want to control every aspect of the image.

Improved displays

The camcorder features an 8.8 cm (3.5 in.) OLED

display (equivalent to 1,230,000 dots) that excels in

color reproduction, contrast and responsiveness

and is easy to use even in bright outdoors. The

viewfinder, on the other hand, offers a high-

resolution LCD screen (also equivalent to 1,230,000

dots) with a wide angle of view of approx. 28.2°. The

viewfinder can be tilted 68° vertically to ensure a

comfortable fit in various shooting conditions.

Recording media

The camcorder records MXF clips to CF cards and

MP4 clips to SD cards. It features two CF card slots

that you can use to record continuously, one after

the other, using relay recording (A 42), or

simultaneously using double slot recording (A 42).

You can even record MP4 clips to the SD card while

recording an MXF clip on one or both CF cards

(A 121).

Work with major NLE software

The Canon XF Utility software and various XF

plugins are available as free downloads from your

local Canon Web site. Canon XF Utility allows you

to easily save, manage and play back your MXF

clips, while the XF plugins let you smoothly link them

to major NLE software* to continue your editing

workflow. For details, refer to

Saving MXF Clips

(A 166).

The supplied software Data Import Utility allows

you to save MP4 clips to a computer and even join

split MP4 files into a single file for editing. For details,

refer to

Saving MP4 Clips

(A 168).

*Refer to

Saving Clips to a Computer

(A 166) for details

on compatible software.

Pro-level remote operation

The camcorder can be used with the optional

RC-V100 Remote Controller for remote operation of

many advanced functions, including iris, gain and

even custom picture settings.

COPY

6

Versatile Artistic Expression

Special recording modes

The special recording modes (A 116) give you

more creative control over your recordings. You can

create a slow motion or fast motion effect in your

recordings, record a certain number of frames at a

set interval (ideal for nature shots and other subjects

with little movement) or record a certain number of

frames every time you press a button (ideal for stop

motion animation).

Custom picture settings

With custom picture settings (A 130), you can

enjoy unparalleled image control to deliver the “look”

you want by adjusting parameters, such as gamma

and sharpness.

Advanced Professional Features and

Flexibility

Wired and Wi-Fi network functions (A 171)

You can connect the camcorder to other devices via

wired (Ethernet) connection or Wi-Fi to enjoy a

variety of functions. For example, you can transfer

recordings to an FTP server or use the Web browser

on a connected device to remotely operate the

camcorder (Browser Remote) or to play back the

recordings on the camcorder (Playback via

Browser). Also, using the IP streaming function

(A 192), you can broadcast the camcorder’s live

video over IP to a compatible decoder connected to

the same network.

Pro-level connectivity

The camcorder offers two terminals for professional

level connectivity. Use the 3G/HD-SDI terminal to

output the uncompressed HD video signal along

with embedded audio and SMPTE time code (LTC)

in a format that can be used for external recording.

Meanwhile, the MON. terminal offers the best video

output for an external monitor, including the option

to overlay the camcorder’s onscreen displays.

Genlock synchronization (A 93), the TIME CODE

terminal (A 94, 95) and GENLOCK/SYNC OUT

terminal allow the camcorder to be part of any multi-

camera shooting setup.

Infrared recording

Record in darkness using infrared recording

(A 124). With the built-in infrared light, you can

record nocturnal animals in their natural environment

or other such scenes.

Customization

The camcorder features several customization

options. You can assign often-used functions to

assignable buttons (A 127) so that you can call up

those functions with the press of a single button.

You can also register frequently-used menu settings

in an easy-to-access personal menu (My Menu,

A 30). Custom functions (A 139) and custom

onscreen displays (A 140) give you even more

freedom to control many aspects of the camcorder’s

operation. Save custom picture and menu settings

to an SD card so that you can transfer your setting

preferences to other XF200 / XF205 camcorders in

order to use them in the same way.

Other Functions

• Direct setting mode (A 57)

Change main camera functions while checking

the image on the screen using only the joystick.

• Assistance functions

Peaking and magnification (A 84) can be helpful

when you use manual focus, onscreen markers

(A 88) can be very useful to help you frame your

video, and zebra patterns (A 89) can give you a

reference point to avoid overexposures.

• Video scopes (A 106)

Check the brightness of the image using the

waveform monitor, the color of the image using

the vectorscope, or the focus using the edge

monitor.

• Intelligent System

When using battery packs compatible with

Intelligent System, the camcorder will display an

estimate, in minutes, of the remaining recording/

playback time using the battery pack (A 25). You

can also check the battery life indicator and other

information on the [Battery/Hour Meter] status

screen (A 215).

• Multiple audio recording options (A 96)

The camcorder offers 2- or 4-channel linear PCM

audio recording for MXF clips and 2-channel AAC

audio recording for MP4 clips. You can use the

camcorder’s built-in microphone, external

microphones with a ∅ 3.5 mm mini-stereo plug

(MIC terminal), or external audio input sources

with an XLR plug (INPUT 1/INPUT 2 terminals with

+48 V phantom power supply). The camcorder

even has a convenient microphone holder with

cable clamp for external microphones.

• Metadata and GPS information (A 109, 112)

You have the option to add various metadata

fields to your MXF clips. Some of the information

requires using Canon XF Utility or the Browser

Remote application. Additionally, you can connect

the optional GP-E2 GPS Receiver to the

camcorder to automatically add GPS information

to your recordings. Using Canon XF Utility you

can then organize or search MXF clips by GPS

information.

COPY

7

1. Introduction 11

About this Manual 11

Conventions Used in this Manual 11

Supplied Accessories 13

Names of Parts 14

WL-D6000 Wireless Controller 21

2. Preparations 23

Preparing the Power Supply 23

Using a Battery Pack 23

Using a Household Power Outlet 25

Turning the Camcorder On and Off 26

Date, Time and Language Settings 27

Setting the Date and Time 27

Changing the Time Zone 27

Displaying the Date and Time while Recording 28

Changing the Language 28

Using the Menus 29

Selecting an Option from the Menu 29

Using the Customized Submenu (My Menu) 30

Preparing the Camcorder 32

Attaching the Microphone Holder Unit 32

Attaching the Lens Hood 32

Using the Viewfinder 32

Using the OLED Panel 33

Adjusting the Viewfinder/OLED Screen 34

Adjusting the Color Balance of the OLED

Screen 34

Setting the Screen to Black & White 35

Adjusting the Grip Unit 35

Attaching the Shoulder Strap 36

Removing and Attaching the Terminal Covers 36

Using a Tripod 37

Preparing Recording Media 38

Inserting a CF Card 39

Checking the Status of the CF Card Slots 39

Removing a CF card 40

Inserting and Removing an SD Card 40

Initializing the Recording Media 41

Switching Between the CF Card Slots 41

Selecting the CF Card Recording Method 42

Checking the Available Recording Time on a

Recording Media 43

Recovering Data on a Recording Media 43

Remote Operation of the Camcorder 44

Using the Supplied Wireless Controller 44

Using the Optional RC-V100 Remote

Controller 45

3. Recording 47

Recording Video 47

Preparing to Record 47

Recording 48

Remote Operation Using Browser Remote 50

Onscreen Displays 51

Power Save Mode 54

Using the Fan 54

Video Configuration: Movie Format, Bit Rate,

Resolution and Frame Rate 55

Changing Main Camera Functions with the

Joystick 57

Using the Direct Setting Mode 57

Shutter Speed 58

Automatic Shutter 59

Manual Shutter 60

Flicker Reduction 61

Gain 62

Selecting the Gain Level 62

Automatic Gain Control (AGC) 62

Manual Gain 63

Aperture 65

Automatic Aperture 65

Manual Aperture 66

ND Filter 67

Exposure Compensation - AE Shift 67

Light Metering Mode 68

White Balance 69

Auto White Balance (AWB) 70

Preset White Balance/Color Temperature 71

Custom White Balance 72

Zooming 74

Selecting the Zoom Mode 74

Using the Zoom Ring 75

Using the Zoom Rockers on the Camcorder 75

Remote Operation 78

Soft Zoom Control 79

Using Optional Conversion Lenses 80

Table of Contents

COPY

8

Adjusting the Focus 81

Autofocus (AF) Mode 81

Manual Focus (MF) 83

Push AF 85

Detecting and Focusing On Faces 85

Focus Limit and Macro Shooting 86

Image Stabilizer 87

Onscreen Markers and Zebra Patterns 88

Displaying Onscreen Markers 88

Displaying Zebra Patterns 89

Setting the Time Code 90

Selecting the Running Mode 90

Putting the Time Code Display on Hold 91

Setting the User Bit 92

Synchronizing with an External Device 93

Connecting an External Device 93

Reference Video Signal Input (Genlock

Synchronization) 93

Time Code Signal Input 94

Reference Video Signal Output 95

Time Code Signal Output 95

Recording Audio 96

Audio Settings and Recorded Audio Channels 96

Selecting the Number of Recorded Audio

Channels 98

Connecting an External Microphone or External

Audio Input Source to the Camcorder 98

Using the Built-in Microphone or MIC Terminal 99

Using the INPUT 1/INPUT 2 Terminals 101

Adjusting the Audio Level 103

Monitoring the Audio with Headphones 104

Colors Bars/Audio Reference Signal 105

Recording Color Bars 105

Recording an Audio Reference Signal 105

Video Scopes 106

Displaying a Video Scope 106

Configuring the Waveform Monitor 106

Configuring the Vectorscope 107

Configuring the Edge Monitor 107

Adding Marks to MXF Clips while Recording 108

Adding Shot Marks while Recording 108

Adding an $ Mark or % Mark to the Last Clip

Recorded 108

Using Metadata 109

Setting a User Memo Created with Canon XF

Utility 109

Setting a User Memo Using Browser

Remote 110

Recording GPS Information (Geotagging) 112

Reviewing a Recording 114

File Numbering 115

Special Recording Modes 116

Interval Recording Mode 116

Frame Recording Mode 117

Slow & Fast Motion Mode 118

Pre-recording Mode 120

Simultaneous Recording of MXF and MP4

Clips 121

Recording in MP4 Backup Recording Mode 122

Infrared Recording 124

Activating Infrared Mode 124

Using the Infrared Light 124

Using the Focal Length Guide 126

4. Customization 127

Assignable Buttons 127

Changing the Assigned Function 127

Using an Assignable Button 128

Custom Picture Settings 130

Selecting Custom Picture Files 130

Editing a Custom Picture File’s Settings 131

Renaming Custom Picture Files 131

Protecting Custom Picture Files 131

Transferring Custom Picture Files 132

Embedding Custom Picture Settings in a

Recording 133

Available Custom Picture Settings 133

Customizing Functions and Onscreen

Displays 139

Customizing Functions 139

Customizing Onscreen Displays 140

Saving and Loading Camera Settings 141

Saving Camera Settings to an SD Card 141

Loading Camera Settings from an SD Card 141

5. Playback 143

Playback 143

MXF and MP4 Clip Index Screens 143

Playing Back Clips 145

Onscreen Displays 145

Playback Controls 146

Adjusting the Volume 147

Clip Operations 148

Using the Clip Menu 149

Displaying Clip Information 149

Adding $ Marks or % Marks 150

Deleting $ Marks or % Marks 151

Copying Clips 151

Deleting Clips 152

Deleting the User Memo and GPS

Information 153

Copying a Custom Picture File Embedded in a

Clip 153

COPY

9

Displaying an Index Screen of Shot Marks 153

Displaying a Frame Index Screen of a Single

Clip 154

Adding Shot Marks 155

Deleting Shot Marks 155

Changing a Clip’s Thumbnail 156

6. External Connections 157

Video Output Configuration 157

Recording Video Signal Configuration and Video

Output Configuration by Terminal 157

Playback Video Configuration and Video Output

Configuration by Terminal 158

Connecting to an External Monitor 160

Connection Diagram 160

Using the 3G/HD-SDI Terminal 161

Using the MON. Terminal 161

Using the HDMI OUT Terminal 162

Using the AV OUT Terminal 162

SD Output 163

Superimposing Onscreen Displays to Appear on

an External Monitor 163

Audio Output 164

Selecting the Audio Channel 164

Synchronizing the Video with the Audio being

Monitored 165

Selecting the Output Level of the AV OUT

Terminal 165

Saving Clips to a Computer 166

Saving MXF Clips 166

Saving MP4 Clips 168

Connecting the Camcorder to a Computer 169

7. Network Functions 171

About the Network Functions 171

Connecting to a Wi-Fi Network 173

Wi-Fi Protected Setup (WPS) 173

Searching for Access Points 174

Manual Setup 176

Camera Access Point 176

Configuring the IP Address Settings 177

Saving the Configuration 177

Connecting to a Wired (Ethernet) Network 178

Selecting a Network Connection 179

Changing Network Settings 180

Browser Remote: Controlling the Camcorder from

a Network Device 181

Setting Up Browser Remote 181

Starting Browser Remote 182

Real-Time Proxy Transfer 187

FTP File Transfer 188

Preparations 188

FTP Transfer in Mode 189

FTP Transfer in Mode 190

IP Streaming 192

Preparations 192

Streaming Video over IP 193

Playback via Browser 195

8. Photos 197

Taking Photos 197

Taking Photos in Mode 197

Capturing Photos in Mode 197

Photo Playback 199

Displaying the [Photos] Index Screen 199

Viewing Photos 199

Deleting Photos 200

9. Additional Information 201

Menu Options 201

Displaying the Status Screens 211

Troubleshooting 221

List of Messages 226

Handling Precautions 231

Maintenance/Others 234

Optional Accessories 235

Specifications 238

Index 243

COPY

10

COPY

1

11

Introduction

About this Manual

Thank you for purchasing the Canon XF200 / XF205. Please read this manual carefully before you use the

camcorder and retain it for future reference. Should the camcorder fail to operate correctly, refer to

Troubleshooting

(A 221).

Conventions Used in this Manual

• IMPORTANT: Precautions related to the camcorder’s operation.

• NOTES: Additional topics that complement the basic operating procedures.

• A: Reference page number.

• : Text that applies only to the model shown in the icon.

• The following terms are used in this manual.

“Screen” refers to the OLED screen and the viewfinder screen.

“CF card” refers to a CompactFlash (CF) card.

“SD card” refers to an SD, SDHC or SDXC memory card.

“Recording media” refers to CF cards and SD cards.

When not specified, “access lamps” refers to either or both of the CF card access lamps (CF2/CF3) and the

SD card access lamp.

“Press SET” refers to pressing down the joystick itself (A 29).

• Photographs in the manual are simulated pictures taken with a still camera. Some screenshots have been

altered to make them easier to read.

• Illustrations in the manual show the XF205.

COPY

About this Manual

12

Operating modes and Format

A full icon (like ) indicates that the function

described can be used in the operating mode

shown or for recordings made in the movie

format shown in the icon; an empty icon (like

) indicates that the function cannot be

used. For details refer to

Tur ning th e Camc order

On and Off

(A 26) or

Selecting the Movie

Format

(A 55).

When a function requires the use of the menu,

the quick reference shows the submenus and,

when applicable, the default setting for the menu

item. The example illustration indicates that you

can find the function by selecting the

[w Other Functions] menu and then the [Fan]

menu item.

The arrow > is used to abbreviate menu

selections. For a detailed explanation on how to

use the menus, refer to

Using the Menus

(A 29). For a concise summary of all available

menu options and settings, refer to the appendix

Menu Options

(A 201).

When a procedure requires selecting an option,

the available options are listed within or after the

procedure. Brackets [ ] are used to refer to menu

options as they are displayed on screen.

COPY

13

Supplied Accessories

The following accessories are supplied with the camcorder.

* The Data Import Utility Software Guide (PDF file) is included in the CD-ROM. For details about the software, refer to this Software

Guide.

CA-930 Compact Power Adapter

(incl. power cord)

DC-930 DC Cable BP-955 Battery Pack

(incl. terminal cover)

Lens Hood with Lens Barrier Lens Cap Eye cup

WL-D6000 Wireless Controller

(incl. CR2025 Lithium Battery)

Microphone Holder Unit SS-1200 Shoulder Strap

Data Import Utility

Software CD-ROM*

COPY

Names of Parts

14

Names of Parts

1

8

9

10

11

12

13 14 15 16 17

18

19

20

21 23

22 24

25

26

27 28

234

5 6 7

Operation panel

햲

(A 20)

Operation panel

햳

(A 20)

1 Protective cover for audio controls (A 96)

2 Strap mount (A 36)

3 INFRARED switch (A 124)

4 ZOOM SPEED (zoom speed of the handle's zoom

rocker) switch (A 75)

5 CF card slot covers for CF card slots A (left) and B

(right)

6 POWER SAVE button (A 54)

7 Exhaust ventilation outlet (A 54)

8CF2 (CF card slot A) and CF3 (CF card slot B)

access indicators (A 39)

9 CF card release buttons for CF card slots A (left)

and B (right) (A 40)

10 CF card slots A (left) and B (right) (A 39)

11 Q switch (A 26)

12 Power indicator (A 26)

13 Lens hood (A 32)

14 Lens barrier switch (A 47)

15 Focus ring (A 83)

16 Zoom ring (A 75)

17 Iris ring (A 66)

18 PUSH AF (momentary autofocus) button (A 85)

19 IRIS (ND) (aperture mode/ND filter) switch (A 65)

20 FOCUS (focus mode) switch (A 81, 83)

21 PEAKING button (A 84) /

Assignable button 1 (A 127)

22 ZEBRA button (A 89)/

Assignable button 2 (A 127)

23 FULL AUTO switch (A 49)

24 CF card slot cover switches for CF card slots A

(left) and B (right) (A 39)

25 SHUTTER switch (A 58)

26 GAIN switch (A 62)

27 WHITE BAL. (white balance) switch (A 69)

28 Å (white balance adjustment) button (A 72)

COPY

15

Names of Parts

29

33 34 35 36 37

38

40

39 4241

30

31

32

29 GENLOCK/SYNC OUT (synchronization)

terminal (A 93, 95)

30 TIME CODE terminal (A 94, 95)

31 MON. (monitor output) terminal (A 160,

161)

32 3G/HD-SDI terminal (A 160, 161)

33 Strap mount (A 36)

34 REMOTE terminal (A 45)

For connecting the optional RC-V100 Remote

Controller or commercially available remote

controllers.

35 USB terminal (A 169)

36 MIC (microphone) terminal (A 99)

37 Attachment sockets for the microphone holder

unit (A 32)

38 INPUT 1 (right) and INPUT 2 (left) terminals (XLR)

(A 101)

39 Air intake vent (A 54)

40 Grip belt (A 35)

41 Adjustable grip unit (A 35)

42 Lens hood lock screw (A 32)

COPY

Names of Parts

16

43

48

49

50

51

52

44

45

46

47

43 Microphone lock screw (A 98)

44 Microphone holder (A 98)

45 Microphone cable clamp (A 98)

46 Lens barrier (A 47)

47 Instant AF sensor (A 81)

48 Built-in stereo microphone (A 99)

49 Front tally lamp (A 48)

50 Remote sensor (A 44)

51 Infrared light (A 124)

52 START/STOP button (A 48, 121)

COPY

17

Names of Parts

53

61

63

64

65

62

68

69

70

71

72

73

54

55

56

57

58

59

60

66

67

53 MENU button (A 29)

54 Joystick (A 29)/SET button (A 29)

55 CANCEL button (A 29)

56 POWERED IS button (A 87)/

Assignable button 3 (A 127)

57 OLED screen (A 33, 34)

58 SD card slot cover (A 40)

59 SD card access indicator (A 48, 121, 197)

60 SD card slot (A 40)

61 Viewfinder (A 32, 34)

62 Eye cup (A 33)

63 Dioptric adjustment lever (A 33)

64 Viewfinder unit

65 Battery compartment (A 24)

66 START/STOP button (A 48, 121)

67 UNLOCK (unlock the grip) switch (A 35)

68 × (headphone) terminal (A 104)

69 AV OUT terminal (A 160, 162)

70 HDMI OUT terminal (A 160, 162)

71 DC IN terminal (A 25)

72 LAN access indicator (A 178)

73 LAN terminal (Ethernet) (A 178)

COPY

Names of Parts

18

74

82 83 85 86

84

75 76 77 78 79 80 81

74 Accessory shoe

For attaching accessories such as the optional

VL-10Li II Battery Video Light.

75 Built-in speaker (A 147)

76 START/STOP lock lever (A 48)

77 START/STOP button (A 48, 121)

78 Grip zoom rocker (A 75)

79 MAGN. (magnification) button (A 84)/

Assignable button 4 (A 127)

80 Strap mount (A 36)

81 BATTERY RELEASE lever (A 24)

82 Front tally lamp (A 48)

83 – dials for CH1 (left) and CH2 (right)

(A 103)

84 Rear tally lamp (A 48)

85 Handle zoom rocker (A 77)

86 Handle socket for 0.64 cm (1/4") screws

COPY

19

Names of Parts

87

88

8990 91

87 Attachment sockets for the optional TA-100 Tripod

Adapter (A 37)

88 Tripod base screws (A 37)

89 Tripod base for tripods with 0.64 cm (1/4") screws

(A 37)

90 Air intake vent (A 54)

91 Tripod socket (A 37)

COPY

Names of Parts

20

Operation panels

Operation panel 햲 Operation panel 햳

1

2

3

5

4

10

11

12

13

14

15

6

7

8

9

1 Audio level switches for CH1 (left) and CH2 (right)

(A 103)

2 AUDIO IN (audio input) selection switches for CH1

(left) and CH2 (right) (A 99, 101)

3 INPUT 1 (left) / INPUT 2 (right) audio source

selection switches (A 101)

4 Ò (play/pause) button (A 145)/

Assignable button 6 (A 127)

5 Ø (fast reverse playback) button (A 146)/

Assignable button 5 (A 127)

6 Ú (skip backward) button (A 146)/

Assignable button 8 (A 127)

7 SLOT SELECT (CF card slot selection) button

(A 41, 144)

8INDEX button (A 144)/

u (review recording) button (A 114)

9 HEADPHONE+ button (A 147)/

Assignable button 11 (A 127)

10 × (fast playback) button (A 146)/

Assignable button 7 (A 127)

11 Ù (skip forward) button (A 146)/

Assignable button 10 (A 127)

12 Ñ (stop) button (A 145)/

Assignable button 9 (A 127)

13 DISP. (display) button (A 51, 145)

14 WFM (waveform monitor) button (A 106)/

Assignable button 13 (A 127)

15 HEADPHONE- button (A 147)/

Assignable button 12 (A 127)

COPY

La pagina sta caricando ...

Canon XF205 Manuale del proprietario

Questo manuale è adatto anche per

Canon XF205 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti